@@ -24,6 +24,7 @@
#include <linux/ip.h>
#include <linux/firmware.h>
#include <linux/etherdevice.h>
+#include <linux/irq.h>
#include "../wlcore/wlcore.h"
#include "../wlcore/debug.h"
@@ -580,7 +581,7 @@ static struct wl18xx_priv_conf wl18xx_default_priv_conf = {
static const struct wlcore_partition_set wl18xx_ptable[PART_TABLE_LEN] = {
[PART_TOP_PRCM_ELP_SOC] = {
- .mem = { .start = 0x00A02000, .size = 0x00010000 },
+ .mem = { .start = 0x00A00000, .size = 0x00012000 },
.reg = { .start = 0x00807000, .size = 0x00005000 },
.mem2 = { .start = 0x00800000, .size = 0x0000B000 },
.mem3 = { .start = 0x00000000, .size = 0x00000000 },
@@ -864,6 +865,7 @@ static int wl18xx_pre_upload(struct wl1271 *wl)
{
u32 tmp;
int ret;
+ u16 irq_invert;
BUILD_BUG_ON(sizeof(struct wl18xx_mac_and_phy_params) >
WL18XX_PHY_INIT_MEM_SIZE);
@@ -913,6 +915,28 @@ static int wl18xx_pre_upload(struct wl1271 *wl)
/* re-enable FDSP clock */
ret = wlcore_write32(wl, WL18XX_PHY_FPGA_SPARE_1,
MEM_FDSP_CLK_120_ENABLE);
+ if (ret < 0)
+ goto out;
+
+ ret = irq_get_trigger_type(wl->irq);
+ if ((ret == IRQ_TYPE_LEVEL_LOW) || (ret == IRQ_TYPE_EDGE_FALLING)) {
+ wl1271_info("using inverted interrupt logic: %d", ret);
+ ret = wlcore_set_partition(wl,
+ &wl->ptable[PART_TOP_PRCM_ELP_SOC]);
+ if (ret < 0)
+ goto out;
+
+ ret = wl18xx_top_reg_read(wl, TOP_FN0_CCCR_REG_32, &irq_invert);
+ if (ret < 0)
+ goto out;
+
+ irq_invert |= BIT(1);
+ ret = wl18xx_top_reg_write(wl, TOP_FN0_CCCR_REG_32, irq_invert);
+ if (ret < 0)
+ goto out;
+
+ ret = wlcore_set_partition(wl, &wl->ptable[PART_PHY_INIT]);
+ }
out:
return ret;
@@ -109,6 +109,7 @@
#define WL18XX_WELP_ARM_COMMAND (WL18XX_REGISTERS_BASE + 0x7100)
#define WL18XX_ENABLE (WL18XX_REGISTERS_BASE + 0x01543C)
+#define TOP_FN0_CCCR_REG_32 (WL18XX_TOP_OCP_BASE + 0x64)
/* PRCM registers */
#define PLATFORM_DETECTION 0xA0E3E0
@@ -5991,10 +5991,6 @@ static int wl12xx_get_hw_info(struct wl1271 *wl)
{
int ret;
- ret = wl12xx_set_power_on(wl);
- if (ret < 0)
- return ret;
-
ret = wlcore_read_reg(wl, REG_CHIP_ID_B, &wl->chip.id);
if (ret < 0)
goto out;
@@ -6010,7 +6006,6 @@ static int wl12xx_get_hw_info(struct wl1271 *wl)
ret = wl->ops->get_mac(wl);
out:
- wl1271_power_off(wl);
return ret;
}
@@ -6473,10 +6468,22 @@ static void wlcore_nvs_cb(const struct firmware *fw, void *context)
else
wl->irq_flags |= IRQF_ONESHOT;
+ ret = wl12xx_set_power_on(wl);
+ if (ret < 0)
+ goto out_free_nvs;
+
+ ret = wl12xx_get_hw_info(wl);
+ if (ret < 0) {
+ wl1271_error("couldn't get hw info");
+ wl1271_power_off(wl);
+ goto out_free_nvs;
+ }
+
ret = request_threaded_irq(wl->irq, hardirq_fn, wlcore_irq,
wl->irq_flags, pdev->name, wl);
if (ret < 0) {
- wl1271_error("request_irq() failed: %d", ret);
+ wl1271_error("interrupt configuration failed");
+ wl1271_power_off(wl);
goto out_free_nvs;
}
@@ -6490,12 +6497,7 @@ static void wlcore_nvs_cb(const struct firmware *fw, void *context)
}
#endif
disable_irq(wl->irq);
-
- ret = wl12xx_get_hw_info(wl);
- if (ret < 0) {
- wl1271_error("couldn't get hw info");
- goto out_irq;
- }
+ wl1271_power_off(wl);
ret = wl->ops->identify_chip(wl);
if (ret < 0)
* Interrupt request need to happen when the wilink chip is powered on and driving the wlan_irq line. This avoids spurious interrupt issues that are a result of different external pulls configuration on different platforms * Allow working with wl18xx level-low and falling edge irqs by configuring wl18xx to invert the device interrupt Signed-off-by: Eyal Reizer <eyalr@ti.com> --- drivers/net/wireless/ti/wl18xx/main.c | 26 +++++++++++++++++++++++++- drivers/net/wireless/ti/wl18xx/reg.h | 1 + drivers/net/wireless/ti/wlcore/main.c | 26 ++++++++++++++------------ 3 files changed, 40 insertions(+), 13 deletions(-)