| Message ID | 160ee086771703c951c5522d997662aeac122a28.1704788539.git.ysato@users.sourceforge.jp (mailing list archive) |
|---|---|
| State | Not Applicable |
| Delegated to: | Krzysztof Wilczyński |
| Headers | show |
| Series | Device Tree support for SH7751 based board | expand |
Hi Yoshinori, thanks for your patch! On Tue, Jan 9, 2024 at 9:24 AM Yoshinori Sato <ysato@users.sourceforge.jp> wrote: > Renesas SH7751 PCI Controller json-schema. > > Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp> (...) > + renesas,bus-arbit-round-robin: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set DMA bus arbitration to round robin. > + > + pci-command-reg-fast-back-to-back: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI command register Fast Back-to-Back enable bit. > + > + pci-command-reg-serr: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI command register SERR# enable. > + > + pci-command-reg-wait-cycle-control: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI command register Wait cycle control bit. > + > + pci-command-reg-parity-error-response: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI Command register Parity error response bit. > + > + pci-command-reg-vga-snoop: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI Command register VGA palette snoop bit. > + > + pci-command-reg-write-invalidate: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI Command register Memory write and invaldate enable bit. > + > + pci-command-reg-special-cycle: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI Command register Special cycle bit. > + > + pci-command-reg-bus-master: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI Command register Bus master bit. > + > + pci-command-reg-memory-space: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI Command register Memory space bit. > + > + pci-command-reg-io-space: > + $ref: /schemas/types.yaml#/definitions/flag > + description: | > + Set for PCI Command register I/O space bit. Do you really need to configure all these things? It seems they are just set to default values anyway? Can't you just look at the compatible "renesas,sh7751-pci" and set it to the values you know are needed for that compatible? > + pci-bar: > + $ref: /schemas/types.yaml#/definitions/uint32-matrix > + description: Overwrite to PCI CONFIG Base Address Registers value. > + items: > + items: > + - description: BAR register number > + - description: BAR register value > + minItems: 1 > + maxItems: 6 Same with this, isn't this always the same (hardcoded) values for "renesas,sh7751-pci" if used? > + interrupt-map = <0x0000 0 0 1 &julianintc 5>, > + <0x0000 0 0 2 &julianintc 6>, > + <0x0000 0 0 3 &julianintc 7>, > + <0x0000 0 0 4 &julianintc 8>, > + <0x0800 0 0 1 &julianintc 6>, > + <0x0800 0 0 2 &julianintc 7>, > + <0x0800 0 0 3 &julianintc 8>, > + <0x0800 0 0 4 &julianintc 5>, > + <0x1000 0 0 1 &julianintc 7>, > + <0x1000 0 0 2 &julianintc 8>, > + <0x1000 0 0 3 &julianintc 5>, > + <0x1000 0 0 4 &julianintc 6>; This interrupt-map looks very strange, usually the last cell is the polarity flag and here it is omitted? I would expect something like: <0x0000 0 0 1 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, (...) The interrupt-map schema in dtschema isn't really looking at this so it is easy to get it wrong. Yours, Linus Walleij
On Tue, Jan 09, 2024 at 01:42:53PM +0100, Linus Walleij wrote: > Hi Yoshinori, > > thanks for your patch! > > On Tue, Jan 9, 2024 at 9:24 AM Yoshinori Sato > <ysato@users.sourceforge.jp> wrote: > > > Renesas SH7751 PCI Controller json-schema. > > > > Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp> > (...) > > + renesas,bus-arbit-round-robin: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set DMA bus arbitration to round robin. > > + > > + pci-command-reg-fast-back-to-back: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI command register Fast Back-to-Back enable bit. > > + > > + pci-command-reg-serr: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI command register SERR# enable. > > + > > + pci-command-reg-wait-cycle-control: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI command register Wait cycle control bit. > > + > > + pci-command-reg-parity-error-response: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI Command register Parity error response bit. > > + > > + pci-command-reg-vga-snoop: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI Command register VGA palette snoop bit. > > + > > + pci-command-reg-write-invalidate: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI Command register Memory write and invaldate enable bit. > > + > > + pci-command-reg-special-cycle: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI Command register Special cycle bit. > > + > > + pci-command-reg-bus-master: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI Command register Bus master bit. > > + > > + pci-command-reg-memory-space: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI Command register Memory space bit. > > + > > + pci-command-reg-io-space: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: | > > + Set for PCI Command register I/O space bit. > > Do you really need to configure all these things? It seems they are > just set to default values anyway? > > Can't you just look at the compatible "renesas,sh7751-pci" and > set it to the values you know are needed for that