diff mbox series

[v16,07/22] PCI: dwc: Add outbound MSG TLPs support

Message ID 20230510062234.201499-8-yoshihiro.shimoda.uh@renesas.com (mailing list archive)
State Superseded
Delegated to: Krzysztof Wilczyński
Headers show
Series PCI: rcar-gen4: Add R-Car Gen4 PCIe support | expand

Commit Message

Yoshihiro Shimoda May 10, 2023, 6:22 a.m. UTC 
Add "code" and "routing" into struct dw_pcie_outbound_atu for
sending MSG by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. PCIE_ATU_HEADER_SUB_ENABLE is set to issue the translated
TLP header by using PCIE_ATU_{LOW,UPP}ER_TARGET registers' values.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
---
 drivers/pci/controller/dwc/pcie-designware.c | 7 +++++--
 drivers/pci/controller/dwc/pcie-designware.h | 5 +++++
 2 files changed, 10 insertions(+), 2 deletions(-)

Comments

Serge Semin June 5, 2023, 12:15 a.m. UTC | #1 
On Wed, May 10, 2023 at 03:22:19PM +0900, Yoshihiro Shimoda wrote:
> Add "code" and "routing" into struct dw_pcie_outbound_atu for

structure name has been changed.

> sending MSG by iATU in the PCIe endpoint mode in near the future.
> PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
> MsgD.

So your implementation implies the data-less messages only. This note
should have been added at least to the commit log. Ideally it would be
useful to have an in-situ comment above the code setting these flags.

> PCIE_ATU_HEADER_SUB_ENABLE is set to issue the translated
> TLP header by using PCIE_ATU_{LOW,UPP}ER_TARGET registers' values.

Why is that needed? Please elaborate in the patch log.

Other than that the change looks good.

* I'll get back to the series review tomorrow.

-Serge(y)

> 
> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> ---
>  drivers/pci/controller/dwc/pcie-designware.c | 7 +++++--
>  drivers/pci/controller/dwc/pcie-designware.h | 5 +++++
>  2 files changed, 10 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
> index bd85a73d354b..a7c724ba7385 100644
> --- a/drivers/pci/controller/dwc/pcie-designware.c
> +++ b/drivers/pci/controller/dwc/pcie-designware.c
> @@ -498,7 +498,7 @@ int dw_pcie_prog_outbound_atu(struct dw_pcie *pci,
>  	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_UPPER_TARGET,
>  			      upper_32_bits(atu->pci_addr));
>  
> -	val = atu->type | PCIE_ATU_FUNC_NUM(atu->func_no);
> +	val = atu->type | atu->routing | PCIE_ATU_FUNC_NUM(atu->func_no);
>  	if (upper_32_bits(limit_addr) > upper_32_bits(cpu_addr) &&
>  	    dw_pcie_ver_is_ge(pci, 460A))
>  		val |= PCIE_ATU_INCREASE_REGION_SIZE;
> @@ -506,7 +506,10 @@ int dw_pcie_prog_outbound_atu(struct dw_pcie *pci,
>  		val = dw_pcie_enable_ecrc(val);
>  	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_REGION_CTRL1, val);
>  
> -	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_REGION_CTRL2, PCIE_ATU_ENABLE);
> +	val = PCIE_ATU_ENABLE;
> +	if (atu->type == PCIE_ATU_TYPE_MSG)
> +		val |= PCIE_ATU_INHIBIT_PAYLOAD | PCIE_ATU_HEADER_SUB_ENABLE | atu->code;
> +	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_REGION_CTRL2, val);
>  
>  	/*
>  	 * Make sure ATU enable takes effect before any subsequent config
> diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
> index b8fa099bbed3..c83d1d176e62 100644
> --- a/drivers/pci/controller/dwc/pcie-designware.h
> +++ b/drivers/pci/controller/dwc/pcie-designware.h
> @@ -150,11 +150,14 @@
>  #define PCIE_ATU_TYPE_IO		0x2
>  #define PCIE_ATU_TYPE_CFG0		0x4
>  #define PCIE_ATU_TYPE_CFG1		0x5
> +#define PCIE_ATU_TYPE_MSG		0x10
>  #define PCIE_ATU_TD			BIT(8)
>  #define PCIE_ATU_FUNC_NUM(pf)           ((pf) << 20)
>  #define PCIE_ATU_REGION_CTRL2		0x004
>  #define PCIE_ATU_ENABLE			BIT(31)
>  #define PCIE_ATU_BAR_MODE_ENABLE	BIT(30)
> +#define PCIE_ATU_INHIBIT_PAYLOAD	BIT(22)
> +#define PCIE_ATU_HEADER_SUB_ENABLE	BIT(21)
>  #define PCIE_ATU_FUNC_NUM_MATCH_EN      BIT(19)
>  #define PCIE_ATU_LOWER_BASE		0x008
>  #define PCIE_ATU_UPPER_BASE		0x00C
> @@ -295,6 +298,8 @@ struct dw_pcie_ob_atu_cfg {
>  	int index;
>  	int type;
>  	u8 func_no;
> +	u8 code;
> +	u8 routing;
>  	u64 cpu_addr;
>  	u64 pci_addr;
>  	u64 size;
> -- 
> 2.25.1
>
Yoshihiro Shimoda July 4, 2023, 5:22 a.m. UTC | #2 
Hello Serge,

