| Message ID | 20231222122901.49538-8-ilpo.jarvinen@linux.intel.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | PCI: Solve two bridge window sizing issues | expand |
On Fri, Dec 22, 2023 at 02:29:01PM +0200, Ilpo Järvinen wrote: > During remove & rescan cycle, PCI subsystem will recalculate and adjust > the bridge window sizing that was initially done by "BIOS". The size > calculation is based on the required alignment of the largest resource > among the downstream resources as per pbus_size_mem() (unimportant or > zero parameters marked with "..."): > > min_align = calculate_mem_align(aligns, max_order); > size0 = calculate_memsize(size, ..., min_align); > > and then in calculate_memsize(): > size = ALIGN(max(size, ...) + ..., align); > > If the original bridge window sizing tried to conserve space, this will > lead to massive increase of the required bridge window size when the > downstream has a large disparity in BAR sizes. E.g., with 16MiB and > 16GiB BARs this results in 32GiB bridge window size even if 16MiB BAR > does not require gigabytes of space to fit. > > When doing remove & rescan for a bus that contains such a PCI device, a > larger bridge window is suddenly required on rescan but when there is a > bridge window upstream that is already assigned based on the original > size, it cannot be enlarged to the new requirement. This causes the > allocation of the bridge window to fail (0x600000000 > 0x400ffffff): > > pci 0000:02:01.0: PCI bridge to [bus 03] > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > pci 0000:01:00.0: PCI bridge to [bus 02-04] > pci 0000:01:00.0: bridge window [mem 0x40400000-0x406fffff] > pci 0000:01:00.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > ... > pci_bus 0000:03: busn_res: [bus 03] is released > pci 0000:03:00.0: reg 0x10: [mem 0x6400000000-0x6400ffffff 64bit pref] > pci 0000:03:00.0: reg 0x18: [mem 0x6000000000-0x63ffffffff 64bit pref] > pci 0000:03:00.0: reg 0x30: [mem 0x40400000-0x405fffff pref] > pci 0000:02:01.0: PCI bridge to [bus 03] > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > pci 0000:02:01.0: BAR 9: no space for [mem size 0x600000000 64bit pref] > pci 0000:02:01.0: BAR 9: failed to assign [mem size 0x600000000 64bit pref] > pci 0000:02:01.0: BAR 8: assigned [mem 0x40400000-0x405fffff] > pci 0000:03:00.0: BAR 2: no space for [mem size 0x400000000 64bit pref] > pci 0000:03:00.0: BAR 2: failed to assign [mem size 0x400000000 64bit pref] > pci 0000:03:00.0: BAR 0: no space for [mem size 0x01000000 64bit pref] > pci 0000:03:00.0: BAR 0: failed to assign [mem size 0x01000000 64bit pref] > pci 0000:03:00.0: BAR 6: assigned [mem 0x40400000-0x405fffff pref] > pci 0000:02:01.0: PCI bridge to [bus 03] > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > > This is a major surprise for users who are suddenly left with a PCIe > device that was working fine with the original bridge window sizing. > > Even if the already assigned bridge window could be enlarged by > reallocation in some cases (something the current code does not attempt > to do), it is not possible in general case and the large amount of > wasted space at the tail of the bridge window may lead to other > resource exhaustion problems on Root Complex level (think of multiple > PCIe cards with VFs and BAR size disparity in a single system). > > PCI specifications only expect natural alignment for BARs (PCI Express > Base Specification, rev. 6.1 sect. 7.5.1.2.1) and minimum of 1MiB > alignment for the bridge window (PCI Express Base Specification, > rev 6.1 sect. 7.5.1.3). The current bridge window tail alignment rule > was introduced in the commit 5d0a8965aea9 ("[PATCH] 2.5.14: New PCI > allocation code (alpha, arm, parisc) [2/2]") that only states: > "pbus_size_mem: core stuff; tested with randomly generated sets of > resources". It does not explain the motivation for the extra tail space > allocated that is not truly needed by the downstream resources. As > such, it is far from clear if it ever has been required by any HW. > > To prevent PCIe cards with BAR size disparity from becoming unusable > after remove & rescan cycle, attempt to do a truly minimal allocation > for memory resources if needed. First check if the normally calculated > bridge window will not fit into