new file mode 100644
@@ -0,0 +1,575 @@
+/**
+ * Copyright (c) 2014 Redpine Signals Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <linux/module.h>
+#include "rsi_usb.h"
+
+/**
+ * rsi_usb_card_write() - This function writes to the USB Card.
+ * @adapter: Pointer to the adapter structure.
+ * @buf: Pointer to the buffer from where the data has to be taken.
+ * @len: Length to be written.
+ * @endpoint: Type of endpoint.
+ *
+ * Return: status: 0 on success, -1 on failure.
+ */
+static int rsi_usb_card_write(struct rsi_hw *adapter,
+ void *buf,
+ u16 len,
+ u8 endpoint)
+{
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+ int status;
+ s32 transfer;
+
+ status = usb_bulk_msg(dev->usbdev,
+ usb_sndbulkpipe(dev->usbdev,
+ dev->bulkout_endpoint_addr[endpoint - 1]),
+ buf,
+ len,
+ &transfer,
+ HZ * 5);
+
+ if (status < 0) {
+ rsi_dbg(ERR_ZONE,
+ "Card write failed with error code :%10d\n", status);
+ dev->write_fail = 1;
+ }
+ return status;
+}
+
+/**
+ * rsi_write_multiple() - This function writes multiple bytes of information
+ * to the USB card.
+ * @adapter: Pointer to the adapter structure.
+ * @addr: Address of the register.
+ * @data: Pointer to the data that has to be written.
+ * @count: Number of multiple bytes to be written.
+ *
+ * Return: 0 on success, -1 on failure.
+ */
+static int rsi_write_multiple(struct rsi_hw *adapter,
+ u8 endpoint,
+ u8 *data,
+ u32 count)
+{
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+ u8 *seg = dev->tx_buffer;
+
+ if (dev->write_fail)
+ return 0;
+
+ if (endpoint == MGMT_EP) {
+ memset(seg, 0, RSI_USB_TX_HEAD_ROOM);
+ memcpy(seg + RSI_USB_TX_HEAD_ROOM, data, count);
+ } else {
+ seg = ((u8 *)data - RSI_USB_TX_HEAD_ROOM);
+ }
+
+ return rsi_usb_card_write(adapter,
+ seg,
+ count + RSI_USB_TX_HEAD_ROOM,
+ endpoint);
+}
+
+/**
+ * rsi_find_bulk_in_and_out_endpoints() - This function initializes the bulk
+ * endpoints to the device.
+ * @interface: Pointer to the USB interface structure.
+ * @adapter: Pointer to the adapter structure.
+ *
+ * Return: ret_val: 0 on success, -ENOMEM on failure.
+ */
+static int rsi_find_bulk_in_and_out_endpoints(struct usb_interface *interface,
+ struct rsi_hw *adapter)
+{
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+ struct usb_host_interface *iface_desc;
+ struct usb_endpoint_descriptor *endpoint;
+ __le16 buffer_size;
+ int ii, bep_found = 0;
+
+ iface_desc = &(interface->altsetting[0]);
+
+ for (ii = 0; ii < iface_desc->desc.bNumEndpoints; ++ii) {
+ endpoint = &(iface_desc->endpoint[ii].desc);
+
+ if ((!(dev->bulkin_endpoint_addr)) &&
+ (endpoint->bEndpointAddress & USB_DIR_IN) &&
+ ((endpoint->bmAttributes &
+ USB_ENDPOINT_XFERTYPE_MASK) ==
+ USB_ENDPOINT_XFER_BULK)) {
+ buffer_size = endpoint->wMaxPacketSize;
+ dev->bulkin_size = buffer_size;
+ dev->bulkin_endpoint_addr =
+ endpoint->bEndpointAddress;
+ }
+
+ if (!dev->bulkout_endpoint_addr[bep_found] &&
+ !(endpoint->bEndpointAddress & USB_DIR_IN) &&
+ ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+ USB_ENDPOINT_XFER_BULK)) {
+ dev->bulkout_endpoint_addr[bep_found] =
+ endpoint->bEndpointAddress;
+ buffer_size = endpoint->wMaxPacketSize;
+ dev->bulkout_size[bep_found] = buffer_size;
+ bep_found++;
+ }
+
+ if (bep_found >= MAX_BULK_EP)
+ break;
+ }
+
+ if (!(dev->bulkin_endpoint_addr) &&
+ (dev->bulkout_endpoint_addr[0]))
+ return -EINVAL;
+
+ return 0;
+}
+
+/* rsi_usb_reg_read() - This function reads data from given register address.
