@@ -676,7 +676,6 @@ void t3_link_changed(struct adapter *adapter, int port_id);
void t3_link_fault(struct adapter *adapter, int port_id);
int t3_link_start(struct cphy *phy, struct cmac *mac, struct link_config *lc);
const struct adapter_info *t3_get_adapter_info(unsigned int board_id);
-int t3_seeprom_read(struct adapter *adapter, u32 addr, __le32 *data);
int t3_seeprom_write(struct adapter *adapter, u32 addr, __le32 data);
int t3_seeprom_wp(struct adapter *adapter, int enable);
int t3_get_tp_version(struct adapter *adapter, u32 *vers);
@@ -2036,20 +2036,16 @@ static int get_eeprom(struct net_device *dev, struct ethtool_eeprom *e,
{
struct port_info *pi = netdev_priv(dev);
struct adapter *adapter = pi->adapter;
- int i, err = 0;
-
- u8 *buf = kmalloc(EEPROMSIZE, GFP_KERNEL);
- if (!buf)
- return -ENOMEM;
+ int cnt;
e->magic = EEPROM_MAGIC;
- for (i = e->offset & ~3; !err && i < e->offset + e->len; i += 4)
- err = t3_seeprom_read(adapter, i, (__le32 *) & buf[i]);
+ cnt = pci_read_vpd(adapter->pdev, e->offset, e->len, data);
+ if (cnt < 0)
+ return cnt;
- if (!err)
- memcpy(data, buf + e->offset, e->len);
- kfree(buf);
- return err;
+ e->len = cnt;
+
+ return 0;
}
static int set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
@@ -2072,12 +2068,9 @@ static int set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom,
buf = kmalloc(aligned_len, GFP_KERNEL);
if (!buf)
return -ENOMEM;
- err = t3_seeprom_read(adapter, aligned_offset, (__le32 *) buf);
- if (!err && aligned_len > 4)
- err = t3_seeprom_read(adapter,
- aligned_offset + aligned_len - 4,
- (__le32 *) & buf[aligned_len - 4]);
- if (err)
+ err = pci_read_vpd(adapter->pdev, aligned_offset, aligned_len,
+ buf);
+ if (err < 0)
goto out;
memcpy(buf + (eeprom->offset & 3), data, eeprom->len);
} else
@@ -599,42 +599,6 @@ struct t3_vpd {
#define EEPROM_STAT_ADDR 0x4000
#define VPD_BASE 0xc00
-/**
- * t3_seeprom_read - read a VPD EEPROM location
- * @adapter: adapter to read
- * @addr: EEPROM address
- * @data: where to store the read data
- *
- * Read a 32-bit word from a location in VPD EEPROM using the card's PCI
- * VPD ROM capability. A zero is written to the flag bit when the
- * address is written to the control register. The hardware device will
- * set the flag to 1 when 4 bytes have been read into the data register.
- */
-int t3_seeprom_read(struct adapter *adapter, u32 addr, __le32 *data)
-{
- u16 val;
- int attempts = EEPROM_MAX_POLL;
- u32 v;
- unsigned int base = adapter->params.pci.vpd_cap_addr;
-
- if ((addr >= EEPROMSIZE && addr != EEPROM_STAT_ADDR) || (addr & 3))
- return -EINVAL;
-
- pci_write_config_word(adapter->pdev, base + PCI_VPD_ADDR, addr);
- do {
- udelay(10);
- pci_read_config_word(adapter->pdev, base + PCI_VPD_ADDR, &val);
- } while (!(val & PCI_VPD_ADDR_F) && --attempts);
-
- if (!(val & PCI_VPD_ADDR_F)) {
- CH_ERR(adapter, "reading EEPROM address 0x%x failed\n", addr);
- return -EIO;
- }
- pci_read_config_dword(adapter->pdev, base + PCI_VPD_DATA, &v);
- *data = cpu_to_le32(v);
- return 0;
-}
-
/**
* t3_seeprom_write - write a VPD EEPROM location
* @adapter: adapter to write
@@ -708,24 +672,22 @@ static int vpdstrtou16(char *s, u8 len, unsigned int base, u16 *val)
*/
static int get_vpd_params(struct adapter *adapter, struct vpd_params *p)
{
- int i, addr, ret;
struct t3_vpd vpd;
+ u8 base_val = 0;
+ int addr, ret;
/*
* Card information is normally at VPD_BASE but some early cards had
* it at 0.
*/
- ret = t3_seeprom_read(adapter, VPD_BASE, (__le32 *)&vpd);
- if (ret)
+ ret = pci_read_vpd(adapter->pdev, VPD_BASE, 1, &base_val);
+ if (ret < 0)
return ret;
- addr = vpd.id_tag == 0x82 ? VPD_BASE : 0;
+ addr = base_val == PCI_VPD_LRDT_ID_STRING ? VPD_BASE : 0;
- for (i = 0; i < sizeof(vpd); i += 4) {
- ret = t3_seeprom_read(adapter, addr + i,
- (__le32 *)((u8 *)&vpd + i));
- if (ret)
- return ret;
- }
+ ret = pci_read_vpd(adapter->pdev, addr, sizeof(vpd), &vpd);
+ if (ret < 0)
+ return ret;
ret = vpdstrtouint(vpd.cclk_data, vpd.cclk_len, 10, &p->cclk);
if (ret)
Using the VPD API allows to simplify the code and completely get rid of t3_seeprom_read(). Note that we don't have to use pci_read_vpd_any() here because a VPD quirk sets dev->vpd.len to the full EEPROM size. Tested with a T320 card. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> --- drivers/net/ethernet/chelsio/cxgb3/common.h | 1 - .../net/ethernet/chelsio/cxgb3/cxgb3_main.c | 27 ++++------ drivers/net/ethernet/chelsio/cxgb3/t3_hw.c | 54 +++---------------- 3 files changed, 18 insertions(+), 64 deletions(-)