| Message ID | 1633628923-25047-3-git-send-email-pmaliset@codeaurora.org (mailing list archive) |
|---|---|
| State | Not Applicable |
| Delegated to: | Lorenzo Pieralisi |
| Headers | show |
| Series | Add DT bindings and DT nodes for PCIe and PHY in SC7280 | expand |
On 07/10/2021 20:48, Prasad Malisetty wrote: > Add PCIe controller and PHY nodes for sc7280 SOC. > > Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org> > Reviewed-by: Stephen Boyd <swboyd@chromium.org> > --- > arch/arm64/boot/dts/qcom/sc7280.dtsi | 118 +++++++++++++++++++++++++++++++++++ > 1 file changed, 118 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi > index 39635da..cde814f 100644 > --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi > +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi > @@ -1563,6 +1563,117 @@ > qcom,bcm-voters = <&apps_bcm_voter>; > }; > > + pcie1: pci@1c08000 { > + compatible = "qcom,pcie-sc7280"; > + reg = <0 0x01c08000 0 0x3000>, > + <0 0x40000000 0 0xf1d>, > + <0 0x40000f20 0 0xa8>, > + <0 0x40001000 0 0x1000>, > + <0 0x40100000 0 0x100000>; > + > + reg-names = "parf", "dbi", "elbi", "atu", "config"; > + device_type = "pci"; > + linux,pci-domain = <1>; > + bus-range = <0x00 0xff>; > + num-lanes = <2>; > + > + #address-cells = <3>; > + #size-cells = <2>; > + > + ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, > + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>; > + > + interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "msi"; > + #interrupt-cells = <1>; > + interrupt-map-mask = <0 0 0 0x7>; > + interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, > + <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, > + <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, > + <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; > + > + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, > + <&gcc GCC_PCIE_1_PIPE_CLK_SRC>, > + <&pcie1_lane 0>, This should be just <&pcie1_lane>, as the phy doesn't have clock cells. > + <&rpmhcc RPMH_CXO_CLK>, > + <&gcc GCC_PCIE_1_AUX_CLK>, > + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, > + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, > + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, > + <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>, > + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, > + <&gcc GCC_DDRSS_PCIE_SF_CLK>; > + > + clock-names = "pipe", > + "pipe_mux", > + "phy_pipe", > + "ref", > + "aux", > + "cfg", > + "bus_master", > + "bus_slave", > + "slave_q2a", > + "tbu", > + "ddrss_sf_tbu"; > + > + assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>; > + assigned-clock-rates = <19200000>; > + > + resets = <&gcc GCC_PCIE_1_BCR>; > + reset-names = "pci"; > + > + power-domains = <&gcc GCC_PCIE_1_GDSC>; > + > + phys = <&pcie1_lane>; > + phy-names = "pciephy"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie1_clkreq_n>; > + > + iommus = <&apps_smmu 0x1c80 0x1>; > + > + iommu-map = <0x0 &apps_smmu 0x1c80 0x1>, > + <0x100 &apps_smmu 0x1c81 0x1>; > + > + status = "disabled"; > + }; > + > + pcie1_phy: phy@1c0e000 { > + compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy"; > + reg = <0 0x01c0e000 0 0x1c0>; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + clocks = <&gcc GCC_PCIE_1_AUX_CLK>, > + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, > + <&gcc GCC_PCIE_CLKREF_EN>, > + <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; > + clock-names = "aux", "cfg_ahb", "ref", "refgen"; > + > + resets = <&gcc GCC_PCIE_1_PHY_BCR>; > + reset-names = "phy"; > + > + assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; > + assigned-clock-rates = <100000000>; > + > + status = "disabled"; > + > + pcie1_lane: lanes@1c0e200 { > + reg = <0 0x01c0e200 0 0x170>, > + <0 0x01c0e400 0 0x200>, > + <0 0x01c0ea00 0 0x1f0>, > + <0 0x01c0e600 0 0x170>, > + <0 0x01c0e800 0 0x200>, > + <0 0x01c0ee00 0 0xf4>; > + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>; > + clock-names = "pipe0"; > + > + #phy-cells = <0>; > + #clock-cells = <1>; > + clock-output-names = "pcie_1_pipe_clk"; > + }; > + }; > + > ipa: ipa@1e40000 { > compatible = "qcom,sc7280-ipa"; > > @@ -2676,6 +2787,13 @@ > gpio-ranges = <&tlmm 0 0 175>; > wakeup-parent = <&pdc>; > > + pcie1_clkreq_n: pcie1-clkreq-n { > + pins = "gpio79"; > + function = "pcie1_clkreqn"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > qspi_clk: qspi-clk { > pins = "gpio14"; > function = "qspi_clk"; >
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi index 39635da..cde814f 100644 --- a/arch/arm64/boot/dts/qcom/sc7280.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi @@ -1563,6 +1563,117 @@ qcom,bcm-voters = <&apps_bcm_voter>; }; + pcie1: pci@1c08000 { + compatible = "qcom,pcie-sc7280"; + reg = <0 0x01c08000 0 0x3000>, + <0 0x40000000 0 0xf1d>, + <0 0x40000f20 0 0xa8>, + <0 0x40001000 0 0x1000>, + <0 0x40100000 0 0x100000>; + + reg-names = "parf", "dbi", "elbi", "atu", "config"; + device_type = "pci"; + linux,pci-domain = <1>; + bus-range = <0x00 0xff>; + num-lanes = <2>; + + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>; + + interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, + <&gcc GCC_PCIE_1_PIPE_CLK_SRC>, + <&pcie1_lane 0>, + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_PCIE_1_AUX_CLK>, + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, + <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>, + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, + <&gcc GCC_DDRSS_PCIE_SF_CLK>; + + clock-names = "pipe", + "pipe_mux", + "phy_pipe", + "ref", + "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "tbu", + "ddrss_sf_tbu"; + + assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>; + assigned-clock-rates = <19200000>; + + resets = <&gcc GCC_PCIE_1_BCR>; + reset-names = "pci"; + + power-domains = <&gcc GCC_PCIE_1_GDSC>; + + phys = <&pcie1_lane>; + phy-names = "pciephy"; + + pinctrl-names = "default"; + pinctrl-0 = <&pcie1_clkreq_n>; + + iommus = <&apps_smmu 0x1c80 0x1>; + + iommu-map = <0x0 &apps_smmu 0x1c80 0x1>, + <0x100 &apps_smmu 0x1c81 0x1>; + + status = "disabled"; + }; + + pcie1_phy: phy@1c0e000 { + compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy"; + reg = <0 0x01c0e000 0 0x1c0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_PCIE_1_AUX_CLK>, + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, + <&gcc GCC_PCIE_CLKREF_EN>, + <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "refgen"; + + resets = <&gcc GCC_PCIE_1_PHY_BCR>; + reset-names = "phy"; + + assigned-clocks = <&gcc GCC_PCIE1_PHY_RCHNG_CLK>; + assigned-clock-rates = <100000000>; + + status = "disabled"; + + pcie1_lane: lanes@1c0e200 { + reg = <0 0x01c0e200 0 0x170>, + <0 0x01c0e400 0 0x200>, + <0 0x01c0ea00 0 0x1f0>, + <0 0x01c0e600 0 0x170>, + <0 0x01c0e800 0 0x200>, + <0 0x01c0ee00 0 0xf4>; + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>; + clock-names = "pipe0"; + + #phy-cells = <0>; + #clock-cells = <1>; + clock-output-names = "pcie_1_pipe_clk"; + }; + }; + ipa: ipa@1e40000 { compatible = "qcom,sc7280-ipa"; @@ -2676,6 +2787,13 @@ gpio-ranges = <&tlmm 0 0 175>; wakeup-parent = <&pdc>; + pcie1_clkreq_n: pcie1-clkreq-n { + pins = "gpio79"; + function = "pcie1_clkreqn"; + drive-strength = <2>; + bias-pull-up; + }; + qspi_clk: qspi-clk { pins = "gpio14"; function = "qspi_clk";