diff mbox series

[v6,11/11] arm64: dts: mt7986: add BPI-R3 nand/nor overlays

Message ID 20221118190126.100895-12-linux@fw-web.de (mailing list archive)
State Superseded
Headers show
Series Add BananaPi R3 | expand

Commit Message

Frank Wunderlich Nov. 18, 2022, 7:01 p.m. UTC
From: Frank Wunderlich <frank-w@public-files.de>

Add devicetree overlays for using nand and nor on BPI-R3.

Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
---
maybe rename to dtso?

"kbuild: Allow DTB overlays to built from .dtso named source files"
https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2

more comments about the dt overlay-support:

https://patchwork.kernel.org/comment/25092116/
https://patchwork.kernel.org/comment/25085681/
---
v4:
- drop compile-comment from overlays
- add author-information to dt-overlays
---
 arch/arm64/boot/dts/mediatek/Makefile         |  2 +
 .../mediatek/mt7986a-bananapi-bpi-r3-nand.dts | 55 +++++++++++++++
 .../mediatek/mt7986a-bananapi-bpi-r3-nor.dts  | 69 +++++++++++++++++++
 3 files changed, 126 insertions(+)
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dts
 create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dts

Comments

Rob Herring Nov. 8, 2022, 2:45 p.m. UTC | #1
On Fri, Nov 18, 2022 at 4:05 PM Frank Wunderlich
<frank-w@public-files.de> wrote:
>
> Am 18. November 2022 22:39:52 MEZ schrieb Rob Herring <robh+dt@kernel.org>:
> >On Fri, Nov 18, 2022 at 1:01 PM Frank Wunderlich <linux@fw-web.de> wrote:
> >>
> >> From: Frank Wunderlich <frank-w@public-files.de>
> >>
> >> Add devicetree overlays for using nand and nor on BPI-R3.
> >
> >Can you not tell at runtime which one you booted from? If not, how
> >does one choose which overlay to apply? If you can, why not populate
> >both nodes and enable the right one? IMO, if all h/w is present, it
> >should all be in the DT. Selecting what h/w to use is a separate
> >problem and overlays aren't a great solution for that.
>
> It is not the decision about bootdevice,more available devices.
>
> Only 1 spi device (nand OR nor) is available
> at boottime as they share same spi bus and
> chipselect is set via hw jumper.
> Both nodes have reg 0,which is imho not
> supported in linux.

As long as one is set to disabled, it should be fine.


> I choosed overlays to add the right spi
> device on the right mmc device where
> similar selection happens (see patch 10).
> Either sd OR emmc can be used (1 mmc
> controller,first 4bits from bus switched by
> hardware jumper).But for mmc i use it as
> base fdt because i see mmc as primary
> device which holds rootfs too. Nand/nor is
> imho helping device for accessing emmc or
> like rescue system (only uboot).

No way to read the jumper state or know what you booted from I gues?

> I probe in uboot if emmc is available (mmc
>  partconf) and choose emmc else sd. For
>  spi i try with sf command to check for nor,if
>  this does not work i apply nand overlay.

Instead of applying overlays, wouldn't just changing 'status' be easier?

>
> >> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> >> ---
> >> maybe rename to dtso?
> >>
> >> "kbuild: Allow DTB overlays to built from .dtso named source files"
> >> https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2
>
> Should i do this?

Yes. .dts -> .dtbo is going to be removed.

> >> more comments about the dt overlay-support:
> >>
> >> https://patchwork.kernel.org/comment/25092116/
> >> https://patchwork.kernel.org/comment/25085681/
>
> Daniel suggest define sd/emmc as overlay too...with way you mention below we could create 4 full fdt without applying overlays in uboot.

Yes, but if you are going to do that, then you can just do all this
with includes.

> >> --- a/arch/arm64/boot/dts/mediatek/Makefile
> >> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> >> @@ -8,6 +8,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
> >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
> >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
> >
> >These need rules to apply them to the base dtb(s). You just need:
> >
> >full.dtb := base.dtb overlay.dtb
> >dtb-y += full.dtb
>
> I would prefer to do this in bootloader to allow all 4 possible configurations:
>
> Sd+nand
> Sd+nor
> Emmc+nand
> Emmc+nor

That's fine. The purpose here is to document what the overlays apply
to, check that they actually apply, and validate them when applied
(unless someone wants to figure out all the issues with validating
just an overlay and make that work). You for example have an
undocumented compatible in yours (denx,fit).

