diff mbox

[v4] PCI: imx6: Add initial imx6sx support

Message ID 1457911870.16725.42.camel@googlemail.com (mailing list archive)
State New, archived
Delegated to: Bjorn Helgaas
Headers show

Commit Message

Christoph Fritz March 13, 2016, 11:31 p.m. UTC
Add initial PCIe support for the imx6 SoC derivate imx6sx.  PCI MSI support
is untested as the necessary suspend/resume quirk is not included in this
patch.

This patch is heavily based on patches by Richard Zhu.

[bhelgaas: factor out refclk enable, fix adjacent typos in imx6q-pcie.txt]
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Acked-by: Richard Zhu <Richard.Zhu@freescale.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
---
 .../devicetree/bindings/pci/fsl,imx6q-pcie.txt     |  8 +++-
 drivers/pci/host/pci-imx6.c                        | 53 ++++++++++++++++++++++
 2 files changed, 59 insertions(+), 2 deletions(-)

Comments

Christoph Fritz March 20, 2016, 7:30 a.m. UTC | #1
*ping*

On Mon, 2016-03-14 at 00:31 +0100, Christoph Fritz wrote:
> Add initial PCIe support for the imx6 SoC derivate imx6sx.  PCI MSI support
> is untested as the necessary suspend/resume quirk is not included in this
> patch.
> 
> This patch is heavily based on patches by Richard Zhu.
> 
> [bhelgaas: factor out refclk enable, fix adjacent typos in imx6q-pcie.txt]
> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
> Acked-by: Richard Zhu <Richard.Zhu@freescale.com>
> Acked-by: Lucas Stach <l.stach@pengutronix.de>
> ---
>  .../devicetree/bindings/pci/fsl,imx6q-pcie.txt     |  8 +++-
>  drivers/pci/host/pci-imx6.c                        | 53 ++++++++++++++++++++++
>  2 files changed, 59 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> index 6fbba53..6ee4439 100644
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> @@ -4,8 +4,8 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP
>  and thus inherits all the common properties defined in designware-pcie.txt.
>  
>  Required properties:
> -- compatible: "fsl,imx6q-pcie"
> -- reg: base addresse and length of the pcie controller
> +- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie"
> +- reg: base address and length of the PCIe controller
>  - interrupts: A list of interrupt outputs of the controller. Must contain an
>    entry for each entry in the interrupt-names property.
>  - interrupt-names: Must include the following entries:
> @@ -13,6 +13,10 @@ Required properties:
>  - clock-names: Must include the following additional entries:
>  	- "pcie_phy"
>  
> +Additional required properties for imx6sx-pcie:
> +- clock names: Must include the following additional entries:
> +	- "pcie_inbound_axi"
> +
>  Example:
>  
>  	pcie@0x01000000 {
> diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
> index 4e0e47f..fa3a544 100644
> --- a/drivers/pci/host/pci-imx6.c
> +++ b/drivers/pci/host/pci-imx6.c
> @@ -35,9 +35,11 @@ struct imx6_pcie {
>  	struct gpio_desc	*reset_gpio;
>  	struct clk		*pcie_bus;
>  	struct clk		*pcie_phy;
> +	struct clk		*pcie_inbound_axi;
>  	struct clk		*pcie;
>  	struct pcie_port	pp;
>  	struct regmap		*iomuxc_gpr;
> +	bool			is_imx6sx;
>  	void __iomem		*mem_base;
>  };
>  
> @@ -231,6 +233,17 @@ static int imx6_pcie_assert_core_reset(struct pcie_port *pp)
>  	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
>  	u32 val, gpr1, gpr12;
