@@ -16680,6 +16680,13 @@ S: Maintained
F: Documentation/devicetree/bindings/pci/socionext,uniphier-pcie*
F: drivers/pci/controller/dwc/pcie-uniphier*
+PCIE DRIVER FOR STARFIVE JH71x0
+M: Kevin Xie <kevin.xie@starfivetech.com>
+L: linux-pci@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/pci/starfive*
+F: drivers/pci/controller/plda/pcie-starfive.c
+
PCIE DRIVER FOR ST SPEAR13XX
M: Pratyush Anand <pratyush.anand@gmail.com>
L: linux-pci@vger.kernel.org
@@ -15,4 +15,15 @@ config PCIE_MICROCHIP_HOST
Say Y here if you want kernel to support the Microchip AXI PCIe
Host Bridge driver.
+config PCIE_STARFIVE_HOST
+ tristate "StarFive PCIe host controller"
+ depends on OF && PCI_MSI
+ select PCIE_PLDA_HOST
+ help
+ Say Y here if you want to support the StarFive PCIe controller in
+ host mode. StarFive PCIe controller uses PLDA PCIe core.
+
+ If you choose to build this driver as module it will be dynamically
+ linked and module will be called pcie-starfive.ko.
+
endmenu
@@ -1,3 +1,4 @@
# SPDX-License-Identifier: GPL-2.0
obj-$(CONFIG_PCIE_PLDA_HOST) += pcie-plda-host.o
obj-$(CONFIG_PCIE_MICROCHIP_HOST) += pcie-microchip-host.o
+obj-$(CONFIG_PCIE_STARFIVE_HOST) += pcie-starfive.o
@@ -10,10 +10,20 @@
#define PLDA_MAX_NUM_MSI_IRQS 32
/* PCIe Bridge Phy Regs */
+#define GEN_SETTINGS 0x80
+#define RP_ENABLE 1
+#define PCIE_PCI_IDS_DW1 0x9c
+#define IDS_CLASS_CODE_SHIFT 16
+#define REVISION_ID_MASK GENMASK(7, 0)
+#define CLASS_CODE_ID_MASK GENMASK(31, 8)
#define PCIE_PCI_IRQ_DW0 0xa8
#define MSIX_CAP_MASK BIT(31)
#define NUM_MSI_MSGS_MASK GENMASK(6, 4)
#define NUM_MSI_MSGS_SHIFT 4
+#define PCI_MISC 0xb4
+#define PHY_FUNCTION_DIS BIT(15)
+#define PCIE_WINROM 0xfc
+#define PREF_MEM_WIN_64_SUPPORT BIT(3)
#define IMASK_LOCAL 0x180
#define DMA_END_ENGINE_0_MASK 0x00000000u
@@ -66,6 +76,8 @@
#define ISTATUS_HOST 0x18c
#define IMSI_ADDR 0x190
#define ISTATUS_MSI 0x194
+#define PMSG_SUPPORT_RX 0x3f0
+#define PMSG_LTR_SUPPORT BIT(2)
/* PCIe Master table init defines */
#define ATR0_PCIE_WIN0_SRCADDR_PARAM 0x600u
@@ -87,6 +99,8 @@
#define PCIE_TX_RX_INTERFACE 0x00000000u
#define PCIE_CONFIG_INTERFACE 0x00000001u
+#define CONFIG_SPACE_ADDR_OFFSET 0x1000u
+
#define ATR_ENTRY_SIZE 32
#define EVENT_A_ATR_EVT_POST_ERR 0
@@ -194,4 +208,59 @@ static inline void plda_set_default_msi(struct plda_msi *msi)
msi->vector_phy = IMSI_ADDR;
msi->num_vectors = PLDA_MAX_NUM_MSI_IRQS;
}
-#endif
+
+static inline void plda_pcie_enable_root_port(struct plda_pcie_rp *plda)
+{
+ u32 value;
+
+ value = readl_relaxed(plda->bridge_addr + GEN_SETTINGS);
+ value |= RP_ENABLE;
+ writel_relaxed(value, plda->bridge_addr + GEN_SETTINGS);
+}
+
+static inline void plda_pcie_set_standard_class(struct plda_pcie_rp *plda)
+{
+ u32 value;
+
+ /* set class code and reserve revision id */
+ value = readl_relaxed(plda->bridge_addr + PCIE_PCI_IDS_DW1);
