new file mode 100644
@@ -0,0 +1,2469 @@
+/* SPDX-License-Identifier: ISC */
+/*
+ * Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
+ */
+#ifndef ATH11K_HAL_DESC_H
+#define ATH11K_HAL_DESC_H
+
+#define BUFFER_ADDR_INFO0_ADDR GENMASK(31, 0)
+
+#define BUFFER_ADDR_INFO1_ADDR GENMASK(7, 0)
+#define BUFFER_ADDR_INFO1_RET_BUF_MGR GENMASK(10, 8)
+#define BUFFER_ADDR_INFO1_SW_COOKIE GENMASK(31, 11)
+
+struct ath11k_buffer_addr {
+ u32 info0;
+ u32 info1;
+} __packed;
+
+/* ath11k_buffer_addr
+ *
+ * info0
+ * Address (lower 32 bits) of the msdu buffer or msdu extension
+ * descriptor or Link descriptor
+ *
+ * addr
+ * Address (upper 8 bits) of the msdu buffer or msdu extension
+ * descriptor or Link descriptor
+ *
+ * return_buffer_manager (RBM)
+ * Consumer: WBM
+ * Producer: SW/FW
+ * Indicates to which buffer manager the buffer or MSDU_EXTENSION
+ * descriptor or link descriptor that is being pointed to shall be
+ * returned after the frame has been processed. It is used by WBM
+ * for routing purposes.
+ *
+ * Values are defined in enum %HAL_RX_BUF_RBM_
+ *
+ * sw_buffer_cookie
+ * Cookie field exclusively used by SW. HW ignores the contents,
+ * accept that it passes the programmed value on to other
+ * descriptors together with the physical address.
+ *
+ * Field can be used by SW to for example associate the buffers
+ * physical address with the virtual address.
+ */
+
+enum hal_tlv_tag {
+ HAL_MACTX_CBF_START = 0 /* 0x0 */,
+ HAL_PHYRX_DATA = 1 /* 0x1 */,
+ HAL_PHYRX_CBF_DATA_RESP = 2 /* 0x2 */,
+ HAL_PHYRX_ABORT_REQUEST = 3 /* 0x3 */,
+ HAL_PHYRX_USER_ABORT_NOTIFICATION = 4 /* 0x4 */,
+ HAL_MACTX_DATA_RESP = 5 /* 0x5 */,
+ HAL_MACTX_CBF_DATA = 6 /* 0x6 */,
+ HAL_MACTX_CBF_DONE = 7 /* 0x7 */,
+ HAL_MACRX_CBF_READ_REQUEST = 8 /* 0x8 */,
+ HAL_MACRX_CBF_DATA_REQUEST = 9 /* 0x9 */,
+ HAL_MACRX_EXPECT_NDP_RECEPTION = 10 /* 0xa */,
+ HAL_MACRX_FREEZE_CAPTURE_CHANNEL = 11 /* 0xb */,
+ HAL_MACRX_NDP_TIMEOUT = 12 /* 0xc */,
+ HAL_MACRX_ABORT_ACK = 13 /* 0xd */,
+ HAL_MACRX_REQ_IMPLICIT_FB = 14 /* 0xe */,
+ HAL_MACRX_CHAIN_MASK = 15 /* 0xf */,
+ HAL_MACRX_NAP_USER = 16 /* 0x10 */,
+ HAL_MACRX_ABORT_REQUEST = 17 /* 0x11 */,
+ HAL_PHYTX_OTHER_TRANSMIT_INFO16 = 18 /* 0x12 */,
+ HAL_PHYTX_ABORT_ACK = 19 /* 0x13 */,
+ HAL_PHYTX_ABORT_REQUEST = 20 /* 0x14 */,
+ HAL_PHYTX_PKT_END = 21 /* 0x15 */,
+ HAL_PHYTX_PPDU_HEADER_INFO_REQUEST = 22 /* 0x16 */,
+ HAL_PHYTX_REQUEST_CTRL_INFO = 23 /* 0x17 */,
+ HAL_PHYTX_DATA_REQUEST = 24 /* 0x18 */,
+ HAL_PHYTX_BF_CV_LOADING_DONE = 25 /* 0x19 */,
+ HAL_PHYTX_NAP_ACK = 26 /* 0x1a */,
+ HAL_PHYTX_NAP_DONE = 27 /* 0x1b */,
+ HAL_PHYTX_OFF_ACK = 28 /* 0x1c */,
+ HAL_PHYTX_ON_ACK = 29 /* 0x1d */,
+ HAL_PHYTX_SYNTH_OFF_ACK = 30 /* 0x1e */,
+ HAL_PHYTX_DEBUG16 = 31 /* 0x1f */,
+ HAL_MACTX_ABORT_REQUEST = 32 /* 0x20 */,
+ HAL_MACTX_ABORT_ACK = 33 /* 0x21 */,
+ HAL_MACTX_PKT_END = 34 /* 0x22 */,
+ HAL_MACTX_PRE_PHY_DESC = 35 /* 0x23 */,
+ HAL_MACTX_BF_PARAMS_COMMON = 36 /* 0x24 */,
+ HAL_MACTX_BF_PARAMS_PER_USER = 37 /* 0x25 */,
+ HAL_MACTX_PREFETCH_CV = 38 /* 0x26 */,
+ HAL_MACTX_USER_DESC_COMMON = 39 /* 0x27 */,
+ HAL_MACTX_USER_DESC_PER_USER = 40 /* 0x28 */,
+ HAL_EXAMPLE_USER_TLV_16 = 41 /* 0x29 */,
+ HAL_EXAMPLE_TLV_16 = 42 /* 0x2a */,
+ HAL_MACTX_PHY_OFF = 43 /* 0x2b */,
+ HAL_MACTX_PHY_ON = 44 /* 0x2c */,
+ HAL_MACTX_SYNTH_OFF = 45 /* 0x2d */,
+ HAL_MACTX_EXPECT_CBF_COMMON = 46 /* 0x2e */,
+ HAL_MACTX_EXPECT_CBF_PER_USER = 47 /* 0x2f */,
+ HAL_MACTX_PHY_DESC = 48 /* 0x30 */,
+ HAL_MACTX_L_SIG_A = 49 /* 0x31 */,
+ HAL_MACTX_L_SIG_B = 50 /* 0x32 */,
+ HAL_MACTX_HT_SIG = 51 /* 0x33 */,
+ HAL_MACTX_VHT_SIG_A = 52 /* 0x34 */,
+ HAL_MACTX_VHT_SIG_B_SU20 = 53 /* 0x35 */,
+ HAL_MACTX_VHT_SIG_B_SU40 = 54 /* 0x36 */,
+ HAL_MACTX_VHT_SIG_B_SU80 = 55 /* 0x37 */,
+ HAL_MACTX_VHT_SIG_B_SU160 = 56 /* 0x38 */,
+ HAL_MACTX_VHT_SIG_B_MU20 = 57 /* 0x39 */,
+ HAL_MACTX_VHT_SIG_B_MU40 = 58 /* 0x3a */,
+ HAL_MACTX_VHT_SIG_B_MU80 = 59 /* 0x3b */,
+ HAL_MACTX_VHT_SIG_B_MU160 = 60 /* 0x3c */,
+ HAL_MACTX_SERVICE = 61 /* 0x3d */,
+ HAL_MACTX_HE_SIG_A_SU = 62 /* 0x3e */,
+ HAL_MACTX_HE_SIG_A_MU_DL = 63 /* 0x3f */,
+ HAL_MACTX_HE_SIG_A_MU_UL = 64 /* 0x40 */,
+ HAL_MACTX_HE_SIG_B1_MU = 65 /* 0x41 */,
+ HAL_MACTX_HE_SIG_B2_MU = 66 /* 0x42 */,
+ HAL_MACTX_HE_SIG_B2_OFDMA = 67 /* 0x43 */,
+ HAL_MACTX_DELETE_CV = 68 /* 0x44 */,
+ HAL_MACTX_MU_UPLINK_COMMON = 69 /* 0x45 */,
+ HAL_MACTX_MU_UPLINK_USER_SETUP = 70 /* 0x46 */,
+ HAL_MACTX_OTHER_TRANSMIT_INFO = 71 /* 0x47 */,
+ HAL_MACTX_PHY_NAP = 72 /* 0x48 */,
+ HAL_MACTX_DEBUG = 73 /* 0x49 */,
+ HAL_PHYRX_ABORT_ACK = 74 /* 0x4a */,
+ HAL_PHYRX_GENERATED_CBF_DETAILS = 75 /* 0x4b */,
+ HAL_PHYRX_RSSI_LEGACY = 76 /* 0x4c */,
+ HAL_PHYRX_RSSI_HT = 77 /* 0x4d */,
+ HAL_PHYRX_USER_INFO = 78 /* 0x4e */,
+ HAL_PHYRX_PKT_END = 79 /* 0x4f */,
+ HAL_PHYRX_DEBUG = 80 /* 0x50 */,
+ HAL_PHYRX_CBF_TRANSFER_DONE = 81 /* 0x51 */,
+ HAL_PHYRX_CBF_TRANSFER_ABORT = 82 /* 0x52 */,
+ HAL_PHYRX_L_SIG_A = 83 /* 0x53 */,
