| Message ID | 1473246412-24616-1-git-send-email-srinivas.kandagatla@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Delegated to: | Bjorn Helgaas |
| Headers | show |
On 07/09/16 12:06, Srinivas Kandagatla wrote: > This patch adds support to msm8996/apq8096 pcie, MSM8996 supports > Gen 1/2, One lane, 3 pcie root-complex with support to MSI and > legacy interrupts and it conforms to PCI Express Base 2.1 specification. > > This patch adds post_init callback to qcom_pcie_ops, as this is pcie > pipe clocks and smmu configuration are only setup after the phy is > powered on. It also adds ltssm_enable callback as it is very much > different to other supported SOCs in the driver. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > --- > > I tested this patch along with phy driver patch on DB820c based on > APQ8096 on port A and port B using sata and ethernet controllers. > > Thanks > srini > > .../devicetree/bindings/pci/qcom,pcie.txt | 88 +++++++- > drivers/pci/host/pcie-qcom.c | 237 ++++++++++++++++++++- > 2 files changed, 318 insertions(+), 7 deletions(-) > > diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt > index 4059a6f..1ddfcb4 100644 > --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt > +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt > @@ -92,6 +92,18 @@ > - "aux" Auxiliary (AUX) clock > - "bus_master" Master AXI clock > - "bus_slave" Slave AXI clock > + > +- clock-names: > + Usage: required for msm8996/apq8096 > + Value type: <stringlist> > + Definition: Should contain the following entries > + - "aux" Auxiliary (AUX) clock > + - "bus_master" Master AXI clock > + - "bus_slave" Slave AXI clock > + - "pipe" Pipe Clock driving internal logic. > + - "cfg" Configuration clk. > + - "snoc_axi" SNOC AXI clk > + - "cnoc_ahb" CNOC AHB clk > - resets: > Usage: required > Value type: <prop-encoded-array> > @@ -114,8 +126,15 @@ > Definition: Should contain the following entries > - "core" Core reset > > +- iommus: > + Usage: required for msm8996/apq8096 > + Value type: <prop-encoded-array> > + Definition: Should point to the respective IOMMU block with master port > + as argument, see Documentation/devicetree/bindings/iommu/ > + mediatek,iommu.txt for details. Qualcomm have cross-licensed the M4U!? :P In seriousness, though, it seems a bit odd to list "iommus" as a required property - unless the IOMMU is actually an integral part of the PCIe root complex being described (in which case it wants its own binding documenting as well), then the relationship is merely a circumstance of integration of those particular SoCs. > + > - power-domains: > - Usage: required for apq8084 > + Usage: required for apq8084 and msm8996/apq8096 > Value type: <prop-encoded-array> > Definition: A phandle and power domain specifier pair to the > power domain which is responsible for collapsing > @@ -137,6 +156,11 @@ > Definition: A phandle to the analog power supply for IC which generates > reference clock > > +- vdda_1p8-supply: > + Usage: required for msm8996/apq8096 > + Value type: <phandle> > + Definition: A phandle to the analog power supply for PCIE_1P8 > + > - phys: > Usage: required for apq8084 > Value type: <phandle> > @@ -231,3 +255,65 @@ > pinctrl-0 = <&pcie0_pins_default>; > pinctrl-names = "default"; > }; > + > +* Example for apq8096: > + pcie1: qcom,pcie@00608000 { > + compatible = "qcom,pcie-msm8996", "snps,dw-pcie"; > + power-domains = <&gcc PCIE1_GDSC>; > + bus-range = <0x00 0xff>; > + num-lanes = <1>; > + > + status = "disabled"; > + > + reg = <0x00608000 0x2000>, > + <0x0d000000 0xf1d>, > + <0x0d000f20 0xa8>, > + <0x0d100000 0x100000>; > + > + reg-names = "parf", "dbi", "elbi","config"; > + > + phys = <&pcie_phy 1>; > + phy-names = "pciephy"; > + > + #address-cells = <3>; > + #size-cells = <2>; > + ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>, > + <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>; > + > + interrupts = <GIC_SPI 413 IRQ_TYPE_NONE>; > + interrupt-names = "msi"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 0x7>; > + interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ > + <0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ > + <0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ > + <0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>; > + pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>; > + > + > + vreg-1.8-supply = <&pm8994_l12>; > + vreg-0.9-supply = <&pm8994_l28>; > + iommus = <&anoc0_smmu>; Furthermore, the exact meaning of "iommus" is defined by the relevant IOMMU's binding itself - at face value here, you're missing the LARB port number :P - but more generally a bare phandle with no arguments for something as busy as a root complex smells a bit off. > + > + linux,pci-domain = <1>; > + > + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, > + <&gcc GCC_PCIE_1_AUX_CLK>, > + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, > + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, > + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, > + <&gcc GCC_AGGRE0_SNOC_AXI_CLK>, > + <&gcc GCC_AGGRE0_CNOC_AHB_CLK>; > + > + clock-names = "pipe", > + "aux", > + "cfg", > + "bus_master", > + "bus_slave", > + "snoc_axi", > + "cnoc_ahb"; > + > + }; > diff --git a/drivers/pci/host/pcie-qcom.c b/drivers/pci/host/pcie-qcom.c > index f2f90c5..7748c11 100644 > --- a/drivers/pci/host/pcie-qcom.c > +++ b/drivers/pci/host/pcie-qcom.c [...] > +static int qcom_pcie_post_init_msm8996(struct qcom_pcie *pcie) > +{ > + struct qcom_pcie_resources_msm8996 *res = &pcie->res.msm8996; > + struct device *dev = pcie->dev; > + int ret; > + > + ret = clk_prepare_enable(res->pipe_clk); > + if (ret) { > + dev_err(dev, "cannot prepare/enable pipe clock\n"); > + return ret; > + } > + /* SMMU specific registers */ > + writel(0, pcie->parf + PCIE20_PARF_BDF_TRANSLATE_CFG); > + writel(0, pcie->parf + PCIE20_PARF_SID_OFFSET); Ah, so it's another of these RID->SID lookup-table-type things. That would be more appropriately described with "iommu-map"[1], particularly if you want things to actually work as expected[2]. There is of course a fun circular dependency there in that the DT becomes more of a promise than an actual description of the hardware state, since the latter doesn't necessarily exist until the driver programs it here. It might ultimately be cleaner to have the firmware program this and repaint the DT accordingly, so that things do look fixed from Linux's perspective. Robin. [1]:http://www.mail-archive.com/iommu@lists.linux-foundation.org/msg14165.html [2]:http://www.mail-archive.com/iommu@lists.linux-foundation.org/msg14162.html -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Thanks for the comments, On 07/09/16 12:57, Robin Murphy wrote: > On 07/09/16 12:06, Srinivas Kandagatla wrote: >> This patch adds support to msm8996/apq8096 pcie, MSM8996 supports >> Gen 1/2, One lane, 3 pcie root-complex with support to MSI and >> legacy interrupts and it conforms to PCI Express Base 2.1 specification. >> >> This patch adds post_init callback to qcom_pcie_ops, as this is pcie >> pipe clocks and smmu configuration are only setup after the phy is >> powered on. It also adds ltssm_enable callback as it is very much >> different to other supported SOCs in the driver. >> >> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> >> --- >> >> I tested this patch along with phy driver patch on DB820c based on >> APQ8096 on port A and port B using sata and ethernet controllers. >> >> Thanks >> srini >> >> .../devicetree/bindings/pci/qcom,pcie.txt | 88 +++++++- >> drivers/pci/host/pcie-qcom.c | 237 ++++++++++++++++++++- >> 2 files changed, 318 insertions(+), 7 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt >> index 4059a6f..1ddfcb4 100644 >> --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt >> +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt >> @@ -92,6 +92,18 @@ >> - "aux" Auxiliary (AUX) clock >> - "bus_master" Master AXI clock >> - "bus_slave" Slave AXI clock >> + >> +- clock-names: >> + Usage: required for msm8996/apq8096 >> + Value type: <stringlist> >> + Definition: Should contain the following entries >> + - "aux" Auxiliary (AUX) clock >> + - "bus_master" Master AXI clock >> + - "bus_slave" Slave AXI clock >> + - "pipe" Pipe Clock driving internal logic. >> + - "cfg" Configuration clk. >> + - "snoc_axi" SNOC AXI clk >> + - "cnoc_ahb" CNOC AHB clk >> - resets: >> Usage: required >> Value type: <prop-encoded-array> >> @@ -114,8 +126,15 @@ >> Definition: Should contain the following entries >> - "core" Core reset >> >> +- iommus: >> + Usage: required for msm8996/apq8096 >> + Value type: <prop-encoded-array> >> + Definition: Should point to the respective IOMMU block with master port >> + as argument, see Documentation/devicetree/bindings/iommu/ >> + mediatek,iommu.txt for details. > > Qualcomm have cross-licensed the M4U!? :P Oops...Copy paste error!! This is supposed to be Documentation/devicetree/bindings/iommu/arm,smmu.txt > > In seriousness, though, it seems a bit odd to list "iommus" as a > required property - unless the IOMMU is actually an integral part of the > PCIe root complex being described (in which case it wants its own > binding documenting as well), then the relationship is merely a > circumstance of integration of those particular SoCs. > >> + >> - power-domains: >> - Usage: required for apq8084 >> + Usage: required for apq8084 and msm8996/apq8096 >> Value type: <prop-encoded-array> >> Definition: A phandle and power domain specifier pair to the >> power domain which is responsible for collapsing >> @@ -137,6 +156,11 @@ >> Definition: A phandle to the analog power supply for IC which generates >> reference clock >> >> +- vdda_1p8-supply: >> + Usage: required for msm8996/apq8096 >> + Value type: <phandle> >> + Definition: A phandle to the analog power supply for PCIE_1P8 >> + >> - phys: >> Usage: required for apq8084 >> Value type: <phandle> >> @@ -231,3 +255,65 @@ >> pinctrl-0 = <&pcie0_pins_default>; >> pinctrl-names = "default"; >> }; >> + >> +* Example for apq8096: >> + pcie1: qcom,pcie@00608000 { >> + compatible = "qcom,pcie-msm8996", "snps,dw-pcie"; >> + power-domains = <&gcc PCIE1_GDSC>; >> + bus-range = <0x00 0xff>; >> + num-lanes = <1>; >> + >> + status = "disabled"; >> + >> + reg = <0x00608000 0x2000>, >> + <0x0d000000 0xf1d>, >> + <0x0d000f20 0xa8>, >> + <0x0d100000 0x100000>; >> + >> + reg-names = "parf", "dbi", "elbi","config"; >> + >> + phys = <&pcie_phy 1>; >> + phy-names = "pciephy"; >> + >> + #address-cells = <3>; >> + #size-cells = <2>; >> + ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>, >> + <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>; >> + >> + interrupts = <GIC_SPI 413 IRQ_TYPE_NONE>; >> + interrupt-names = "msi"; >> + #interrupt-cells = <1>; >> + interrupt-map-mask = <0 0 0 0x7>; >> + interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ >> + <0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ >> + <0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ >> + <0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ >> + >> + pinctrl-names = "default", "sleep"; >> + pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>; >> + pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>; >> + >> + >> + vreg-1.8-supply = <&pm8994_l12>; >> + vreg-0.9-supply = <&pm8994_l28>; >> + iommus = <&anoc0_smmu>; > > Furthermore, the exact meaning of "iommus" is defined by the relevant > IOMMU's binding itself - at face value here, you're missing the LARB > port number :P - but more generally a bare phandle with no arguments for > something as busy as a root complex smells a bit off. This is arm smmu v2, the smmu instance in this case had #iommu-cells = <0>, so no arguments were not used. However I will dig in more details on why this smmu instance does not accept arguments/stream-ids. > >> + >> + linux,pci-domain = <1>; >> + >> + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, >> + <&gcc GCC_PCIE_1_AUX_CLK>, >> + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, >> + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, >> + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, >> + <&gcc GCC_AGGRE0_SNOC_AXI_CLK>, >> + <&gcc GCC_AGGRE0_CNOC_AHB_CLK>; >> + >> + clock-names = "pipe", >> + "aux", >> + "cfg", >> + "bus_master", >> + "bus_slave", >> + "snoc_axi", >> + "cnoc_ahb"; >> + >> + }; >> diff --git a/drivers/pci/host/pcie-qcom.c b/drivers/pci/host/pcie-qcom.c >> index f2f90c5..7748c11 100644 >> --- a/drivers/pci/host/pcie-qcom.c >> +++ b/drivers/pci/host/pcie-qcom.c > [...] >> +static int qcom_pcie_post_init_msm8996(struct qcom_pcie *pcie) >> +{ >> + struct qcom_pcie_resources_msm8996 *res = &pcie->res.msm8996; >> + struct device *dev = pcie->dev; >> + int ret; >> + >> + ret = clk_prepare_enable(res->pipe_clk); >> + if (ret) { >> + dev_err(dev, "cannot prepare/enable pipe clock\n"); >> + return ret; >> + } >> + /* SMMU specific registers */ >> + writel(0, pcie->parf + PCIE20_PARF_BDF_TRANSLATE_CFG); >> + writel(0, pcie->parf + PCIE20_PARF_SID_OFFSET); > > Ah, so it's another of these RID->SID lookup-table-type things. That > would be more appropriately described with "iommu-map"[1], particularly > if you want things to actually work as expected[2]. There is of course a > fun circular dependency there in that the DT becomes more of a promise > than an actual description of the hardware state, since the latter > doesn't necessarily exist until the driver programs it here. It might > ultimately be cleaner to have the firmware program this and repaint the > DT accordingly, so that things do look fixed from Linux's perspective. Thanks for the hints, I will read thru the thread and give it a try. --srini > > Robin. > > [1]:http://www.mail-archive.com/iommu@lists.linux-foundation.org/msg14165.html > [2]:http://www.mail-archive.com/iommu@lists.linux-foundation.org/msg14162.html > -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, Sep 07, 2016 at 12:06:52PM +0100, Srinivas Kandagatla wrote: > This patch adds support to msm8996/apq8096 pcie, MSM8996 supports > Gen 1/2, One lane, 3 pcie root-complex with support to MSI and > legacy interrupts and it conforms to PCI Express Base 2.1 specification. > > This patch adds post_init callback to qcom_pcie_ops, as this is pcie > pipe clocks and smmu configuration are only setup after the phy is > powered on. It also adds ltssm_enable callback as it is very much > different to other supported SOCs in the driver. > > Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> > --- > > I tested this patch along with phy driver patch on DB820c based on > APQ8096 on port A and port B using sata and ethernet controllers. > > Thanks > srini > > .../devicetree/bindings/pci/qcom,pcie.txt | 88 +++++++- > drivers/pci/host/pcie-qcom.c | 237 ++++++++++++++++++++- > 2 files changed, 318 insertions(+), 7 deletions(-) > > diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt > index 4059a6f..1ddfcb4 100644 > --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt > +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt > @@ -92,6 +92,18 @@ > - "aux" Auxiliary (AUX) clock > - "bus_master" Master AXI clock > - "bus_slave" Slave AXI clock > + > +- clock-names: > + Usage: required for msm8996/apq8096 > + Value type: <stringlist> > + Definition: Should contain the following entries > + - "aux" Auxiliary (AUX) clock > + - "bus_master" Master AXI clock > + - "bus_slave" Slave AXI clock > + - "pipe" Pipe Clock driving internal logic. > + - "cfg" Configuration clk. > + - "snoc_axi" SNOC AXI clk > + - "cnoc_ahb" CNOC AHB clk > - resets: > Usage: required > Value type: <prop-encoded-array> > @@ -114,8 +126,15 @@ > Definition: Should contain the following entries > - "core" Core reset > > +- iommus: > + Usage: required for msm8996/apq8096 > + Value type: <prop-encoded-array> > + Definition: Should point to the respective IOMMU block with master port > + as argument, see Documentation/devicetree/bindings/iommu/ > + mediatek,iommu.txt for details. > + > - power-domains: > - Usage: required for apq8084 > + Usage: required for apq8084 and msm8996/apq8096 > Value type: <prop-encoded-array> > Definition: A phandle and power domain specifier pair to the > power domain which is responsible for collapsing > @@ -137,6 +156,11 @@ > Definition: A phandle to the analog