+ value &= REVISION_ID_MASK;
+ value |= (PCI_CLASS_BRIDGE_PCI << IDS_CLASS_CODE_SHIFT);
+ writel_relaxed(value, plda->bridge_addr + PCIE_PCI_IDS_DW1);
+}
+
+static inline void plda_pcie_set_pref_win_64bit(struct plda_pcie_rp *plda)
+{
+ u32 value;
+
+ value = readl_relaxed(plda->bridge_addr + PCIE_WINROM);
+ value |= PREF_MEM_WIN_64_SUPPORT;
+ writel_relaxed(value, plda->bridge_addr + PCIE_WINROM);
+}
+
+static inline void plda_pcie_disable_ltr(struct plda_pcie_rp *plda)
+{
+ u32 value;
+
+ value = readl_relaxed(plda->bridge_addr + PMSG_SUPPORT_RX);
+ value &= ~PMSG_LTR_SUPPORT;
+ writel_relaxed(value, plda->bridge_addr + PMSG_SUPPORT_RX);
+}
+
+static inline void plda_pcie_disable_func(struct plda_pcie_rp *plda)
+{
+ u32 value;
+
+ value = readl_relaxed(plda->bridge_addr + PCI_MISC);
+ value |= PHY_FUNCTION_DIS;
+ writel_relaxed(value, plda->bridge_addr + PCI_MISC);
+}
+
+static inline void plda_pcie_write_rc_bar(struct plda_pcie_rp *plda, u64 val)
+{
+ void __iomem *addr = plda->bridge_addr + CONFIG_SPACE_ADDR_OFFSET;
+
+ writel_relaxed(lower_32_bits(val), addr + PCI_BASE_ADDRESS_0);
+ writel_relaxed(upper_32_bits(val), addr + PCI_BASE_ADDRESS_1);
+}
+#endif /* _PCIE_PLDA_H */
new file mode 100644
@@ -0,0 +1,460 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * PCIe host controller driver for StarFive JH7110 Soc.
+ *
+ * Copyright (C) 2023 StarFive Technology Co., Ltd.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+#include <linux/pci.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include "../../pci.h"
+
+#include "pcie-plda.h"
+
+#define PCIE_FUNC_NUM 4
+
+/* system control */
+#define STG_SYSCON_PCIE0_BASE 0x48
+#define STG_SYSCON_PCIE1_BASE 0x1f8
+
+#define STG_SYSCON_AR_OFFSET 0x78
+#define STG_SYSCON_AXI4_SLVL_AR_MASK GENMASK(22, 8)
+#define STG_SYSCON_AXI4_SLVL_PHY_AR(x) FIELD_PREP(GENMASK(20, 17), x)
+#define STG_SYSCON_AW_OFFSET 0x7c
+#define STG_SYSCON_AXI4_SLVL_AW_MASK GENMASK(14, 0)
+#define STG_SYSCON_AXI4_SLVL_PHY_AW(x) FIELD_PREP(GENMASK(12, 9), x)
+#define STG_SYSCON_CLKREQ BIT(22)
+#define STG_SYSCON_CKREF_SRC_MASK GENMASK(19, 18)
+#define STG_SYSCON_RP_NEP_OFFSET 0xe8
+#define STG_SYSCON_K_RP_NEP BIT(8)
+#define STG_SYSCON_LNKSTA_OFFSET 0x170
+#define DATA_LINK_ACTIVE BIT(5)
+
+/* Parameters for the waiting for link up routine */
+#define LINK_WAIT_MAX_RETRIES 10
+#define LINK_WAIT_USLEEP_MIN 90000
+#define LINK_WAIT_USLEEP_MAX 100000
+
+struct starfive_jh7110_pcie {
+ struct plda_pcie_rp plda;
+ struct reset_control *resets;
+ struct clk_bulk_data *clks;
+ struct regmap *reg_syscon;
+ struct gpio_desc *power_gpio;
+ struct gpio_desc *reset_gpio;
+ struct phy *phy;
+
+ unsigned int stg_pcie_base;
+ int num_clks;
+};
+
+/*
+ * The BAR0/1 of bridge should be hidden during enumeration to
+ * avoid the sizing and resource allocation by PCIe core.