+ HAL_PHYRX_L_SIG_B = 84 /* 0x54 */,
+ HAL_PHYRX_HT_SIG = 85 /* 0x55 */,
+ HAL_PHYRX_VHT_SIG_A = 86 /* 0x56 */,
+ HAL_PHYRX_VHT_SIG_B_SU20 = 87 /* 0x57 */,
+ HAL_PHYRX_VHT_SIG_B_SU40 = 88 /* 0x58 */,
+ HAL_PHYRX_VHT_SIG_B_SU80 = 89 /* 0x59 */,
+ HAL_PHYRX_VHT_SIG_B_SU160 = 90 /* 0x5a */,
+ HAL_PHYRX_VHT_SIG_B_MU20 = 91 /* 0x5b */,
+ HAL_PHYRX_VHT_SIG_B_MU40 = 92 /* 0x5c */,
+ HAL_PHYRX_VHT_SIG_B_MU80 = 93 /* 0x5d */,
+ HAL_PHYRX_VHT_SIG_B_MU160 = 94 /* 0x5e */,
+ HAL_PHYRX_HE_SIG_A_SU = 95 /* 0x5f */,
+ HAL_PHYRX_HE_SIG_A_MU_DL = 96 /* 0x60 */,
+ HAL_PHYRX_HE_SIG_A_MU_UL = 97 /* 0x61 */,
+ HAL_PHYRX_HE_SIG_B1_MU = 98 /* 0x62 */,
+ HAL_PHYRX_HE_SIG_B2_MU = 99 /* 0x63 */,
+ HAL_PHYRX_HE_SIG_B2_OFDMA = 100 /* 0x64 */,
+ HAL_PHYRX_OTHER_RECEIVE_INFO = 101 /* 0x65 */,
+ HAL_PHYRX_COMMON_USER_INFO = 102 /* 0x66 */,
+ HAL_PHYRX_DATA_DONE = 103 /* 0x67 */,
+ HAL_RECEIVE_RSSI_INFO = 104 /* 0x68 */,
+ HAL_RECEIVE_USER_INFO = 105 /* 0x69 */,
+ HAL_MIMO_CONTROL_INFO = 106 /* 0x6a */,
+ HAL_RX_LOCATION_INFO = 107 /* 0x6b */,
+ HAL_COEX_TX_REQ = 108 /* 0x6c */,
+ HAL_DUMMY = 109 /* 0x6d */,
+ HAL_RX_TIMING_OFFSET_INFO = 110 /* 0x6e */,
+ HAL_EXAMPLE_TLV_32_NAME = 111 /* 0x6f */,
+ HAL_MPDU_LIMIT = 112 /* 0x70 */,
+ HAL_NA_LENGTH_END = 113 /* 0x71 */,
+ HAL_OLE_BUF_STATUS = 114 /* 0x72 */,
+ HAL_PCU_PPDU_SETUP_DONE = 115 /* 0x73 */,
+ HAL_PCU_PPDU_SETUP_END = 116 /* 0x74 */,
+ HAL_PCU_PPDU_SETUP_INIT = 117 /* 0x75 */,
+ HAL_PCU_PPDU_SETUP_START = 118 /* 0x76 */,
+ HAL_PDG_FES_SETUP = 119 /* 0x77 */,
+ HAL_PDG_RESPONSE = 120 /* 0x78 */,
+ HAL_PDG_TX_REQ = 121 /* 0x79 */,
+ HAL_SCH_WAIT_INSTR = 122 /* 0x7a */,
+ HAL_SCHEDULER_TLV = 123 /* 0x7b */,
+ HAL_TQM_FLOW_EMPTY_STATUS = 124 /* 0x7c */,
+ HAL_TQM_FLOW_NOT_EMPTY_STATUS = 125 /* 0x7d */,
+ HAL_TQM_GEN_MPDU_LENGTH_LIST = 126 /* 0x7e */,
+ HAL_TQM_GEN_MPDU_LENGTH_LIST_STATUS = 127 /* 0x7f */,
+ HAL_TQM_GEN_MPDUS = 128 /* 0x80 */,
+ HAL_TQM_GEN_MPDUS_STATUS = 129 /* 0x81 */,
+ HAL_TQM_REMOVE_MPDU = 130 /* 0x82 */,
+ HAL_TQM_REMOVE_MPDU_STATUS = 131 /* 0x83 */,
+ HAL_TQM_REMOVE_MSDU = 132 /* 0x84 */,
+ HAL_TQM_REMOVE_MSDU_STATUS = 133 /* 0x85 */,
+ HAL_TQM_UPDATE_TX_MPDU_COUNT = 134 /* 0x86 */,
+ HAL_TQM_WRITE_CMD = 135 /* 0x87 */,
+ HAL_OFDMA_TRIGGER_DETAILS = 136 /* 0x88 */,
+ HAL_TX_DATA = 137 /* 0x89 */,
+ HAL_TX_FES_SETUP = 138 /* 0x8a */,
+ HAL_RX_PACKET = 139 /* 0x8b */,
+ HAL_EXPECTED_RESPONSE = 140 /* 0x8c */,
+ HAL_TX_MPDU_END = 141 /* 0x8d */,
+ HAL_TX_MPDU_START = 142 /* 0x8e */,
+ HAL_TX_MSDU_END = 143 /* 0x8f */,
+ HAL_TX_MSDU_START = 144 /* 0x90 */,
+ HAL_TX_SW_MODE_SETUP = 145 /* 0x91 */,
+ HAL_TXPCU_BUFFER_STATUS = 146 /* 0x92 */,
+ HAL_TXPCU_USER_BUFFER_STATUS = 147 /* 0x93 */,
+ HAL_DATA_TO_TIME_CONFIG = 148 /* 0x94 */,
+ HAL_EXAMPLE_USER_TLV_32 = 149 /* 0x95 */,
+ HAL_MPDU_INFO = 150 /* 0x96 */,
+ HAL_PDG_USER_SETUP = 151 /* 0x97 */,
+ HAL_TX_11AH_SETUP = 152 /* 0x98 */,
+ HAL_REO_UPDATE_RX_REO_QUEUE_STATUS = 153 /* 0x99 */,
+ HAL_TX_PEER_ENTRY = 154 /* 0x9a */,
+ HAL_TX_RAW_OR_NATIVE_FRAME_SETUP = 155 /* 0x9b */,
+ HAL_EXAMPLE_STRUCT_NAME = 156 /* 0x9c */,
+ HAL_PCU_PPDU_SETUP_END_INFO = 157 /* 0x9d */,
+ HAL_PPDU_RATE_SETTING = 158 /* 0x9e */,
+ HAL_PROT_RATE_SETTING = 159 /* 0x9f */,
+ HAL_RX_MPDU_DETAILS = 160 /* 0xa0 */,
+ HAL_EXAMPLE_USER_TLV_42 = 161 /* 0xa1 */,
+ HAL_RX_MSDU_LINK = 162 /* 0xa2 */,
+ HAL_RX_REO_QUEUE = 163 /* 0xa3 */,
+ HAL_ADDR_SEARCH_ENTRY = 164 /* 0xa4 */,
+ HAL_SCHEDULER_CMD = 165 /* 0xa5 */,
+ HAL_TX_FLUSH = 166 /* 0xa6 */,
+ HAL_TQM_ENTRANCE_RING = 167 /* 0xa7 */,
+ HAL_TX_DATA_WORD = 168 /* 0xa8 */,
+ HAL_TX_MPDU_DETAILS = 169 /* 0xa9 */,
+ HAL_TX_MPDU_LINK = 170 /* 0xaa */,
+ HAL_TX_MPDU_LINK_PTR = 171 /* 0xab */,
+ HAL_TX_MPDU_QUEUE_HEAD = 172 /* 0xac */,
+ HAL_TX_MPDU_QUEUE_EXT = 173 /* 0xad */,
+ HAL_TX_MPDU_QUEUE_EXT_PTR = 174 /* 0xae */,
+ HAL_TX_MSDU_DETAILS = 175 /* 0xaf */,
+ HAL_TX_MSDU_EXTENSION = 176 /* 0xb0 */,
+ HAL_TX_MSDU_FLOW = 177 /* 0xb1 */,
+ HAL_TX_MSDU_LINK = 178 /* 0xb2 */,
+ HAL_TX_MSDU_LINK_ENTRY_PTR = 179 /* 0xb3 */,
+ HAL_RESPONSE_RATE_SETTING = 180 /* 0xb4 */,
+ HAL_TXPCU_BUFFER_BASICS = 181 /* 0xb5 */,
+ HAL_UNIFORM_DESCRIPTOR_HEADER = 182 /* 0xb6 */,
+ HAL_UNIFORM_TQM_CMD_HEADER = 183 /* 0xb7 */,
+ HAL_UNIFORM_TQM_STATUS_HEADER = 184 /* 0xb8 */,
+ HAL_USER_RATE_SETTING = 185 /* 0xb9 */,
+ HAL_WBM_BUFFER_RING = 186 /* 0xba */,
+ HAL_WBM_LINK_DESCRIPTOR_RING = 187 /* 0xbb */,
+ HAL_WBM_RELEASE_RING = 188 /* 0xbc */,
+ HAL_TX_FLUSH_REQ = 189 /* 0xbd */,
+ HAL_RX_MSDU_DETAILS = 190 /* 0xbe */,
+ HAL_TQM_WRITE_CMD_STATUS = 191 /* 0xbf */,
+ HAL_TQM_GET_MPDU_QUEUE_STATS = 192 /* 0xc0 */,
+ HAL_TQM_GET_MSDU_FLOW_STATS = 193 /* 0xc1 */,
+ HAL_EXAMPLE_USER_CTLV_32 = 194 /* 0xc2 */,
+ HAL_TX_FES_STATUS_START = 195 /* 0xc3 */,
+ HAL_TX_FES_STATUS_USER_PPDU = 196 /* 0xc4 */,
+ HAL_TX_FES_STATUS_USER_RESPONSE = 197 /* 0xc5 */,
+ HAL_TX_FES_STATUS_END = 198 /* 0xc6 */,
+ HAL_RX_TRIG_INFO = 199 /* 0xc7 */,
+ HAL_RXPCU_TX_SETUP_CLEAR = 200 /* 0xc8 */,