> From: Serge Semin, Sent: Monday, June 5, 2023 9:16 AM
> 
> On Wed, May 10, 2023 at 03:22:19PM +0900, Yoshihiro Shimoda wrote:
> > Add "code" and "routing" into struct dw_pcie_outbound_atu for
> 
> structure name has been changed.

Oops. I'll fix it.

> > sending MSG by iATU in the PCIe endpoint mode in near the future.
> > PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
> > MsgD.
> 
> So your implementation implies the data-less messages only. This note
> should have been added at least to the commit log. Ideally it would be
> useful to have an in-situ comment above the code setting these flags.

I got it. I'll add such explanation at both the commit log and code.

> > PCIE_ATU_HEADER_SUB_ENABLE is set to issue the translated
> > TLP header by using PCIE_ATU_{LOW,UPP}ER_TARGET registers' values.
> 
> Why is that needed? Please elaborate in the patch log.

Thank you for your comment. I confirmed that this was not needed. So,
I'll drop this comment and related code.

> Other than that the change looks good.

Thank you for your review!

Best regards,
Yoshihiro Shimoda

> * I'll get back to the series review tomorrow.
> 
> -Serge(y)
> 
> >
> > Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> > ---
> >  drivers/pci/controller/dwc/pcie-designware.c | 7 +++++--
> >  drivers/pci/controller/dwc/pcie-designware.h | 5 +++++
> >  2 files changed, 10 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
> > index bd85a73d354b..a7c724ba7385 100644
> > --- a/drivers/pci/controller/dwc/pcie-designware.c
> > +++ b/drivers/pci/controller/dwc/pcie-designware.c
> > @@ -498,7 +498,7 @@ int dw_pcie_prog_outbound_atu(struct dw_pcie *pci,
> >  	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_UPPER_TARGET,
> >  			      upper_32_bits(atu->pci_addr));
> >
> > -	val = atu->type | PCIE_ATU_FUNC_NUM(atu->func_no);
> > +	val = atu->type | atu->routing | PCIE_ATU_FUNC_NUM(atu->func_no);
> >  	if (upper_32_bits(limit_addr) > upper_32_bits(cpu_addr) &&
> >  	    dw_pcie_ver_is_ge(pci, 460A))
> >  		val |= PCIE_ATU_INCREASE_REGION_SIZE;
> > @@ -506,7 +506,10 @@ int dw_pcie_prog_outbound_atu(struct dw_pcie *pci,
> >  		val = dw_pcie_enable_ecrc(val);
> >  	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_REGION_CTRL1, val);
> >
> > -	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_REGION_CTRL2, PCIE_ATU_ENABLE);
> > +	val = PCIE_ATU_ENABLE;
> > +	if (atu->type == PCIE_ATU_TYPE_MSG)
> > +		val |= PCIE_ATU_INHIBIT_PAYLOAD | PCIE_ATU_HEADER_SUB_ENABLE | atu->code;
> > +	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_REGION_CTRL2, val);
> >
> >  	/*
> >  	 * Make sure ATU enable takes effect before any subsequent config
> > diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
> > index b8fa099bbed3..c83d1d176e62 100644
> > --- a/drivers/pci/controller/dwc/pcie-designware.h
> > +++ b/drivers/pci/controller/dwc/pcie-designware.h
> > @@ -150,11 +150,14 @@
> >  #define PCIE_ATU_TYPE_IO		0x2
> >  #define PCIE_ATU_TYPE_CFG0		0x4
> >  #define PCIE_ATU_TYPE_CFG1		0x5
> > +#define PCIE_ATU_TYPE_MSG		0x10
> >  #define PCIE_ATU_TD			BIT(8)
> >  #define PCIE_ATU_FUNC_NUM(pf)           ((pf) << 20)
> >  #define PCIE_ATU_REGION_CTRL2		0x004
> >  #define PCIE_ATU_ENABLE			BIT(31)
> >  #define PCIE_ATU_BAR_MODE_ENABLE	BIT(30)
> > +#define PCIE_ATU_INHIBIT_PAYLOAD	BIT(22)
> > +#define PCIE_ATU_HEADER_SUB_ENABLE	BIT(21)
> >  #define PCIE_ATU_FUNC_NUM_MATCH_EN      BIT(19)
> >  #define PCIE_ATU_LOWER_BASE		0x008
> >  #define PCIE_ATU_UPPER_BASE		0x00C
> > @@ -295,6 +298,8 @@ struct dw_pcie_ob_atu_cfg {
> >  	int index;
> >  	int type;
> >  	u8 func_no;
> > +	u8 code;
> > +	u8 routing;
> >  	u64 cpu_addr;
> >  	u64 pci_addr;
> >  	u64 size;
> > --
> > 2.25.1
> >
diff mbox series