+ */
+static bool starfive_pcie_hide_rc_bar(struct pci_bus *bus, unsigned int devfn,
+ int offset)
+{
+ if (pci_is_root_bus(bus) && !devfn &&
+ (offset == PCI_BASE_ADDRESS_0 || offset == PCI_BASE_ADDRESS_1))
+ return true;
+
+ return false;
+}
+
+static int starfive_pcie_config_write(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 value)
+{
+ if (starfive_pcie_hide_rc_bar(bus, devfn, where))
+ return PCIBIOS_SUCCESSFUL;
+
+ return pci_generic_config_write(bus, devfn, where, size, value);
+}
+
+static int starfive_pcie_config_read(struct pci_bus *bus, unsigned int devfn,
+ int where, int size, u32 *value)
+{
+ if (starfive_pcie_hide_rc_bar(bus, devfn, where)) {
+ *value = 0;
+ return PCIBIOS_SUCCESSFUL;
+ }
+
+ return pci_generic_config_read(bus, devfn, where, size, value);
+}
+
+static int starfive_pcie_parse_dt(struct starfive_jh7110_pcie *pcie,
+ struct device *dev)
+{
+ int domain_nr;
+
+ pcie->num_clks = devm_clk_bulk_get_all(dev, &pcie->clks);
+ if (pcie->num_clks < 0)
+ return dev_err_probe(dev, -ENODEV,
+ "failed to get pcie clocks\n");
+
+ pcie->resets = devm_reset_control_array_get_exclusive(dev);
+ if (IS_ERR(pcie->resets))
+ return dev_err_probe(dev, PTR_ERR(pcie->resets),
+ "failed to get pcie resets");
+
+ pcie->reg_syscon =
+ syscon_regmap_lookup_by_phandle(dev->of_node,
+ "starfive,stg-syscon");
+
+ if (IS_ERR(pcie->reg_syscon))
+ return dev_err_probe(dev, PTR_ERR(pcie->reg_syscon),
+ "failed to parse starfive,stg-syscon\n");
+
+ pcie->phy = devm_phy_optional_get(dev, NULL);
+ if (IS_ERR(pcie->phy))
+ return dev_err_probe(dev, PTR_ERR(pcie->phy),
+ "failed to get pcie phy\n");
+
+ domain_nr = of_get_pci_domain_nr(dev->of_node);
+
+ if (domain_nr < 0 || domain_nr > 1)
+ return dev_err_probe(dev, -ENODEV,
+ "failed to get valid pcie domain\n");
+
+ if (domain_nr == 0)
+ pcie->stg_pcie_base = STG_SYSCON_PCIE0_BASE;
+ else
+ pcie->stg_pcie_base = STG_SYSCON_PCIE1_BASE;
+
+ pcie->reset_gpio = devm_gpiod_get_optional(dev, "perst",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(pcie->reset_gpio))
+ return dev_err_probe(dev, PTR_ERR(pcie->reset_gpio),
+ "failed to get perst-gpio\n");
+
+ pcie->power_gpio = devm_gpiod_get_optional(dev, "enable",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(pcie->power_gpio))
+ return dev_err_probe(dev, PTR_ERR(pcie->power_gpio),
+ "failed to get power-gpio\n");
+
+ return 0;
+}
+
+static struct pci_ops starfive_pcie_ops = {
+ .map_bus = plda_pcie_map_bus,
+ .read = starfive_pcie_config_read,
+ .write = starfive_pcie_config_write,
+};
+
+static int starfive_pcie_clk_rst_init(struct starfive_jh7110_pcie *pcie)