+ HAL_RX_FRAME_BITMAP_REQ = 201 /* 0xc9 */,
+ HAL_RX_FRAME_BITMAP_ACK = 202 /* 0xca */,
+ HAL_COEX_RX_STATUS = 203 /* 0xcb */,
+ HAL_RX_START_PARAM = 204 /* 0xcc */,
+ HAL_RX_PPDU_START = 205 /* 0xcd */,
+ HAL_RX_PPDU_END = 206 /* 0xce */,
+ HAL_RX_MPDU_START = 207 /* 0xcf */,
+ HAL_RX_MPDU_END = 208 /* 0xd0 */,
+ HAL_RX_MSDU_START = 209 /* 0xd1 */,
+ HAL_RX_MSDU_END = 210 /* 0xd2 */,
+ HAL_RX_ATTENTION = 211 /* 0xd3 */,
+ HAL_RECEIVED_RESPONSE_INFO = 212 /* 0xd4 */,
+ HAL_RX_PHY_SLEEP = 213 /* 0xd5 */,
+ HAL_RX_HEADER = 214 /* 0xd6 */,
+ HAL_RX_PEER_ENTRY = 215 /* 0xd7 */,
+ HAL_RX_FLUSH = 216 /* 0xd8 */,
+ HAL_RX_RESPONSE_REQUIRED_INFO = 217 /* 0xd9 */,
+ HAL_RX_FRAMELESS_BAR_DETAILS = 218 /* 0xda */,
+ HAL_TQM_GET_MPDU_QUEUE_STATS_STATUS = 219 /* 0xdb */,
+ HAL_TQM_GET_MSDU_FLOW_STATS_STATUS = 220 /* 0xdc */,
+ HAL_TX_CBF_INFO = 221 /* 0xdd */,
+ HAL_PCU_PPDU_SETUP_USER = 222 /* 0xde */,
+ HAL_RX_MPDU_PCU_START = 223 /* 0xdf */,
+ HAL_RX_PM_INFO = 224 /* 0xe0 */,
+ HAL_RX_USER_PPDU_END = 225 /* 0xe1 */,
+ HAL_RX_PRE_PPDU_START = 226 /* 0xe2 */,
+ HAL_RX_PREAMBLE = 227 /* 0xe3 */,
+ HAL_TX_FES_SETUP_COMPLETE = 228 /* 0xe4 */,
+ HAL_TX_LAST_MPDU_FETCHED = 229 /* 0xe5 */,
+ HAL_TXDMA_STOP_REQUEST = 230 /* 0xe6 */,
+ HAL_RXPCU_SETUP = 231 /* 0xe7 */,
+ HAL_RXPCU_USER_SETUP = 232 /* 0xe8 */,
+ HAL_TX_FES_STATUS_ACK_OR_BA = 233 /* 0xe9 */,
+ HAL_TQM_ACKED_MPDU = 234 /* 0xea */,
+ HAL_COEX_TX_RESP = 235 /* 0xeb */,
+ HAL_COEX_TX_STATUS = 236 /* 0xec */,
+ HAL_MACTX_COEX_PHY_CTRL = 237 /* 0xed */,
+ HAL_COEX_STATUS_BROADCAST = 238 /* 0xee */,
+ HAL_RESPONSE_START_STATUS = 239 /* 0xef */,
+ HAL_RESPONSE_END_STATUS = 240 /* 0xf0 */,
+ HAL_CRYPTO_STATUS = 241 /* 0xf1 */,
+ HAL_RECEIVED_TRIGGER_INFO = 242 /* 0xf2 */,
+ HAL_REO_ENTRANCE_RING = 243 /* 0xf3 */,
+ HAL_RX_MPDU_LINK = 244 /* 0xf4 */,
+ HAL_COEX_TX_STOP_CTRL = 245 /* 0xf5 */,
+ HAL_RX_PPDU_ACK_REPORT = 246 /* 0xf6 */,
+ HAL_RX_PPDU_NO_ACK_REPORT = 247 /* 0xf7 */,
+ HAL_SCH_COEX_STATUS = 248 /* 0xf8 */,
+ HAL_SCHEDULER_COMMAND_STATUS = 249 /* 0xf9 */,
+ HAL_SCHEDULER_RX_PPDU_NO_RESPONSE_STATUS = 250 /* 0xfa */,
+ HAL_TX_FES_STATUS_PROT = 251 /* 0xfb */,
+ HAL_TX_FES_STATUS_START_PPDU = 252 /* 0xfc */,
+ HAL_TX_FES_STATUS_START_PROT = 253 /* 0xfd */,
+ HAL_TXPCU_PHYTX_DEBUG32 = 254 /* 0xfe */,
+ HAL_TXPCU_PHYTX_OTHER_TRANSMIT_INFO32 = 255 /* 0xff */,
+ HAL_TX_MPDU_COUNT_TRANSFER_END = 256 /* 0x100 */,
+ HAL_WHO_ANCHOR_OFFSET = 257 /* 0x101 */,
+ HAL_WHO_ANCHOR_VALUE = 258 /* 0x102 */,
+ HAL_WHO_CCE_INFO = 259 /* 0x103 */,
+ HAL_WHO_COMMIT = 260 /* 0x104 */,
+ HAL_WHO_COMMIT_DONE = 261 /* 0x105 */,
+ HAL_WHO_FLUSH = 262 /* 0x106 */,
+ HAL_WHO_L2_LLC = 263 /* 0x107 */,
+ HAL_WHO_L2_PAYLOAD = 264 /* 0x108 */,
+ HAL_WHO_L3_CHECKSUM = 265 /* 0x109 */,
+ HAL_WHO_L3_INFO = 266 /* 0x10a */,
+ HAL_WHO_L4_CHECKSUM = 267 /* 0x10b */,
+ HAL_WHO_L4_INFO = 268 /* 0x10c */,
+ HAL_WHO_MSDU = 269 /* 0x10d */,
+ HAL_WHO_MSDU_MISC = 270 /* 0x10e */,
+ HAL_WHO_PACKET_DATA = 271 /* 0x10f */,
+ HAL_WHO_PACKET_HDR = 272 /* 0x110 */,
+ HAL_WHO_PPDU_END = 273 /* 0x111 */,
+ HAL_WHO_PPDU_START = 274 /* 0x112 */,
+ HAL_WHO_TSO = 275 /* 0x113 */,
+ HAL_WHO_WMAC_HEADER_PV0 = 276 /* 0x114 */,
+ HAL_WHO_WMAC_HEADER_PV1 = 277 /* 0x115 */,
+ HAL_WHO_WMAC_IV = 278 /* 0x116 */,
+ HAL_MPDU_INFO_END = 279 /* 0x117 */,
+ HAL_MPDU_INFO_BITMAP = 280 /* 0x118 */,
+ HAL_TX_QUEUE_EXTENSION = 281 /* 0x119 */,
+ HAL_RX_PEER_ENTRY_DETAILS = 282 /* 0x11a */,
+ HAL_RX_REO_QUEUE_REFERENCE = 283 /* 0x11b */,
+ HAL_RX_REO_QUEUE_EXT = 284 /* 0x11c */,
+ HAL_SCHEDULER_SELFGEN_RESPONSE_STATUS = 285 /* 0x11d */,
+ HAL_TQM_UPDATE_TX_MPDU_COUNT_STATUS = 286 /* 0x11e */,
+ HAL_TQM_ACKED_MPDU_STATUS = 287 /* 0x11f */,
+ HAL_TQM_ADD_MSDU_STATUS = 288 /* 0x120 */,
+ HAL_RX_MPDU_LINK_PTR = 289 /* 0x121 */,
+ HAL_REO_DESTINATION_RING = 290 /* 0x122 */,
+ HAL_TQM_LIST_GEN_DONE = 291 /* 0x123 */,
+ HAL_WHO_TERMINATE = 292 /* 0x124 */,
+ HAL_TX_LAST_MPDU_END = 293 /* 0x125 */,
+ HAL_TX_CV_DATA = 294 /* 0x126 */,
+ HAL_TCL_ENTRANCE_FROM_PPE_RING = 295 /* 0x127 */,
+ HAL_PPDU_TX_END = 296 /* 0x128 */,
+ HAL_PROT_TX_END = 297 /* 0x129 */,
+ HAL_PDG_RESPONSE_RATE_SETTING = 298 /* 0x12a */,
+ HAL_MPDU_INFO_GLOBAL_END = 299 /* 0x12b */,
+ HAL_TQM_SCH_INSTR_GLOBAL_END = 300 /* 0x12c */,
+ HAL_RX_PPDU_END_USER_STATS = 301 /* 0x12d */,
+ HAL_RX_PPDU_END_USER_STATS_EXT = 302 /* 0x12e */,
+ HAL_NO_ACK_REPORT = 303 /* 0x12f */,
+ HAL_ACK_REPORT = 304 /* 0x130 */,
+ HAL_UNIFORM_REO_CMD_HEADER = 305 /* 0x131 */,
+ HAL_REO_GET_QUEUE_STATS = 306 /* 0x132 */,
+ HAL_REO_FLUSH_QUEUE = 307 /* 0x133 */,
+ HAL_REO_FLUSH_CACHE = 308 /* 0x134 */,
+ HAL_REO_UNBLOCK_CACHE = 309 /* 0x135 */,
+ HAL_UNIFORM_REO_STATUS_HEADER = 310 /* 0x136 */,
+ HAL_REO_GET_QUEUE_STATS_STATUS = 311 /* 0x137 */,
+ HAL_REO_FLUSH_QUEUE_STATUS = 312 /* 0x138 */,
+ HAL_REO_FLUSH_CACHE_STATUS = 313 /* 0x139 */,
+ HAL_REO_UNBLOCK_CACHE_STATUS = 314 /* 0x13a */,
+ HAL_TQM_FLUSH_CACHE = 315 /* 0x13b */,