+ * @usbdev: Pointer to the usb_device structure.
+ * @reg: Address of the register to be read.
+ * @value: Value to be read.
+ * @len: length of data to be read.
+ *
+ * Return: status: 0 on success, -1 on failure.
+ */
+static int rsi_usb_reg_read(struct usb_device *usbdev,
+ u32 reg,
+ u16 *value,
+ u16 len)
+{
+ u8 temp_buf[4];
+ int status = 0;
+
+ status = usb_control_msg(usbdev,
+ usb_rcvctrlpipe(usbdev, 0),
+ USB_VENDOR_REGISTER_READ,
+ USB_TYPE_VENDOR,
+ ((reg & 0xffff0000) >> 16), (reg & 0xffff),
+ (void *)temp_buf,
+ len,
+ HZ * 5);
+
+ *value = (temp_buf[0] | (temp_buf[1] << 8));
+ if (status < 0) {
+ rsi_dbg(ERR_ZONE,
+ "%s: Reg read failed with error code :%d\n",
+ __func__, status);
+ }
+ return status;
+}
+
+/**
+ * rsi_usb_reg_write() - This function writes the given data into the given
+ * register address.
+ * @usbdev: Pointer to the usb_device structure.
+ * @reg: Address of the register.
+ * @value: Value to write.
+ * @len: Length of data to be written.
+ *
+ * Return: status: 0 on success, -1 on failure.
+ */
+static int rsi_usb_reg_write(struct usb_device *usbdev,
+ u32 reg,
+ u16 value,
+ u16 len)
+{
+ u8 usb_reg_buf[4];
+ int status = 0;
+
+ usb_reg_buf[0] = (value & 0x00ff);
+ usb_reg_buf[1] = (value & 0xff00) >> 8;
+ usb_reg_buf[2] = 0x0;
+ usb_reg_buf[3] = 0x0;
+
+ status = usb_control_msg(usbdev,
+ usb_sndctrlpipe(usbdev, 0),
+ USB_VENDOR_REGISTER_WRITE,
+ USB_TYPE_VENDOR,
+ ((reg & 0xffff0000) >> 16),
+ (reg & 0xffff),
+ (void *)usb_reg_buf,
+ len,
+ HZ * 5);
+ if (status < 0) {
+ rsi_dbg(ERR_ZONE,
+ "%s: Reg write failed with error code :%d\n",
+ __func__, status);
+ }
+ return status;
+}
+
+/**
+ * rsi_rx_done_handler() - This function is called when a packet is received
+ * from USB stack. This is callback to recieve done.
+ * @urb: Received URB.
+ *
+ * Return: None.
+ */
+static void rsi_rx_done_handler(struct urb *urb)
+{
+ struct rsi_hw *adapter = urb->context;
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+
+ if (urb->status)
+ return;
+
+ rsi_set_event(&dev->rx_thread.event);
+}
+
+/**
+ * rsi_rx_urb_submit() - This function submits the given URB to the USB stack.
+ * @adapter: Pointer to the adapter structure.
+ *
+ * Return: 0 on success, -1 on failure.
+ */
+static int rsi_rx_urb_submit(struct rsi_hw *adapter)
+{
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+ struct urb *urb = dev->rx_usb_urb[0];
+ int status;
+
+ usb_fill_bulk_urb(urb,
+ dev->usbdev,
+ usb_rcvbulkpipe(dev->usbdev,
+ dev->bulkin_endpoint_addr),
+ urb->transfer_buffer,
+ 3000,
+ rsi_rx_done_handler,
+ adapter);
+
+ status = usb_submit_urb(urb, GFP_KERNEL);
+ if (status)
+ rsi_dbg(ERR_ZONE, "%s: Failed in urb submission\n", __func__);
+
+ return status;
+}
+
+/**
+ * rsi_usb_write_register_multiple() - This function writes multiple bytes of
+ * information to multiple registers.
