@@ -927,25 +927,31 @@ int dw_pcie_suspend_noirq(struct dw_pcie *pci)
if (dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKCTL) & PCI_EXP_LNKCTL_ASPM_L1)
return 0;
- /* Only send out PME_TURN_OFF when PCIE link is up */
- if (dw_pcie_get_ltssm(pci) > DW_PCIE_LTSSM_DETECT_ACT) {
- if (pci->pp.ops->pme_turn_off)
- pci->pp.ops->pme_turn_off(&pci->pp);
- else
- ret = dw_pcie_pme_turn_off(pci);
-
- if (ret)
- return ret;
+ if (pci->pp.ops->pme_turn_off)
+ pci->pp.ops->pme_turn_off(&pci->pp);
+ else
+ ret = dw_pcie_pme_turn_off(pci);
+ if (ret)
+ return ret;
- ret = read_poll_timeout(dw_pcie_get_ltssm, val, val == DW_PCIE_LTSSM_L2_IDLE,
- PCIE_PME_TO_L2_TIMEOUT_US/10,
- PCIE_PME_TO_L2_TIMEOUT_US, false, pci);
- if (ret) {
- dev_err(pci->dev, "Timeout waiting for L2 entry! LTSSM: 0x%x\n", val);
- return ret;
- }
+ ret = read_poll_timeout(dw_pcie_get_ltssm, val,
+ val == DW_PCIE_LTSSM_L2_IDLE ||
+ val <= DW_PCIE_LTSSM_DETECT_WAIT,
+ PCIE_PME_TO_L2_TIMEOUT_US/10,
+ PCIE_PME_TO_L2_TIMEOUT_US, false, pci);
+ if (ret) {
+ /* Only dump message when ltssm_stat isn't in DETECT and POLL */
+ dev_err(pci->dev, "Timeout waiting for L2 entry! LTSSM: 0x%x\n", val);
+ return ret;
}
+ /*
+ * Refer to r6.0, sec 5.3.3.2.1, software should wait at least
+ * 100ns after L2/L3 Ready before turning off refclock and
+ * main power. It's harmless too when no endpoint connected.
+ */
+ udelay(1);
+
dw_pcie_stop_link(pci);
if (pci->pp.ops->deinit)
pci->pp.ops->deinit(&pci->pp);
@@ -330,6 +330,7 @@ enum dw_pcie_ltssm {
/* Need to align with PCIE_PORT_DEBUG0 bits 0:5 */
DW_PCIE_LTSSM_DETECT_QUIET = 0x0,
DW_PCIE_LTSSM_DETECT_ACT = 0x1,
+ DW_PCIE_LTSSM_DETECT_WAIT = 0x6,
DW_PCIE_LTSSM_L0 = 0x11,
DW_PCIE_LTSSM_L2_IDLE = 0x15,
Before sending PME_TURN_OFF, don't test the LTSSM state. Since it's safe to send PME_TURN_OFF message regardless of whether the link is up or down. So, there would be no need to test the LTSSM state before sending PME_TURN_OFF message. Only print the message when ltssm_stat is not in DETECT and POLL. In the other words, there isn't an error message when no endpoint is connected at all. Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com> --- v5 changes: - Remove the redundant check "(val > DW_PCIE_LTSSM_DETECT_WAIT)". v4 changes: - Keep error return when L2 entry is failed and the endpoint is connected refer to Krishna' comments. Thanks. v3 changes: - Refine the commit message refer to Manivannan's comments. - Regarding Frank's comments, avoid 10ms wait when no link up. v2 changes: - Don't remove L2 poll check. - Add one 1us delay after L2 entry. - No error return when L2 entry is timeout - Don't print message when no link up. --- .../pci/controller/dwc/pcie-designware-host.c | 38 +++++++++++-------- drivers/pci/controller/dwc/pcie-designware.h | 1 + 2 files changed, 23 insertions(+), 16 deletions(-)