Rob
Rob Herring Nov. 18, 2022, 9:39 p.m. UTC | #2
On Fri, Nov 18, 2022 at 1:01 PM Frank Wunderlich <linux@fw-web.de> wrote:
>
> From: Frank Wunderlich <frank-w@public-files.de>
>
> Add devicetree overlays for using nand and nor on BPI-R3.

Can you not tell at runtime which one you booted from? If not, how
does one choose which overlay to apply? If you can, why not populate
both nodes and enable the right one? IMO, if all h/w is present, it
should all be in the DT. Selecting what h/w to use is a separate
problem and overlays aren't a great solution for that.


> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> ---
> maybe rename to dtso?
>
> "kbuild: Allow DTB overlays to built from .dtso named source files"
> https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2
>
> more comments about the dt overlay-support:
>
> https://patchwork.kernel.org/comment/25092116/
> https://patchwork.kernel.org/comment/25085681/
> ---
> v4:
> - drop compile-comment from overlays
> - add author-information to dt-overlays
> ---
>  arch/arm64/boot/dts/mediatek/Makefile         |  2 +
>  .../mediatek/mt7986a-bananapi-bpi-r3-nand.dts | 55 +++++++++++++++
>  .../mediatek/mt7986a-bananapi-bpi-r3-nor.dts  | 69 +++++++++++++++++++
>  3 files changed, 126 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dts
>  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dts
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index e8902f2cc58f..d42208c4090d 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -8,6 +8,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo

These need rules to apply them to the base dtb(s). You just need:

full.dtb := base.dtb overlay.dtb
dtb-y += full.dtb

Rob
Rob Herring Nov. 18, 2022, 9:45 p.m. UTC | #3
On Fri, Nov 18, 2022 at 3:39 PM Rob Herring <robh+dt@kernel.org> wrote:
>
> On Fri, Nov 18, 2022 at 1:01 PM Frank Wunderlich <linux@fw-web.de> wrote:
> >
> > From: Frank Wunderlich <frank-w@public-files.de>
> >
> > Add devicetree overlays for using nand and nor on BPI-R3.
>
> Can you not tell at runtime which one you booted from? If not, how
> does one choose which overlay to apply? If you can, why not populate
> both nodes and enable the right one? IMO, if all h/w is present, it
> should all be in the DT. Selecting what h/w to use is a separate
> problem and overlays aren't a great solution for that.
>
>
> > Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> > ---
> > maybe rename to dtso?
> >
> > "kbuild: Allow DTB overlays to built from .dtso named source files"
> > https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2
> >
> > more comments about the dt overlay-support:
> >
> > https://patchwork.kernel.org/comment/25092116/
> > https://patchwork.kernel.org/comment/25085681/
> > ---
> > v4:
> > - drop compile-comment from overlays
> > - add author-information to dt-overlays
> > ---
> >  arch/arm64/boot/dts/mediatek/Makefile         |  2 +
> >  .../mediatek/mt7986a-bananapi-bpi-r3-nand.dts | 55 +++++++++++++++
> >  .../mediatek/mt7986a-bananapi-bpi-r3-nor.dts  | 69 +++++++++++++++++++
> >  3 files changed, 126 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dts
> >  create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dts
> >
> > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> > index e8902f2cc58f..d42208c4090d 100644
> > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > @@ -8,6 +8,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> >  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> >  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> >  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
>
> These need rules to apply them to the base dtb(s). You just need:
>
> full.dtb := base.dtb overlay.dtb

Oops, that should be:

full-dtbs := base.dtb overlay.dtb
dtb-y += full.dtb

Just like multiple objs in a module.

Rob
Frank Wunderlich Nov. 18, 2022, 10:05 p.m. UTC | #4
Am 18. November 2022 22:39:52 MEZ schrieb Rob Herring <robh+dt@kernel.org>:
>On Fri, Nov 18, 2022 at 1:01 PM Frank Wunderlich <linux@fw-web.de> wrote:
>>
>> From: Frank Wunderlich <frank-w@public-files.de>
>>
>> Add devicetree overlays for using nand and nor on BPI-R3.
>
>Can you not tell at runtime which one you booted from? If not, how
>does one choose which overlay to apply? If you can, why not populate
>both nodes and enable the right one? IMO, if all h/w is present, it
>should all be in the DT. Selecting what h/w to use is a separate
>problem and overlays aren't a great solution for that.