+ HAL_TQM_UNBLOCK_CACHE = 316 /* 0x13c */,
+ HAL_TQM_FLUSH_CACHE_STATUS = 317 /* 0x13d */,
+ HAL_TQM_UNBLOCK_CACHE_STATUS = 318 /* 0x13e */,
+ HAL_RX_PPDU_END_STATUS_DONE = 319 /* 0x13f */,
+ HAL_RX_STATUS_BUFFER_DONE = 320 /* 0x140 */,
+ HAL_BUFFER_ADDR_INFO = 321 /* 0x141 */,
+ HAL_RX_MSDU_DESC_INFO = 322 /* 0x142 */,
+ HAL_RX_MPDU_DESC_INFO = 323 /* 0x143 */,
+ HAL_TCL_DATA_CMD = 324 /* 0x144 */,
+ HAL_TCL_GSE_CMD = 325 /* 0x145 */,
+ HAL_TCL_EXIT_BASE = 326 /* 0x146 */,
+ HAL_TCL_COMPACT_EXIT_RING = 327 /* 0x147 */,
+ HAL_TCL_REGULAR_EXIT_RING = 328 /* 0x148 */,
+ HAL_TCL_EXTENDED_EXIT_RING = 329 /* 0x149 */,
+ HAL_UPLINK_COMMON_INFO = 330 /* 0x14a */,
+ HAL_UPLINK_USER_SETUP_INFO = 331 /* 0x14b */,
+ HAL_TX_DATA_SYNC = 332 /* 0x14c */,
+ HAL_PHYRX_CBF_READ_REQUEST_ACK = 333 /* 0x14d */,
+ HAL_TCL_STATUS_RING = 334 /* 0x14e */,
+ HAL_TQM_GET_MPDU_HEAD_INFO = 335 /* 0x14f */,
+ HAL_TQM_SYNC_CMD = 336 /* 0x150 */,
+ HAL_TQM_GET_MPDU_HEAD_INFO_STATUS = 337 /* 0x151 */,
+ HAL_TQM_SYNC_CMD_STATUS = 338 /* 0x152 */,
+ HAL_TQM_THRESHOLD_DROP_NOTIFICATION_STATUS = 339 /* 0x153 */,
+ HAL_TQM_DESCRIPTOR_THRESHOLD_REACHED_STATUS = 340 /* 0x154 */,
+ HAL_REO_FLUSH_TIMEOUT_LIST = 341 /* 0x155 */,
+ HAL_REO_FLUSH_TIMEOUT_LIST_STATUS = 342 /* 0x156 */,
+ HAL_REO_TO_PPE_RING = 343 /* 0x157 */,
+ HAL_RX_MPDU_INFO = 344 /* 0x158 */,
+ HAL_REO_DESCRIPTOR_THRESHOLD_REACHED_STATUS = 345 /* 0x159 */,
+ HAL_SCHEDULER_RX_SIFS_RESPONSE_TRIGGER_STATUS = 346 /* 0x15a */,
+ HAL_EXAMPLE_USER_TLV_32_NAME = 347 /* 0x15b */,
+ HAL_RX_PPDU_START_USER_INFO = 348 /* 0x15c */,
+ HAL_RX_RXPCU_CLASSIFICATION_OVERVIEW = 349 /* 0x15d */,
+ HAL_RX_RING_MASK = 350 /* 0x15e */,
+ HAL_WHO_CLASSIFY_INFO = 351 /* 0x15f */,
+ HAL_TXPT_CLASSIFY_INFO = 352 /* 0x160 */,
+ HAL_RXPT_CLASSIFY_INFO = 353 /* 0x161 */,
+ HAL_TX_FLOW_SEARCH_ENTRY = 354 /* 0x162 */,
+ HAL_RX_FLOW_SEARCH_ENTRY = 355 /* 0x163 */,
+ HAL_RECEIVED_TRIGGER_INFO_DETAILS = 356 /* 0x164 */,
+ HAL_COEX_MAC_NAP = 357 /* 0x165 */,
+ HAL_MACRX_ABORT_REQUEST_INFO = 358 /* 0x166 */,
+ HAL_MACTX_ABORT_REQUEST_INFO = 359 /* 0x167 */,
+ HAL_PHYRX_ABORT_REQUEST_INFO = 360 /* 0x168 */,
+ HAL_PHYTX_ABORT_REQUEST_INFO = 361 /* 0x169 */,
+ HAL_RXPCU_PPDU_END_INFO = 362 /* 0x16a */,
+ HAL_WHO_MESH_CONTROL = 363 /* 0x16b */,
+ HAL_L_SIG_A_INFO = 364 /* 0x16c */,
+ HAL_L_SIG_B_INFO = 365 /* 0x16d */,
+ HAL_HT_SIG_INFO = 366 /* 0x16e */,
+ HAL_VHT_SIG_A_INFO = 367 /* 0x16f */,
+ HAL_VHT_SIG_B_SU20_INFO = 368 /* 0x170 */,
+ HAL_VHT_SIG_B_SU40_INFO = 369 /* 0x171 */,
+ HAL_VHT_SIG_B_SU80_INFO = 370 /* 0x172 */,
+ HAL_VHT_SIG_B_SU160_INFO = 371 /* 0x173 */,
+ HAL_VHT_SIG_B_MU20_INFO = 372 /* 0x174 */,
+ HAL_VHT_SIG_B_MU40_INFO = 373 /* 0x175 */,
+ HAL_VHT_SIG_B_MU80_INFO = 374 /* 0x176 */,
+ HAL_VHT_SIG_B_MU160_INFO = 375 /* 0x177 */,
+ HAL_SERVICE_INFO = 376 /* 0x178 */,
+ HAL_HE_SIG_A_SU_INFO = 377 /* 0x179 */,
+ HAL_HE_SIG_A_MU_DL_INFO = 378 /* 0x17a */,
+ HAL_HE_SIG_A_MU_UL_INFO = 379 /* 0x17b */,
+ HAL_HE_SIG_B1_MU_INFO = 380 /* 0x17c */,
+ HAL_HE_SIG_B2_MU_INFO = 381 /* 0x17d */,
+ HAL_HE_SIG_B2_OFDMA_INFO = 382 /* 0x17e */,
+ HAL_PDG_SW_MODE_BW_START = 383 /* 0x17f */,
+ HAL_PDG_SW_MODE_BW_END = 384 /* 0x180 */,
+ HAL_PDG_WAIT_FOR_MAC_REQUEST = 385 /* 0x181 */,
+ HAL_PDG_WAIT_FOR_PHY_REQUEST = 386 /* 0x182 */,
+ HAL_SCHEDULER_END = 387 /* 0x183 */,
+ HAL_PEER_TABLE_ENTRY = 388 /* 0x184 */,
+ HAL_SW_PEER_INFO = 389 /* 0x185 */,
+ HAL_RXOLE_CCE_CLASSIFY_INFO = 390 /* 0x186 */,
+ HAL_TCL_CCE_CLASSIFY_INFO = 391 /* 0x187 */,
+ HAL_RXOLE_CCE_INFO = 392 /* 0x188 */,
+ HAL_TCL_CCE_INFO = 393 /* 0x189 */,
+ HAL_TCL_CCE_SUPERRULE = 394 /* 0x18a */,
+ HAL_CCE_RULE = 395 /* 0x18b */,
+ HAL_RX_PPDU_START_DROPPED = 396 /* 0x18c */,
+ HAL_RX_PPDU_END_DROPPED = 397 /* 0x18d */,
+ HAL_RX_PPDU_END_STATUS_DONE_DROPPED = 398 /* 0x18e */,
+ HAL_RX_MPDU_START_DROPPED = 399 /* 0x18f */,
+ HAL_RX_MSDU_START_DROPPED = 400 /* 0x190 */,
+ HAL_RX_MSDU_END_DROPPED = 401 /* 0x191 */,
+ HAL_RX_MPDU_END_DROPPED = 402 /* 0x192 */,
+ HAL_RX_ATTENTION_DROPPED = 403 /* 0x193 */,
+ HAL_TXPCU_USER_SETUP = 404 /* 0x194 */,
+ HAL_RXPCU_USER_SETUP_EXT = 405 /* 0x195 */,
+ HAL_CE_SRC_DESC = 406 /* 0x196 */,
+ HAL_CE_STAT_DESC = 407 /* 0x197 */,
+ HAL_RXOLE_CCE_SUPERRULE = 408 /* 0x198 */,
+ HAL_TX_RATE_STATS_INFO = 409 /* 0x199 */,
+ HAL_CMD_PART_0_END = 410 /* 0x19a */,
+ HAL_MACTX_SYNTH_ON = 411 /* 0x19b */,
+ HAL_SCH_CRITICAL_TLV_REFERENCE = 412 /* 0x19c */,
+ HAL_TQM_MPDU_GLOBAL_START = 413 /* 0x19d */,
+ HAL_EXAMPLE_TLV_32 = 414 /* 0x19e */,
+ HAL_TQM_UPDATE_TX_MSDU_FLOW = 415 /* 0x19f */,
+ HAL_TQM_UPDATE_TX_MPDU_QUEUE_HEAD = 416 /* 0x1a0 */,
+ HAL_TQM_UPDATE_TX_MSDU_FLOW_STATUS = 417 /* 0x1a1 */,
+ HAL_TQM_UPDATE_TX_MPDU_QUEUE_HEAD_STATUS = 418 /* 0x1a2 */,
+ HAL_REO_UPDATE_RX_REO_QUEUE = 419 /* 0x1a3 */,
+ HAL_CE_DST_DESC = 420 /* 0x1a4 */,
+ HAL_TLV_BASE = 511 /* 0x1ff */,
+};
+
+#define HAL_TLV_HDR_TAG GENMASK(9, 1)
+#define HAL_TLV_HDR_LEN GENMASK(25, 10)
+
+#define HAL_TLV_ALIGN 4
+
+struct hal_tlv_hdr {
+ u32 tl;
+ u8 value[0];
+} __packed;
+
+#define RX_MPDU_DESC_INFO0_MSDU_COUNT GENMASK(7, 0)
+#define RX_MPDU_DESC_INFO0_SEQ_NUM GENMASK(19, 8)
+#define RX_MPDU_DESC_INFO0_FRAG_FLAG BIT(20)
+#define RX_MPDU_DESC_INFO0_MPDU_RETRY BIT(21)
+#define RX_MPDU_DESC_INFO0_AMPDU_FLAG BIT(22)
+#define RX_MPDU_DESC_INFO0_BAR_FRAME BIT(23)
+#define RX_MPDU_DESC_INFO0_VALID_PN BIT(24)
+#define RX_MPDU_DESC_INFO0_VALID_SA BIT(25)
+#define RX_MPDU_DESC_INFO0_SA_IDX_TIMEOUT BIT(26)
+#define RX_MPDU_DESC_INFO0_VALID_DA BIT(27)
+#define RX_MPDU_DESC_INFO0_DA_MCBC BIT(28)
+#define RX_MPDU_DESC_INFO0_DA_IDX_TIMEOUT BIT(29)
+#define RX_MPDU_DESC_INFO0_RAW_MPDU BIT(30)
+
+struct rx_mpdu_desc {
+ u32 info0; /* %RX_MPDU_DESC_INFO */
+ u32 meta_data;
+} __packed;
+
+/* rx_mpdu_desc
+ * Producer: RXDMA
+ * Consumer: REO/SW/FW
+ *
+ * msdu_count
+ * The number of MSDUs within the MPDU
+ *
+ * mpdu_sequence_number
+ * The field can have two different meanings based on the setting
+ * of field 'bar_frame'. If 'bar_frame' is set, it means the MPDU
+ * start sequence number from the BAR frame otherwise it means
+ * the MPDU sequence number of the received frame.
+ *
+ * fragment_flag
+ * When set, this MPDU is a fragment and REO should forward this
+ * fragment MPDU to the REO destination ring without any reorder
+ * checks, pn checks or bitmap update. This implies that REO is
+ * forwarding the pointer to the MSDU link descriptor.
+ *
+ * mpdu_retry_bit
+ * The retry bit setting from the MPDU header of the received frame
+ *
+ * ampdu_flag
+ * Indicates the MPDU was received as part of an A-MPDU.
+ *
+ * bar_frame
+ * Indicates the received frame is a BAR frame. After processing,
+ * this frame shall be pushed to SW or deleted.
+ *
+ * valid_pn
+ * When not set, REO will not perform a PN sequence number check.
+ *
+ * valid_sa
+ * Indicates OLE found a valid SA entry for all MSDUs in this MPDU.
+ *
+ * sa_idx_timeout
+ * Indicates, at least 1 MSDU within the MPDU has an unsuccessful
+ * MAC source address search due to the expiration of search timer.
+ *
+ * valid_da
+ * When set, OLE found a valid DA entry for all MSDUs in this MPDU.
+ *
+ * da_mcbc
+ * Field Only valid if valid_da is set. Indicates at least one of
+ * the DA addresses is a Multicast or Broadcast address.
+ *
+ * da_idx_timeout
+ * Indicates, at least 1 MSDU within the MPDU has an unsuccessful
+ * MAC destination address search due to the expiration of search
+ * timer.
+ *
+ * raw_mpdu
+ * Field only valid when first_msdu_in_mpdu_flag is set. Indicates
+ * the contents in the MSDU buffer contains a 'RAW' MPDU.
+ */
+
+enum hal_rx_msdu_desc_reo_dest_ind {
+ HAL_RX_MSDU_DESC_REO_DEST_IND_TCL,
+ HAL_RX_MSDU_DESC_REO_DEST_IND_SW1,
+ HAL_RX_MSDU_DESC_REO_DEST_IND_SW2,
+ HAL_RX_MSDU_DESC_REO_DEST_IND_SW3,
+ HAL_RX_MSDU_DESC_REO_DEST_IND_SW4,
+ HAL_RX_MSDU_DESC_REO_DEST_IND_RELEASE,
+ HAL_RX_MSDU_DESC_REO_DEST_IND_FW,
+};
+
+#define RX_MSDU_DESC_INFO0_FIRST_MSDU_IN_MPDU BIT(0)
+#define RX_MSDU_DESC_INFO0_LAST_MSDU_IN_MPDU BIT(1)
+#define RX_MSDU_DESC_INFO0_MSDU_CONTINUATION BIT(2)
+#define RX_MSDU_DESC_INFO0_MSDU_LENGTH GENMASK(16, 3)
+#define RX_MSDU_DESC_INFO0_REO_DEST_IND GENMASK(21, 17)
+#define RX_MSDU_DESC_INFO0_MSDU_DROP BIT(22)
+#define RX_MSDU_DESC_INFO0_VALID_SA BIT(23)
+#define RX_MSDU_DESC_INFO0_SA_IDX_TIMEOUT BIT(24)
+#define RX_MSDU_DESC_INFO0_VALID_DA BIT(25)
+#define RX_MSDU_DESC_INFO0_DA_MCBC BIT(26)
+#define RX_MSDU_DESC_INFO0_DA_IDX_TIMEOUT BIT(27)
+
+#define HAL_RX_MSDU_PKT_LENGTH_GET(val) \
+ (FIELD_GET(RX_MSDU_DESC_INFO0_MSDU_LENGTH, (val)))
+
+struct rx_msdu_desc {
+ u32 info0;
+ u32 rsvd0;
+} __packed;
+
+/* rx_msdu_desc
+ *
+ * first_msdu_in_mpdu
+ * Indicates first msdu in mpdu.
+ *
+ * last_msdu_in_mpdu
+ * Indicates last msdu in mpdu. This flag can be true only when
+ * 'Msdu_continuation' set to 0. This implies that when an msdu
+ * is spread out over multiple buffers and thus msdu_continuation
+ * is set, only for the very last buffer of the msdu, can the
+ * 'last_msdu_in_mpdu' be set.
+ *
+ * When both first_msdu_in_mpdu and last_msdu_in_mpdu are set,
+ * the MPDU that this MSDU belongs to only contains a single MSDU.
+ *
+ * msdu_continuation
+ * When set, this MSDU buffer was not able to hold the entire MSDU.
+ * The next buffer will therefor contain additional information
+ * related to this MSDU.
+ *
+ * msdu_length
+ * Field is only valid in combination with the 'first_msdu_in_mpdu'
+ * being set. Full MSDU length in bytes after decapsulation. This
+ * field is still valid for MPDU frames without A-MSDU. It still
+ * represents MSDU length after decapsulation Or in case of RAW
+ * MPDUs, it indicates the length of the entire MPDU (without FCS
+ * field).
+ *
+ * reo_destination_indication
+ * The id of the reo exit ring where the msdu frame shall push
+ * after (MPDU level) reordering has finished. Values are defined
+ * in enum %HAL_RX_MSDU_DESC_REO_DEST_IND_.
+ *
+ * msdu_drop
+ * Indicates that REO shall drop this MSDU and not forward it to
+ * any other ring.
+ *
+ * valid_sa
+ * Indicates OLE found a valid SA entry for this MSDU.
+ *
+ * sa_idx_timeout
+ * Indicates, an unsuccessful MAC source address search due to
+ * the expiration of search timer for this MSDU.
+ *
+ * valid_da
+ * When set, OLE found a valid DA entry for this MSDU.
+ *
+ * da_mcbc
+ * Field Only valid if valid_da is set. Indicates the DA address
+ * is a Multicast or Broadcast address for this MSDU.
+ *
+ * da_idx_timeout
+ * Indicates, an unsuccessful MAC destination address search due
+ * to the expiration of search timer fot this MSDU.
+ */
+
+enum hal_reo_dest_ring_buffer_type {
+ HAL_REO_DEST_RING_BUFFER_TYPE_MSDU,
+ HAL_REO_DEST_RING_BUFFER_TYPE_LINK_DESC,
+};
+
+enum hal_reo_dest_ring_push_reason {
+ HAL_REO_DEST_RING_PUSH_REASON_ERR_DETECTED,
+ HAL_REO_DEST_RING_PUSH_REASON_ROUTING_INSTRUCTION,
+};
+
+enum hal_reo_dest_ring_error_code {
+ HAL_REO_DEST_RING_ERROR_CODE_DESC_ADDR_ZERO,
+ HAL_REO_DEST_RING_ERROR_CODE_DESC_INVALID,
+ HAL_REO_DEST_RING_ERROR_CODE_AMPDU_IN_NON_BA,
+ HAL_REO_DEST_RING_ERROR_CODE_NON_BA_DUPLICATE,
+ HAL_REO_DEST_RING_ERROR_CODE_BA_DUPLICATE,
+ HAL_REO_DEST_RING_ERROR_CODE_FRAME_2K_JUMP,
+ HAL_REO_DEST_RING_ERROR_CODE_BAR_2K_JUMP,
+ HAL_REO_DEST_RING_ERROR_CODE_FRAME_OOR,
+ HAL_REO_DEST_RING_ERROR_CODE_BAR_OOR,
+ HAL_REO_DEST_RING_ERROR_CODE_NO_BA_SESSION,
+ HAL_REO_DEST_RING_ERROR_CODE_FRAME_SN_EQUALS_SSN,
+ HAL_REO_DEST_RING_ERROR_CODE_PN_CHECK_FAILED,
+ HAL_REO_DEST_RING_ERROR_CODE_2K_ERR_FLAG_SET,
+ HAL_REO_DEST_RING_ERROR_CODE_PN_ERR_FLAG_SET,
+ HAL_REO_DEST_RING_ERROR_CODE_DESC_BLOCKED,
+ HAL_REO_DEST_RING_ERROR_CODE_MAX,
+};
+
+#define HAL_REO_DEST_RING_INFO0_QUEUE_ADDR_HI GENMASK(7, 0)
+#define HAL_REO_DEST_RING_INFO0_BUFFER_TYPE BIT(8)
+#define HAL_REO_DEST_RING_INFO0_PUSH_REASON GENMASK(10, 9)
+#define HAL_REO_DEST_RING_INFO0_ERROR_CODE GENMASK(15, 11)
+#define HAL_REO_DEST_RING_INFO0_RX_QUEUE_NUM GENMASK(31, 16)
+
+#define HAL_REO_DEST_RING_INFO1_REORDER_INFO_VALID BIT(0)
+#define HAL_REO_DEST_RING_INFO1_REORDER_OPCODE GENMASK(4, 1)
+#define HAL_REO_DEST_RING_INFO1_REORDER_SLOT_IDX GENMASK(12, 5)
+
+#define HAL_REO_DEST_RING_INFO2_RING_ID GENMASK(27, 20)
+#define HAL_REO_DEST_RING_INFO2_LOOPING_COUNT GENMASK(31, 28)
+
+struct hal_reo_dest_ring {
+ struct ath11k_buffer_addr buf_addr_info;
+ struct rx_mpdu_desc rx_mpdu_info;
+ struct rx_msdu_desc rx_msdu_info;
+ u32 queue_addr_lo;
+ u32 info0; /* %HAL_REO_DEST_RING_INFO0_ */
+ u32 info1; /* %HAL_REO_DEST_RING_INFO1_ */
+ u32 rsvd0;
+ u32 rsvd1;
+ u32 rsvd2;
+ u32 rsvd3;
+ u32 rsvd4;
+ u32 rsvd5;
+ u32 info2; /* %HAL_REO_DEST_RING_INFO2_ */
+} __packed;
+
+/* hal_reo_dest_ring
+ *
+ * Producer: RXDMA
+ * Consumer: REO/SW/FW
+ *
+ * buf_addr_info
+ * Details of the physical address of a buffer or MSDU
+ * link descriptor.
+ *
+ * rx_mpdu_info
+ * General information related to the MPDU that is passed
+ * on from REO entrance ring to the REO destination ring.
+ *
+ * rx_msdu_info
+ * General information related to the MSDU that is passed
+ * on from RXDMA all the way to to the REO destination ring.
+ *
+ * queue_addr_lo
+ * Address (lower 32 bits) of the REO queue descriptor.
+ *
+ * queue_addr_hi
+ * Address (upper 8 bits) of the REO queue descriptor.
+ *
+ * buffer_type
+ * Indicates the type of address provided in the buf_addr_info.
+ * Values are defined in enum %HAL_REO_DEST_RING_BUFFER_TYPE_.
+ *
+ * push_reason
+ * Reason for pushing this frame to this exit ring. Values are
+ * defined in enum %HAL_REO_DEST_RING_PUSH_REASON_.
+ *
+ * error_code
+ * Valid only when 'push_reason' is set. All error codes are
+ * defined in enum %HAL_REO_DEST_RING_ERROR_CODE_.
+ *
+ * rx_queue_num
+ * Indicates the REO MPDU reorder queue id from which this frame
+ * originated.
+ *
+ * reorder_info_valid
+ * When set, REO has been instructed to not perform the actual
+ * re-ordering of frames for this queue, but just to insert
+ * the reorder opcodes.
+ *
+ * reorder_opcode
+ * Field is valid when 'reorder_info_valid' is set. This field is
+ * always valid for debug purpose as well.
+ *
+ * reorder_slot_idx
+ * Valid only when 'reorder_info_valid' is set.
+ *
+ * ring_id
+ * The buffer pointer ring id.
+ * 0 - Idle ring
+ * 1 - N refers to other rings.
+ *
+ * looping_count
+ * Indicates the number of times the producer of entries into
+ * this ring has looped around the ring.
+ */
+
+enum hal_reo_entr_rxdma_ecode {
+ HAL_REO_ENTR_RING_RXDMA_ECODE_OVERFLOW_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_MPDU_LEN_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_FCS_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_DECRYPT_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_TKIP_MIC_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_UNECRYPTED_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_MSDU_LEN_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_MSDU_LIMIT_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_WIFI_PARSE_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_AMSDU_PARSE_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_SA_TIMEOUT_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_DA_TIMEOUT_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_FLOW_TIMEOUT_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_FLUSH_REQUEST_ERR,
+ HAL_REO_ENTR_RING_RXDMA_ECODE_MAX,
+};
+
+#define HAL_REO_ENTR_RING_INFO0_QUEUE_ADDR_HI GENMASK(7, 0)
+#define HAL_REO_ENTR_RING_INFO0_MPDU_BYTE_COUNT GENMASK(21, 8)
+#define HAL_REO_ENTR_RING_INFO0_DEST_IND GENMASK(26, 22)
+#define HAL_REO_ENTR_RING_INFO0_FRAMELESS_BAR BIT(27)
+
+#define HAL_REO_ENTR_RING_INFO1_RXDMA_PUSH_REASON GENMASK(1, 0)
+#define HAL_REO_ENTR_RING_INFO1_RXDMA_ERROR_CODE GENMASK(6, 2)
+
+struct hal_reo_entrance_ring {
+ struct ath11k_buffer_addr buf_addr_info;
+ struct rx_mpdu_desc rx_mpdu_info;
+ u32 queue_addr_lo;
+ u32 info0; /* %HAL_REO_ENTR_RING_INFO0_ */
+ u32 info1; /* %HAL_REO_ENTR_RING_INFO1_ */
+ u32 info2; /* %HAL_REO_DEST_RING_INFO2_ */
+
+} __packed;
+
+/* hal_reo_entrance_ring
+ *
+ * Producer: RXDMA
+ * Consumer: REO
+ *
+ * buf_addr_info
+ * Details of the physical address of a buffer or MSDU
+ * link descriptor.
+ *
+ * rx_mpdu_info
+ * General information related to the MPDU that is passed
+ * on from REO entrance ring to the REO destination ring.
+ *
+ * queue_addr_lo
+ * Address (lower 32 bits) of the REO queue descriptor.
+ *
+ * queue_addr_hi
+ * Address (upper 8 bits) of the REO queue descriptor.
+ *
+ * mpdu_byte_count
+ * An approximation of the number of bytes received in this MPDU.
+ * Used to keeps stats on the amount of data flowing
+ * through a queue.
