new file mode 100644
@@ -0,0 +1,525 @@
+/*
+ * Firmware I/O code for mac80211 ST-Ericsson CW1200 drivers
+ *
+ * Copyright (c) 2010, ST-Ericsson
+ * Author: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
+ *
+ * Based on:
+ * ST-Ericsson UMAC CW1200 driver which is
+ * Copyright (c) 2010, ST-Ericsson
+ * Author: Ajitpal Singh <ajitpal.singh@stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/vmalloc.h>
+#include <linux/sched.h>
+#include <linux/firmware.h>
+
+#include "cw1200.h"
+#include "fwio.h"
+#include "hwio.h"
+#include "sbus.h"
+#include "bh.h"
+
+static int cw1200_get_hw_type(u32 config_reg_val, int *major_revision)
+{
+ int hw_type = -1;
+ u32 silicon_type = (config_reg_val >> 24) & 0x7;
+ u32 silicon_vers = (config_reg_val >> 31) & 0x1;
+
+ switch (silicon_type) {
+ case 0x00:
+ *major_revision = 1;
+ hw_type = HIF_9000_SILICON_VERSATILE;
+ break;
+ case 0x01:
+ case 0x02: /* CW1x00 */
+ case 0x04: /* CW1x60 */
+ *major_revision = silicon_type;
+ if (silicon_vers)
+ hw_type = HIF_8601_VERSATILE;
+ else
+ hw_type = HIF_8601_SILICON;
+ break;
+ default:
+ break;
+ }
+
+ return hw_type;
+}
+
+static int cw1200_load_firmware_cw1200(struct cw1200_common *priv)
+{
+ int ret, block, num_blocks;
+ unsigned i;
+ u32 val32;
+ u32 put = 0, get = 0;
+ u8 *buf = NULL;
+ const char *fw_path;
+ const struct firmware *firmware = NULL;
+
+ /* Macroses are local. */
+#define APB_WRITE(reg, val) \
+ do { \
+ ret = cw1200_apb_write_32(priv, CW1200_APB(reg), (val)); \
+ if (ret < 0) \
+ goto error; \
+ } while (0)
+#define APB_READ(reg, val) \
+ do { \
+ ret = cw1200_apb_read_32(priv, CW1200_APB(reg), &(val)); \
+ if (ret < 0) \
+ goto error; \
+ } while (0)
+#define REG_WRITE(reg, val) \
+ do { \
+ ret = cw1200_reg_write_32(priv, (reg), (val)); \
+ if (ret < 0) \
+ goto error; \
+ } while (0)
+#define REG_READ(reg, val) \
+ do { \
+ ret = cw1200_reg_read_32(priv, (reg), &(val)); \
+ if (ret < 0) \
+ goto error; \
+ } while (0)
+
+ switch (priv->hw_revision) {
+ case CW1200_HW_REV_CUT10:
+ fw_path = FIRMWARE_CUT10;
+ if (!priv->sdd_path)
+ priv->sdd_path = SDD_FILE_10;
+ break;
+ case CW1200_HW_REV_CUT11:
+ fw_path = FIRMWARE_CUT11;
+ if (!priv->sdd_path)
+ priv->sdd_path = SDD_FILE_11;
+ break;
+ case CW1200_HW_REV_CUT20:
+ fw_path = FIRMWARE_CUT20;
+ if (!priv->sdd_path)
+ priv->sdd_path = SDD_FILE_20;
+ break;
+ case CW1200_HW_REV_CUT22:
+ fw_path = FIRMWARE_CUT22;
+ if (!priv->sdd_path)
+ priv->sdd_path = SDD_FILE_22;
+ break;
+ case CW1X60_HW_REV:
+ fw_path = FIRMWARE_CW1X60;
+ if (!priv->sdd_path)
+ priv->sdd_path = SDD_FILE_CW1X60;
+ break;
+ default:
+ pr_err("Invalid silicon revision %d.\n", priv->hw_revision);
+ return -EINVAL;
+ }
+
+ /* Initialize common registers */
