@@ -269,6 +269,68 @@ struct exynos_eint_gpio_save {
u32 eint_mask;
};
+static void exynos_eint_flt_config(struct samsung_pinctrl_drv_data *d,
+ struct samsung_pin_bank *bank, int filter)
+{
+ unsigned int flt_reg, flt_con = 0;
+ unsigned int val, shift;
+ int i;
+ int loop_cnt;
+
+ /*
+ * This function sets the desired filter (digital or delay) to
+ * every pin in the bank. Note the filter selection bitfield is
+ * only found on alive banks. The FLTCON register has the
+ * following layout
+ *
+ * BitfieldName[PinNum][Bit:Bit]
+ *
+ * FLT_EN[3][31] FLT_SEL[3][30] FLT_WIDTH[3][29:24]
+ * FLT_EN[2][23] FLT_SEL[2][22] FLT_WIDTH[2][21:16]
+ * FLT_EN[1][15] FLT_SEL[1][14] FLT_WIDTH[1][13:8]
+ * FLT_EN[0][7] FLT_SEL[0][6] FLT_WIDTH[0][5:0]
+ */
+
+ flt_con |= EXYNOS9_FLTCON_EN;
+
+ if (filter)
+ flt_con |= EXYNOS9_FLTCON_SEL_DIGITAL;
+
+ flt_reg = EXYNOS_GPIO_EFLTCON_OFFSET + bank->fltcon_offset;
+
+ if (bank->nr_pins > EXYNOS9_FLTCON_NR_PIN)
+ /*
+ * if nr_pins > 4, we should set FLTCON0 register fully.
+ * (pin0 ~ 3). So loop 4 times in case of FLTCON0.
+ */
+ loop_cnt = EXYNOS9_FLTCON_NR_PIN;
+ else
+ loop_cnt = bank->nr_pins;
+
+ val = readl(d->virt_base + flt_reg);
+
+ for (i = 0; i < loop_cnt; i++) {
+ shift = i * EXYNOS9_FLTCON_LEN;
+ val &= ~(EXYNOS9_FLTCON_MASK << shift);
+ val |= (flt_con << shift);
+ }
+
+ writel(val, d->virt_base + flt_reg);
+
+ /* loop for FLTCON1 pin 4 ~ 7 */
+ if (bank->nr_pins > EXYNOS9_FLTCON_NR_PIN) {
+ val = readl(d->virt_base + flt_reg + 0x4);
+ loop_cnt = (bank->nr_pins - EXYNOS9_FLTCON_NR_PIN);
+
+ for (i = 0; i < loop_cnt; i++) {
+ shift = i * EXYNOS9_FLTCON_LEN;
+ val &= ~(EXYNOS9_FLTCON_MASK << shift);
+ val |= (flt_con << shift);
+ }
+ writel(val, d->virt_base + flt_reg + 0x4);
+ }
+}
+
/*
* exynos_eint_gpio_init() - setup handling of external gpio interrupts.
* @d: driver data of samsung pinctrl driver.
@@ -321,6 +383,9 @@ __init int exynos_eint_gpio_init(struct samsung_pinctrl_drv_data *d)
goto err_domains;
}
+ /* Set Delay Analog Filter */
+ if (bank->fltcon_type != FLT_DEFAULT)
+ exynos_eint_flt_config(d, bank, EXYNOS9_FLTCON_SEL_DELAY);
}
return 0;
@@ -555,6 +620,10 @@ __init int exynos_eint_wkup_init(struct samsung_pinctrl_drv_data *d)
if (bank->eint_type != EINT_TYPE_WKUP)
continue;
+ /* Set Digital Filter */
+ if (bank->fltcon_type != FLT_DEFAULT)
+ exynos_eint_flt_config(d, bank, EXYNOS9_FLTCON_SEL_DIGITAL);
+
bank->irq_chip = devm_kmemdup(dev, irq_chip, sizeof(*irq_chip),
GFP_KERNEL);
if (!bank->irq_chip) {
@@ -658,6 +727,7 @@ static void exynos_pinctrl_suspend_bank(
void exynos_pinctrl_suspend(struct samsung_pinctrl_drv_data *drvdata)
{
struct samsung_pin_bank *bank = drvdata->pin_banks;
+ struct samsung_pinctrl_drv_data *d = bank->drvdata;
struct exynos_irq_chip *irq_chip = NULL;
int i;
@@ -665,6 +735,9 @@ void exynos_pinctrl_suspend(struct samsung_pinctrl_drv_data *drvdata)
if (bank->eint_type == EINT_TYPE_GPIO)
exynos_pinctrl_suspend_bank(drvdata, bank);
else if (bank->eint_type == EINT_TYPE_WKUP) {
+ /* Setting Delay (Analog) Filter */
+ if (bank->fltcon_type != FLT_DEFAULT)
+ exynos_eint_flt_config(d, bank, EXYNOS9_FLTCON_SEL_DELAY);
if (!irq_chip) {
irq_chip = bank->irq_chip;
irq_chip->set_eint_wakeup_mask(drvdata,
@@ -707,11 +780,18 @@ static void exynos_pinctrl_resume_bank(
void exynos_pinctrl_resume(struct samsung_pinctrl_drv_data *drvdata)
{
struct samsung_pin_bank *bank = drvdata->pin_banks;
+ struct samsung_pinctrl_drv_data *d = bank->drvdata;
int i;
for (i = 0; i < drvdata->nr_banks; ++i, ++bank)
- if (bank->eint_type == EINT_TYPE_GPIO)
+ if (bank->eint_type == EINT_TYPE_GPIO) {
exynos_pinctrl_resume_bank(drvdata, bank);
+ } else if (bank->eint_type == EINT_TYPE_WKUP ||