+ *
+ * reo_destination_indication
+ * The id of the reo exit ring where the msdu frame shall push
+ * after (MPDU level) reordering has finished. Values are defined
+ * in enum %HAL_RX_MSDU_DESC_REO_DEST_IND_.
+ *
+ * frameless_bar
+ * Indicates that this REO entrance ring struct contains BAR info
+ * from a multi TID BAR frame. The original multi TID BAR frame
+ * itself contained all the REO info for the first TID, but all
+ * the subsequent TID info and their linkage to the REO descriptors
+ * is passed down as 'frameless' BAR info.
+ *
+ * The only fields valid in this descriptor when this bit is set
+ * are queue_addr_lo, queue_addr_hi, mpdu_sequence_number,
+ * bar_frame and peer_meta_data.
+ *
+ * rxdma_push_reason
+ * Reason for pushing this frame to this exit ring. Values are
+ * defined in enum %HAL_REO_DEST_RING_PUSH_REASON_.
+ *
+ * rxdma_error_code
+ * Valid only when 'push_reason' is set. All error codes are
+ * defined in enum %HAL_REO_ENTR_RING_RXDMA_ECODE_.
+ *
+ * ring_id
+ * The buffer pointer ring id.
+ * 0 - Idle ring
+ * 1 - N refers to other rings.
+ *
+ * looping_count
+ * Indicates the number of times the producer of entries into
+ * this ring has looped around the ring.
+ */
+
+#define HAL_REO_CMD_HDR_INFO0_CMD_NUMBER GENMASK(15, 0)
+#define HAL_REO_CMD_HDR_INFO0_STATUS_REQUIRED BIT(16)
+
+struct hal_reo_cmd_hdr {
+ u32 info0;
+} __packed;
+
+#define HAL_REO_GET_QUEUE_STATS_INFO0_QUEUE_ADDR_HI GENMASK(7, 0)
+#define HAL_REO_GET_QUEUE_STATS_INFO0_CLEAR_STATS BIT(8)
+
+struct hal_reo_get_queue_stats {
+ struct hal_reo_cmd_hdr cmd;
+ u32 queue_addr_lo;
+ u32 info0;
+ u32 rsvd0[6];
+} __packed;
+
+/* hal_reo_get_queue_stats
+ * Producer: SW
+ * Consumer: REO
+ *
+ * cmd
+ * Details for command execution tracking purposes.
+ *
+ * queue_addr_lo
+ * Address (lower 32 bits) of the REO queue descriptor.
+ *
+ * queue_addr_hi
+ * Address (upper 8 bits) of the REO queue descriptor.
+ *
+ * clear_stats
+ * Clear stats settings. When set, Clear the stats after
+ * generating the status.
+ *
+ * Following stats will be cleared.
+ * Timeout_count
+ * Forward_due_to_bar_count
+ * Duplicate_count
+ * Frames_in_order_count
+ * BAR_received_count
+ * MPDU_Frames_processed_count
+ * MSDU_Frames_processed_count
+ * Total_processed_byte_count
+ * Late_receive_MPDU_count
+ * window_jump_2k
+ * Hole_count
+ */
+
+#define HAL_REO_FLUSH_QUEUE_INFO0_DESC_ADDR_HI GENMASK(7, 0)
+#define HAL_REO_FLUSH_QUEUE_INFO0_BLOCK_DESC_ADDR BIT(8)
+#define HAL_REO_FLUSH_QUEUE_INFO0_BLOCK_RESRC_IDX GENMASK(10, 9)
+
+struct hal_reo_flush_queue {
+ struct hal_reo_cmd_hdr cmd;
+ u32 desc_addr_lo;
+ u32 info0;
+ u32 rsvd0[6];
+} __packed;
+
+#define HAL_REO_FLUSH_CACHE_INFO0_CACHE_ADDR_HI GENMASK(7, 0)
+#define HAL_REO_FLUSH_CACHE_INFO0_FWD_ALL_MPDUS BIT(8)
+#define HAL_REO_FLUSH_CACHE_INFO0_RELEASE_BLOCK_IDX BIT(9)
+#define HAL_REO_FLUSH_CACHE_INFO0_BLOCK_RESRC_IDX GENMASK(11, 10)
+#define HAL_REO_FLUSH_CACHE_INFO0_FLUSH_WO_INVALIDATE BIT(12)
+#define HAL_REO_FLUSH_CACHE_INFO0_BLOCK_CACHE_USAGE BIT(13)
+#define HAL_REO_FLUSH_CACHE_INFO0_FLUSH_ALL BIT(14)
+
+struct hal_reo_flush_cache {
+ struct hal_reo_cmd_hdr cmd;
+ u32 cache_addr_lo;
+ u32 info0;
+ u32 rsvd0[6];
+} __packed;
+
+#define HAL_TCL_DATA_CMD_INFO0_DESC_TYPE BIT(0)
+#define HAL_TCL_DATA_CMD_INFO0_EPD BIT(1)
+#define HAL_TCL_DATA_CMD_INFO0_ENCAP_TYPE GENMASK(3, 2)
+#define HAL_TCL_DATA_CMD_INFO0_ENCRYPT_TYPE GENMASK(7, 4)
+#define HAL_TCL_DATA_CMD_INFO0_SRC_BUF_SWAP BIT(8)
+#define HAL_TCL_DATA_CMD_INFO0_LNK_META_SWAP BIT(9)
+#define HAL_TCL_DATA_CMD_INFO0_SEARCH_TYPE BIT(12)
+#define HAL_TCL_DATA_CMD_INFO0_ADDRX_EN BIT(14)
+#define HAL_TCL_DATA_CMD_INFO0_ADDRY_EN BIT(15)
+#define HAL_TCL_DATA_CMD_INFO0_CMD_NUM GENMASK(31, 16)
+
+#define HAL_TCL_DATA_CMD_INFO1_DATA_LEN GENMASK(15, 0)
+#define HAL_TCL_DATA_CMD_INFO1_IP4_CKSUM_EN BIT(16)
+#define HAL_TCL_DATA_CMD_INFO1_UDP4_CKSUM_EN BIT(17)
+#define HAL_TCL_DATA_CMD_INFO1_UDP6_CKSUM_EN BIT(18)
+#define HAL_TCL_DATA_CMD_INFO1_TCP4_CKSUM_EN BIT(19)
+#define HAL_TCL_DATA_CMD_INFO1_TCP6_CKSUM_EN BIT(20)
+#define HAL_TCL_DATA_CMD_INFO1_TO_FW BIT(21)
+#define HAL_TCL_DATA_CMD_INFO1_PKT_OFFSET GENMASK(31, 23)
+
+#define HAL_TCL_DATA_CMD_INFO2_BUF_TIMESTAMP GENMASK(18, 0)
+#define HAL_TCL_DATA_CMD_INFO2_BUF_T_VALID BIT(19)
+#define HAL_TCL_DATA_CMD_INFO2_MESH_ENABLE BIT(20)
+#define HAL_TCL_DATA_CMD_INFO2_TID_OVERWRITE BIT(21)
+#define HAL_TCL_DATA_CMD_INFO2_TID GENMASK(25, 22)
+#define HAL_TCL_DATA_CMD_INFO2_LMAC_ID GENMASK(27, 26)
+
+#define HAL_TCL_DATA_CMD_INFO3_DSCP_TID_TABLE_IDX GENMASK(5, 0)
+#define HAL_TCL_DATA_CMD_INFO3_SEARCH_INDEX GENMASK(25, 6)
+#define HAL_TCL_DATA_CMD_INFO3_CACHE_SET_NUM GENMASK(29, 26)
+
+#define HAL_TCL_DATA_CMD_INFO4_RING_ID GENMASK(27, 20)
+#define HAL_TCL_DATA_CMD_INFO4_LOOPING_COUNT GENMASK(31, 28)
+
+enum hal_encrypt_type {
+ HAL_ENCRYPT_TYPE_WEP_40,
+ HAL_ENCRYPT_TYPE_WEP_104,
+ HAL_ENCRYPT_TYPE_TKIP_NO_MIC,
+ HAL_ENCRYPT_TYPE_WEP_128,
+ HAL_ENCRYPT_TYPE_TKIP_MIC,
+ HAL_ENCRYPT_TYPE_WAPI,
+ HAL_ENCRYPT_TYPE_CCMP_128,
+ HAL_ENCRYPT_TYPE_OPEN,
+ HAL_ENCRYPT_TYPE_CCMP_256,
+ HAL_ENCRYPT_TYPE_GCMP_128,
+ HAL_ENCRYPT_TYPE_AES_GCMP_256,
+ HAL_ENCRYPT_TYPE_WAPI_GCM_SM4,
+};
+
+enum hal_tcl_encap_type {
+ HAL_TCL_ENCAP_TYPE_RAW,
+ HAL_TCL_ENCAP_TYPE_NATIVE_WIFI,
+ HAL_TCL_ENCAP_TYPE_ETHERNET,
+ HAL_TCL_ENCAP_TYPE_802_3 = 3,
+};
+
+enum hal_tcl_desc_type {
+ HAL_TCL_DESC_TYPE_BUFFER,
+ HAL_TCL_DESC_TYPE_EXT_DESC,
+};
+
+enum hal_wbm_htt_tx_comp_status {
+ HAL_WBM_REL_HTT_TX_COMP_STATUS_OK,
+ HAL_WBM_REL_HTT_TX_COMP_STATUS_DROP,
+ HAL_WBM_REL_HTT_TX_COMP_STATUS_TTL,
+ HAL_WBM_REL_HTT_TX_COMP_STATUS_REINJ,
+ HAL_WBM_REL_HTT_TX_COMP_STATUS_INSPECT,
+ HAL_WBM_REL_HTT_TX_COMP_STATUS_MEC_NOTIFY,
+};
+
+struct hal_tcl_data_cmd {
+ struct ath11k_buffer_addr buf_addr_info;
+ u32 info0;
+ u32 info1;
+ u32 info2;
+ u32 info3;
+ u32 info4;
+} __packed;
+
+/* hal_tcl_data_cmd
+ *
+ * buf_addr_info
+ * Details of the physical address of a buffer or MSDU
+ * link descriptor.