+{
+ struct device *dev = pcie->plda.dev;
+ int ret;
+
+ ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to enable clocks\n");
+
+ ret = reset_control_deassert(pcie->resets);
+ if (ret) {
+ clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
+ dev_err_probe(dev, ret, "failed to deassert resets\n");
+ }
+
+ return ret;
+}
+
+static void starfive_pcie_clk_rst_deinit(struct starfive_jh7110_pcie *pcie)
+{
+ reset_control_assert(pcie->resets);
+ clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
+}
+
+static bool starfive_pcie_link_up(struct plda_pcie_rp *plda)
+{
+ struct starfive_jh7110_pcie *pcie =
+ container_of(plda, struct starfive_jh7110_pcie, plda);
+ int ret;
+ u32 stg_reg_val;
+
+ ret = regmap_read(pcie->reg_syscon,
+ pcie->stg_pcie_base + STG_SYSCON_LNKSTA_OFFSET,
+ &stg_reg_val);
+ if (ret) {
+ dev_err(pcie->plda.dev, "failed to read link status\n");
+ return false;
+ }
+
+ return !!(stg_reg_val & DATA_LINK_ACTIVE);
+}
+
+static int starfive_pcie_host_wait_for_link(struct starfive_jh7110_pcie *pcie)
+{
+ int retries;
+
+ /* Check if the link is up or not */
+ for (retries = 0; retries < LINK_WAIT_MAX_RETRIES; retries++) {
+ if (starfive_pcie_link_up(&pcie->plda)) {
+ dev_info(pcie->plda.dev, "port link up\n");
+ return 0;
+ }
+ usleep_range(LINK_WAIT_USLEEP_MIN, LINK_WAIT_USLEEP_MAX);
+ }
+
+ return -ETIMEDOUT;
+}
+
+static int starfive_pcie_enable_phy(struct device *dev,
+ struct starfive_jh7110_pcie *pcie)
+{
+ int ret;
+
+ if (!pcie->phy)
+ return 0;
+
+ ret = phy_init(pcie->phy);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "failed to initialize pcie phy\n");
+
+ ret = phy_set_mode(pcie->phy, PHY_MODE_PCIE);
+ if (ret) {
+ dev_err_probe(dev, ret, "failed to set pcie mode\n");
+ goto err_phy_on;
+ }
+
+ ret = phy_power_on(pcie->phy);
+ if (ret) {
+ dev_err_probe(dev, ret, "failed to power on pcie phy\n");
+ goto err_phy_on;
+ }
+
+ return 0;
+
+err_phy_on:
+ phy_exit(pcie->phy);
+ return ret;
+}
+
+static void starfive_pcie_disable_phy(struct starfive_jh7110_pcie *pcie)
+{
+ phy_power_off(pcie->phy);
+ phy_exit(pcie->phy);
+}
+
+static void starfive_pcie_host_deinit(struct plda_pcie_rp *plda)
+{
+ struct starfive_jh7110_pcie *pcie =
+ container_of(plda, struct starfive_jh7110_pcie, plda);
+
+ starfive_pcie_clk_rst_deinit(pcie);
+ if (pcie->power_gpio)
+ gpiod_set_value_cansleep(pcie->power_gpio, 0);
+ starfive_pcie_disable_phy(pcie);
+}
+
+static int starfive_pcie_host_init(struct plda_pcie_rp *plda)
+{
+ struct starfive_jh7110_pcie *pcie =
+ container_of(plda, struct starfive_jh7110_pcie, plda);