compatible? Yes. Please drop all these. > > > + pci-bar: > > + $ref: /schemas/types.yaml#/definitions/uint32-matrix > > + description: Overwrite to PCI CONFIG Base Address Registers value. > > + items: > > + items: > > + - description: BAR register number > > + - description: BAR register value > > + minItems: 1 > > + maxItems: 6 > > Same with this, isn't this always the same (hardcoded) values > for "renesas,sh7751-pci" if used? The OpenFirmware PCI bus supplement already defines how to specify BAR values in DT in "reg" or "assigned-addresses". If you need to specify these, use that. Note don't expect the kernel to do anything with them. Rob > > > + interrupt-map = <0x0000 0 0 1 &julianintc 5>, > > + <0x0000 0 0 2 &julianintc 6>, > > + <0x0000 0 0 3 &julianintc 7>, > > + <0x0000 0 0 4 &julianintc 8>, > > + <0x0800 0 0 1 &julianintc 6>, > > + <0x0800 0 0 2 &julianintc 7>, > > + <0x0800 0 0 3 &julianintc 8>, > > + <0x0800 0 0 4 &julianintc 5>, > > + <0x1000 0 0 1 &julianintc 7>, > > + <0x1000 0 0 2 &julianintc 8>, > > + <0x1000 0 0 3 &julianintc 5>, > > + <0x1000 0 0 4 &julianintc 6>; > > This interrupt-map looks very strange, usually the last cell is the polarity > flag and here it is omitted? I would expect something like: > > <0x0000 0 0 1 &julianintc 5 IRQ_TYPE_LEVEL_LOW>, (...) > > The interrupt-map schema in dtschema isn't really looking at this > so it is easy to get it wrong. dtc should IIRC. Maybe not in the example being incomplete. Rob
diff --git a/Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml b/Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml new file mode 100644 index 000000000000..45e5a19e7d0f --- /dev/null +++ b/Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml @@ -0,0 +1,150 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pci/renesas,sh7751-pci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas SH7751 PCI Host controller + +maintainers: + - Yoshinori Sato <ysato@users.sourceforge.jp> + +allOf: + - $ref: /schemas/pci/pci-bus.yaml# + +properties: + compatible: + const: renesas,sh7751-pci + + reg: + minItems: 2 + maxItems: 2 + + reg-names: + items: + - const: PCI Controller + - const: Bus State Controller + + "#interrupt-cells": + const: 1 + + "#address-cells": + const: 3 + + "#size-cells": + const: 2 + + ranges: true + + dma-ranges: true + + interrupt-controller: true + + renesas,bus-arbit-round-robin: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set DMA bus arbitration to round robin. + + pci-command-reg-fast-back-to-back: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI command register Fast Back-to-Back enable bit. + + pci-command-reg-serr: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI command register SERR# enable. + + pci-command-reg-wait-cycle-control: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI command register Wait cycle control bit. + + pci-command-reg-parity-error-response: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI Command register Parity error response bit. + + pci-command-reg-vga-snoop: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI Command register VGA palette snoop bit. + + pci-command-reg-write-invalidate: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI Command register Memory write and invaldate enable bit. + + pci-command-reg-special-cycle: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI Command register Special cycle bit. + + pci-command-reg-bus-master: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI Command register Bus master bit. + + pci-command-reg-memory-space: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI Command register Memory space bit. + + pci-command-reg-io-space: + $ref: /schemas/types.yaml#/definitions/flag + description: | + Set for PCI Command register I/O space bit. + + pci-bar: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + description: Overwrite to PCI CONFIG Base Address Registers value. + items: + items: + - description: BAR register number + - description: BAR register value + minItems: 1 + maxItems: 6 + +required: + - compatible + - reg + - "#interrupt-cells" + - "#address-cells" + - "#size-cells" + - ranges + - interrupt-map + - interrupt-map-mask + +unevaluatedProperties: false + +examples: + - | + pci@fe200000 { + compatible = "renesas,sh7751-pci"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-controller; + device_type = "pci"; + bus-range = <0 0>; + ranges = <0x02000000 0 0xfd000000 0xfd000000 0 0x01000000>, + <0x01000000 0 0x00000000 0xfe240000 0 0x00040000>; + dma-ranges = <0x02000000 0 0xc000000 0x0c000000 0 0x04000000>; + reg = <0xfe200000 0x0400>, + <0xff800000 0x0100>; + interrupt-map = <0x0000 0 0 1 &julianintc 5>, + <0x0000 0 0 2 &julianintc 6>, + <0x0000 0 0 3 &julianintc 7>, + <0x0000 0 0 4 &julianintc 8>, + <0x0800 0 0 1 &julianintc 6>, + <0x0800 0 0 2 &julianintc 7>, + <0x0800 0 0 3 &julianintc 8>, + <0x0800 0 0 4 &julianintc 5>, + <0x1000 0 0 1 &julianintc 7>, + <0x1000 0 0 2 &julianintc 8>, + <0x1000 0 0 3 &julianintc 5>, + <0x1000 0 0 4 &julianintc 6>; + pci-bar = <0 0xab000001>, <2 0xd0000000>; + pci-command-reg-io-space; + interrupt-map-mask = <0x1800 0 0 7>; + };
Renesas SH7751 PCI Controller json-schema. Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp> --- .../bindings/pci/renesas,sh7751-pci.yaml | 150 ++++++++++++++++++ 1 file changed, 150 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml