diff mbox series

[v12,7/8] dmaengine: dw-edma: Add support for chip specific flags

Message ID 20220524152159.2370739-8-Frank.Li@nxp.com (mailing list archive)
State Accepted
Headers show
Series Enable designware PCI EP EDMA locally | expand

Commit Message

Frank Li May 24, 2022, 3:21 p.m. UTC
Add a "flags" field to the "struct dw_edma_chip" so that the controller
drivers can pass flags that are relevant to the platform.

DW_EDMA_CHIP_LOCAL - Used by the controller drivers accessing eDMA
locally. Local eDMA access doesn't require generating MSIs to the remote.

Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
Change from v7 to v12
 -none
Change from v6 to v7
 - dw_edma_chip_flags to u32
Change from v5 to v6
 - use enum instead of define

Change from v4 to v5
 - split two two patch
 - rework commit message
Change from v3 to v4
none
Change from v2 to v3
 - rework commit message
 - Change to DW_EDMA_CHIP_32BIT_DBI
 - using DW_EDMA_CHIP_LOCAL control msi
 - Apply Bjorn's comments,
        if (!j) {
               control |= DW_EDMA_V0_LIE;
               if (!(chan->chip->flags & DW_EDMA_CHIP_LOCAL))
                               control |= DW_EDMA_V0_RIE;
        }

        if ((chan->chip->flags & DW_EDMA_CHIP_REG32BIT) ||
              !IS_ENABLED(CONFIG_64BIT)) {
          SET_CH_32(...);
          SET_CH_32(...);
       } else {
          SET_CH_64(...);
       }


Change from v1 to v2
- none
 drivers/dma/dw-edma/dw-edma-v0-core.c |  9 ++++++---
 include/linux/dma/edma.h              | 10 ++++++++++
 2 files changed, 16 insertions(+), 3 deletions(-)
diff mbox series

Patch

diff --git a/drivers/dma/dw-edma/dw-edma-v0-core.c b/drivers/dma/dw-edma/dw-edma-v0-core.c
index 403ade40c1b1b..607647dacc291 100644
--- a/drivers/dma/dw-edma/dw-edma-v0-core.c
+++ b/drivers/dma/dw-edma/dw-edma-v0-core.c
@@ -301,6 +301,7 @@  u32 dw_edma_v0_core_status_abort_int(struct dw_edma *dw, enum dw_edma_dir dir)
 static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 {
 	struct dw_edma_burst *child;
+	struct dw_edma_chan *chan = chunk->chan;
 	struct dw_edma_v0_lli __iomem *lli;
 	struct dw_edma_v0_llp __iomem *llp;
 	u32 control = 0, i = 0;
@@ -314,9 +315,11 @@  static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 	j = chunk->bursts_alloc;
 	list_for_each_entry(child, &chunk->burst->list, list) {
 		j--;
-		if (!j)
-			control |= (DW_EDMA_V0_LIE | DW_EDMA_V0_RIE);
-
+		if (!j) {
+			control |= DW_EDMA_V0_LIE;
+			if (!(chan->dw->chip->flags & DW_EDMA_CHIP_LOCAL))
+				control |= DW_EDMA_V0_RIE;
+		}
 		/* Channel control */
 		SET_LL_32(&lli[i].control, control);
 		/* Transfer size */
diff --git a/include/linux/dma/edma.h b/include/linux/dma/edma.h
index c8b479f1d4da7..7baf16fd4f233 100644
--- a/include/linux/dma/edma.h
+++ b/include/linux/dma/edma.h
@@ -33,12 +33,21 @@  enum dw_edma_map_format {
 	EDMA_MF_HDMA_COMPAT = 0x5
 };
 
+/**
+ * enum dw_edma_chip_flags - Flags specific to an eDMA chip
+ * @DW_EDMA_CHIP_LOCAL:		eDMA is used locally by an endpoint
+ */
+enum dw_edma_chip_flags {
+	DW_EDMA_CHIP_LOCAL	= BIT(0),
+};
+
 /**
  * struct dw_edma_chip - representation of DesignWare eDMA controller hardware
  * @dev:		 struct device of the eDMA controller
  * @id:			 instance ID
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
+ * @flags		 dw_edma_chip_flags
  * @reg_base		 DMA register base address
  * @ll_wr_cnt		 DMA write link list count
  * @ll_rd_cnt		 DMA read link list count
@@ -55,6 +64,7 @@  struct dw_edma_chip {
 	int			id;
 	int			nr_irqs;
 	const struct dw_edma_core_ops   *ops;
+	u32			flags;
 
 	void __iomem		*reg_base;