It is not the decision about bootdevice,more available devices.

Only 1 spi device (nand OR nor) is available
at boottime as they share same spi bus and
chipselect is set via hw jumper.
Both nodes have reg 0,which is imho not
supported in linux.

I choosed overlays to add the right spi
device on the right mmc device where
similar selection happens (see patch 10).
Either sd OR emmc can be used (1 mmc
controller,first 4bits from bus switched by
hardware jumper).But for mmc i use it as
base fdt because i see mmc as primary
device which holds rootfs too. Nand/nor is
imho helping device for accessing emmc or
like rescue system (only uboot).

I probe in uboot if emmc is available (mmc
 partconf) and choose emmc else sd. For
 spi i try with sf command to check for nor,if
 this does not work i apply nand overlay.

>> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
>> ---
>> maybe rename to dtso?
>>
>> "kbuild: Allow DTB overlays to built from .dtso named source files"
>> https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2

Should i do this?

>> more comments about the dt overlay-support:
>>
>> https://patchwork.kernel.org/comment/25092116/
>> https://patchwork.kernel.org/comment/25085681/

Daniel suggest define sd/emmc as overlay too...with way you mention below we could create 4 full fdt without applying overlays in uboot.

>> --- a/arch/arm64/boot/dts/mediatek/Makefile
>> +++ b/arch/arm64/boot/dts/mediatek/Makefile
>> @@ -8,6 +8,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
>>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
>>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
>>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
>
>These need rules to apply them to the base dtb(s). You just need:
>
>full.dtb := base.dtb overlay.dtb
>dtb-y += full.dtb

I would prefer to do this in bootloader to allow all 4 possible configurations:

Sd+nand
Sd+nor
Emmc+nand
Emmc+nor

>Rob

Hi,
regards Frank
Frank Wunderlich Nov. 19, 2022, 7:19 a.m. UTC | #5
Am 8. November 2022 15:45:49 MEZ schrieb Rob Herring <robh+dt@kernel.org>:
>On Fri, Nov 18, 2022 at 4:05 PM Frank Wunderlich
><frank-w@public-files.de> wrote:
>>
>> Am 18. November 2022 22:39:52 MEZ schrieb Rob Herring <robh+dt@kernel.org>:
>> >On Fri, Nov 18, 2022 at 1:01 PM Frank Wunderlich <linux@fw-web.de> wrote:
>> >>
>> >> From: Frank Wunderlich <frank-w@public-files.de>
>> >>
>> >> Add devicetree overlays for using nand and nor on BPI-R3.
>> >
>> >Can you not tell at runtime which one you booted from? If not, how
>> >does one choose which overlay to apply? If you can, why not populate
>> >both nodes and enable the right one? IMO, if all h/w is present, it
>> >should all be in the DT. Selecting what h/w to use is a separate
>> >problem and overlays aren't a great solution for that.
>>
>> It is not the decision about bootdevice,more available devices.
>>
>> Only 1 spi device (nand OR nor) is available
>> at boottime as they share same spi bus and
>> chipselect is set via hw jumper.
>> Both nodes have reg 0,which is imho not
>> supported in linux.
>
>As long as one is set to disabled, it should be fine.
>
>
>> I choosed overlays to add the right spi
>> device on the right mmc device where
>> similar selection happens (see patch 10).
>> Either sd OR emmc can be used (1 mmc
>> controller,first 4bits from bus switched by
>> hardware jumper).But for mmc i use it as
>> base fdt because i see mmc as primary
>> device which holds rootfs too. Nand/nor is
>> imho helping device for accessing emmc or
>> like rescue system (only uboot).
>
>No way to read the jumper state or know what you booted from I gues?
>
>> I probe in uboot if emmc is available (mmc
>>  partconf) and choose emmc else sd. For
>>  spi i try with sf command to check for nor,if
>>  this does not work i apply nand overlay.
>
>Instead of applying overlays, wouldn't just changing 'status' be easier?

It will be easier,but requires dts for all
 combinations,we have have sd/emmc
 combination twice (once for nand
 enabling,once for nor) and we have then 4
 full dts instead of smaller overlays in fit.

