@@ -111,6 +111,10 @@ enum ieee80211_band {
* restrictions.
* @IEEE80211_CHAN_INDOOR_ONLY: see %NL80211_FREQUENCY_ATTR_INDOOR_ONLY
* @IEEE80211_CHAN_GO_CONCURRENT: see %NL80211_FREQUENCY_ATTR_GO_CONCURRENT
+ * @IEEE80211_CHAN_NO_20MHZ: 20 MHz bandwidth is not permitted
+ * on this channel.
+ * @IEEE80211_CHAN_NO_10MHZ: 10 MHz bandwidth is not permitted
+ * on this channel.
*
*/
enum ieee80211_channel_flags {
@@ -125,6 +129,8 @@ enum ieee80211_channel_flags {
IEEE80211_CHAN_NO_160MHZ = 1<<8,
IEEE80211_CHAN_INDOOR_ONLY = 1<<9,
IEEE80211_CHAN_GO_CONCURRENT = 1<<10,
+ IEEE80211_CHAN_NO_20MHZ = 1<<11,
+ IEEE80211_CHAN_NO_10MHZ = 1<<12,
};
#define IEEE80211_CHAN_NO_HT40 \
@@ -2358,6 +2358,10 @@ enum nl80211_band_attr {
* connected to an AP with DFS and radar detection on the UNII band (it is
* up to user-space, i.e., wpa_supplicant to perform the required
* verifications)
+ * @NL80211_FREQUENCY_ATTR_NO_20MHZ: 20 MHz operation is not allowed
+ * on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_NO_10MHZ: 10 MHz operation is not allowed
+ * on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
* currently defined
* @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
@@ -2384,6 +2388,8 @@ enum nl80211_frequency_attr {
NL80211_FREQUENCY_ATTR_DFS_CAC_TIME,
NL80211_FREQUENCY_ATTR_INDOOR_ONLY,
NL80211_FREQUENCY_ATTR_GO_CONCURRENT,
+ NL80211_FREQUENCY_ATTR_NO_20MHZ,
+ NL80211_FREQUENCY_ATTR_NO_10MHZ,
/* keep last */
__NL80211_FREQUENCY_ATTR_AFTER_LAST,
@@ -616,12 +616,14 @@ bool cfg80211_chandef_usable(struct wiphy *wiphy,
width = 5;
break;
case NL80211_CHAN_WIDTH_10:
+ prohibited_flags |= IEEE80211_CHAN_NO_10MHZ;
width = 10;
break;
case NL80211_CHAN_WIDTH_20:
if (!ht_cap->ht_supported)
return false;
case NL80211_CHAN_WIDTH_20_NOHT:
+ prohibited_flags |= IEEE80211_CHAN_NO_20MHZ;
width = 20;
break;
case NL80211_CHAN_WIDTH_40:
@@ -567,6 +567,13 @@ static int nl80211_msg_put_channel(struct sk_buff *msg,
struct ieee80211_channel *chan,
bool large)
{
+ /* Some channels must be completely excluded from the
+ * list to protect old user-space tools from breaking
+ */
+ if (!large && chan->flags &
+ (IEEE80211_CHAN_NO_10MHZ | IEEE80211_CHAN_NO_20MHZ))
+ return 0;
+
if (nla_put_u32(msg, NL80211_FREQUENCY_ATTR_FREQ,
chan->center_freq))
goto nla_put_failure;
@@ -620,6 +627,12 @@ static int nl80211_msg_put_channel(struct sk_buff *msg,
if ((chan->flags & IEEE80211_CHAN_GO_CONCURRENT) &&
nla_put_flag(msg, NL80211_FREQUENCY_ATTR_GO_CONCURRENT))
goto nla_put_failure;
+ if ((chan->flags & IEEE80211_CHAN_NO_20MHZ) &&
+ nla_put_flag(msg, NL80211_FREQUENCY_ATTR_NO_20MHZ))
+ goto nla_put_failure;
+ if ((chan->flags & IEEE80211_CHAN_NO_10MHZ) &&
+ nla_put_flag(msg, NL80211_FREQUENCY_ATTR_NO_10MHZ))
+ goto nla_put_failure;
}
if (nla_put_u32(msg, NL80211_FREQUENCY_ATTR_MAX_TX_POWER,
Since there are frequency bands (e.g. 5.9GHz) allowing channels with only 10 or 5 MHz bandwidth, this patch adds attributes that allow keeping track about this information. When channel attributes are reported to user-space, make sure to not break old tools, i.e. if the 'split wiphy dump' is enabled, report the extra attributes (if present) describing the bandwidth restrictions. If the 'split wiphy dump' is not enabled, completely omit those channels that have flags set to either IEEE80211_CHAN_NO_10MHZ or IEEE80211_CHAN_NO_20MHZ. Add the check for new bandwidth restriction flags in cfg80211_chandef_usable() to comply with the restrictions. Signed-off-by: Rostislav Lisovy <rostislav.lisovy@fel.cvut.cz> --- include/net/cfg80211.h | 6 ++++++ include/uapi/linux/nl80211.h | 6 ++++++ net/wireless/chan.c | 2 ++ net/wireless/nl80211.c | 13 +++++++++++++ 4 files changed, 27 insertions(+)