+ APB_WRITE(DOWNLOAD_IMAGE_SIZE_REG, DOWNLOAD_ARE_YOU_HERE);
+ APB_WRITE(DOWNLOAD_PUT_REG, 0);
+ APB_WRITE(DOWNLOAD_GET_REG, 0);
+ APB_WRITE(DOWNLOAD_STATUS_REG, DOWNLOAD_PENDING);
+ APB_WRITE(DOWNLOAD_FLAGS_REG, 0);
+
+ /* Write the NOP Instruction */
+ REG_WRITE(ST90TDS_SRAM_BASE_ADDR_REG_ID, 0xFFF20000);
+ REG_WRITE(ST90TDS_AHB_DPORT_REG_ID, 0xEAFFFFFE);
+
+ /* Release CPU from RESET */
+ REG_READ(ST90TDS_CONFIG_REG_ID, val32);
+ val32 &= ~ST90TDS_CONFIG_CPU_RESET_BIT;
+ REG_WRITE(ST90TDS_CONFIG_REG_ID, val32);
+
+ /* Enable Clock */
+ val32 &= ~ST90TDS_CONFIG_CPU_CLK_DIS_BIT;
+ REG_WRITE(ST90TDS_CONFIG_REG_ID, val32);
+
+#ifdef CONFIG_CW1200_ETF
+ if (etf_mode)
+ fw_path = etf_firmware;
+#endif
+
+ /* Load a firmware file */
+ ret = request_firmware(&firmware, fw_path, priv->pdev);
+ if (ret) {
+ pr_err("Can't load firmware file %s.\n", fw_path);
+ goto error;
+ }
+
+ buf = kmalloc(DOWNLOAD_BLOCK_SIZE, GFP_KERNEL | GFP_DMA);
+ if (!buf) {
+ pr_err("Can't allocate firmware load buffer.\n");
+ ret = -ENOMEM;
+ goto error;
+ }
+
+ /* Check if the bootloader is ready */
+ for (i = 0; i < 100; i += 1 + i / 2) {
+ APB_READ(DOWNLOAD_IMAGE_SIZE_REG, val32);
+ if (val32 == DOWNLOAD_I_AM_HERE)
+ break;
+ mdelay(i);
+ } /* End of for loop */
+
+ if (val32 != DOWNLOAD_I_AM_HERE) {
+ pr_err("Bootloader is not ready.\n");
+ ret = -ETIMEDOUT;
+ goto error;
+ }
+
+ /* Calculcate number of download blocks */
+ num_blocks = (firmware->size - 1) / DOWNLOAD_BLOCK_SIZE + 1;
+
+ /* Updating the length in Download Ctrl Area */
+ val32 = firmware->size; /* Explicit cast from size_t to u32 */
+ APB_WRITE(DOWNLOAD_IMAGE_SIZE_REG, val32);
+
+ /* Firmware downloading loop */
+ for (block = 0; block < num_blocks; block++) {
+ size_t tx_size;
+ size_t block_size;
+
+ /* check the download status */
+ APB_READ(DOWNLOAD_STATUS_REG, val32);
+ if (val32 != DOWNLOAD_PENDING) {
+ pr_err("Bootloader reported error %d.\n", val32);
+ ret = -EIO;
+ goto error;
+ }
+
+ /* loop until put - get <= 24K */
+ for (i = 0; i < 100; i++) {
+ APB_READ(DOWNLOAD_GET_REG, get);
+ if ((put - get) <=
+ (DOWNLOAD_FIFO_SIZE - DOWNLOAD_BLOCK_SIZE))
+ break;
+ mdelay(i);
+ }
+
+ if ((put - get) > (DOWNLOAD_FIFO_SIZE - DOWNLOAD_BLOCK_SIZE)) {
+ pr_err("Timeout waiting for FIFO.\n");
+ ret = -ETIMEDOUT;
+ goto error;
+ }
+
+ /* calculate the block size */
+ tx_size = block_size = min((size_t)(firmware->size - put),
+ (size_t)DOWNLOAD_BLOCK_SIZE);
+
+ memcpy(buf, &firmware->data[put], block_size);
+ if (block_size < DOWNLOAD_BLOCK_SIZE) {
+ memset(&buf[block_size], 0,
+ DOWNLOAD_BLOCK_SIZE - block_size);
+ tx_size = DOWNLOAD_BLOCK_SIZE;
+ }
+
+ /* send the block to sram */
+ ret = cw1200_apb_write(priv,
+ CW1200_APB(DOWNLOAD_FIFO_OFFSET +
+ (put & (DOWNLOAD_FIFO_SIZE - 1))),
+ buf, tx_size);