an already assigned upstream resource. > In such case, try with relaxed bridge window tail sizing rules instead > where no extra tail space is requested beyond what the downstream > resources require. Only enforce the alignment requirement of the bridge > window itself (normally 1MiB). > > With this patch, the resources are successfully allocated: > > pci 0000:02:01.0: PCI bridge to [bus 03] > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] to [bus 03] requires relaxed alignment rules > pci 0000:02:01.0: BAR 9: assigned [mem 0x6000000000-0x6400ffffff 64bit pref] > pci 0000:02:01.0: BAR 8: assigned [mem 0x40400000-0x405fffff] > pci 0000:03:00.0: BAR 2: assigned [mem 0x6000000000-0x63ffffffff 64bit pref] > pci 0000:03:00.0: BAR 0: assigned [mem 0x6400000000-0x6400ffffff 64bit pref] > pci 0000:03:00.0: BAR 6: assigned [mem 0x40400000-0x405fffff pref] > pci 0000:02:01.0: PCI bridge to [bus 03] > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > > This patch draws inspiration from the initial investigations and work > by Mika Westerberg. ... > + struct resource_constraint constraint = { .max = (resource_size_t)~0ULL, RESOURCE_SIZE_MAX from limits.h. > + .align = align }; Also I prefer the style struct resource_constraint constraint = { .max = RESOURCE_SIZE_MAX, .align = align, }; ... > + if (!r || r == &ioport_resource || r == &iomem_resource) > + continue; > + if (!r->parent || (r->flags & mask) != type) Thinking more about these checks, r->parent should be NULL for the root resources, hence this check basically covers the second part of the above. But like you said it's a material for a separate investigation. > + continue; ... > + pci_dbg(bus->self, > + "Assigned bridge window %pR to %pR cannot fit 0x%llx required for %s bridging to %pR\n", > + r, &bus->busn_res, > + (unsigned long long)size, Yeah, casting here is a compromise between good looking message and kernel code. > + pci_name(downstream->self), > + &downstream->busn_res); > + } ... > + pbus_upstream_assigned_limit(bus, mask | IORESOURCE_PREFETCH, type, > + size0, add_align)) { One line? ... > + size0 = calculate_memsize(size, min_size, 0, 0, > + resource_size(b_res), win_align); One line?
On Fri, 22 Dec 2023, Andy Shevchenko wrote: > On Fri, Dec 22, 2023 at 02:29:01PM +0200, Ilpo Järvinen wrote: > > During remove & rescan cycle, PCI subsystem will recalculate and adjust > > the bridge window sizing that was initially done by "BIOS". The size > > calculation is based on the required alignment of the largest resource > > among the downstream resources as per pbus_size_mem() (unimportant or > > zero parameters marked with "..."): > > > > min_align = calculate_mem_align(aligns, max_order); > > size0 = calculate_memsize(size, ..., min_align); > > > > and then in calculate_memsize(): > > size = ALIGN(max(size, ...) + ..., align); > > > > If the original bridge window sizing tried to conserve space, this will > > lead to massive increase of the required bridge window size when the > > downstream has a large disparity in BAR sizes. E.g., with 16MiB and > > 16GiB BARs this results in 32GiB bridge window size even if 16MiB BAR > > does not require gigabytes of space to fit. > > > > When doing remove & rescan for a bus that contains such a PCI device, a > > larger bridge window is suddenly required on rescan but when there is a > > bridge window upstream that is already assigned based on the original > > size, it cannot be enlarged to the new requirement. This causes the > > allocation of the bridge window to fail (0x600000000 > 0x400ffffff): > > > > pci 0000:02:01.0: PCI bridge to [bus 03] > > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > > pci 0000:01:00.0: PCI bridge to [bus 02-04] > > pci 0000:01:00.0: bridge window [mem 0x40400000-0x406fffff] > > pci 0000:01:00.