deleted file mode 100644
@@ -1,52 +0,0 @@
-RISC-V Hart-Level Interrupt Controller (HLIC)
----------------------------------------------
-
-RISC-V cores include Control Status Registers (CSRs) which are local to each
-CPU core (HART in RISC-V terminology) and can be read or written by software.
-Some of these CSRs are used to control local interrupts connected to the core.
-Every interrupt is ultimately routed through a hart's HLIC before it
-interrupts that hart.
-
-The RISC-V supervisor ISA manual specifies three interrupt sources that are
-attached to every HLIC: software interrupts, the timer interrupt, and external
-interrupts. Software interrupts are used to send IPIs between cores. The
-timer interrupt comes from an architecturally mandated real-time timer that is
-controlled via Supervisor Binary Interface (SBI) calls and CSR reads. External
-interrupts connect all other device interrupts to the HLIC, which are routed
-via the platform-level interrupt controller (PLIC).
-
-All RISC-V systems that conform to the supervisor ISA specification are
-required to have a HLIC with these three interrupt sources present. Since the
-interrupt map is defined by the ISA it's not listed in the HLIC's device tree
-entry, though external interrupt controllers (like the PLIC, for example) will
-need to define how their interrupts map to the relevant HLICs. This means
-a PLIC interrupt property will typically list the HLICs for all present HARTs
-in the system.
-
-Required properties:
-- compatible : "riscv,cpu-intc"
-- #interrupt-cells : should be <1>. The interrupt sources are defined by the
- RISC-V supervisor ISA manual, with only the following three interrupts being
- defined for supervisor mode:
- - Source 1 is the supervisor software interrupt, which can be sent by an SBI
- call and is reserved for use by software.
- - Source 5 is the supervisor timer interrupt, which can be configured by
- SBI calls and implements a one-shot timer.
- - Source 9 is the supervisor external interrupt, which chains to all other
- device interrupts.
-- interrupt-controller : Identifies the node as an interrupt controller
-
-Furthermore, this interrupt-controller MUST be embedded inside the cpu
-definition of the hart whose CSRs control these local interrupts.
-
-An example device tree entry for a HLIC is show below.
-
- cpu1: cpu@1 {
- compatible = "riscv";
- ...
- cpu1-intc: interrupt-controller {
- #interrupt-cells = <1>;
- compatible = "sifive,fu540-c000-cpu-intc", "riscv,cpu-intc";
- interrupt-controller;
- };
- };
new file mode 100644
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/riscv,cpu-intc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RISC-V Hart-Level Interrupt Controller (HLIC)
+
+description:
+ RISC-V cores include Control Status Registers (CSRs) which are local to
+ each CPU core (HART in RISC-V terminology) and can be read or written by
+ software. Some of these CSRs are used to control local interrupts connected
+ to the core. Every interrupt is ultimately routed through a hart's HLIC
+ before it interrupts that hart.
+
+ The RISC-V supervisor ISA manual specifies three interrupt sources that are
+ attached to every HLIC namely software interrupts, the timer interrupt, and
+ external interrupts. Software interrupts are used to send IPIs between
+ cores. The timer interrupt comes from an architecturally mandated real-
+ time timer that is controlled via Supervisor Binary Interface (SBI) calls
+ and CSR reads. External interrupts connect all other device interrupts to
+ the HLIC, which are routed via the platform-level interrupt controller
+ (PLIC).
+
+ All RISC-V systems that conform to the supervisor ISA specification are
+ required to have a HLIC with these three interrupt sources present. Since
+ the interrupt map is defined by the ISA it's not listed in the HLIC's device
+ tree entry, though external interrupt controllers (like the PLIC, for
+ example) will need to define how their interrupts map to the relevant HLICs.
+ This means a PLIC interrupt property will typically list the HLICs for all
+ present HARTs in the system.
+
+maintainers:
+ - Palmer Dabbelt <palmer@dabbelt.com>
+ - Paul Walmsley <paul.walmsley@sifive.com>
+
+allOf:
+ - $ref: /schemas/riscv/cpus.yaml#/properties/interrupt-controller
+
+properties:
+ compatible:
+ $ref: /schemas/riscv/cpus.yaml#/properties/interrupt-controller/properties/compatible
+
+ interrupt-controller: true
+
+ '#interrupt-cells':
+ const: 1
+ description: |
+ The interrupt sources are defined by the RISC-V supervisor ISA manual,
+ with only the following three interrupts being defined for
+ supervisor mode:
+ - Source 1 is the supervisor software interrupt, which can be sent by
+ an SBI call and is reserved for use by software.
+ - Source 5 is the supervisor timer interrupt, which can be configured
+ by SBI calls and implements a one-shot timer.
+ - Source 9 is the supervisor external interrupt, which chains to all
+ other device interrupts.
+
+required:
+ - compatible
+ - '#interrupt-cells'
+ - interrupt-controller
+
+additionalProperties: false
+
+examples:
+ - |
+ interrupt-controller {
+ #interrupt-cells = <1>;
+ compatible = "riscv,cpu-intc";
+ interrupt-controller;
+ };
Convert the RISC-V Hart-Level Interrupt Controller (HLIC) to newer DT schema, Created DT schema based on the .txt file which had `compatible`, `#interrupt-cells` and `interrupt-controller` as required properties. Changes made with respect to original file: - Changed the example to just use interrupt-controller instead of using the whole cpu block - Changed the example compatible string. Signed-off-by: Kanak Shilledar <kanakshilledar111@protonmail.com> --- Changes in v2: - Update the maintainers list. - Add reference to `interrupt-controller` in `riscv/cpus.yaml`. - Update compatible property with the reference in `cpus.yaml`. - Include description for '#interrupt-cells' property. - Change '#interrupt-cells' property to have `const: 1` as per the text binding. - Fixed the warning thrown by `/renesas/r9a07g043f01-smarc.dtb`. --- .../interrupt-controller/riscv,cpu-intc.txt | 52 -------------- .../interrupt-controller/riscv,cpu-intc.yaml | 72 +++++++++++++++++++ 2 files changed, 72 insertions(+), 52 deletions(-) delete mode 100644 Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.txt create mode 100644 Documentation/devicetree/bindings/interrupt-controller/riscv,cpu-intc.yaml