So i should add spi subnodes both disabled
 in base dtsi and create 4 dts (sd-nand,sd-nor,emmc-nand,emmc-nor) with
 mmc node and enabling the right spi node?
>>
>> >> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
>> >> ---
>> >> maybe rename to dtso?
>> >>
>> >> "kbuild: Allow DTB overlays to built from .dtso named source files"
>> >> https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2
>>
>> Should i do this?
>
>Yes. .dts -> .dtbo is going to be removed.

Do this if still using overlays,will test new way.

Maybe we can apply parts 1-9 first?

>> >> more comments about the dt overlay-support:
>> >>
>> >> https://patchwork.kernel.org/comment/25092116/
>> >> https://patchwork.kernel.org/comment/25085681/
>>
>> Daniel suggest define sd/emmc as overlay too...with way you mention below we could create 4 full fdt without applying overlays in uboot.
>
>Yes, but if you are going to do that, then you can just do all this
>with includes.

This is a third way if i understand correctly

Make all of them as overlay (dtso?) but
 build dtb by combining them in makefile.

This looks the best way because it avoids
 redundand code for mmc node and allows
 my current spi config (not the status way
 which may break due to same unit address).

I guess my base dtsi is then a dts too?

Or should these overlays only duplicated and either include sd dts or emmc dts (but this creates again redundant code)?
>> >> --- a/arch/arm64/boot/dts/mediatek/Makefile
>> >> +++ b/arch/arm64/boot/dts/mediatek/Makefile
>> >> @@ -8,6 +8,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
>> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
>> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
>> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
>> >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
>> >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
>> >
>> >These need rules to apply them to the base dtb(s). You just need:
>> >
>> >full.dtb := base.dtb overlay.dtb
>> >dtb-y += full.dtb
>>
>> I would prefer to do this in bootloader to allow all 4 possible configurations:
>>
>> Sd+nand
>> Sd+nor
>> Emmc+nand
>> Emmc+nor
>
>That's fine. The purpose here is to document what the overlays apply
>to, check that they actually apply, and validate them when applied
>(unless someone wants to figure out all the issues with validating
>just an overlay and make that work). You for example have an
>undocumented compatible in yours (denx,fit).

Oh,need to check,copied partitions from my
 uboot dts...maybe there is a linux version
 for marking it as fit partition,else i drop
 completely.

So i i stay with current way i have to rename
 overlays to dtso and add info about base
 dtb (bpi-r3-sd/emmc) to commit message
 or into the overlay itself?

>Rob


regards Frank
Rob Herring (Arm) Nov. 20, 2022, 4:12 p.m. UTC | #6
On Sat, Nov 19, 2022 at 08:19:52AM +0100, Frank Wunderlich wrote:
> Am 8. November 2022 15:45:49 MEZ schrieb Rob Herring <robh+dt@kernel.org>:
> >On Fri, Nov 18, 2022 at 4:05 PM Frank Wunderlich
> ><frank-w@public-files.de> wrote:
> >>
> >> Am 18. November 2022 22:39:52 MEZ schrieb Rob Herring <robh+dt@kernel.org>:
> >> >On Fri, Nov 18, 2022 at 1:01 PM Frank Wunderlich <linux@fw-web.de> wrote:
> >> >>
> >> >> From: Frank Wunderlich <frank-w@public-files.de>
> >> >>
> >> >> Add devicetree overlays for using nand and nor on BPI-R3.
> >> >
> >> >Can you not tell at runtime which one you booted from? If not, how
> >> >does one choose which overlay to apply? If you can, why not populate
> >> >both nodes and enable the right one? IMO, if all h/w is present, it
> >> >should all be in the DT. Selecting what h/w to use is a separate
> >> >problem and overlays aren't a great solution for that.
> >>
> >> It is not the decision about bootdevice,more available devices.
> >>
> >> Only 1 spi device (nand OR nor) is available
> >> at boottime as they share same spi bus and
> >> chipselect is set via hw jumper.
> >> Both nodes have reg 0,which is imho not
> >> supported in linux.
> >
> >As long as one is set to disabled, it should be fine.
> >
> >
> >> I choosed overlays to add the right spi
> >> device on the right mmc device where
> >> similar selection happens (see patch 10).
> >> Either sd OR emmc can be used (1 mmc
> >> controller,first 4bits from bus switched by
> >> hardware jumper).But for mmc i use it as
> >> base fdt because i see mmc as primary
> >> device which holds rootfs too. Nand/nor is
> >> imho helping device for accessing emmc or
> >> like rescue system (only uboot).
> >
> >No way to read the jumper state or know what you booted from I gues?
> >
> >> I probe in uboot if emmc is available (mmc
> >>  partconf) and choose emmc else sd. For
> >>  spi i try with sf command to check for nor,if
> >>  this does not work i apply nand overlay.
> >
> >Instead of applying overlays, wouldn't just changing 'status' be easier?
> 
> It will be easier,but requires dts for all
>  combinations,we have have sd/emmc
>  combination twice (once for nand
>  enabling,once for nor) and we have then 4
>  full dts instead of smaller overlays in fit.