>  
> +	if (imx6_pcie->is_imx6sx) {
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
> +				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN,
> +				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN);
> +		/* Force PCIe PHY reset */
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
> +				   IMX6SX_GPR5_PCIE_BTNRST_RESET,
> +				   IMX6SX_GPR5_PCIE_BTNRST_RESET);
> +		return 0;
> +	}
> +
>  	/*
>  	 * If the bootloader already enabled the link we need some special
>  	 * handling to get the core back into a state where it is safe to
> @@ -266,6 +279,21 @@ static int imx6_pcie_assert_core_reset(struct pcie_port *pp)
>  
>  static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
>  {
> +	struct pcie_port *pp = &imx6_pcie->pp;
> +	int ret;
> +
> +	if (imx6_pcie->is_imx6sx) {
> +		ret = clk_prepare_enable(imx6_pcie->pcie_inbound_axi);
> +		if (ret) {
> +			dev_err(pp->dev, "unable to enable pcie_axi clock\n");
> +			return ret;
> +		}
> +
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
> +				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN, 0);
> +		return ret;
> +	}
> +
>  	/* power up core phy and enable ref clock */
>  	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
>  			IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
> @@ -319,6 +347,11 @@ static int imx6_pcie_deassert_core_reset(struct pcie_port *pp)
>  		msleep(100);
>  		gpiod_set_value_cansleep(imx6_pcie->reset_gpio, 1);
>  	}
> +
> +	if (imx6_pcie->is_imx6sx)
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
> +				   IMX6SX_GPR5_PCIE_BTNRST_RESET, 0);
> +
>  	return 0;
>  
>  err_ref_clk:
> @@ -336,6 +369,12 @@ static void imx6_pcie_init_phy(struct pcie_port *pp)
>  {
>  	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
>  
> +	if (imx6_pcie->is_imx6sx) {
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
> +				   IMX6SX_GPR12_PCIE_RX_EQ_MASK,
> +				   IMX6SX_GPR12_PCIE_RX_EQ_2);
> +	}
> +
>  	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
>  			IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
>  
> @@ -554,6 +593,9 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
>  	pp = &imx6_pcie->pp;
>  	pp->dev = &pdev->dev;
>  
> +	imx6_pcie->is_imx6sx = of_device_is_compatible(pp->dev->of_node,
> +						       "fsl,imx6sx-pcie");
> +
>  	/* Added for PCI abort handling */
>  	hook_fault_code(16 + 6, imx6q_pcie_abort_handler, SIGBUS, 0,
>  		"imprecise external abort");
> @@ -589,6 +631,16 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
>  		return PTR_ERR(imx6_pcie->pcie);
>  	}
>  
> +	if (imx6_pcie->is_imx6sx) {
> +		imx6_pcie->pcie_inbound_axi = devm_clk_get(&pdev->dev,
> +							   "pcie_inbound_axi");
> +		if (IS_ERR(imx6_pcie->pcie_inbound_axi)) {
> +			dev_err(&pdev->dev,
> +				"pcie_incbound_axi clock missing or invalid\n");
> +			return PTR_ERR(imx6_pcie->pcie_inbound_axi);
> +		}
> +	}
> +
>  	/* Grab GPR config register range */
>  	imx6_pcie->iomuxc_gpr =
>  		 syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
> @@ -615,6 +667,7 @@ static void imx6_pcie_shutdown(struct platform_device *pdev)
>  
>  static const struct of_device_id imx6_pcie_of_match[] = {
>  	{ .compatible = "fsl,imx6q-pcie", },
> +	{ .compatible = "fsl,imx6sx-pcie", },
>  	{},
>  };
>  MODULE_DEVICE_TABLE(of, imx6_pcie_of_match);



--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Bjorn Helgaas April 5, 2016, 9:56 p.m. UTC | #2
On Mon, Mar 14, 2016 at 12:31:10AM +0100, Christoph Fritz wrote:
> Add initial PCIe support for the imx6 SoC derivate imx6sx.  PCI MSI support
> is untested as the necessary suspend/resume quirk is not included in this
> patch.
> 
> This patch is heavily based on patches by Richard Zhu.
> 
> [bhelgaas: factor out refclk enable, fix adjacent typos in imx6q-pcie.txt]
> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
> Acked-by: Richard Zhu <Richard.Zhu@freescale.com>
> Acked-by: Lucas Stach <l.stach@pengutronix.de>

Applied to pci/host-imx6 for v4.7, thanks!

> ---
>  .../devicetree/bindings/pci/fsl,imx6q-pcie.txt     |  8 +++-
>  drivers/pci/host/pci-imx6.c                        | 53 ++++++++++++++++++++++
>  2 files changed, 59 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> index 6fbba53..6ee4439 100644
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> @@ -4,8 +4,8 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP
>  and thus inherits all the common properties defined in designware-pcie.txt.
>  
>  Required properties:
> -- compatible: "fsl,imx6q-pcie"
> -- reg: base addresse and length of the pcie controller
> +- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie"
> +- reg: base address and length of the PCIe controller
>  - interrupts: A list of interrupt outputs of the controller. Must contain an
>    entry for each entry in the interrupt-names property.
>  - interrupt-names: Must include the following entries:
> @@ -13,6 +13,10 @@ Required properties:
>  - clock-names: Must include the following additional entries:
>  	- "pcie_phy"
>  
> +Additional required properties for imx6sx-pcie:
> +- clock names: Must include the following additional entries:
> +	- "pcie_inbound_axi"
> +
>  Example:
>  
>  	pcie@0x01000000 {
> diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
> index 4e0e47f..fa3a544 100644
> --- a/drivers/pci/host/pci-imx6.c
> +++ b/drivers/pci/host/pci-imx6.c
> @@ -35,9 +35,11 @@ struct imx6_pcie {
>  	struct gpio_desc	*reset_gpio;
>  	struct clk		*pcie_bus;
>  	struct clk		*pcie_phy;
> +	struct clk		*pcie_inbound_axi;
>  	struct clk		*pcie;
>  	struct pcie_port	pp;
>  	struct regmap		*iomuxc_gpr;
> +	bool			is_imx6sx;
>  	void __iomem		*mem_base;
>  };
>  
> @@ -231,6 +233,17 @@ static int imx6_pcie_assert_core_reset(struct pcie_port *pp)
>  	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
>  	u32 val, gpr1, gpr12;
>  
> +	if (imx6_pcie->is_imx6sx) {
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
> +				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN,
> +				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN);
> +		/* Force PCIe PHY reset */
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
> +				   IMX6SX_GPR5_PCIE_BTNRST_RESET,
> +				   IMX6SX_GPR5_PCIE_BTNRST_RESET);
> +		return 0;
> +	}
> +
>  	/*
>  	 * If the bootloader already enabled the link we need some special
>  	 * handling to get the core back into a state where it is safe to
> @@ -266,6 +279,21 @@ static int imx6_pcie_assert_core_reset(struct pcie_port *pp)
>  
>  static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
>  {
> +	struct pcie_port *pp = &imx6_pcie->pp;
> +	int ret;
> +
> +	if (imx6_pcie->is_imx6sx) {
> +		ret = clk_prepare_enable(imx6_pcie->pcie_inbound_axi);
> +		if (ret) {
> +			dev_err(pp->dev, "unable to enable pcie_axi clock\n");
> +			return ret;
> +		}
> +
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
> +				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN, 0);
> +		return ret;
> +	}
> +
>  	/* power up core phy and enable ref clock */
>  	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
>  			IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
> @@ -319,6 +347,11 @@ static int imx6_pcie_deassert_core_reset(struct pcie_port *pp)
>  		msleep(100);
>  		gpiod_set_value_cansleep(imx6_pcie->reset_gpio, 1);
>  	}
> +
> +	if (imx6_pcie->is_imx6sx)
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
> +				   IMX6SX_GPR5_PCIE_BTNRST_RESET, 0);
> +
>  	return 0;
>  
>  err_ref_clk:
> @@ -336,6 +369,12 @@ static void imx6_pcie_init_phy(struct pcie_port *pp)
>  {
>  	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
>  
> +	if (imx6_pcie->is_imx6sx) {
> +		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
> +				   IMX6SX_GPR12_PCIE_RX_EQ_MASK,
> +				   IMX6SX_GPR12_PCIE_RX_EQ_2);
> +	}
> +
>  	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
>  			IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
>  
> @@ -554,6 +593,9 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
>  	pp = &imx6_pcie->pp;
>  	pp->dev = &pdev->dev;
>  
> +	imx6_pcie->is_imx6sx = of_device_is_compatible(pp->dev->of_node,
> +						       "fsl,imx6sx-pcie");
> +
>  	/* Added for PCI abort handling */
>  	hook_fault_code(16 + 6, imx6q_pcie_abort_handler, SIGBUS, 0,
>  		"imprecise external abort");
> @@ -589,6 +631,16 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
>  		return PTR_ERR(imx6_pcie->pcie);
>  	}
>  
> +	if (imx6_pcie->is_imx6sx) {
> +		imx6_pcie->pcie_inbound_axi = devm_clk_get(&pdev->dev,
> +							   "pcie_inbound_axi");
> +		if (IS_ERR(imx6_pcie->pcie_inbound_axi)) {
> +			dev_err(&pdev->dev,
> +				"pcie_incbound_axi clock missing or invalid\n");
> +			return PTR_ERR(imx6_pcie->pcie_inbound_axi);
> +		}
> +	}
> +
>  	/* Grab GPR config register range */
>  	imx6_pcie->iomuxc_gpr =
>  		 syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
> @@ -615,6 +667,7 @@ static void imx6_pcie_shutdown(struct platform_device *pdev)
>  
>  static const struct of_device_id imx6_pcie_of_match[] = {
>  	{ .compatible = "fsl,imx6q-pcie", },
> +	{ .compatible = "fsl,imx6sx-pcie", },
>  	{},
>  };
>  MODULE_DEVICE_TABLE(of, imx6_pcie_of_match);
> -- 
> 2.1.4
> 
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pci" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
index 6fbba53..6ee4439 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
@@ -4,8 +4,8 @@  This PCIe host controller is based on the Synopsis Designware PCIe IP
 and thus inherits all the common properties defined in designware-pcie.txt.
 
