diff mbox series

[8/9] qla2xxx: Make qla2x00_restart_isp() easier to read

Message ID 20200614223921.5851-9-bvanassche@acm.org (mailing list archive)
State Superseded
Headers show
Series qla2xxx patches for kernel v5.9 | expand

Commit Message

Bart Van Assche June 14, 2020, 10:39 p.m. UTC 
Instead of using complicated control flow to only have one return statement
at the end of qla2x00_restart_isp(), return an error status as soon as it is
known that this function will fail.

Cc: Nilesh Javali <njavali@marvell.com>
Cc: Quinn Tran <qutran@marvell.com>
Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
Cc: Daniel Wagner <dwagner@suse.de>
Cc: Martin Wilck <mwilck@suse.com>
Cc: Roman Bolshakov <r.bolshakov@yadro.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
---
 drivers/scsi/qla2xxx/qla_init.c | 39 +++++++++++++++++++--------------
 1 file changed, 22 insertions(+), 17 deletions(-)

Comments

Daniel Wagner June 23, 2020, 8:36 a.m. UTC | #1 
On Sun, Jun 14, 2020 at 03:39:20PM -0700, Bart Van Assche wrote:
> Instead of using complicated control flow to only have one return statement
> at the end of qla2x00_restart_isp(), return an error status as soon as it is
> known that this function will fail.
> 
> Cc: Nilesh Javali <njavali@marvell.com>
> Cc: Quinn Tran <qutran@marvell.com>
> Cc: Himanshu Madhani <himanshu.madhani@oracle.com>
> Cc: Daniel Wagner <dwagner@suse.de>
> Cc: Martin Wilck <mwilck@suse.com>
> Cc: Roman Bolshakov <r.bolshakov@yadro.com>
> Signed-off-by: Bart Van Assche <bvanassche@acm.org>

Reviewed-by: Daniel Wagner <dwagner@suse.de>
diff mbox series

Patch

diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c
index 9e12018e0105..f39a1a40d4c3 100644
--- a/drivers/scsi/qla2xxx/qla_init.c
+++ b/drivers/scsi/qla2xxx/qla_init.c
@@ -6998,36 +6998,41 @@  qla2x00_abort_isp(scsi_qla_host_t *vha)
 static int
 qla2x00_restart_isp(scsi_qla_host_t *vha)
 {
-	int status = 0;
+	int status;
 	struct qla_hw_data *ha = vha->hw;
 
 	/* If firmware needs to be loaded */
 	if (qla2x00_isp_firmware(vha)) {
 		vha->flags.online = 0;
 		status = ha->isp_ops->chip_diag(vha);
-		if (!status)
-			status = qla2x00_setup_chip(vha);
+		if (status)
+			return status;
+		status = qla2x00_setup_chip(vha);
+		if (status)
+			return status;
 	}
 
-	if (!status && !(status = qla2x00_init_rings(vha))) {
-		clear_bit(RESET_MARKER_NEEDED, &vha->dpc_flags);
-		ha->flags.chip_reset_done = 1;
+	status = qla2x00_init_rings(vha);
+	if (status)
+		return status;
 
-		/* Initialize the queues in use */
-		qla25xx_init_queues(ha);
+	clear_bit(RESET_MARKER_NEEDED, &vha->dpc_flags);
+	ha->flags.chip_reset_done = 1;
 
-		status = qla2x00_fw_ready(vha);
-		if (!status) {
-			/* Issue a marker after FW becomes ready. */
-			qla2x00_marker(vha, ha->base_qpair, 0, 0, MK_SYNC_ALL);
-			set_bit(LOOP_RESYNC_NEEDED, &vha->dpc_flags);
-		}
+	/* Initialize the queues in use */
+	qla25xx_init_queues(ha);
 
+	status = qla2x00_fw_ready(vha);
+	if (status) {
 		/* if no cable then assume it's good */
-		if ((vha->device_flags & DFLG_NO_CABLE))
-			status = 0;
+		return vha->device_flags & DFLG_NO_CABLE ? 0 : status;
 	}
-	return (status);
+
+	/* Issue a marker after FW becomes ready. */
+	qla2x00_marker(vha, ha->base_qpair, 0, 0, MK_SYNC_ALL);
+	set_bit(LOOP_RESYNC_NEEDED, &vha->dpc_flags);
+
+	return 0;
 }
 
 static int