No, I mean can't you have 1 dtb with everything, but nand, nor, emmc, 
and sd are all disabled. Then at boot change 'status' for what's 
enabled.


> So i should add spi subnodes both disabled
>  in base dtsi and create 4 dts (sd-nand,sd-nor,emmc-nand,emmc-nor) with
>  mmc node and enabling the right spi node?
> >>
> >> >> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> >> >> ---
> >> >> maybe rename to dtso?
> >> >>
> >> >> "kbuild: Allow DTB overlays to built from .dtso named source files"
> >> >> https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2
> >>
> >> Should i do this?
> >
> >Yes. .dts -> .dtbo is going to be removed.
> 
> Do this if still using overlays,will test new way.
> 
> Maybe we can apply parts 1-9 first?

Sure.

> 
> >> >> more comments about the dt overlay-support:
> >> >>
> >> >> https://patchwork.kernel.org/comment/25092116/
> >> >> https://patchwork.kernel.org/comment/25085681/
> >>
> >> Daniel suggest define sd/emmc as overlay too...with way you mention below we could create 4 full fdt without applying overlays in uboot.
> >
> >Yes, but if you are going to do that, then you can just do all this
> >with includes.
> 
> This is a third way if i understand correctly
> 
> Make all of them as overlay (dtso?) but
>  build dtb by combining them in makefile.
> 
> This looks the best way because it avoids
>  redundand code for mmc node and allows
>  my current spi config (not the status way
>  which may break due to same unit address).
> 
> I guess my base dtsi is then a dts too?

Yes, it can be.

> 
> Or should these overlays only duplicated and either include sd dts or emmc dts (but this creates again redundant code)?
> >> >> --- a/arch/arm64/boot/dts/mediatek/Makefile
> >> >> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> >> >> @@ -8,6 +8,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> >> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> >> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> >> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
> >> >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
> >> >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
> >> >
> >> >These need rules to apply them to the base dtb(s). You just need:
> >> >
> >> >full.dtb := base.dtb overlay.dtb
> >> >dtb-y += full.dtb
> >>
> >> I would prefer to do this in bootloader to allow all 4 possible configurations:
> >>
> >> Sd+nand
> >> Sd+nor
> >> Emmc+nand
> >> Emmc+nor
> >
> >That's fine. The purpose here is to document what the overlays apply
> >to, check that they actually apply, and validate them when applied
> >(unless someone wants to figure out all the issues with validating
> >just an overlay and make that work). You for example have an
> >undocumented compatible in yours (denx,fit).
> 
> Oh,need to check,copied partitions from my
>  uboot dts...maybe there is a linux version
>  for marking it as fit partition,else i drop
>  completely.

You just need to document it. But the first thing I'm going to say, is 
'u-boot' is the vendor, not 'denx'. So 'u-boot,fit'.