+ struct device *dev = plda->dev;
+ int ret;
+ int i;
+
+ ret = starfive_pcie_enable_phy(dev, pcie);
+ if (ret)
+ return ret;
+
+ regmap_update_bits(pcie->reg_syscon,
+ pcie->stg_pcie_base + STG_SYSCON_RP_NEP_OFFSET,
+ STG_SYSCON_K_RP_NEP, STG_SYSCON_K_RP_NEP);
+
+ regmap_update_bits(pcie->reg_syscon,
+ pcie->stg_pcie_base + STG_SYSCON_AW_OFFSET,
+ STG_SYSCON_CKREF_SRC_MASK,
+ FIELD_PREP(STG_SYSCON_CKREF_SRC_MASK, 2));
+
+ regmap_update_bits(pcie->reg_syscon,
+ pcie->stg_pcie_base + STG_SYSCON_AW_OFFSET,
+ STG_SYSCON_CLKREQ, STG_SYSCON_CLKREQ);
+
+ ret = starfive_pcie_clk_rst_init(pcie);
+ if (ret)
+ return ret;
+
+ if (pcie->power_gpio)
+ gpiod_set_value_cansleep(pcie->power_gpio, 1);
+
+ if (pcie->reset_gpio)
+ gpiod_set_value_cansleep(pcie->reset_gpio, 1);
+
+ /* Disable physical functions except #0 */
+ for (i = 1; i < PCIE_FUNC_NUM; i++) {
+ regmap_update_bits(pcie->reg_syscon,
+ pcie->stg_pcie_base + STG_SYSCON_AR_OFFSET,
+ STG_SYSCON_AXI4_SLVL_AR_MASK,
+ STG_SYSCON_AXI4_SLVL_PHY_AR(i));
+
+ regmap_update_bits(pcie->reg_syscon,
+ pcie->stg_pcie_base + STG_SYSCON_AW_OFFSET,
+ STG_SYSCON_AXI4_SLVL_AW_MASK,
+ STG_SYSCON_AXI4_SLVL_PHY_AW(i));
+
+ plda_pcie_disable_func(plda);
+ }
+
+ regmap_update_bits(pcie->reg_syscon,
+ pcie->stg_pcie_base + STG_SYSCON_AR_OFFSET,
+ STG_SYSCON_AXI4_SLVL_AR_MASK, 0);
+ regmap_update_bits(pcie->reg_syscon,
+ pcie->stg_pcie_base + STG_SYSCON_AW_OFFSET,
+ STG_SYSCON_AXI4_SLVL_AW_MASK, 0);
+
+ plda_pcie_enable_root_port(plda);
+ plda_pcie_write_rc_bar(plda, 0);
+
+ /* PCIe PCI Standard Configuration Identification Settings. */
+ plda_pcie_set_standard_class(plda);
+
+ /*
+ * The LTR message forwarding of PCIe Message Reception was set by core
+ * as default, but the forward id & addr are also need to be reset.
+ * If we do not disable LTR message forwarding here, or set a legal
+ * forwarding address, the kernel will get stuck after the driver probe.
+ * To workaround, disable the LTR message forwarding support on
+ * PCIe Message Reception.
+ */
+ plda_pcie_disable_ltr(plda);
+
+ /* Prefetchable memory window 64-bit addressing support */
+ plda_pcie_set_pref_win_64bit(plda);
+
+ /*
+ * Ensure that PERST has been asserted for at least 100 ms,
+ * the sleep value is T_PVPERL from PCIe CEM spec r2.0 (Table 2-4)
+ */
+ msleep(100);
+ if (pcie->reset_gpio)
+ gpiod_set_value_cansleep(pcie->reset_gpio, 0);
+
+ /*
+ * With a Downstream Port (<=5GT/s), software must wait a minimum
+ * of 100ms following exit from a conventional reset before
+ * sending a configuration request to the device.