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > > ... > > pci_bus 0000:03: busn_res: [bus 03] is released > > pci 0000:03:00.0: reg 0x10: [mem 0x6400000000-0x6400ffffff 64bit pref] > > pci 0000:03:00.0: reg 0x18: [mem 0x6000000000-0x63ffffffff 64bit pref] > > pci 0000:03:00.0: reg 0x30: [mem 0x40400000-0x405fffff pref] > > pci 0000:02:01.0: PCI bridge to [bus 03] > > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > > pci 0000:02:01.0: BAR 9: no space for [mem size 0x600000000 64bit pref] > > pci 0000:02:01.0: BAR 9: failed to assign [mem size 0x600000000 64bit pref] > > pci 0000:02:01.0: BAR 8: assigned [mem 0x40400000-0x405fffff] > > pci 0000:03:00.0: BAR 2: no space for [mem size 0x400000000 64bit pref] > > pci 0000:03:00.0: BAR 2: failed to assign [mem size 0x400000000 64bit pref] > > pci 0000:03:00.0: BAR 0: no space for [mem size 0x01000000 64bit pref] > > pci 0000:03:00.0: BAR 0: failed to assign [mem size 0x01000000 64bit pref] > > pci 0000:03:00.0: BAR 6: assigned [mem 0x40400000-0x405fffff pref] > > pci 0000:02:01.0: PCI bridge to [bus 03] > > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > > > > This is a major surprise for users who are suddenly left with a PCIe > > device that was working fine with the original bridge window sizing. > > > > Even if the already assigned bridge window could be enlarged by > > reallocation in some cases (something the current code does not attempt > > to do), it is not possible in general case and the large amount of > > wasted space at the tail of the bridge window may lead to other > > resource exhaustion problems on Root Complex level (think of multiple > > PCIe cards with VFs and BAR size disparity in a single system). > > > > PCI specifications only expect natural alignment for BARs (PCI Express > > Base Specification, rev. 6.1 sect. 7.5.1.2.1) and minimum of 1MiB > > alignment for the bridge window (PCI Express Base Specification, > > rev 6.1 sect. 7.5.1.3). The current bridge window tail alignment rule > > was introduced in the commit 5d0a8965aea9 ("[PATCH] 2.5.14: New PCI > > allocation code (alpha, arm, parisc) [2/2]") that only states: > > "pbus_size_mem: core stuff; tested with randomly generated sets of > > resources". It does not explain the motivation for the extra tail space > > allocated that is not truly needed by the downstream resources. As > > such, it is far from clear if it ever has been required by any HW. > > > > To prevent PCIe cards with BAR size disparity from becoming unusable > > after remove & rescan cycle, attempt to do a truly minimal allocation > > for memory resources if needed. First check if the normally calculated > > bridge window will not fit into an already assigned upstream resource. > > In such case, try with relaxed bridge window tail sizing rules instead > > where no extra tail space is requested beyond what the downstream > > resources require. Only enforce the alignment requirement of the bridge > > window itself (normally 1MiB). > > > > With this patch, the resources are successfully allocated: > > > > pci 0000:02:01.0: PCI bridge to [bus 03] > > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] to [bus 03] requires relaxed alignment rules > > pci 0000:02:01.0: BAR 9: assigned [mem 0x6000000000-0x6400ffffff 64bit pref] > > pci 0000:02:01.0: BAR 8: assigned [mem 0x40400000-0x405fffff] > > pci 0000:03:00.0: BAR 2: assigned [mem 0x6000000000-0x63ffffffff 64bit pref] > > pci 0000:03:00.0: BAR 0: assigned [mem 0x6400000000-0x6400ffffff 64bit pref] > > pci 0000:03:00.0: BAR 6: assigned [mem 0x40400000-0x405fffff pref] > > pci 0000:02:01.0: PCI bridge to [bus 03] > > pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] > > pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] > > > > This patch draws inspiration from the initial investigations and work > > by Mika Westerberg. > > + if (!r || r == &ioport_resource || r == &iomem_resource) > > + continue; > > > + if (!r->parent || (r->flags & mask) != type) > > Thinking more about these checks, r->parent should be NULL for the root > resources, hence this check basically covers the second part of the above. > > But like you said it's a material for a separate investigation. This new argument, however, is more convincing than the one you presented earlier. It is indeed true that even if we'd somehow end up into one of those root resources, its ->parent should be NULL (which differentiates this code from the other function which doesn't have similar ->parent check). Also, the code has evolved to stop at the Root Port so it's another thing which should prevent even reaching that far. > > + pbus_upstream_assigned_limit(bus, mask | IORESOURCE_PREFETCH, type, > > + size0, add_align)) { > > One line? I don't think so, 101 chars.