Rob
Frank Wunderlich Nov. 20, 2022, 4:47 p.m. UTC | #7
Hi

> Gesendet: Sonntag, 20. November 2022 um 17:12 Uhr
> Von: "Rob Herring" <robh@kernel.org>
> On Sat, Nov 19, 2022 at 08:19:52AM +0100, Frank Wunderlich wrote:
> > Am 8. November 2022 15:45:49 MEZ schrieb Rob Herring <robh+dt@kernel.org>:
> > >On Fri, Nov 18, 2022 at 4:05 PM Frank Wunderlich
> > ><frank-w@public-files.de> wrote:
> > >>
> > >> Am 18. November 2022 22:39:52 MEZ schrieb Rob Herring <robh+dt@kernel.org>:
> > >> >On Fri, Nov 18, 2022 at 1:01 PM Frank Wunderlich <linux@fw-web.de> wrote:
> > >> >>
> > >> >> From: Frank Wunderlich <frank-w@public-files.de>
> > >> >>
> > >> >> Add devicetree overlays for using nand and nor on BPI-R3.
> > >> >
> > >> >Can you not tell at runtime which one you booted from? If not, how
> > >> >does one choose which overlay to apply? If you can, why not populate
> > >> >both nodes and enable the right one? IMO, if all h/w is present, it
> > >> >should all be in the DT. Selecting what h/w to use is a separate
> > >> >problem and overlays aren't a great solution for that.
> > >>
> > >> It is not the decision about bootdevice,more available devices.
> > >>
> > >> Only 1 spi device (nand OR nor) is available
> > >> at boottime as they share same spi bus and
> > >> chipselect is set via hw jumper.
> > >> Both nodes have reg 0,which is imho not
> > >> supported in linux.
> > >
> > >As long as one is set to disabled, it should be fine.
> > >
> > >
> > >> I choosed overlays to add the right spi
> > >> device on the right mmc device where
> > >> similar selection happens (see patch 10).
> > >> Either sd OR emmc can be used (1 mmc
> > >> controller,first 4bits from bus switched by
> > >> hardware jumper).But for mmc i use it as
> > >> base fdt because i see mmc as primary
> > >> device which holds rootfs too. Nand/nor is
> > >> imho helping device for accessing emmc or
> > >> like rescue system (only uboot).
> > >
> > >No way to read the jumper state or know what you booted from I gues?
> > >
> > >> I probe in uboot if emmc is available (mmc
> > >>  partconf) and choose emmc else sd. For
> > >>  spi i try with sf command to check for nor,if
> > >>  this does not work i apply nand overlay.
> > >
> > >Instead of applying overlays, wouldn't just changing 'status' be easier?
> >
> > It will be easier,but requires dts for all
> >  combinations,we have have sd/emmc
> >  combination twice (once for nand
> >  enabling,once for nor) and we have then 4
> >  full dts instead of smaller overlays in fit.
>
> No, I mean can't you have 1 dtb with everything, but nand, nor, emmc,
> and sd are all disabled. Then at boot change 'status' for what's
> enabled.

at least for sd/emmc: no, as they share same mmc-node with different settings (bus-width,speed,...).

for nand/nor i'm not sure if spi can have 2 childs with same unit-address/reg even if disabled.
Then i do not know how to enable a dts-node in uboot...only know (not long time) how to apply overlay ;)

> > So i should add spi subnodes both disabled
> >  in base dtsi and create 4 dts (sd-nand,sd-nor,emmc-nand,emmc-nor) with
> >  mmc node and enabling the right spi node?
> > >>
> > >> >> Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
> > >> >> ---
> > >> >> maybe rename to dtso?
> > >> >>
> > >> >> "kbuild: Allow DTB overlays to built from .dtso named source files"
> > >> >> https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git/commit/?h=dt/next&id=363547d2191cbc32ca954ba75d72908712398ff2
> > >>
> > >> Should i do this?
> > >
> > >Yes. .dts -> .dtbo is going to be removed.
> >
> > Do this if still using overlays,will test new way.
> >
> > Maybe we can apply parts 1-9 first?
>
> Sure.

i would wait for them applied before posting next version, i hope they can go into 6.2. Then it is easier because depencies are all in.

overlay was only for discussion the right way...my preferred way was mmc in board dts and spi as overlay,
daniel preferred base fdt without them all and 4 overlays. another way already discussed were 4 full fdt, but
how to get all 4 combinations with less files and not defining mmc/spi device twice? i see only the overlay
version and combining via Makefile.

what is your preferred way (except all devices in 1 dts which is afair not possible, daniel please correct me if
i'm wrong)?