Patch

diff --git a/drivers/pci/controller/dwc/pcie-designware.c b/drivers/pci/controller/dwc/pcie-designware.c
index bd85a73d354b..a7c724ba7385 100644
--- a/drivers/pci/controller/dwc/pcie-designware.c
+++ b/drivers/pci/controller/dwc/pcie-designware.c
@@ -498,7 +498,7 @@  int dw_pcie_prog_outbound_atu(struct dw_pcie *pci,
 	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_UPPER_TARGET,
 			      upper_32_bits(atu->pci_addr));
 
-	val = atu->type | PCIE_ATU_FUNC_NUM(atu->func_no);
+	val = atu->type | atu->routing | PCIE_ATU_FUNC_NUM(atu->func_no);
 	if (upper_32_bits(limit_addr) > upper_32_bits(cpu_addr) &&
 	    dw_pcie_ver_is_ge(pci, 460A))
 		val |= PCIE_ATU_INCREASE_REGION_SIZE;
@@ -506,7 +506,10 @@  int dw_pcie_prog_outbound_atu(struct dw_pcie *pci,
 		val = dw_pcie_enable_ecrc(val);
 	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_REGION_CTRL1, val);
 
-	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_REGION_CTRL2, PCIE_ATU_ENABLE);
+	val = PCIE_ATU_ENABLE;
+	if (atu->type == PCIE_ATU_TYPE_MSG)
+		val |= PCIE_ATU_INHIBIT_PAYLOAD | PCIE_ATU_HEADER_SUB_ENABLE | atu->code;
+	dw_pcie_writel_atu_ob(pci, atu->index, PCIE_ATU_REGION_CTRL2, val);
 
 	/*
 	 * Make sure ATU enable takes effect before any subsequent config
diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
index b8fa099bbed3..c83d1d176e62 100644
--- a/drivers/pci/controller/dwc/pcie-designware.h
+++ b/drivers/pci/controller/dwc/pcie-designware.h
@@ -150,11 +150,14 @@ 
 #define PCIE_ATU_TYPE_IO		0x2
 #define PCIE_ATU_TYPE_CFG0		0x4
 #define PCIE_ATU_TYPE_CFG1		0x5
+#define PCIE_ATU_TYPE_MSG		0x10
 #define PCIE_ATU_TD			BIT(8)
 #define PCIE_ATU_FUNC_NUM(pf)           ((pf) << 20)
 #define PCIE_ATU_REGION_CTRL2		0x004
 #define PCIE_ATU_ENABLE			BIT(31)
 #define PCIE_ATU_BAR_MODE_ENABLE	BIT(30)
+#define PCIE_ATU_INHIBIT_PAYLOAD	BIT(22)
+#define PCIE_ATU_HEADER_SUB_ENABLE	BIT(21)
 #define PCIE_ATU_FUNC_NUM_MATCH_EN      BIT(19)
 #define PCIE_ATU_LOWER_BASE		0x008
 #define PCIE_ATU_UPPER_BASE		0x00C
@@ -295,6 +298,8 @@  struct dw_pcie_ob_atu_cfg {
 	int index;
 	int type;
 	u8 func_no;
+	u8 code;
+	u8 routing;
 	u64 cpu_addr;
 	u64 pci_addr;
 	u64 size;