+ bank->eint_type == EINT_TYPE_WKUP_MUX) {
+ /* Set Digital Filter */
+ if (bank->fltcon_type != FLT_DEFAULT)
+ exynos_eint_flt_config(d, bank, EXYNOS9_FLTCON_SEL_DIGITAL);
+ }
}
static void exynos_retention_enable(struct samsung_pinctrl_drv_data *drvdata)
@@ -50,6 +50,13 @@
#define EXYNOS_EINT_MAX_PER_BANK 8
#define EXYNOS_EINT_NR_WKUP_EINT
+/* EINT filter configuration */
+#define EXYNOS9_FLTCON_EN BIT(7)
+#define EXYNOS9_FLTCON_SEL_DIGITAL BIT(6)
+#define EXYNOS9_FLTCON_SEL_DELAY 0
+#define EXYNOS9_FLTCON_MASK 0xff
+#define EXYNOS9_FLTCON_LEN 8
+#define EXYNOS9_FLTCON_NR_PIN 4
#define EXYNOS_PIN_BANK_EINTN(pins, reg, id) \
{ \
@@ -1104,6 +1104,8 @@ samsung_pinctrl_get_soc_data(struct samsung_pinctrl_drv_data *d,
bank->eint_func = bdata->eint_func;
bank->eint_type = bdata->eint_type;
bank->eint_mask = bdata->eint_mask;
+ bank->fltcon_type = bdata->fltcon_type;
+ bank->fltcon_offset = bdata->fltcon_offset;
bank->eint_offset = bdata->eint_offset;
bank->name = bdata->name;
@@ -82,6 +82,21 @@ enum eint_type {
EINT_TYPE_WKUP_MUX,
};
+/**
+ * enum fltcon_type - filter selection
+ * @FLT_DEFAULT: filter not selectable, default digital filter
+ * @FLT_SELECT: filter selectable (digital or delay)
+ *
+ * Some banks on some SoCs (gs101 and possibly others) have a selectable
+ * filter on alive banks of 'delay/analog' or 'digital'. If the filter
+ * selection is not available then the default filter is used (digital).
+ */
+
+enum fltcon_type {
+ FLT_DEFAULT,
+ FLT_SELECTABLE,
+};
+
/* maximum length of a pin in pin descriptor (example: "gpa0-0") */
#define PIN_NAME_LENGTH 10
@@ -122,6 +137,8 @@ struct samsung_pin_bank_type {
* @eint_type: type of the external interrupt supported by the bank.
* @eint_mask: bit mask of pins which support EINT function.
* @eint_offset: SoC-specific EINT register or interrupt offset of bank.
+ * @fltcon_type: whether the filter (delay/digital) is selectable
+ * @fltcon_offset: SoC-specific EINT filter control register offset of bank.
* @name: name to be prefixed for each pin in this pin bank.
*/
struct samsung_pin_bank_data {
@@ -133,6 +150,8 @@ struct samsung_pin_bank_data {
enum eint_type eint_type;
u32 eint_mask;
u32 eint_offset;
+ enum fltcon_type fltcon_type;
+ u32 fltcon_offset;
const char *name;
};
@@ -147,6 +166,8 @@ struct samsung_pin_bank_data {
* @eint_type: type of the external interrupt supported by the bank.
* @eint_mask: bit mask of pins which support EINT function.
* @eint_offset: SoC-specific EINT register or interrupt offset of bank.
+ * @fltcon_type: whether the filter (delay/digital) is selectable
+ * @fltcon_offset: SoC-specific EINT filter control register offset of bank.
* @name: name to be prefixed for each pin in this pin bank.
* @pin_base: starting pin number of the bank.
* @soc_priv: per-bank private data for SoC-specific code.
@@ -169,6 +190,8 @@ struct samsung_pin_bank {
enum eint_type eint_type;
u32 eint_mask;
u32 eint_offset;
+ enum fltcon_type fltcon_type;
+ u32 fltcon_offset;
const char *name;
u32 pin_base;
Newer Exynos SoCs have a filter selection register on alive bank pins. This allows the selection of a digital or delay filter for each pin. If the filter selection register is not available then the default filter (digital) is applied. On suspend we apply the analog filter to all pins in the bank, and on resume the digital filter is reapplied to all pins in the bank. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> --- drivers/pinctrl/samsung/pinctrl-exynos.c | 82 ++++++++++++++++++++++- drivers/pinctrl/samsung/pinctrl-exynos.h | 7 ++ drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + drivers/pinctrl/samsung/pinctrl-samsung.h | 23 +++++++ 4 files changed, 113 insertions(+), 1 deletion(-)