@@ -34,8 +34,18 @@ properties:
- const: config # PCIe configuration space registers
reset-gpios:
- description: The GPIO to generate PCIe PERST# assert and deassert signal.
- maxItems: 1
+ description: The GPIOs to generate PCIe PERST# assert and deassert signal.
+ minItems: 1
+ maxItems: 4
+
+ clkreq-gpios:
+ description: CLKREQ signal GPIO pins to be enabled during PCI power on
+ minItems: 1
+ maxItems: 3
+
+ eye_param:
+ description: items to adjust the eye parameters
+ maxItems: 5
required:
- compatible
@@ -52,12 +62,13 @@ examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/hi3660-clock.h>
+ #include <dt-bindings/clock/hi3670-clock.h>
soc {
#address-cells = <2>;
#size-cells = <2>;
- pcie: pcie@f4000000 {
+ pcie1: pcie@f4000000 {
compatible = "hisilicon,kirin960-pcie";
reg = <0x0 0xf4000000 0x0 0x1000>,
<0x0 0xff3fe000 0x0 0x1000>,
@@ -87,4 +98,47 @@ examples:
"pcie_apb_sys", "pcie_aclk";
reset-gpios = <&gpio11 1 0 >;
};
+
+ pcie2: pcie@f5000000 {
+ compatible = "hisilicon,kirin970-pcie";
+ reg = <0x0 0xf4000000 0x0 0x1000000>,
+ <0x0 0xfc180000 0x0 0x1000>,
+ <0x0 0xfc000000 0x0 0x80000>,
+ <0x0 0xf5000000 0x0 0x2000>;
+ pci-supply = <&ldo33>;
+ reg-names = "dbi", "apb", "phy", "config";
+ bus-range = <0x0 0x1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x02000000 0x0 0x00000000 0x0 0xf6000000 0x0 0x02000000>;
+ num-lanes = <1>;
+ #interrupt-cells = <1>;
+ interrupts = <0 283 4>;
+ interrupt-names = "msi";
+ interrupt-map-mask = <0 0 0 7>;
+ interrupt-map = <0x0 0 0 1 &gic GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0 0 0 2 &gic GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0 0 0 3 &gic GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0 0 0 4 &gic GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg_ctrl HI3670_CLK_GATE_PCIEPHY_REF>,
+ <&crg_ctrl HI3670_CLK_GATE_PCIEAUX>,
+ <&crg_ctrl HI3670_PCLK_GATE_PCIE_PHY>,
+ <&crg_ctrl HI3670_PCLK_GATE_PCIE_SYS>,
+ <&crg_ctrl HI3670_ACLK_GATE_PCIE>;
+
+ clock-names = "pcie_phy_ref", "pcie_aux",
+ "pcie_apb_phy", "pcie_apb_sys",
+ "pcie_aclk";
+ reset-gpios = <&gpio7 0 0 >, <&gpio25 2 0 >,
+ <&gpio3 1 0 >, <&gpio27 4 0 >;
+
+ clkreq-gpios = <&gpio20 6 0 >, <&gpio27 3 0 >, <&gpio17 0 0 >;
+
+ /* vboost iboost pre post main */
+ eye_param = <0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF 0xFFFFFFFF>;
+ msi-parent = <&its_pcie>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_clkreq_pmx_func &pcie_clkreq_cfg_func>;
+ };
};
There are a few extra optional bindings that are needed for Hikey 970 PCI to work. Add them. Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> --- .../bindings/pci/hisilicon,kirin-pcie.yaml | 60 ++++++++++++++++++- 1 file changed, 57 insertions(+), 3 deletions(-)