diff --git a/drivers/pci/setup-bus.c b/drivers/pci/setup-bus.c index e3e6ff8854a7..cafc43a1512d 100644 --- a/drivers/pci/setup-bus.c +++ b/drivers/pci/setup-bus.c @@ -960,6 +960,63 @@ static inline resource_size_t calculate_mem_align(resource_size_t *aligns, return min_align; } +/** + * pbus_upstream_assigned_limit - Check no upstream resource limits allocation + * @bus: The bus + * @mask: Mask the resource flag, then compare it with type + * @type: The type of resource from bridge + * @size: The size required from the bridge window + * @align: Required alignment for the resource + * + * Checks that @size can fit inside the upstream bridge resources that are + * already assigned. + * + * Return: -ENOSPC if @size cannot fit into an already assigned resource + * upstream resource. + */ +static int pbus_upstream_assigned_limit(struct pci_bus *bus, unsigned long mask, + unsigned long type, resource_size_t size, + resource_size_t align) +{ + struct resource_constraint constraint = { .max = (resource_size_t)~0ULL, + .align = align }; + struct pci_bus *downstream = bus; + struct resource *r; + + while ((bus = bus->parent)) { + if (pci_is_root_bus(bus)) + break; + + pci_bus_for_each_resource(bus, r) { + if (!r || r == &ioport_resource || r == &iomem_resource) + continue; + + if (!r->parent || (r->flags & mask) != type) + continue; + + if (resource_size(r) >= size) { + struct resource gap = {}; + + if (!find_empty_resource_slot(r, &gap, size, &constraint)) + return 0; + } + + if (bus->self) { + pci_dbg(bus->self, + "Assigned bridge window %pR to %pR cannot fit 0x%llx required for %s bridging to %pR\n", + r, &bus->busn_res, + (unsigned long long)size, + pci_name(downstream->self), + &downstream->busn_res); + } + + return -ENOSPC; + } + } + + return 0; +} + /** * pbus_size_mem() - Size the memory window of a given bus * @@ -986,7 +1043,7 @@ static int pbus_size_mem(struct pci_bus *bus, unsigned long mask, struct list_head *realloc_head) { struct pci_dev *dev; - resource_size_t min_align, align, size, size0, size1; + resource_size_t min_align, win_align, align, size, size0, size1; resource_size_t aligns[24]; /* Alignments from 1MB to 8TB */ int order, max_order; struct resource *b_res = find_bus_resource_of_type(bus, @@ -1064,10 +1121,24 @@ static int pbus_size_mem(struct pci_bus *bus, unsigned long mask, } } + win_align = window_alignment(bus, b_res->flags); min_align = calculate_mem_align(aligns, max_order); - min_align = max(min_align, window_alignment(bus, b_res->flags)); + min_align = max(min_align, win_align); size0 = calculate_memsize(size, min_size, 0, 0, resource_size(b_res), min_align); add_align = max(min_align, add_align); + + if (bus->self && size0 && + pbus_upstream_assigned_limit(bus, mask | IORESOURCE_PREFETCH, type, + size0, add_align)) { + min_align = 1ULL << (max_order + 20); + min_align = max(min_align, win_align); + size0 = calculate_memsize(size, min_size, 0, 0, + resource_size(b_res), win_align); + add_align = win_align; + pci_info(bus->self, "bridge window %pR to %pR requires relaxed alignment rules\n", + b_res, &bus->busn_res); + } + size1 = (!realloc_head || (realloc_head && !add_size && !children_add_size)) ? size0 : calculate_memsize(size, min_size, add_size, children_add_size, resource_size(b_res), add_align);
During remove & rescan cycle, PCI subsystem will recalculate and adjust the bridge window sizing that was initially done by "BIOS". The size calculation is based on the required alignment of the largest resource among the downstream resources as per pbus_size_mem() (unimportant or zero parameters marked with "..."): min_align = calculate_mem_align(aligns, max_order); size0 = calculate_memsize(size, ..., min_align); and then in calculate_memsize(): size = ALIGN(max(size, ...) + ..., align); If the original bridge window sizing tried to conserve space, this will lead to massive increase of the required bridge window size when the downstream has a large disparity in BAR sizes. E.g., with 16MiB and 16GiB BARs this results in 32GiB bridge window size even if 16MiB BAR does not require gigabytes of space to fit. When doing remove & rescan for a bus that contains such a PCI device, a larger bridge window is suddenly required on rescan but when there is a bridge window upstream that is already assigned based on the original size, it cannot be enlarged to the new requirement. This causes the allocation of the bridge window to fail (0x600000000 > 0x400ffffff): pci 0000:02:01.0: PCI bridge to [bus 03] pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] pci 0000:01:00.0: PCI bridge to [bus 02-04] pci 0000:01:00.0: bridge window [mem 0x40400000-0x406fffff] pci 0000:01:00.