+ * @adapter: Pointer to the adapter structure.
+ * @addr: Address of the register.
+ * @data: Pointer to the data that has to be written.
+ * @count: Number of multiple bytes to be written on to the registers.
+ *
+ * Return: status: 0 on success, -1 on failure.
+ */
+int rsi_usb_write_register_multiple(struct rsi_hw *adapter,
+ u32 addr,
+ u8 *data,
+ u32 count)
+{
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+ u8 *buf;
+ u8 transfer;
+ int status = 0;
+
+ buf = kzalloc(4096, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ while (count) {
+ transfer = min_t(int, count, 4096);
+ memcpy(buf, data, transfer);
+ status = usb_control_msg(dev->usbdev,
+ usb_sndctrlpipe(dev->usbdev, 0),
+ USB_VENDOR_REGISTER_WRITE,
+ USB_TYPE_VENDOR,
+ ((addr & 0xffff0000) >> 16),
+ (addr & 0xffff),
+ (void *)buf,
+ transfer,
+ HZ * 5);
+ if (status < 0) {
+ rsi_dbg(ERR_ZONE,
+ "Reg write failed with error code :%d\n",
+ status);
+ } else {
+ count -= transfer;
+ data += transfer;
+ addr += transfer;
+ }
+ }
+
+ kfree(buf);
+ return 0;
+}
+
+/**
+ *rsi_usb_host_intf_write_pkt() - This function writes the packet to the
+ * USB card.
+ * @adapter: Pointer to the adapter structure.
+ * @pkt: Pointer to the data to be written on to the card.
+ * @len: Length of the data to be written on to the card.
+ *
+ * Return: 0 on success, -1 on failure.
+ */
+static int rsi_usb_host_intf_write_pkt(struct rsi_hw *adapter,
+ u8 *pkt,
+ u32 len)
+{
+ u32 queueno = ((pkt[1] >> 4) & 0xf);
+ u8 endpoint;
+
+ endpoint = ((queueno == RSI_WIFI_MGMT_Q) ? MGMT_EP : DATA_EP);
+
+ return rsi_write_multiple(adapter,
+ endpoint,
+ (u8 *)pkt,
+ len);
+}
+
+/**
+ * rsi_deinit_usb_interface() - This function deinitializes the usb interface.
+ * @adapter: Pointer to the adapter structure.
+ *
+ * Return: None.
+ */
+static void rsi_deinit_usb_interface(struct rsi_hw *adapter)
+{
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+
+ rsi_kill_thread(&dev->rx_thread);
+ kfree(adapter->priv->rx_data_pkt);
+ kfree(dev->tx_buffer);
+}
+
+/**
+ * rsi_init_usb_interface() - This function initializes the usb interface.
+ * @adapter: Pointer to the adapter structure.
+ * @pfunction: Pointer to USB interface structure.
+ *
+ * Return: 0 on success, -1 on failure.