> >
> > >> >> more comments about the dt overlay-support:
> > >> >>
> > >> >> https://patchwork.kernel.org/comment/25092116/
> > >> >> https://patchwork.kernel.org/comment/25085681/
> > >>
> > >> Daniel suggest define sd/emmc as overlay too...with way you mention below we could create 4 full fdt without applying overlays in uboot.
> > >
> > >Yes, but if you are going to do that, then you can just do all this
> > >with includes.
> >
> > This is a third way if i understand correctly
> >
> > Make all of them as overlay (dtso?) but
> >  build dtb by combining them in makefile.
> >
> > This looks the best way because it avoids
> >  redundand code for mmc node and allows
> >  my current spi config (not the status way
> >  which may break due to same unit address).
> >
> > I guess my base dtsi is then a dts too?
>
> Yes, it can be.
>
> >
> > Or should these overlays only duplicated and either include sd dts or emmc dts (but this creates again redundant code)?
> > >> >> --- a/arch/arm64/boot/dts/mediatek/Makefile
> > >> >> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > >> >> @@ -8,6 +8,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> > >> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> > >> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> > >> >>  dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
> > >> >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
> > >> >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
> > >> >
> > >> >These need rules to apply them to the base dtb(s). You just need:
> > >> >
> > >> >full.dtb := base.dtb overlay.dtb
> > >> >dtb-y += full.dtb
> > >>
> > >> I would prefer to do this in bootloader to allow all 4 possible configurations:
> > >>
> > >> Sd+nand
> > >> Sd+nor
> > >> Emmc+nand
> > >> Emmc+nor
> > >
> > >That's fine. The purpose here is to document what the overlays apply
> > >to, check that they actually apply, and validate them when applied
> > >(unless someone wants to figure out all the issues with validating
> > >just an overlay and make that work). You for example have an
> > >undocumented compatible in yours (denx,fit).
> >
> > Oh,need to check,copied partitions from my
> >  uboot dts...maybe there is a linux version
> >  for marking it as fit partition,else i drop
> >  completely.
>
> You just need to document it. But the first thing I'm going to say, is
> 'u-boot' is the vendor, not 'denx'. So 'u-boot,fit'.

imho it is not needed in linux, so i drop it.

regards Frank
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index e8902f2cc58f..d42208c4090d 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -8,6 +8,8 @@  dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-sd.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dts
new file mode 100644
index 000000000000..15ee8c568f3c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nand.dts
@@ -0,0 +1,55 @@ 
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			spi_nand: spi_nand@0 {
+				compatible = "spi-nand";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+				spi-tx-buswidth = <4>;
+				spi-rx-buswidth = <4>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x80000>;
+						read-only;
+					};
+
+					partition@80000 {
+						label = "reserved";
+						reg = <0x80000 0x300000>;
+					};
+
+					partition@380000 {
+						label = "fip";
+						reg = <0x380000 0x200000>;
+						read-only;
+					};
+
+					partition@580000 {
+						label = "ubi";
+						reg = <0x580000 0x7a80000>;
+					};
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dts
new file mode 100644
index 000000000000..f18643a9089c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-nor.dts
@@ -0,0 +1,69 @@ 
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+/*
+ * Authors: Daniel Golle <daniel@makrotopia.org>
+ *          Frank Wunderlich <frank-w@public-files.de>
+ */
+
+/dts-v1/;
+/plugin/;
+
+/ {
+	compatible = "bananapi,bpi-r3", "mediatek,mt7986a";
+
+	fragment@0 {
+		target-path = "/soc/spi@1100a000";
+		__overlay__ {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			flash@0 {
+				compatible = "jedec,spi-nor";
+				reg = <0>;
+				spi-max-frequency = <10000000>;
+
+				partitions {
+					compatible = "fixed-partitions";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					partition@0 {
+						label = "bl2";
+						reg = <0x0 0x20000>;
+						read-only;
+					};
+
+					partition@20000 {
+						label = "reserved";
+						reg = <0x20000 0x20000>;
+					};
+
+					partition@40000 {
+						label = "u-boot-env";
+						reg = <0x40000 0x40000>;
+					};
+
+					partition@80000 {
+						label = "reserved2";
+						reg = <0x80000 0x80000>;
+					};
+
+					partition@100000 {
+						label = "fip";
+						reg = <0x100000 0x80000>;
+						read-only;
+					};
+
+					partition@180000 {
+						label = "recovery";
+						reg = <0x180000 0xa80000>;
+					};
+
+					partition@c00000 {
+						label = "fit";
+						reg = <0xc00000 0x1400000>;
+						compatible = "denx,fit";
+					};
+				};
+			};
+		};
+	};
+};