+ if (ret < 0) {
+ pr_err("Can't write firmware block @ %d!\n",
+ put & (DOWNLOAD_FIFO_SIZE - 1));
+ goto error;
+ }
+
+ /* update the put register */
+ put += block_size;
+ APB_WRITE(DOWNLOAD_PUT_REG, put);
+ } /* End of firmware download loop */
+
+ /* Wait for the download completion */
+ for (i = 0; i < 300; i += 1 + i / 2) {
+ APB_READ(DOWNLOAD_STATUS_REG, val32);
+ if (val32 != DOWNLOAD_PENDING)
+ break;
+ mdelay(i);
+ }
+ if (val32 != DOWNLOAD_SUCCESS) {
+ pr_err("Wait for download completion failed: 0x%.8X\n", val32);
+ ret = -ETIMEDOUT;
+ goto error;
+ } else {
+ pr_info("Firmware download completed.\n");
+ ret = 0;
+ }
+
+error:
+ kfree(buf);
+ if (firmware)
+ release_firmware(firmware);
+ return ret;
+
+#undef APB_WRITE
+#undef APB_READ
+#undef REG_WRITE
+#undef REG_READ
+}
+
+
+static int config_reg_read(struct cw1200_common *priv, u32 *val)
+{
+ switch (priv->hw_type) {
+ case HIF_9000_SILICON_VERSATILE: {
+ u16 val16;
+ int ret = cw1200_reg_read_16(priv,
+ ST90TDS_CONFIG_REG_ID,
+ &val16);
+ if (ret < 0)
+ return ret;
+ *val = val16;
+ return 0;
+ }
+ case HIF_8601_VERSATILE:
+ case HIF_8601_SILICON:
+ default:
+ cw1200_reg_read_32(priv, ST90TDS_CONFIG_REG_ID, val);
+ break;
+ }
+ return 0;
+}
+
+static int config_reg_write(struct cw1200_common *priv, u32 val)
+{
+ switch (priv->hw_type) {
+ case HIF_9000_SILICON_VERSATILE:
+ return cw1200_reg_write_16(priv,
+ ST90TDS_CONFIG_REG_ID,
+ (u16)val);
+ case HIF_8601_VERSATILE:
+ case HIF_8601_SILICON:
+ default:
+ return cw1200_reg_write_32(priv, ST90TDS_CONFIG_REG_ID, val);
+ break;
+ }
+ return 0;
+}
+
+int cw1200_load_firmware(struct cw1200_common *priv)
+{
+ int ret;
+ int i;
+ u32 val32;
+ u16 val16;
+ int major_revision = -1;
+
+ /* Read CONFIG Register */
+ ret = cw1200_reg_read_32(priv, ST90TDS_CONFIG_REG_ID, &val32);
+ if (ret < 0) {
+ pr_err("Can't read config register.\n");
+ goto out;
+ }
+
+ if (val32 == 0 || val32 == 0xffffffff) {
+ pr_err("Bad config register value (0x%08x)\n", val32);
+ ret = -EIO;
+ goto out;
+ }
+
+ priv->hw_type = cw1200_get_hw_type(val32, &major_revision);
+ if (priv->hw_type < 0) {
+ pr_err("Can't deduce hardware type.\n");
+ ret = -ENOTSUPP;
+ goto out;
+ }
+
+ /* Set DPLL Reg value, and read back to confirm writes work */
+ ret = cw1200_reg_write_32(priv, ST90TDS_TSET_GEN_R_W_REG_ID,
+ cw1200_dpll_from_clk(priv->hw_refclk));
+ if (ret < 0) {
+ pr_err("Can't write DPLL register.\n");
+ goto out;
+ }
+
+ msleep(20);
+
+ ret = cw1200_reg_read_32(priv,
+ ST90TDS_TSET_GEN_R_W_REG_ID, &val32);
+ if (ret < 0) {
+ pr_err("Can't read DPLL register.\n");
+ goto out;
+ }
+
+ if (val32 != cw1200_dpll_from_clk(priv->hw_refclk)) {
+ pr_err("Unable to initialise DPLL register. Wrote 0x%.8X, Read 0x%.8X.\n",
