diff mbox

[04/12] ath9k: turn off RXIQ calibration while re-calibrating radio

Message ID 1350288089-18808-2-git-send-email-rmanohar@qca.qualcomm.com (mailing list archive)
State Not Applicable, archived
Headers show

Commit Message

Manoharan, Rajkumar Oct. 15, 2012, 8:01 a.m. UTC 
From: Bala Shanmugam <bkamatch@qca.qualcomm.com>

TXIQ and RXIQ share the same data path to upload the measurement
result, we should turn off RXIQ calibration while re-calibrating radio

Signed-off-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
---
 drivers/net/wireless/ath/ath9k/ar9003_mci.c | 6 ++++++
 drivers/net/wireless/ath/ath9k/ar9003_phy.h | 1 +
 2 files changed, 7 insertions(+)
diff mbox

Patch

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_mci.c b/drivers/net/wireless/ath/ath9k/ar9003_mci.c
index b2b9941..c46d8f1 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_mci.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_mci.c
@@ -750,6 +750,9 @@  int ar9003_mci_end_reset(struct ath_hw *ah, struct ath9k_channel *chan,
 
 	mci_hw->bt_state = MCI_BT_AWAKE;
 
+	REG_CLR_BIT(ah, AR_PHY_TIMING4,
+		    1 << AR_PHY_TIMING_CONTROL4_DO_GAIN_DC_IQ_CAL_SHIFT);
+
 	if (caldata) {
 		caldata->done_txiqcal_once = false;
 		caldata->done_txclcal_once = false;
@@ -759,6 +762,9 @@  int ar9003_mci_end_reset(struct ath_hw *ah, struct ath9k_channel *chan,
 	if (!ath9k_hw_init_cal(ah, chan))
 		return -EIO;
 
+	REG_SET_BIT(ah, AR_PHY_TIMING4,
+		    1 << AR_PHY_TIMING_CONTROL4_DO_GAIN_DC_IQ_CAL_SHIFT);
+
 exit:
 	ar9003_mci_enable_interrupt(ah);
 	return 0;
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_phy.h b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
index 9a48e3d..8f58523 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_phy.h
+++ b/drivers/net/wireless/ath/ath9k/ar9003_phy.h
@@ -32,6 +32,7 @@ 
 #define AR_PHY_SPUR_REG     (AR_CHAN_BASE + 0x1c)
 #define AR_PHY_RX_IQCAL_CORR_B0    (AR_CHAN_BASE + 0xdc)
 #define AR_PHY_TX_IQCAL_CONTROL_3  (AR_CHAN_BASE + 0xb0)
+#define AR_PHY_TIMING_CONTROL4_DO_GAIN_DC_IQ_CAL_SHIFT 16
 
 #define AR_PHY_TIMING11_SPUR_FREQ_SD    0x3FF00000
 #define AR_PHY_TIMING11_SPUR_FREQ_SD_S  20