@@ -1803,6 +1803,9 @@ static int bmc150_accel_resume(struct device *dev)
bmc150_accel_fifo_set_mode(data);
mutex_unlock(&data->mutex);
+ if (data->resume_callback)
+ data->resume_callback(dev);
+
return 0;
}
#endif
@@ -28,6 +28,108 @@ static const struct acpi_device_id bmc150_acpi_dual_accel_ids[] = {
{ }
};
+/*
+ * The DUAL250E ACPI device for 360° hinges type 2-in-1s with 1 accelerometer
+ * in the display and 1 in the hinge has an ACPI-method (DSM) to tell the
+ * ACPI code about the angle between the 2 halves. This will make the ACPI
+ * code enable/disable the keyboard and touchpad. We need to call this to avoid
+ * the keyboard being disabled when the 2-in-1 is turned-on or resumed while
+ * fully folded into tablet mode (which gets detected with a HALL-sensor).
+ * If we don't call this then the keyboard won't work even when the 2-in-1 is
+ * changed to be used in laptop mode after the power-on / resume.
+ *
+ * This DSM takes 2 angles, selected by setting aux0 to 0 or 1, these presumably
+ * define the angle between the gravity vector measured by the accelerometer in
+ * the display (aux0=0) resp. the base (aux0=1) and some reference vector.
+ * The 2 angles get subtracted from each other so the reference vector does
+ * not matter and we can simply leave the second angle at 0.
+ */
+
+#define BMC150_DSM_GUID "7681541e-8827-4239-8d9d-36be7fe12542"
+#define DUAL250E_SET_ANGLE_FN_INDEX 3
+
+struct dual250e_set_angle_args {
+ u32 aux0;
+ u32 ang0;
+ u32 rawx;
+ u32 rawy;
+ u32 rawz;
+} __packed;
+
+static bool bmc150_acpi_set_angle_dsm(struct i2c_client *client, u32 aux0, u32 ang0)
+{
+ struct acpi_device *adev = ACPI_COMPANION(&client->dev);
+ struct dual250e_set_angle_args args = {
+ .aux0 = aux0,
+ .ang0 = ang0,
+ };
+ union acpi_object args_obj, *obj;
+ guid_t guid;
+
+ if (!acpi_dev_hid_uid_match(adev, "DUAL250E", NULL))
+ return false;
+
+ guid_parse(BMC150_DSM_GUID, &guid);
+
+ if (!acpi_check_dsm(adev->handle, &guid, 0, BIT(DUAL250E_SET_ANGLE_FN_INDEX)))
+ return false;
+
+ /*
+ * Note this triggers the following warning:
+ * "ACPI Warning: \_SB.PCI0.I2C2.ACC1._DSM: Argument #4 type mismatch -
+ * Found [Buffer], ACPI requires [Package]"
+ * This is unavoidable since the _DSM implementation expects a "naked"
+ * buffer, so wrapping it in a package will _not_ work.
+ */
+ args_obj.type = ACPI_TYPE_BUFFER;
+ args_obj.buffer.length = sizeof(args);
+ args_obj.buffer.pointer = (u8 *)&args;
+
+ obj = acpi_evaluate_dsm(adev->handle, &guid, 0, DUAL250E_SET_ANGLE_FN_INDEX, &args_obj);
+ if (!obj) {
+ dev_err(&client->dev, "Failed to call DSM to enable keyboard and touchpad\n");
+ return false;
+ }
+
+ ACPI_FREE(obj);
+ return true;
+}
+
+static bool bmc150_acpi_enable_keyboard(struct i2c_client *client)
+{
+ /*
+ * The EC must see a change for it to re-enable the kbd, so first
+ * set the angle to 270° (tent/stand mode) and then change it to
+ * 90° (laptop mode).