+ cw1200_dpll_from_clk(priv->hw_refclk), val32);
+ ret = -EIO;
+ goto out;
+ }
+
+ /* Set wakeup bit in device */
+ ret = cw1200_reg_read_16(priv, ST90TDS_CONTROL_REG_ID, &val16);
+ if (ret < 0) {
+ pr_err("set_wakeup: can't read control register.\n");
+ goto out;
+ }
+
+ ret = cw1200_reg_write_16(priv, ST90TDS_CONTROL_REG_ID,
+ val16 | ST90TDS_CONT_WUP_BIT);
+ if (ret < 0) {
+ pr_err("set_wakeup: can't write control register.\n");
+ goto out;
+ }
+
+ /* Wait for wakeup */
+ for (i = 0; i < 300; i += (1 + i / 2)) {
+ ret = cw1200_reg_read_16(priv,
+ ST90TDS_CONTROL_REG_ID, &val16);
+ if (ret < 0) {
+ pr_err("wait_for_wakeup: can't read control register.\n");
+ goto out;
+ }
+
+ if (val16 & ST90TDS_CONT_RDY_BIT)
+ break;
+
+ msleep(i);
+ }
+
+ if ((val16 & ST90TDS_CONT_RDY_BIT) == 0) {
+ pr_err("wait_for_wakeup: device is not responding.\n");
+ ret = -ETIMEDOUT;
+ goto out;
+ }
+
+ switch (major_revision) {
+ case 1:
+ /* CW1200 Hardware detection logic : Check for CUT1.1 */
+ ret = cw1200_ahb_read_32(priv, CW1200_CUT_ID_ADDR, &val32);
+ if (ret) {
+ pr_err("HW detection: can't read CUT ID.\n");
+ goto out;
+ }
+
+ switch (val32) {
+ case CW1200_CUT_11_ID_STR:
+ pr_info("CW1x00 Cut 1.1 silicon detected.\n");
+ priv->hw_revision = CW1200_HW_REV_CUT11;
+ break;
+ default:
+ pr_info("CW1x00 Cut 1.0 silicon detected.\n");
+ priv->hw_revision = CW1200_HW_REV_CUT10;
+ break;
+ }
+
+ /* According to ST-E, CUT<2.0 has busted BA TID0-3.
+ Just disable it entirely...
+ */
+ priv->ba_rx_tid_mask = 0;
+ priv->ba_tx_tid_mask = 0;
+ break;
+ case 2: {
+ u32 ar1, ar2, ar3;
+ ret = cw1200_ahb_read_32(priv, CW1200_CUT2_ID_ADDR, &ar1);
+ if (ret) {
+ pr_err("(1) HW detection: can't read CUT ID\n");
+ goto out;
+ }
+ ret = cw1200_ahb_read_32(priv, CW1200_CUT2_ID_ADDR + 4, &ar2);
+ if (ret) {
+ pr_err("(2) HW detection: can't read CUT ID.\n");
+ goto out;
+ }
+
+ ret = cw1200_ahb_read_32(priv, CW1200_CUT2_ID_ADDR + 8, &ar3);
+ if (ret) {
+ pr_err("(3) HW detection: can't read CUT ID.\n");
+ goto out;
+ }
+
+ if (ar1 == CW1200_CUT_22_ID_STR1 &&
+ ar2 == CW1200_CUT_22_ID_STR2 &&
+ ar3 == CW1200_CUT_22_ID_STR3) {
+ pr_info("CW1x00 Cut 2.2 silicon detected.\n");
+ priv->hw_revision = CW1200_HW_REV_CUT22;
+ } else {
+ pr_info("CW1x00 Cut 2.0 silicon detected.\n");
+ priv->hw_revision = CW1200_HW_REV_CUT20;
+ }
+ break;
+ }
+ case 4:
+ pr_info("CW1x60 silicon detected.\n");
+ priv->hw_revision = CW1X60_HW_REV;
+ break;
+ default:
+ pr_err("Unsupported silicon major revision %d.\n",
+ major_revision);
+ ret = -ENOTSUPP;
+ goto out;
+ }
+
+ /* Checking for access mode */
+ ret = config_reg_read(priv, &val32);
+ if (ret < 0) {
+ pr_err("Can't read config register.\n");
+ goto out;
+ }
+
+ if (!(val32 & ST90TDS_CONFIG_ACCESS_MODE_BIT)) {