+ */
+ msleep(PCIE_BEFORE_CONFIG_REQUEST_WAIT_MS);
+
+ if (starfive_pcie_host_wait_for_link(pcie))
+ dev_info(dev, "port link down\n");
+
+ return 0;
+}
+
+static const struct plda_pcie_host_ops sf_host_ops = {
+ .host_init = starfive_pcie_host_init,
+ .host_deinit = starfive_pcie_host_deinit,
+};
+
+static int starfive_pcie_probe(struct platform_device *pdev)
+{
+ struct starfive_jh7110_pcie *pcie;
+ struct device *dev = &pdev->dev;
+ struct plda_pcie_rp *plda;
+ int ret;
+
+ pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+ if (!pcie)
+ return -ENOMEM;
+
+ plda = &pcie->plda;
+ plda->dev = dev;
+
+ ret = starfive_pcie_parse_dt(pcie, dev);
+ if (ret)
+ return ret;
+
+ plda->host_ops = &sf_host_ops;
+ plda->num_events = NUM_PLDA_EVENTS;
+ ret = plda_pcie_host_init(&pcie->plda, &starfive_pcie_ops);
+ if (ret)
+ return ret;
+
+ pm_runtime_enable(&pdev->dev);
+ pm_runtime_get_sync(&pdev->dev);
+ platform_set_drvdata(pdev, pcie);
+
+ return 0;
+}
+
+static void starfive_pcie_remove(struct platform_device *pdev)
+{
+ struct starfive_jh7110_pcie *pcie = platform_get_drvdata(pdev);
+
+ plda_pcie_host_deinit(&pcie->plda);
+ platform_set_drvdata(pdev, NULL);
+}
+
+static int starfive_pcie_suspend_noirq(struct device *dev)
+{
+ struct starfive_jh7110_pcie *pcie = dev_get_drvdata(dev);
+
+ clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
+ starfive_pcie_disable_phy(pcie);
+
+ return 0;
+}
+
+static int starfive_pcie_resume_noirq(struct device *dev)
+{
+ struct starfive_jh7110_pcie *pcie = dev_get_drvdata(dev);
+ int ret;
+
+ ret = starfive_pcie_enable_phy(dev, pcie);
+ if (ret)
+ return ret;
+
+ ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
+ if (ret) {
+ dev_err(dev, "failed to enable clocks\n");
+ starfive_pcie_disable_phy(pcie);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct dev_pm_ops starfive_pcie_pm_ops = {
+ NOIRQ_SYSTEM_SLEEP_PM_OPS(starfive_pcie_suspend_noirq,
+ starfive_pcie_resume_noirq)
+};
+
+static const struct of_device_id starfive_pcie_of_match[] = {
+ { .compatible = "starfive,jh7110-pcie", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, starfive_pcie_of_match);
+
+static struct platform_driver starfive_pcie_driver = {
+ .driver = {
+ .name = "pcie-starfive",
+ .of_match_table = of_match_ptr(starfive_pcie_of_match),
+ .pm = pm_sleep_ptr(&starfive_pcie_pm_ops),
+ },
+ .probe = starfive_pcie_probe,
+ .remove_new = starfive_pcie_remove,
+};
+module_platform_driver(starfive_pcie_driver);
+
+MODULE_DESCRIPTION("StarFive JH7110 PCIe host driver");
+MODULE_LICENSE("GPL v2");
@@ -19,6 +19,13 @@
*/
#define PCIE_PME_TO_L2_TIMEOUT_US 10000
+/*
+ * PCIe r6.0, sec 6.6.1, <Conventional Reset>
+ * Requires a minimum waiting of 100ms before sending a configuration
+ * request to the device.
+ */
+#define PCIE_BEFORE_CONFIG_REQUEST_WAIT_MS 100
+
extern const unsigned char pcie_link_speed[];
extern bool pci_early_dump;