+ */
+ if (!bmc150_acpi_set_angle_dsm(client, 0, 270))
+ return false;
+
+ /* The EC needs some time to notice the angle being changed */
+ msleep(100);
+
+ return bmc150_acpi_set_angle_dsm(client, 0, 90);
+}
+
+static void bmc150_acpi_resume_work(struct work_struct *work)
+{
+ struct bmc150_accel_data *data =
+ container_of(work, struct bmc150_accel_data, resume_work.work);
+
+ bmc150_acpi_enable_keyboard(data->second_device);
+}
+
+static void bmc150_acpi_resume_handler(struct device *dev)
+{
+ struct bmc150_accel_data *data = iio_priv(dev_get_drvdata(dev));
+
+ /*
+ * Delay the bmc150_acpi_enable_keyboard() call till after the system
+ * resume has completed, otherwise it will not work.
+ */
+ schedule_delayed_work(&data->resume_work, msecs_to_jiffies(1000));
+}
+
/*
* Some acpi_devices describe 2 accelerometers in a single ACPI device,
* try instantiating a second i2c_client for an I2cSerialBusV2 ACPI resource
@@ -56,12 +158,20 @@ static void bmc150_acpi_dual_accel_probe(struct i2c_client *client)
board_info.irq = acpi_dev_gpio_irq_get(adev, 1);
data->second_device = i2c_acpi_new_device(&client->dev, 1, &board_info);
+
+ if (!IS_ERR(data->second_device) && bmc150_acpi_enable_keyboard(data->second_device)) {
+ INIT_DELAYED_WORK(&data->resume_work, bmc150_acpi_resume_work);
+ data->resume_callback = bmc150_acpi_resume_handler;
+ }
}
static void bmc150_acpi_dual_accel_remove(struct i2c_client *client)
{
struct bmc150_accel_data *data = iio_priv(i2c_get_clientdata(client));
+ if (data->resume_callback)
+ cancel_delayed_work_sync(&data->resume_work);
+
i2c_unregister_device(data->second_device);
}
#else
@@ -6,6 +6,7 @@
#include <linux/iio/iio.h>
#include <linux/mutex.h>
#include <linux/regulator/consumer.h>
+#include <linux/workqueue.h>
struct regmap;
struct i2c_client;
@@ -62,6 +63,8 @@ struct bmc150_accel_data {
int64_t timestamp, old_timestamp; /* Only used in hw fifo mode. */
const struct bmc150_accel_chip_info *chip_info;
struct i2c_client *second_device;
+ void (*resume_callback)(struct device *dev);
+ struct delayed_work resume_work;
struct iio_mount_matrix orientation;
};
Some 360 degree hinges (yoga) style 2-in-1 devices use 2 bmc150 accels to allow the OS to determine the angle between the display and the base of the device, so that the OS can determine if the 2-in-1 is in laptop or in tablet-mode. On Windows both accelerometers are read (polled) by a special service and this service calls the DSM (Device Specific Method), which in turn translates the angles to one of laptop/tablet/tent/stand mode and then notifies the EC about the new mode and the EC then enables or disables the builtin keyboard and touchpad based in the mode. When the 2-in-1 is powered-on or resumed folded in tablet mode the EC senses this independent of the DSM by using a HALL effect sensor which senses that the keyboard has been folded away behind the display. At power-on or resume the EC disables the keyboard based on this and the only way to get the keyboard to work after this is to call the DSM to re-enable it. Call the DSM on probe() and resume() to fix the keyboard not working when powered-on / resumed in tablet-mode. This patch was developed and tested on a Lenovo Yoga 300-IBR. Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- Changes in v2: - Use acpi_dev_hid_uid_match() to check that we are dealing with a "DUAL250E" device in bmc150_acpi_set_angle_dsm() - Rewrap some comments at 80 chars limit --- drivers/iio/accel/bmc150-accel-core.c | 3 + drivers/iio/accel/bmc150-accel-i2c.c | 110 ++++++++++++++++++++++++++ drivers/iio/accel/bmc150-accel.h | 3 + 3 files changed, 116 insertions(+)