| Message ID | 20230528001010.47868-4-guptarud@gmail.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | [v2,1/4] dt-bindings: arm: qcom: Add Samsung Galaxy Express | expand |
On 28/05/2023 02:10, Rudraksha Gupta wrote: > Add the required nodes to support USB on the MSM8960 SoC. As it's very > similar to the APQ8064 SoC, the nodes are almost identical > > Add a label to sleep_clk for the USB node to reference > > Signed-off-by: Rudraksha Gupta <guptarud@gmail.com> > + usb1: usb@12500000 { > + compatible = "qcom,ci-hdrc"; > + reg = <0x12500000 0x200>, > + <0x12500200 0x200>; > + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>; > + clock-names = "core", "iface"; > + assigned-clocks = <&gcc USB_HS1_XCVR_CLK>; > + assigned-clock-rates = <60000000>; > + resets = <&gcc USB_HS1_RESET>; > + reset-names = "core"; > + phy_type = "ulpi"; > + ahb-burst-config = <0>; > + phys = <&usb_hs1_phy>; > + phy-names = "usb-phy"; > + status = "disabled"; status is the last > + #reset-cells = <1>; > + > + ulpi { > + usb_hs1_phy: phy { > + compatible = "qcom,usb-hs-phy-msm8960", > + "qcom,usb-hs-phy"; > + clocks = <&sleep_clk>, <&cxo_board>; > + clock-names = "sleep", "ref"; > + resets = <&usb1 0>; > + reset-names = "por"; > + #phy-cells = <0>; > + }; > + }; > + }; > + Don't add stray blank lines. Best regards, Krzysztof
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi index 2a668cd535cc..b11e606440cd 100644 --- a/arch/arm/boot/dts/qcom-msm8960.dtsi +++ b/arch/arm/boot/dts/qcom-msm8960.dtsi @@ -3,6 +3,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/qcom,gcc-msm8960.h> +#include <dt-bindings/reset/qcom,gcc-msm8960.h> #include <dt-bindings/clock/qcom,lcc-msm8960.h> #include <dt-bindings/mfd/qcom-rpm.h> #include <dt-bindings/soc/qcom,gsbi.h> @@ -71,7 +72,7 @@ pxo_board: pxo_board { clock-output-names = "pxo_board"; }; - sleep_clk { + sleep_clk: sleep_clk { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <32768>; @@ -370,5 +371,37 @@ gsbi1_spi: spi@16080000 { status = "disabled"; }; }; + + usb1: usb@12500000 { + compatible = "qcom,ci-hdrc"; + reg = <0x12500000 0x200>, + <0x12500200 0x200>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>; + clock-names = "core", "iface"; + assigned-clocks = <&gcc USB_HS1_XCVR_CLK>; + assigned-clock-rates = <60000000>; + resets = <&gcc USB_HS1_RESET>; + reset-names = "core"; + phy_type = "ulpi"; + ahb-burst-config = <0>; + phys = <&usb_hs1_phy>; + phy-names = "usb-phy"; + status = "disabled"; + #reset-cells = <1>; + + ulpi { + usb_hs1_phy: phy { + compatible = "qcom,usb-hs-phy-msm8960", + "qcom,usb-hs-phy"; + clocks = <&sleep_clk>, <&cxo_board>; + clock-names = "sleep", "ref"; + resets = <&usb1 0>; + reset-names = "por"; + #phy-cells = <0>; + }; + }; + }; + }; };
Add the required nodes to support USB on the MSM8960 SoC. As it's very similar to the APQ8064 SoC, the nodes are almost identical Add a label to sleep_clk for the USB node to reference Signed-off-by: Rudraksha Gupta <guptarud@gmail.com> --- arch/arm/boot/dts/qcom-msm8960.dtsi | 35 ++++++++++++++++++++++++++++- 1 file changed, 34 insertions(+), 1 deletion(-)