@@ -69,15 +69,21 @@ static void ath9k_hw_update_nfcal_hist_buffer(struct ath_hw *ah,
int16_t *nfarray)
{
struct ath_common *common = ath9k_hw_common(ah);
+ struct ieee80211_conf *conf = &common->hw->conf;
struct ath_nf_limits *limit;
struct ath9k_nfcal_hist *h;
bool high_nf_mid = false;
+ u8 chainmask = (ah->rxchainmask << 3) | ah->rxchainmask;
int i;
h = cal->nfCalHist;
limit = ath9k_hw_get_nf_limits(ah, ah->curchan);
for (i = 0; i < NUM_NF_READINGS; i++) {
+ if (!(chainmask & (1 << i)) ||
+ ((i >= AR5416_MAX_CHAINS) && !conf_is_ht40(conf)))
+ continue;
+
h[i].nfCalBuffer[h[i].currIndex] = nfarray[i];
if (++h[i].currIndex >= ATH9K_NF_CAL_HIST_MAX)
@@ -225,6 +231,7 @@ void ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
int32_t val;
u8 chainmask = (ah->rxchainmask << 3) | ah->rxchainmask;
struct ath_common *common = ath9k_hw_common(ah);
+ struct ieee80211_conf *conf = &common->hw->conf;
s16 default_nf = ath9k_hw_get_default_nf(ah, chan);
if (ah->caldata)
@@ -234,6 +241,9 @@ void ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
if (chainmask & (1 << i)) {
s16 nfval;
+ if ((i >= AR5416_MAX_CHAINS) && !conf_is_ht40(conf))
+ continue;
+
if (h)
nfval = h[i].privNF;
else
@@ -293,6 +303,9 @@ void ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan)
ENABLE_REGWRITE_BUFFER(ah);
for (i = 0; i < NUM_NF_READINGS; i++) {
if (chainmask & (1 << i)) {
+ if ((i >= AR5416_MAX_CHAINS) && !conf_is_ht40(conf))
+ continue;
+
val = REG_READ(ah, ah->nf_regs[i]);
val &= 0xFFFFFE00;
val |= (((u32) (-50) << 1) & 0x1ff);
At present the noise floor calibration is processed in supported control and extension chains rather than required chains. Unnccesarily doing nfcal in all supported chains leads to invalid nf readings on extn chains and these invalid values got updated into history buffer. While loading those values from history buffer is moving the chip to deaf state. This issue was observed in AR9002/AR9003 chips while doing associate/dissociate in HT40 mode and interface up/down in iterative manner. After some iterations, the chip was moved to deaf state. Somehow the pci devices are recovered by poll work after chip reset. Raading the nf values in all supported extension chains when the hw is not yet configured in HT40 mode results invalid values. Cc: stable@kernel.org Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> --- drivers/net/wireless/ath/ath9k/calib.c | 13 +++++++++++++ 1 files changed, 13 insertions(+), 0 deletions(-)