@@ -307,10 +307,11 @@ void ieee80211s_update_metric(struct ieee80211_local *local,
failed = !(txinfo->flags & IEEE80211_TX_STAT_ACK);
- /* moving average, scaled to 100 */
- sta->mesh->fail_avg =
- ((80 * sta->mesh->fail_avg + 5) / 100 + 20 * failed);
- if (sta->mesh->fail_avg > 95)
+ /* moving average, scaled to 100.
+ * feed failure as 100 and success as 0
+ */
+ ewma_mesh_fail_avg_add(&sta->mesh->fail_avg, failed * 100);
+ if (ewma_mesh_fail_avg_read(&sta->mesh->fail_avg) > 95)
mesh_plink_broken(sta);
}
@@ -325,6 +326,8 @@ static u32 airtime_link_metric_get(struct ieee80211_local *local,
int rate, err;
u32 tx_time, estimated_retx;
u64 result;
+ unsigned long fail_avg =
+ ewma_mesh_fail_avg_read(&sta->mesh->fail_avg);
/* Try to get rate based on HW/SW RC algorithm.
* Rate is returned in units of Kbps, correct this
@@ -336,7 +339,7 @@ static u32 airtime_link_metric_get(struct ieee80211_local *local,
if (rate) {
err = 0;
} else {
- if (sta->mesh->fail_avg >= 100)
+ if (fail_avg >= 100)
return MAX_METRIC;
sta_set_rate_info_tx(sta, &sta->tx_stats.last_rate, &rinfo);
@@ -344,7 +347,7 @@ static u32 airtime_link_metric_get(struct ieee80211_local *local,
if (WARN_ON(!rate))
return MAX_METRIC;
- err = (sta->mesh->fail_avg << ARITH_SHIFT) / 100;
+ err = (fail_avg << ARITH_SHIFT) / 100;
}
/* bitrate is in units of 100 Kbps, while we need rate in units of
@@ -484,6 +487,9 @@ static u32 hwmp_route_info_get(struct ieee80211_sub_if_data *sdata,
? mpath->exp_time : exp_time;
mesh_path_activate(mpath);
spin_unlock_bh(&mpath->state_lock);
+ ewma_mesh_fail_avg_init(&sta->mesh->fail_avg);
+ /* init it at a low value - 0 start is tricky */
+ ewma_mesh_fail_avg_add(&sta->mesh->fail_avg, 1);
mesh_path_tx_pending(mpath);
/* draft says preq_id should be saved to, but there does
* not seem to be any use for it, skipping by now
@@ -522,6 +528,9 @@ static u32 hwmp_route_info_get(struct ieee80211_sub_if_data *sdata,
? mpath->exp_time : exp_time;
mesh_path_activate(mpath);
spin_unlock_bh(&mpath->state_lock);
+ ewma_mesh_fail_avg_init(&sta->mesh->fail_avg);
+ /* init it at a low value - 0 start is tricky */
+ ewma_mesh_fail_avg_add(&sta->mesh->fail_avg, 1);
mesh_path_tx_pending(mpath);
} else
spin_unlock_bh(&mpath->state_lock);
@@ -829,6 +829,9 @@ void mesh_path_fix_nexthop(struct mesh_path *mpath, struct sta_info *next_hop)
mpath->flags = MESH_PATH_FIXED | MESH_PATH_SN_VALID;
mesh_path_activate(mpath);
spin_unlock_bh(&mpath->state_lock);
+ ewma_mesh_fail_avg_init(&next_hop->mesh->fail_avg);
+ /* init it at a low value - 0 start is tricky */
+ ewma_mesh_fail_avg_add(&next_hop->mesh->fail_avg, 1);
mesh_path_tx_pending(mpath);
}
@@ -322,6 +322,8 @@ struct ieee80211_fast_rx {
struct rcu_head rcu_head;
};
+DECLARE_EWMA(mesh_fail_avg, 64, 8)
+
/**
* struct mesh_sta - mesh STA information
* @plink_lock: serialize access to plink fields
@@ -367,7 +369,7 @@ struct mesh_sta {
enum nl80211_mesh_power_mode nonpeer_pm;
/* moving percentage of failed MSDUs */
- unsigned int fail_avg;
+ struct ewma_mesh_fail_avg fail_avg;
};
DECLARE_EWMA(signal, 1024, 8)
As moving average is not considering fractional part, it will stuck at the same level after certain state. For example with current values, moving average stuck at 96 and it will not move forward. Fortunately current threshold is matching against 95%. If thresold is increased more than 96, mesh path never be deactivated under worst case. Fix failure average movement by using EWMA helpers. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> --- net/mac80211/mesh_hwmp.c | 21 +++++++++++++++------ net/mac80211/mesh_pathtbl.c | 3 +++ net/mac80211/sta_info.h | 4 +++- 3 files changed, 21 insertions(+), 7 deletions(-)