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] ... pci_bus 0000:03: busn_res: [bus 03] is released pci 0000:03:00.0: reg 0x10: [mem 0x6400000000-0x6400ffffff 64bit pref] pci 0000:03:00.0: reg 0x18: [mem 0x6000000000-0x63ffffffff 64bit pref] pci 0000:03:00.0: reg 0x30: [mem 0x40400000-0x405fffff pref] pci 0000:02:01.0: PCI bridge to [bus 03] pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] pci 0000:02:01.0: BAR 9: no space for [mem size 0x600000000 64bit pref] pci 0000:02:01.0: BAR 9: failed to assign [mem size 0x600000000 64bit pref] pci 0000:02:01.0: BAR 8: assigned [mem 0x40400000-0x405fffff] pci 0000:03:00.0: BAR 2: no space for [mem size 0x400000000 64bit pref] pci 0000:03:00.0: BAR 2: failed to assign [mem size 0x400000000 64bit pref] pci 0000:03:00.0: BAR 0: no space for [mem size 0x01000000 64bit pref] pci 0000:03:00.0: BAR 0: failed to assign [mem size 0x01000000 64bit pref] pci 0000:03:00.0: BAR 6: assigned [mem 0x40400000-0x405fffff pref] pci 0000:02:01.0: PCI bridge to [bus 03] pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] This is a major surprise for users who are suddenly left with a PCIe device that was working fine with the original bridge window sizing. Even if the already assigned bridge window could be enlarged by reallocation in some cases (something the current code does not attempt to do), it is not possible in general case and the large amount of wasted space at the tail of the bridge window may lead to other resource exhaustion problems on Root Complex level (think of multiple PCIe cards with VFs and BAR size disparity in a single system). PCI specifications only expect natural alignment for BARs (PCI Express Base Specification, rev. 6.1 sect. 7.5.1.2.1) and minimum of 1MiB alignment for the bridge window (PCI Express Base Specification, rev 6.1 sect. 7.5.1.3). The current bridge window tail alignment rule was introduced in the commit 5d0a8965aea9 ("[PATCH] 2.5.14: New PCI allocation code (alpha, arm, parisc) [2/2]") that only states: "pbus_size_mem: core stuff; tested with randomly generated sets of resources". It does not explain the motivation for the extra tail space allocated that is not truly needed by the downstream resources. As such, it is far from clear if it ever has been required by any HW. To prevent PCIe cards with BAR size disparity from becoming unusable after remove & rescan cycle, attempt to do a truly minimal allocation for memory resources if needed. First check if the normally calculated bridge window will not fit into an already assigned upstream resource. In such case, try with relaxed bridge window tail sizing rules instead where no extra tail space is requested beyond what the downstream resources require. Only enforce the alignment requirement of the bridge window itself (normally 1MiB). With this patch, the resources are successfully allocated: pci 0000:02:01.0: PCI bridge to [bus 03] pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] to [bus 03] requires relaxed alignment rules pci 0000:02:01.0: BAR 9: assigned [mem 0x6000000000-0x6400ffffff 64bit pref] pci 0000:02:01.0: BAR 8: assigned [mem 0x40400000-0x405fffff] pci 0000:03:00.0: BAR 2: assigned [mem 0x6000000000-0x63ffffffff 64bit pref] pci 0000:03:00.0: BAR 0: assigned [mem 0x6400000000-0x6400ffffff 64bit pref] pci 0000:03:00.0: BAR 6: assigned [mem 0x40400000-0x405fffff pref] pci 0000:02:01.0: PCI bridge to [bus 03] pci 0000:02:01.0: bridge window [mem 0x40400000-0x405fffff] pci 0000:02:01.0: bridge window [mem 0x6000000000-0x6400ffffff 64bit pref] This patch draws inspiration from the initial investigations and work by Mika Westerberg. Closes: https://bugzilla.kernel.org/show_bug.cgi?id=216795 Link: https://lore.kernel.org/linux-pci/20190812144144.2646-1-mika.westerberg@linux.intel.com/ Fixes: 5d0a8965aea9 ("[PATCH] 2.5.14: New PCI allocation code (alpha, arm, parisc) [2/2]") Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> --- During our internal review, Andy Shevchenko noted that the check for ioport_resource & iomem_resource might not be needed. I've left them into pbus_upstream_assigned_limit() because I couldn't prove myself they're unnecessary and find_bus_resource_of_type() also does the same check. If the checks are not needed in pbus_upstream_assigned_limit() they should not be required in find_bus_resource_of_type() either. --- drivers/pci/setup-bus.c | 75 +++++++++++++++++++++++++++++++++++++++-- 1 file changed, 73 insertions(+), 2 deletions(-)