diff mbox series

[v4,14/32] media: ov2680: Add support for more clk setups

Message ID 20230802173046.368434-15-hdegoede@redhat.com (mailing list archive)
State New, archived
Headers show
Series media: ov2680: Bugfixes + ACPI + selection(crop-tgt) API support | expand

Commit Message

Hans de Goede Aug. 2, 2023, 5:30 p.m. UTC
On ACPI systems the following 2 scenarios are possible:

1. The xvclk is fully controlled by ACPI powermanagement, so there
   is no "xvclk" for the driver to get (since it is abstracted away).
   In this case there will be a "clock-frequency" device property
   to tell the driver the xvclk rate.

2. There is a xvclk modelled in the clk framework for the driver,
   but the clk-generator may not be set to the right frequency
   yet. In this case there will also be a "clock-frequency" device
   property and the driver is expected to set the rate of the xvclk
   through this frequency through the clk framework.

Handle both these scenarios by switching to devm_clk_get_optional()
and checking for a "clock-frequency" device property.

This is modelled after how the same issue was fixed for the ov8865 in
commit 73dcffeb2ff9 ("media: i2c: Support 19.2MHz input clock in ov8865").

Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 drivers/media/i2c/ov2680.c | 26 ++++++++++++++++++++++++--
 1 file changed, 24 insertions(+), 2 deletions(-)
diff mbox series

Patch

diff --git a/drivers/media/i2c/ov2680.c b/drivers/media/i2c/ov2680.c
index cf84701a6a5a..42be7b094d5d 100644
--- a/drivers/media/i2c/ov2680.c
+++ b/drivers/media/i2c/ov2680.c
@@ -698,6 +698,7 @@  static int ov2680_parse_dt(struct ov2680_dev *sensor)
 {
 	struct device *dev = sensor->dev;
 	struct gpio_desc *gpio;
+	unsigned int rate = 0;
 	int ret;
 
 	/*
@@ -718,13 +719,34 @@  static int ov2680_parse_dt(struct ov2680_dev *sensor)
 
 	sensor->pwdn_gpio = gpio;
 
-	sensor->xvclk = devm_clk_get(dev, "xvclk");
+	sensor->xvclk = devm_clk_get_optional(dev, "xvclk");
 	if (IS_ERR(sensor->xvclk)) {
 		dev_err(dev, "xvclk clock missing or invalid\n");
 		return PTR_ERR(sensor->xvclk);
 	}
 
-	sensor->xvclk_freq = clk_get_rate(sensor->xvclk);
+	/*
+	 * We could have either a 24MHz or 19.2MHz clock rate from either DT or
+	 * ACPI... but we also need to support the weird IPU3 case which will
+	 * have an external clock AND a clock-frequency property. Check for the
+	 * clock-frequency property and if found, set that rate if we managed
+	 * to acquire a clock. This should cover the ACPI case. If the system
+	 * uses devicetree then the configured rate should already be set, so
+	 * we can just read it.
+	 */
+	ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
+				       &rate);
+	if (ret && !sensor->xvclk)
+		return dev_err_probe(dev, ret, "invalid clock config\n");
+
+	if (!ret && sensor->xvclk) {
+		ret = clk_set_rate(sensor->xvclk, rate);
+		if (ret)
+			return dev_err_probe(dev, ret,
+					     "failed to set clock rate\n");
+	}
+
+	sensor->xvclk_freq = rate ?: clk_get_rate(sensor->xvclk);
 	if (sensor->xvclk_freq != OV2680_XVCLK_VALUE) {
 		dev_err(dev, "wrong xvclk frequency %d HZ, expected: %d Hz\n",
 			sensor->xvclk_freq, OV2680_XVCLK_VALUE);