new file mode 100644
@@ -0,0 +1,34 @@
+* Texas Instruments wl1271 wireless lan controller
+
+The wl1271 chip can be connected via SPI or via SDIO. This
+document describes the binding for the SPI connected chip.
+
+Required properties:
+- compatible : Should be "ti,wl1271"
+- reg : Chip select address of device
+- spi-max-frequency : Maximum SPI clocking speed of device in Hz
+- ref-clock-frequency : Reference clock frequency
+- interrupts-extended : Should contain parameters for 1 interrupt line.
+ Interrupt parameters: parent, line number, type.
+- vwlan-supply : Point the node of the regulator that powers/enable the wl1271 chip
+
+Optional properties:
+- clock-xtal : boolean, clock is generated from XTAL
+
+- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
+ for optional SPI connection related properties,
+
+Examples:
+
+&spi1 {
+ wl1271@1 {
+ compatible = "ti,wl1271";
+
+ reg = <1>;
+ spi-max-frequency = <48000000>;
+ clock-xtal;
+ ref-clock-frequency = <38400000>;
+ interrupts-extended = <&gpio3 8 IRQ_TYPE_LEVEL_HIGH>;
+ vwlan-supply = <&vwlan_fixed>;
+ };
+};
@@ -13,7 +13,7 @@ config WLCORE
config WLCORE_SPI
tristate "TI wlcore SPI support"
- depends on WLCORE && SPI_MASTER
+ depends on WLCORE && SPI_MASTER && OF
select CRC7
---help---
This module adds support for the SPI interface of adapters using
@@ -30,6 +30,7 @@
#include <linux/spi/spi.h>
#include <linux/wl12xx.h>
#include <linux/platform_device.h>
+#include <linux/of_irq.h>
#include <linux/regulator/consumer.h>
#include "wlcore.h"
@@ -357,6 +358,39 @@ static struct wl1271_if_operations spi_ops = {
.set_block_size = NULL,
};
+static const struct of_device_id wlcore_spi_of_match_table[] = {
+ { .compatible = "ti,wl1271" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, wlcore_spi_of_match_table);
+
+/**
+ * wlcore_probe_of - DT node parsing.
+ * @spi: SPI slave device parameters.
+ * @res: resource parameters.
+ * @glue: wl12xx SPI bus to slave device glue parameters.
+ * @pdev_data: wlcore device parameters
+ */
+static int wlcore_probe_of(struct spi_device *spi, struct wl12xx_spi_glue *glue,
+ struct wlcore_platdev_data *pdev_data)
+{
+ struct device_node *dt_node = spi->dev.of_node;
+ int ret;
+
+ if (of_find_property(dt_node, "clock-xtal", NULL))
+ pdev_data->ref_clock_xtal = true;
+
+ ret = of_property_read_u32(dt_node, "ref-clock-frequency",
+ &pdev_data->ref_clock_freq);
+ if (IS_ERR_VALUE(ret)) {
+ dev_err(glue->dev,
+ "can't get reference clock frequency (%d)\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
static int wl1271_probe(struct spi_device *spi)
{
struct wl12xx_spi_glue *glue;
@@ -366,8 +400,6 @@ static int wl1271_probe(struct spi_device *spi)
memset(&pdev_data, 0x00, sizeof(pdev_data));
- /* TODO: add DT parsing when needed */
-
pdev_data.if_ops = &spi_ops;
glue = devm_kzalloc(&spi->dev, sizeof(*glue), GFP_KERNEL);
@@ -390,6 +422,13 @@ static int wl1271_probe(struct spi_device *spi)
return PTR_ERR(glue->reg);
}
+ ret = wlcore_probe_of(spi, glue, &pdev_data);
+ if (IS_ERR_VALUE(ret)) {
+ dev_err(glue->dev,
+ "can't get device tree parameters (%d)\n", ret);
+ return ret;
+ }
+
ret = spi_setup(spi);
if (ret < 0) {
dev_err(glue->dev, "spi_setup failed\n");
@@ -407,7 +446,7 @@ static int wl1271_probe(struct spi_device *spi)
memset(res, 0x00, sizeof(res));
res[0].start = spi->irq;
- res[0].flags = IORESOURCE_IRQ;
+ res[0].flags = IORESOURCE_IRQ | irq_get_trigger_type(spi->irq);
res[0].name = "irq";
ret = platform_device_add_resources(glue->core, res, ARRAY_SIZE(res));
@@ -445,10 +484,10 @@ static int wl1271_remove(struct spi_device *spi)
return 0;
}
-
static struct spi_driver wl1271_spi_driver = {
.driver = {
.name = "wl1271_spi",
+ .of_match_table = of_match_ptr(wlcore_spi_of_match_table),
},
.probe = wl1271_probe,