+ */
+static int rsi_init_usb_interface(struct rsi_hw *adapter,
+ struct usb_interface *pfunction)
+{
+ struct rsi_91x_usbdev *rsi_dev;
+ struct rsi_common *common = adapter->priv;
+ int status;
+
+ rsi_dev = kzalloc(sizeof(*rsi_dev), GFP_KERNEL);
+ if (!rsi_dev)
+ return -ENOMEM;
+
+ adapter->rsi_dev = rsi_dev;
+ rsi_dev->usbdev = interface_to_usbdev(pfunction);
+
+ if (rsi_find_bulk_in_and_out_endpoints(pfunction, adapter))
+ return -EINVAL;
+
+ adapter->device = &pfunction->dev;
+ usb_set_intfdata(pfunction, adapter);
+
+ common->rx_data_pkt = kmalloc(2048, GFP_KERNEL);
+ if (!common->rx_data_pkt) {
+ rsi_dbg(ERR_ZONE, "%s: Failed to allocate memory\n",
+ __func__);
+ return -ENOMEM;
+ }
+
+ rsi_dev->tx_buffer = kmalloc(2048, GFP_ATOMIC);
+ rsi_dev->rx_usb_urb[0] = usb_alloc_urb(0, GFP_KERNEL);
+ rsi_dev->rx_usb_urb[0]->transfer_buffer = adapter->priv->rx_data_pkt;
+ rsi_dev->tx_blk_size = 252;
+
+ /* Initializing function callbacks */
+ adapter->rx_urb_submit = rsi_rx_urb_submit;
+ adapter->host_intf_write_pkt = rsi_usb_host_intf_write_pkt;
+ adapter->check_hw_queue_status = rsi_usb_check_queue_status;
+ adapter->determine_event_timeout = rsi_usb_event_timeout;
+
+ rsi_init_event(&rsi_dev->rx_thread.event);
+ status = rsi_create_kthread(common, &rsi_dev->rx_thread,
+ rsi_usb_rx_thread, "RX-Thread");
+ if (status) {
+ rsi_dbg(ERR_ZONE, "%s: Unable to init rx thrd\n", __func__);
+ goto fail;
+ }
+
+#ifdef CONFIG_RSI_DEBUGFS
+ /* In USB, one less than the MAX_DEBUGFS_ENTRIES entries is required */
+ adapter->num_debugfs_entries = (MAX_DEBUGFS_ENTRIES - 1);
+#endif
+
+ rsi_dbg(INIT_ZONE, "%s: Enabled the interface\n", __func__);
+ return 0;
+
+fail:
+ kfree(rsi_dev->tx_buffer);
+ kfree(common->rx_data_pkt);
+ return status;
+}
+
+/**
+ * rsi_probe() - This function is called by kernel when the driver provided
+ * Vendor and device IDs are matched. All the initialization
+ * work is done here.
+ * @pfunction: Pointer to the USB interface structure.
+ * @id: Pointer to the usb_device_id structure.
+ *
+ * Return: 0 on success, -1 on failure.
+ */
+static int rsi_probe(struct usb_interface *pfunction,
+ const struct usb_device_id *id)
+{
+ struct rsi_hw *adapter;
+ struct rsi_91x_usbdev *dev;
+ u16 fw_status;
+
+ rsi_dbg(INIT_ZONE, "%s: Init function called\n", __func__);
+
+ adapter = rsi_91x_init();
+ if (!adapter) {
+ rsi_dbg(ERR_ZONE, "%s: Failed to init os intf ops\n",
+ __func__);
+ return 1;
+ }
+
+ if (rsi_init_usb_interface(adapter, pfunction)) {
+ rsi_dbg(ERR_ZONE, "%s: Failed to init usb interface\n",
+ __func__);
+ goto err;
+ }
+
+ rsi_dbg(ERR_ZONE, "%s: Initialized os intf ops\n", __func__);
+
+ dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+
+ if (rsi_usb_reg_read(dev->usbdev, FW_STATUS_REG, &fw_status, 2) < 0)
+ goto err1;
+ else
+ fw_status &= 1;
+
+ if (!fw_status) {
+ if (rsi_usb_device_init(adapter->priv)) {
+ rsi_dbg(ERR_ZONE, "%s: Failed in device init\n",
+ __func__);
+ goto err1;
+ }
+
+ if (rsi_usb_reg_write(dev->usbdev,
+ USB_INTERNAL_REG_1,
+ RSI_USB_READY_MAGIC_NUM, 1) < 0)
+ goto err1;
+ rsi_dbg(INIT_ZONE, "%s: Performed device init\n", __func__);
+ }
+
+ if (rsi_rx_urb_submit(adapter))
+ goto err1;
+
+ return 0;
+err1:
+ rsi_deinit_usb_interface(adapter);
+err:
+ rsi_91x_deinit(adapter);
+ rsi_dbg(ERR_ZONE, "%s: Failed in probe...Exiting\n", __func__);
+ return 1;
+}
+
+/**
+ * rsi_disconnect() - This function performs the reverse of the probe function,
+ * it deintialize the driver structure.
+ * @pfunction: Pointer to the USB interface structure.
+ *
+ * Return: None.