power supply for IC which generates > reference clock > > +- vdda_1p8-supply: Don't use '_' in property names. > + Usage: required for msm8996/apq8096 > + Value type: <phandle> > + Definition: A phandle to the analog power supply for PCIE_1P8 > + > - phys: > Usage: required for apq8084 > Value type: <phandle> > @@ -231,3 +255,65 @@ > pinctrl-0 = <&pcie0_pins_default>; > pinctrl-names = "default"; > }; > + > +* Example for apq8096: > + pcie1: qcom,pcie@00608000 { pcie@... > + compatible = "qcom,pcie-msm8996", "snps,dw-pcie"; > + power-domains = <&gcc PCIE1_GDSC>; > + bus-range = <0x00 0xff>; > + num-lanes = <1>; > + > + status = "disabled"; > + > + reg = <0x00608000 0x2000>, > + <0x0d000000 0xf1d>, > + <0x0d000f20 0xa8>, > + <0x0d100000 0x100000>; > + > + reg-names = "parf", "dbi", "elbi","config"; > + > + phys = <&pcie_phy 1>; > + phy-names = "pciephy"; > + > + #address-cells = <3>; > + #size-cells = <2>; > + ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>, > + <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>; > + > + interrupts = <GIC_SPI 413 IRQ_TYPE_NONE>; > + interrupt-names = "msi"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 0x7>; > + interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ > + <0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ > + <0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ > + <0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ > + > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>; > + pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>; > + > + > + vreg-1.8-supply = <&pm8994_l12>; > + vreg-0.9-supply = <&pm8994_l28>; Doesn't match binding? > + iommus = <&anoc0_smmu>; > + > + linux,pci-domain = <1>; > + > + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, > + <&gcc GCC_PCIE_1_AUX_CLK>, > + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, > + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, > + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, > + <&gcc GCC_AGGRE0_SNOC_AXI_CLK>, > + <&gcc GCC_AGGRE0_CNOC_AHB_CLK>; > + > + clock-names = "pipe", > + "aux", > + "cfg", > + "bus_master", > + "bus_slave", > + "snoc_axi", > + "cnoc_ahb"; > + > + }; -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Thanks for the Review, On 16/09/16 15:17, Rob Herring wrote: > On Wed, Sep 07, 2016 at 12:06:52PM +0100, Srinivas Kandagatla wrote: > ... >> >> diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt >> index 4059a6f..1ddfcb4 100644 >> --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt >> +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt >> @@ -92,6 +92,18 @@ ... >> Definition: A phandle and power domain specifier pair to the >> power domain which is responsible for collapsing >> @@ -137,6 +156,11 @@ >> Definition: A phandle to the analog power supply for IC which generates >> reference clock >> >> +- vdda_1p8-supply: > > Don't use '_' in property names. Will fix it and example to match these properties in next version. > >> + Usage: required for msm8996/apq8096 >> + Value type: <phandle> >> + Definition: A phandle to the analog power supply for PCIE_1P8 >> + >> - phys: >> Usage: required for apq8084 >> Value type: <phandle> >> @@ -231,3 +255,65 @@ >> pinctrl-0 = <&pcie0_pins_default>; >> pinctrl-names = "default"; >> }; >> + >> +* Example for apq8096: >> + pcie1: qcom,pcie@00608000 { > > pcie@... Yep, will fix it in next version. > >> + compatible = "qcom,pcie-msm8996", "snps,dw-pcie"; >> + power-domains = <&gcc PCIE1_GDSC>; >> + bus-range = <0x00 0xff>; >> + num-lanes = <1>; >> + >> + status = "disabled"; >> + >> + reg = <0x00608000 0x2000>, >> + <0x0d000000 0xf1d>, >> + <0x0d000f20 0xa8>, >> + <0x0d100000 0x100000>; >> + -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt index 4059a6f..1ddfcb4 100644 --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -92,6 +92,18 @@ - "aux" Auxiliary (AUX) clock - "bus_master" Master AXI clock - "bus_slave" Slave AXI clock + +- clock-names: + Usage: required for msm8996/apq8096 + Value type: <stringlist> + Definition: Should contain the following entries + - "aux" Auxiliary (AUX) clock + - "bus_master" Master AXI clock + - "bus_slave" Slave AXI clock + - "pipe" Pipe Clock driving internal logic. + - "cfg" Configuration clk. + - "snoc_axi" SNOC AXI clk + - "cnoc_ahb" CNOC AHB clk - resets: Usage: required Value type: <prop-encoded-array> @@ -114,8 +126,15 @@ Definition: Should contain the following entries - "core" Core reset +- iommus: + Usage: required for msm8996/apq8096 + Value type: <prop-encoded-array> + Definition: Should point to the respective IOMMU block with master port + as argument, see Documentation/devicetree/bindings/iommu/ + mediatek,iommu.txt for details. + - power-domains: - Usage: required for apq8084 + Usage: required for apq8084 and msm8996/apq8096 Value type: <prop-encoded-array> Definition: A phandle and power domain specifier pair to the power domain which is responsible for collapsing @@ -137,6 +156,11 @@ Definition: A phandle to the analog power supply for IC which generates reference clock +- vdda_1p8-supply: + Usage: required for msm8996/apq8096 + Value type: <phandle> + Definition: A phandle to the analog power supply for PCIE_1P8 + - phys: Usage: required for apq8084 Value type: <phandle> @@ -231,3 +255,65 @@ pinctrl-0 = <&pcie0_pins_default>; pinctrl-names = "default"; }; + +* Example for apq8096: + pcie1: qcom,pcie@00608000 { + compatible = "qcom,pcie-msm8996", "snps,dw-pcie"; + power-domains = <&gcc PCIE1_GDSC>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + + status = "disabled"; + + reg = <0x00608000 0x2000>, + <0x0d000000 0xf1d>, + <0x0d000f20 0xa8>, + <0x0d100000 0x100000>; + + reg-names = "parf", "dbi", "elbi","config"; + + phys = <&pcie_phy 1>; + phy-names = "pciephy"; + + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>, + <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>; + + interrupts = <GIC_SPI 413 IRQ_TYPE_NONE>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>; + pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>; + + + vreg-1.8-supply = <&pm8994_l12>; + vreg-0.9-supply = <&pm8994_l28>; + iommus = <&anoc0_smmu>; + + linux,pci-domain = <1>; + + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, + <&gcc GCC_PCIE_1_AUX_CLK>, + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, + <&gcc GCC_AGGRE0_SNOC_AXI_CLK>, + <&gcc GCC_AGGRE0_CNOC_AHB_CLK>; + + clock-names = "pipe", + "aux", + "cfg", + "bus_master", + "bus_slave", + "snoc_axi", + "cnoc_ahb"; + + }; diff --git a/drivers/pci/host/pcie-qcom.c b/drivers/pci/host/pcie-qcom.c index f2f90c5..7748c11 100644 --- a/drivers/pci/host/pcie-qcom.c +++ b/drivers/pci/host/pcie-qcom.c @@ -32,11 +32,19 @@ #include "pcie-designware.h" +#define PCIE20_PARF_DBI_BASE_ADDR 0x168 + +#define PCIE20_PARF_SYS_CTRL 0x00 #define PCIE20_PARF_PHY_CTRL 0x40 #define PCIE20_PARF_PHY_REFCLK 0x4C #define PCIE20_PARF_DBI_BASE_ADDR 0x168 #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE 0x16c +#define PCIE20_PARF_MHI_CLOCK_RESET_CTRL 0x174 #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT 0x178 +#define MSM8996_PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT 0x1A8 +#define PCIE20_PARF_LTSSM 0x1B0 +#define PCIE20_PARF_SID_OFFSET 0x234 +#define PCIE20_PARF_BDF_TRANSLATE_CFG 0x24C #define PCIE20_ELBI_SYS_CTRL 0x04 #define PCIE20_ELBI_SYS_CTRL_LT_ENABLE BIT(0) @@ -68,9 +76,22 @@ struct qcom_pcie_resources_v1 { struct regulator *vdda; }; +struct qcom_pcie_resources_msm8996 { + struct clk *aux_clk; + struct clk *master_clk; + struct clk *slave_clk; + struct clk *cfg_clk; + struct clk *axi_clk; + struct clk *ahb_clk; + struct clk *pipe_clk; + struct regulator *vdda_1p8; + struct regulator *vdda; +}; + union qcom_pcie_resources { struct qcom_pcie_resources_v0 v0; struct qcom_pcie_resources_v1 v1; + struct qcom_pcie_resources_msm8996 msm8996; }; struct qcom_pcie; @@ -78,7 +99,9 @@ struct qcom_pcie; struct qcom_pcie_ops { int (*get_resources)(struct qcom_pcie *pcie); int (*init)(struct qcom_pcie *pcie); + int (*post_init)(struct qcom_pcie *pcie); void (*deinit)(struct qcom_pcie *pcie); + void (*ltssm_enable)(struct qcom_pcie *pcie); }; struct qcom_pcie { @@ -114,17 +137,33 @@ static irqreturn_t qcom_pcie_msi_irq_handler(int irq, void *arg) return dw_handle_msi_irq(pp); } -static int qcom_pcie_establish_link(struct qcom_pcie *pcie) +static void qcom_pcie_v0_v1_ltssm_enable(struct qcom_pcie *pcie) { u32 val; - - if (dw_pcie_link_up(&pcie->pp)) - return 0; - /* enable link training */ val = readl(pcie->elbi + PCIE20_ELBI_SYS_CTRL); val |= PCIE20_ELBI_SYS_CTRL_LT_ENABLE; writel(val, pcie->elbi + PCIE20_ELBI_SYS_CTRL); +} + +static void qcom_pcie_msm8996_ltssm_enable(struct qcom_pcie *pcie) +{ + u32 val; + /* enable link training */ + val = readl(pcie->parf + PCIE20_PARF_LTSSM); + val |= BIT(8); + writel(val, pcie->parf + PCIE20_PARF_LTSSM); +} + +static int qcom_pcie_establish_link(struct qcom_pcie *pcie) +{ + + if (dw_pcie_link_up(&pcie->pp)) + return 0; + + /* Enable Link Training state machine */ + if (pcie->ops->ltssm_enable) + pcie->ops->ltssm_enable(pcie); return dw_pcie_wait_for_link(&pcie->pp); } @@ -419,6 +458,164 @@ err_res: return ret; } +static int qcom_pcie_get_resources_msm8996(struct qcom_pcie *pcie) +{ + struct qcom_pcie_resources_msm8996 *res = &pcie->res.msm8996; + struct device *dev = pcie->dev; + + res->vdda_1p8 = devm_regulator_get(dev, "vdda_1p8"); + if (IS_ERR(res->vdda_1p8)) + return PTR_ERR(res->vdda_1p8); + + res->vdda = devm_regulator_get(dev, "vdda"); + if (IS_ERR(res->vdda)) + return PTR_ERR(res->vdda); + + res->axi_clk = devm_clk_get(dev, "snoc_axi"); + if (IS_ERR(res->axi_clk)) + return PTR_ERR(res->axi_clk); + + res->ahb_clk = devm_clk_get(dev, "cnoc_ahb"); + if (IS_ERR(res->ahb_clk)) + return PTR_ERR(res->ahb_clk); + + res->aux_clk = devm_clk_get(dev, "aux"); + if (IS_ERR(res->aux_clk)) + return PTR_ERR(res->aux_clk); + + res->cfg_clk = devm_clk_get(dev, "cfg"); + if (IS_ERR(res->cfg_clk)) + return PTR_ERR(res->cfg_clk); + + res->master_clk = devm_clk_get(dev, "bus_master"); + if (IS_ERR(res->master_clk)) + return PTR_ERR(res->master_clk); + + res->slave_clk = devm_clk_get(dev, "bus_slave"); + if (IS_ERR(res->slave_clk)) + return PTR_ERR(res->slave_clk); + + res->pipe_clk = devm_clk_get(dev, "pipe"); + if (IS_ERR(res->pipe_clk)) + return PTR_ERR(res->pipe_clk); + + return 0; +} + +static int qcom_pcie_init_msm8996(struct qcom_pcie *pcie) +{ + struct qcom_pcie_resources_msm8996 *res = &pcie->res.msm8996; + struct device *dev = pcie->dev; + u32 val; + int ret = 0; + + ret = regulator_enable(res->vdda_1p8); + if (ret) { + dev_err(dev, "cannot enable vdda_1p8 regulator\n"); + return ret; + } + + ret = regulator_enable(res->vdda); + if (ret) { + dev_err(dev, "cannot enable vdda regulator\n"); + goto err_vdda; + } + + ret = clk_prepare_enable(res->axi_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable axi clock\n"); + goto err_axi_clk; + } + + ret = clk_prepare_enable(res->ahb_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable ahb clock\n"); + goto err_ahb_clk; + } + + ret = clk_prepare_enable(res->aux_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable aux clock\n"); + goto err_aux_clk; + } + + ret = clk_prepare_enable(res->cfg_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable cfg clock\n"); + goto err_cfg_clk; + } + + ret = clk_prepare_enable(res->master_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable master clock\n"); + goto err_master_clk; + } + + ret = clk_prepare_enable(res->slave_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable slave clock\n"); + goto err_slave_clk; + } + + /* enable PCIe clocks and resets */ + val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL); + val &= ~BIT(0); + writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL); + + /* change DBI base address */ + writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR); + + /* MAC PHY_POWERDOWN MUX DISABLE */ + val = readl(pcie->parf + PCIE20_PARF_SYS_CTRL); + val &= ~BIT(29); + writel(val, pcie->parf + PCIE20_PARF_SYS_CTRL); + + val = readl(pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL); + val |= BIT(4); + writel(val, pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL); + + val = readl(pcie->parf + MSM8996_PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT); + val |= BIT(31); + writel(val, pcie->parf + MSM8996_PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT); + + return 0; + +err_slave_clk: + clk_disable_unprepare(res->master_clk); +err_master_clk: + clk_disable_unprepare(res->cfg_clk); +err_cfg_clk: + clk_disable_unprepare(res->aux_clk); +err_aux_clk: + clk_disable_unprepare(res->ahb_clk); +err_ahb_clk: + clk_disable_unprepare(res->axi_clk); +err_axi_clk: + regulator_disable(res->vdda); +err_vdda: + regulator_disable(res->vdda_1p8); + + return ret; +} + +static int qcom_pcie_post_init_msm8996(struct qcom_pcie *pcie) +{ + struct qcom_pcie_resources_msm8996 *res = &pcie->res.msm8996; + struct device *dev = pcie->dev; + int ret; + + ret = clk_prepare_enable(res->pipe_clk); + if (ret) { + dev_err(dev, "cannot prepare/enable pipe clock\n"); + return ret; + } + /* SMMU specific registers */ + writel(0, pcie->parf + PCIE20_PARF_BDF_TRANSLATE_CFG); + writel(0, pcie->parf + PCIE20_PARF_SID_OFFSET); + + return 0; +} + static int qcom_pcie_link_up(struct pcie_port *pp) { struct qcom_pcie *pcie = to_qcom_pcie(pp); @@ -427,6 +624,21 @@ static int qcom_pcie_link_up(struct pcie_port *pp) return !!(val & PCI_EXP_LNKSTA_DLLLA); } +static void qcom_pcie_deinit_msm8996(struct qcom_pcie *pcie) +{ + struct qcom_pcie_resources_msm8996 *res = &pcie->res.msm8996; + + clk_disable_unprepare(res->slave_clk); + clk_disable_unprepare(res->master_clk); + clk_disable_unprepare(res->cfg_clk); + clk_disable_unprepare(res->aux_clk); + clk_disable_unprepare(res->ahb_clk); + clk_disable_unprepare(res->axi_clk); + clk_disable_unprepare(res->pipe_clk); + regulator_disable(res->vdda); + regulator_disable(res->vdda_1p8); +} + static void qcom_pcie_host_init(struct pcie_port *pp) { struct qcom_pcie *pcie = to_qcom_pcie(pp); @@ -437,11 +649,13 @@ static void qcom_pcie_host_init(struct pcie_port *pp) ret = pcie->ops->init(pcie); if (ret) goto err_deinit; - ret = phy_power_on(pcie->phy); if (ret) goto err_deinit; + if (pcie->ops->post_init) + pcie->ops->post_init(pcie); + dw_pcie_setup_rc(pp); if (IS_ENABLED(CONFIG_PCI_MSI)) @@ -485,12 +699,22 @@ static const struct qcom_pcie_ops ops_v0 = { .get_resources = qcom_pcie_get_resources_v0, .init = qcom_pcie_init_v0, .deinit = qcom_pcie_deinit_v0, + .ltssm_enable = qcom_pcie_v0_v1_ltssm_enable, }; static const struct qcom_pcie_ops ops_v1 = { .get_resources = qcom_pcie_get_resources_v1, .init = qcom_pcie_init_v1, .deinit = qcom_pcie_deinit_v1, + .ltssm_enable = qcom_pcie_v0_v1_ltssm_enable, +}; + +static const struct qcom_pcie_ops ops_msm8996 = { + .get_resources = qcom_pcie_get_resources_msm8996, + .init = qcom_pcie_init_msm8996, + .post_init = qcom_pcie_post_init_msm8996, + .deinit = qcom_pcie_deinit_msm8996, + .ltssm_enable = qcom_pcie_msm8996_ltssm_enable, }; static int qcom_pcie_probe(struct platform_device *pdev) @@ -586,6 +810,7 @@ static const struct of_device_id qcom_pcie_match[] = { { .compatible = "qcom,pcie-ipq8064", .data = &ops_v0 }, { .compatible = "qcom,pcie-apq8064", .data = &ops_v0 }, { .compatible = "qcom,pcie-apq8084", .data = &ops_v1 }, + { .compatible = "qcom,pcie-msm8996", .data = &ops_msm8996 }, { } }; MODULE_DEVICE_TABLE(of, qcom_pcie_match);
This patch adds support to msm8996/apq8096 pcie, MSM8996 supports Gen 1/2, One lane, 3 pcie root-complex with support to MSI and legacy interrupts and it conforms to PCI Express Base 2.1 specification. This patch adds post_init callback to qcom_pcie_ops, as this is pcie pipe clocks and smmu configuration are only setup after the phy is powered on. It also adds ltssm_enable callback as it is very much different to other supported SOCs in the driver. Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> --- I tested this patch along with phy driver patch on DB820c based on APQ8096 on port A and port B using sata and ethernet controllers. Thanks srini .../devicetree/bindings/pci/qcom,pcie.txt | 88 +++++++- drivers/pci/host/pcie-qcom.c | 237 ++++++++++++++++++++- 2 files changed, 318 insertions(+), 7 deletions(-)