 Required properties:
-- compatible: "fsl,imx6q-pcie"
-- reg: base addresse and length of the pcie controller
+- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie"
+- reg: base address and length of the PCIe controller
 - interrupts: A list of interrupt outputs of the controller. Must contain an
   entry for each entry in the interrupt-names property.
 - interrupt-names: Must include the following entries:
@@ -13,6 +13,10 @@  Required properties:
 - clock-names: Must include the following additional entries:
 	- "pcie_phy"
 
+Additional required properties for imx6sx-pcie:
+- clock names: Must include the following additional entries:
+	- "pcie_inbound_axi"
+
 Example:
 
 	pcie@0x01000000 {
diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
index 4e0e47f..fa3a544 100644
--- a/drivers/pci/host/pci-imx6.c
+++ b/drivers/pci/host/pci-imx6.c
@@ -35,9 +35,11 @@  struct imx6_pcie {
 	struct gpio_desc	*reset_gpio;
 	struct clk		*pcie_bus;
 	struct clk		*pcie_phy;
+	struct clk		*pcie_inbound_axi;
 	struct clk		*pcie;
 	struct pcie_port	pp;
 	struct regmap		*iomuxc_gpr;
+	bool			is_imx6sx;
 	void __iomem		*mem_base;
 };
 
@@ -231,6 +233,17 @@  static int imx6_pcie_assert_core_reset(struct pcie_port *pp)
 	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
 	u32 val, gpr1, gpr12;
 
+	if (imx6_pcie->is_imx6sx) {
+		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN,
+				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN);
+		/* Force PCIe PHY reset */
+		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
+				   IMX6SX_GPR5_PCIE_BTNRST_RESET,
+				   IMX6SX_GPR5_PCIE_BTNRST_RESET);
+		return 0;
+	}
+
 	/*
 	 * If the bootloader already enabled the link we need some special
 	 * handling to get the core back into a state where it is safe to
@@ -266,6 +279,21 @@  static int imx6_pcie_assert_core_reset(struct pcie_port *pp)
 
 static int imx6_pcie_enable_ref_clk(struct imx6_pcie *imx6_pcie)
 {
+	struct pcie_port *pp = &imx6_pcie->pp;
+	int ret;
+
+	if (imx6_pcie->is_imx6sx) {
+		ret = clk_prepare_enable(imx6_pcie->pcie_inbound_axi);
+		if (ret) {
+			dev_err(pp->dev, "unable to enable pcie_axi clock\n");
+			return ret;
+		}
+
+		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+				   IMX6SX_GPR12_PCIE_TEST_POWERDOWN, 0);
+		return ret;
+	}
+
 	/* power up core phy and enable ref clock */
 	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
 			IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
@@ -319,6 +347,11 @@  static int imx6_pcie_deassert_core_reset(struct pcie_port *pp)
 		msleep(100);
 		gpiod_set_value_cansleep(imx6_pcie->reset_gpio, 1);
 	}
+
+	if (imx6_pcie->is_imx6sx)
+		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
+				   IMX6SX_GPR5_PCIE_BTNRST_RESET, 0);
+
 	return 0;
 
 err_ref_clk:
@@ -336,6 +369,12 @@  static void imx6_pcie_init_phy(struct pcie_port *pp)
 {
 	struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
 
+	if (imx6_pcie->is_imx6sx) {
+		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+				   IMX6SX_GPR12_PCIE_RX_EQ_MASK,
+				   IMX6SX_GPR12_PCIE_RX_EQ_2);
+	}
+
 	regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
 			IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
 
@@ -554,6 +593,9 @@  static int __init imx6_pcie_probe(struct platform_device *pdev)
 	pp = &imx6_pcie->pp;
 	pp->dev = &pdev->dev;
 
+	imx6_pcie->is_imx6sx = of_device_is_compatible(pp->dev->of_node,
+						       "fsl,imx6sx-pcie");
+
 	/* Added for PCI abort handling */
 	hook_fault_code(16 + 6, imx6q_pcie_abort_handler, SIGBUS, 0,
 		"imprecise external abort");
@@ -589,6 +631,16 @@  static int __init imx6_pcie_probe(struct platform_device *pdev)
 		return PTR_ERR(imx6_pcie->pcie);
 	}
 
+	if (imx6_pcie->is_imx6sx) {
+		imx6_pcie->pcie_inbound_axi = devm_clk_get(&pdev->dev,
+							   "pcie_inbound_axi");
+		if (IS_ERR(imx6_pcie->pcie_inbound_axi)) {
+			dev_err(&pdev->dev,
+				"pcie_incbound_axi clock missing or invalid\n");
+			return PTR_ERR(imx6_pcie->pcie_inbound_axi);
+		}
+	}
+
 	/* Grab GPR config register range */
 	imx6_pcie->iomuxc_gpr =
 		 syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
@@ -615,6 +667,7 @@  static void imx6_pcie_shutdown(struct platform_device *pdev)
 
 static const struct of_device_id imx6_pcie_of_match[] = {
 	{ .compatible = "fsl,imx6q-pcie", },
+	{ .compatible = "fsl,imx6sx-pcie", },
 	{},
 };
 MODULE_DEVICE_TABLE(of, imx6_pcie_of_match);