+ */
+static void rsi_disconnect(struct usb_interface *pfunction)
+{
+ struct rsi_hw *adapter = usb_get_intfdata(pfunction);
+
+ if (!adapter)
+ return;
+
+ rsi_mac80211_detach(adapter);
+ rsi_deinit_usb_interface(adapter);
+ rsi_91x_deinit(adapter);
+
+ rsi_dbg(INFO_ZONE, "%s: Deinitialization completed\n", __func__);
+}
+
+#ifdef CONFIG_PM
+static int rsi_suspend(struct usb_interface *intf, pm_message_t message)
+{
+ /* Not yet implemented */
+ return -ENOSYS;
+}
+
+static int rsi_resume(struct usb_interface *intf)
+{
+ /* Not yet implemented */
+ return -ENOSYS;
+}
+#endif
+
+static const struct usb_device_id rsi_dev_table[] = {
+ { USB_DEVICE(0x0303, 0x0100) },
+ { USB_DEVICE(0x041B, 0x0301) },
+ { USB_DEVICE(0x041B, 0x0201) },
+ { USB_DEVICE(0x041B, 0x9330) },
+ { /* Blank */},
+};
+
+static struct usb_driver rsi_driver = {
+ .name = "RSI-USB WLAN",
+ .probe = rsi_probe,
+ .disconnect = rsi_disconnect,
+ .id_table = rsi_dev_table,
+#ifdef CONFIG_PM
+ .suspend = rsi_suspend,
+ .resume = rsi_resume,
+#endif
+};
+
+/**
+ * rsi_module_init() - This function registers the client driver.
+ * @void: Void.
+ *
+ * Return: 0 on success.
+ */
+static int rsi_module_init(void)
+{
+ usb_register(&rsi_driver);
+ rsi_dbg(INIT_ZONE, "%s: Registering driver\n", __func__);
+ return 0;
+}
+
+/**
+ * rsi_module_exit() - This function unregisters the client driver.
+ * @void: Void.
+ *
+ * Return: None.
+ */
+static void rsi_module_exit(void)
+{
+ usb_deregister(&rsi_driver);
+ rsi_dbg(INFO_ZONE, "%s: Unregistering driver\n", __func__);
+}
+
+module_init(rsi_module_init);
+module_exit(rsi_module_exit);
+
+MODULE_AUTHOR("Redpine Signals Inc");
+MODULE_DESCRIPTION("Common USB layer for RSI drivers");
+MODULE_SUPPORTED_DEVICE("RSI-91x");
+MODULE_DEVICE_TABLE(usb, rsi_dev_table);
+MODULE_FIRMWARE(FIRMWARE_RSI9113);
+MODULE_VERSION("0.1");
+MODULE_LICENSE("Dual BSD/GPL");
new file mode 100644
@@ -0,0 +1,177 @@
+/**
+ * Copyright (c) 2014 Redpine Signals Inc.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <linux/firmware.h>
+#include "rsi_usb.h"
+
+/**
+ * rsi_copy_to_card() - This function includes the actual funtionality of
+ * copying the TA firmware to the card.Basically this
+ * function includes opening the TA file,reading the TA
+ * file and writing their values in blocks of data.
+ * @common: Pointer to the driver private structure.
+ * @fw: Pointer to the firmware value to be written.
+ * @len: length of firmware file.
+ * @num_blocks: Number of blocks to be written to the card.
+ *
+ * Return: 0 on success and -1 on failure.
+ */
+static int rsi_copy_to_card(struct rsi_common *common,
+ const u8 *fw,
+ u32 len,
+ u32 num_blocks)
+{
+ struct rsi_hw *adapter = common->priv;
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+ u32 indx, ii;
+ u32 block_size = dev->tx_blk_size;
+ u32 lsb_address;
+ u32 base_address;
+
+ base_address = TA_LOAD_ADDRESS;
+
+ for (indx = 0, ii = 0; ii < num_blocks; ii++, indx += block_size) {
+ lsb_address = base_address;
+ if (rsi_usb_write_register_multiple(adapter,
+ lsb_address,
+ (u8 *)(fw + indx),
+ block_size)) {
+ rsi_dbg(ERR_ZONE,
+ "%s: Unable to load %s blk\n", __func__,
+ FIRMWARE_RSI9113);
+ return -EIO;
+ }
+ rsi_dbg(INIT_ZONE, "%s: loading block: %d\n", __func__, ii);
+ base_address += block_size;
+ }
+
+ if (len % block_size) {
+ lsb_address = base_address;
+ if (rsi_usb_write_register_multiple(adapter,
+ lsb_address,
+ (u8 *)(fw + indx),
+ len % block_size)) {
+ rsi_dbg(ERR_ZONE,
+ "%s: Unable to load %s blk\n", __func__,
+ FIRMWARE_RSI9113);
+ return -EIO;
+ }
+ }
+ rsi_dbg(INIT_ZONE,
+ "%s: Succesfully loaded %s instructions\n", __func__,
+ FIRMWARE_RSI9113);
+
+ rsi_dbg(INIT_ZONE, "%s: loaded firmware\n", __func__);
+ return 0;
+}
+
+/**
+ * rsi_usb_rx_thread() - This is a kernel thread to receive the packets from
+ * the USB device.
