@@ -330,6 +330,83 @@ static const struct ieee80211_rate hwsim_rates[] = {
{ .bitrate = 540 }
};
+#define OUI_QCA 0x001374
+#define QCA_NL80211_SUBCMD_TEST 1
+enum qca_nl80211_vendor_subcmds {
+ QCA_WLAN_VENDOR_ATTR_TEST = 8,
+ QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_TEST
+};
+
+static const struct nla_policy
+hwsim_vendor_test_policy[QCA_WLAN_VENDOR_ATTR_MAX + 1] = {
+ [QCA_WLAN_VENDOR_ATTR_MAX] = { .type = NLA_U32 },
+};
+
+static int mac80211_hwsim_vendor_cmd_test(struct wiphy *wiphy,
+ struct wireless_dev *wdev,
+ const void *data, int data_len)
+{
+ struct sk_buff *skb;
+ struct nlattr *tb[QCA_WLAN_VENDOR_ATTR_MAX + 1];
+ int err;
+ u32 val;
+
+ err = nla_parse(tb, QCA_WLAN_VENDOR_ATTR_MAX, data, data_len,
+ hwsim_vendor_test_policy);
+ if (err)
+ return err;
+ if (!tb[QCA_WLAN_VENDOR_ATTR_TEST])
+ return -EINVAL;
+ val = nla_get_u32(tb[QCA_WLAN_VENDOR_ATTR_TEST]);
+ wiphy_debug(wiphy, "%s: test=%u\n", __func__, val);
+
+ /* Send a vendor event as a test. Note that this would not normally be
+ * done within a command handler, but rather, based on some other
+ * trigger. For simplicity, this command is used to trigger the event
+ * here.
+ *
+ * event_idx = 0 (index in mac80211_hwsim_vendor_commands)
+ */
+ skb = cfg80211_vendor_event_alloc(wiphy, wdev, 100, 0, GFP_KERNEL);
+ if (skb) {
+ /* skb_put() or nla_put() will fill up data within
+ * NL80211_ATTR_VENDOR_DATA.
+ */
+
+ /* Add vendor data */
+ nla_put_u32(skb, QCA_WLAN_VENDOR_ATTR_TEST, val + 1);
+
+ /* Send the event - this will call nla_nest_end() */
+ cfg80211_vendor_event(skb, GFP_KERNEL);
+ }
+
+ /* Send a response to the command */
+ skb = cfg80211_vendor_cmd_alloc_reply_skb(wiphy, 10);
+ if (!skb)
+ return -ENOMEM;
+
+ /* skb_put() or nla_put() will fill up data within
+ * NL80211_ATTR_VENDOR_DATA
+ */
+ nla_put_u32(skb, QCA_WLAN_VENDOR_ATTR_TEST, val + 2);
+
+ return cfg80211_vendor_cmd_reply(skb);
+}
+
+static struct wiphy_vendor_command mac80211_hwsim_vendor_commands[] = {
+ {
+ .info = { .vendor_id = OUI_QCA,
+ .subcmd = QCA_NL80211_SUBCMD_TEST },
+ .flags = WIPHY_VENDOR_CMD_NEED_NETDEV,
+ .doit = mac80211_hwsim_vendor_cmd_test,
+ }
+};
+
+/* Advertise support vendor specific events */
+static const struct nl80211_vendor_cmd_info mac80211_hwsim_vendor_events[] = {
+ { .vendor_id = OUI_QCA, .subcmd = 1 },
+};
+
static const struct ieee80211_iface_limit hwsim_if_limits[] = {
{ .max = 1, .types = BIT(NL80211_IFTYPE_ADHOC) },
{ .max = 2048, .types = BIT(NL80211_IFTYPE_STATION) |
@@ -2416,6 +2493,12 @@ static int mac80211_hwsim_new_radio(struct genl_info *info,
hw->max_rates = 4;
hw->max_rate_tries = 11;
+ hw->wiphy->vendor_commands = mac80211_hwsim_vendor_commands;
+ hw->wiphy->n_vendor_commands =
+ ARRAY_SIZE(mac80211_hwsim_vendor_commands);
+ hw->wiphy->vendor_events = mac80211_hwsim_vendor_events;
+ hw->wiphy->n_vendor_events = ARRAY_SIZE(mac80211_hwsim_vendor_events);
+
if (param->reg_strict)
hw->wiphy->regulatory_flags |= REGULATORY_STRICT_REG;
if (param->regd) {
This allows wpa_supplicant/hostapd to send a vendor command and verify response to that command and a vendor event. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> --- v2: rebased on top of updated cfg80211_vendor_event_alloc() changes drivers/net/wireless/mac80211_hwsim.c | 83 +++++++++++++++++++++++++++++++++++ 1 file changed, 83 insertions(+)