+ pr_err("Device is already in QUEUE mode!\n");
+ ret = -EINVAL;
+ goto out;
+ }
+
+ switch (priv->hw_type) {
+ case HIF_8601_SILICON:
+ if (priv->hw_revision == CW1X60_HW_REV) {
+ pr_err("Can't handle CW1160/1260 firmware load yet.\n");
+ ret = -ENOTSUPP;
+ goto out;
+ }
+ ret = cw1200_load_firmware_cw1200(priv);
+ break;
+ default:
+ pr_err("Can't perform firmware load for hw type %d.\n",
+ priv->hw_type);
+ ret = -ENOTSUPP;
+ goto out;
+ }
+ if (ret < 0) {
+ pr_err("Firmware load error.\n");
+ goto out;
+ }
+
+ /* Enable interrupt signalling */
+ priv->sbus_ops->lock(priv->sbus_priv);
+ ret = __cw1200_irq_enable(priv, 1);
+ priv->sbus_ops->unlock(priv->sbus_priv);
+ if (ret < 0)
+ goto unsubscribe;
+
+ /* Configure device for MESSSAGE MODE */
+ ret = config_reg_read(priv, &val32);
+ if (ret < 0) {
+ pr_err("Can't read config register.\n");
+ goto unsubscribe;
+ }
+ ret = config_reg_write(priv, val32 & ~ST90TDS_CONFIG_ACCESS_MODE_BIT);
+ if (ret < 0) {
+ pr_err("Can't write config register.\n");
+ goto unsubscribe;
+ }
+
+ /* Unless we read the CONFIG Register we are
+ * not able to get an interrupt
+ */
+ mdelay(10);
+ config_reg_read(priv, &val32);
+
+out:
+ return ret;
+
+unsubscribe:
+ /* Disable interrupt signalling */
+ priv->sbus_ops->lock(priv->sbus_priv);
+ ret = __cw1200_irq_enable(priv, 0);
+ priv->sbus_ops->unlock(priv->sbus_priv);
+ return ret;
+}
new file mode 100644
@@ -0,0 +1,39 @@
+/*
+ * Firmware API for mac80211 ST-Ericsson CW1200 drivers
+ *
+ * Copyright (c) 2010, ST-Ericsson
+ * Author: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
+ *
+ * Based on:
+ * ST-Ericsson UMAC CW1200 driver which is
+ * Copyright (c) 2010, ST-Ericsson
+ * Author: Ajitpal Singh <ajitpal.singh@stericsson.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef FWIO_H_INCLUDED
+#define FWIO_H_INCLUDED
+
+#define BOOTLOADER_CW1X60 "boot_cw1x60.bin"
+#define FIRMWARE_CW1X60 "wsm_cw1x60.bin"
+#define FIRMWARE_CUT22 "wsm_22.bin"
+#define FIRMWARE_CUT20 "wsm_20.bin"
+#define FIRMWARE_CUT11 "wsm_11.bin"
+#define FIRMWARE_CUT10 "wsm_10.bin"
+#define SDD_FILE_CW1X60 "sdd_cw1x60.bin"
+#define SDD_FILE_22 "sdd_22.bin"
+#define SDD_FILE_20 "sdd_20.bin"
+#define SDD_FILE_11 "sdd_11.bin"
+#define SDD_FILE_10 "sdd_10.bin"
+
+int cw1200_load_firmware(struct cw1200_common *priv);
+
+/* SDD definitions */
+#define SDD_PTA_CFG_ELT_ID 0xEB
+#define SDD_REFERENCE_FREQUENCY_ELT_ID 0xc5
+u32 cw1200_dpll_from_clk(u16 clk);
+
+#endif
Signed-off-by: Solomon Peachy <pizza@shaftnet.org> --- drivers/net/wireless/cw1200/fwio.c | 525 +++++++++++++++++++++++++++++++++++++ drivers/net/wireless/cw1200/fwio.h | 39 +++ 2 files changed, 564 insertions(+) create mode 100644 drivers/net/wireless/cw1200/fwio.c create mode 100644 drivers/net/wireless/cw1200/fwio.h