+ * @common: Pointer to the driver private structure.
+ *
+ * Return: None.
+ */
+void rsi_usb_rx_thread(struct rsi_common *common)
+{
+ struct rsi_hw *adapter = common->priv;
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+ int status;
+
+ do {
+ rsi_wait_event(&dev->rx_thread.event, EVENT_WAIT_FOREVER);
+
+ if (atomic_read(&dev->rx_thread.thread_done))
+ goto out;
+
+ mutex_lock(&common->tx_rxlock);
+ status = rsi_read_pkt(common, 0);
+ if (status) {
+ rsi_dbg(ERR_ZONE, "%s: Failed To read data", __func__);
+ mutex_unlock(&common->tx_rxlock);
+ return;
+ }
+ mutex_unlock(&common->tx_rxlock);
+ rsi_reset_event(&dev->rx_thread.event);
+ if (adapter->rx_urb_submit(adapter)) {
+ rsi_dbg(ERR_ZONE,
+ "%s: Failed in urb submission", __func__);
+ return;
+ }
+ } while (1);
+
+out:
+ rsi_dbg(INFO_ZONE, "%s: Terminated thread\n", __func__);
+ complete_and_exit(&dev->rx_thread.completion, 0);
+}
+
+
+/**
+ * rsi_load_ta_instructions() - This function includes the actual funtionality
+ * of loading the TA firmware.This function also
+ * includes opening the TA file,reading the TA
+ * file and writing their value in blocks of data.
+ * @common: Pointer to the driver private structure.
+ *
+ * Return: status: 0 on success, -1 on failure.
+ */
+static int rsi_load_ta_instructions(struct rsi_common *common)
+{
+ struct rsi_hw *adapter = common->priv;
+ struct rsi_91x_usbdev *dev = (struct rsi_91x_usbdev *)adapter->rsi_dev;
+ const struct firmware *fw_entry = NULL;
+ u32 block_size = dev->tx_blk_size;
+ const u8 *fw;
+ u32 num_blocks, len;
+ int status = 0;
+
+ status = request_firmware(&fw_entry, FIRMWARE_RSI9113, adapter->device);
+ if (status < 0) {
+ rsi_dbg(ERR_ZONE, "%s Firmware file %s not found\n",
+ __func__, FIRMWARE_RSI9113);
+ return status;
+ }
+
+ fw = kmemdup(fw_entry->data, fw_entry->size, GFP_KERNEL);
+ len = fw_entry->size;
+
+ if (len % 4)
+ len += (4 - (len % 4));
+
+ num_blocks = (len / block_size);
+
+ rsi_dbg(INIT_ZONE, "%s: Instruction size:%d\n", __func__, len);
+ rsi_dbg(INIT_ZONE, "%s: num blocks: %d\n", __func__, num_blocks);
+
+ status = rsi_copy_to_card(common, fw, len, num_blocks);
+ release_firmware(fw_entry);
+ return status;
+}
+
+/**
+ * rsi_device_init() - This Function Initializes The HAL.
+ * @common: Pointer to the driver private structure.
+ *
+ * Return: 0 on success, -1 on failure.
+ */
+int rsi_usb_device_init(struct rsi_common *common)
+{
+ if (rsi_load_ta_instructions(common))
+ return -EIO;
+
+ return 0;
+ }