+ *
+ * desc_type
+ * Indicates the type of address provided in the buf_addr_info.
+ * Values are defined in enum %HAL_REO_DEST_RING_BUFFER_TYPE_.
+ *
+ * epd
+ * When this bit is set then input packet is an EPD type.
+ *
+ * encap_type
+ * Indicates the encapsulation that HW will perform. Values are
+ * defined in enum %HAL_TCL_ENCAP_TYPE_.
+ *
+ * encrypt_type
+ * Field only valid for encap_type: RAW
+ * Values are defined in enum %HAL_ENCRYPT_TYPE_.
+ *
+ * src_buffer_swap
+ * Treats source memory (packet buffer) organization as big-endian.
+ * 1'b0: Source memory is little endian
+ * 1'b1: Source memory is big endian
+ *
+ * link_meta_swap
+ * Treats link descriptor and Metadata as big-endian.
+ * 1'b0: memory is little endian
+ * 1'b1: memory is big endian
+ *
+ * search_type
+ * Search type select
+ * 0 - Normal search, 1 - Index based address search,
+ * 2 - Index based flow search
+ *
+ * addrx_en
+ * addry_en
+ * Address X/Y search enable in ASE correspondingly.
+ * 1'b0: Search disable
+ * 1'b1: Search Enable
+ *
+ * cmd_num
+ * This number can be used to match against status.
+ *
+ * data_length
+ * MSDU length in case of direct descriptor. Length of link
+ * extension descriptor in case of Link extension descriptor.
+ *
+ * *_checksum_en
+ * Enable checksum replacement for ipv4, udp_over_ipv4, ipv6,
+ * udp_over_ipv6, tcp_over_ipv4 and tcp_over_ipv6.
+ *
+ * to_fw
+ * Forward packet to FW along with classification result. The
+ * packet will not be forward to TQM when this bit is set.
+ * 1'b0: Use classification result to forward the packet.
+ * 1'b1: Override classification result & forward packet only to fw
+ *
+ * packet_offset
+ * Packet offset from Metadata in case of direct buffer descriptor.
+ *
+ * buffer_timestamp
+ * buffer_timestamp_valid
+ * Frame system entrance timestamp. It shall be filled by first
+ * module (SW, TCL or TQM) that sees the frames first.
+ *
+ * mesh_enable
+ * For raw WiFi frames, this indicates transmission to a mesh STA,
+ * enabling the interpretation of the 'Mesh Control Present' bit
+ * (bit 8) of QoS Control.
+ * For native WiFi frames, this indicates that a 'Mesh Control'
+ * field is present between the header and the LLC.
+ *
+ * hlos_tid_overwrite
+ *
+ * When set, TCL shall ignore the IP DSCP and VLAN PCP
+ * fields and use HLOS_TID as the final TID. Otherwise TCL
+ * shall consider the DSCP and PCP fields as well as HLOS_TID
+ * and choose a final TID based on the configured priority
+ *
+ * hlos_tid
+ * HLOS MSDU priority
+ * Field is used when HLOS_TID_overwrite is set.
+ *
+ * lmac_id
+ * TCL uses this LMAC_ID in address search, i.e, while
+ * finding matching entry for the packet in AST corresponding
+ * to given LMAC_ID
+ *
+ * If LMAC ID is all 1s (=> value 3), it indicates wildcard
+ * match for any MAC
+ *
+ * dscp_tid_table_num
+ * DSCP to TID mapping table number that need to be used
+ * for the MSDU.
+ *
+ * search_index
+ * The index that will be used for index based address or
+ * flow search. The field is valid when 'search_type' is 1 or 2.
+ *
+ * cache_set_num
+ *
+ * Cache set number that should be used to cache the index
+ * based search results, for address and flow search. This
+ * value should be equal to LSB four bits of the hash value of
+ * match data, in case of search index points to an entry which
+ * may be used in content based search also. The value can be
+ * anything when the entry pointed by search index will not be
+ * used for content based search.
+ *
+ * ring_id
+ * The buffer pointer ring ID.
+ * 0 refers to the IDLE ring
+ * 1 - N refers to other rings
+ *
+ * looping_count
+ *
+ * A count value that indicates the number of times the
+ * producer of entries into the Ring has looped around the
+ * ring.
+ *
+ * At initialization time, this value is set to 0. On the
+ * first loop, this value is set to 1. After the max value is
+ * reached allowed by the number of bits for this field, the
+ * count value continues with 0 again.
+ *
+ * In case SW is the consumer of the ring entries, it can
+ * use this field to figure out up to where the producer of
+ * entries has created new entries. This eliminates the need to
+ * check where the head pointer' of the ring is located once
+ * the SW starts processing an interrupt indicating that new
+ * entries have been put into this ring...
+ *
+ * Also note that SW if it wants only needs to look at the
+ * LSB bit of this count value.
+ */
+
+#define HAL_TCL_DESC_LEN sizeof(struct hal_tcl_data_cmd)
+
+enum hal_tcl_gse_ctrl {
+ HAL_TCL_GSE_CTRL_RD_STAT,
+ HAL_TCL_GSE_CTRL_SRCH_DIS,
+ HAL_TCL_GSE_CTRL_WR_BK_SINGLE,
+ HAL_TCL_GSE_CTRL_WR_BK_ALL,
+ HAL_TCL_GSE_CTRL_INVAL_SINGLE,
+ HAL_TCL_GSE_CTRL_INVAL_ALL,
+ HAL_TCL_GSE_CTRL_WR_BK_INVAL_SINGLE,
+ HAL_TCL_GSE_CTRL_WR_BK_INVAL_ALL,
+ HAL_TCL_GSE_CTRL_CLR_STAT_SINGLE,
+};
+
+/* hal_tcl_gse_ctrl
+ *
+ * rd_stat
+ * Report or Read statistics
+ * srch_dis
+ * Search disable. Report only Hash.
+ * wr_bk_single
+ * Write Back single entry
+ * wr_bk_all
+ * Write Back entire cache entry
+ * inval_single
+ * Invalidate single cache entry
+ * inval_all
+ * Invalidate entire cache
+ * wr_bk_inval_single
+ * Write back and invalidate single entry in cache
+ * wr_bk_inval_all
+ * Write back and invalidate entire cache
+ * clr_stat_single
+ * Clear statistics for single entry
+ */
+
+#define HAL_TCL_GSE_CMD_INFO0_CTRL_BUF_ADDR_HI GENMASK(7, 0)
+#define HAL_TCL_GSE_CMD_INFO0_GSE_CTRL GENMASK(11, 8)
+#define HAL_TCL_GSE_CMD_INFO0_GSE_SEL BIT(12)
+#define HAL_TCL_GSE_CMD_INFO0_STATUS_DEST_RING_ID BIT(13)
+#define HAL_TCL_GSE_CMD_INFO0_SWAP BIT(14)
+
+#define HAL_TCL_GSE_CMD_INFO1_RING_ID GENMASK(27, 20)
+#define HAL_TCL_GSE_CMD_INFO1_LOOPING_COUNT GENMASK(31, 28)
+
+struct hal_tcl_gse_cmd {
+ u32 ctrl_buf_addr_lo;
+ u32 info0;
+ u32 meta_data[2];
+ u32 rsvd0[2];
+ u32 info1;
+} __packed;
+
+/* hal_tcl_gse_cmd
+ *
+ * ctrl_buf_addr_lo, ctrl_buf_addr_hi
+ * Address of a control buffer containing additional info needed
+ * for this command execution.
+ *
+ * gse_ctrl
+ * GSE control operations. This includes cache operations and table
+ * entry statistics read/clear operation. Values are defined in
+ * enum %HAL_TCL_GSE_CTRL.
+ *
+ * gse_sel
+ * To select the ASE/FSE to do the operation mention by GSE_ctrl.
+ * 0: FSE select 1: ASE select
+ *
+ * status_destination_ring_id
+ * TCL status ring to which the GSE status needs to be send.
+ *
+ * swap
+ * Bit to enable byte swapping of contents of buffer.
+ *
+ * meta_data
+ * Meta data to be returned in the status descriptor
+ */
+
+enum hal_tcl_cache_op_res {
+ HAL_TCL_CACHE_OP_RES_DONE,
+ HAL_TCL_CACHE_OP_RES_NOT_FOUND,
+ HAL_TCL_CACHE_OP_RES_TIMEOUT,
+};
+
+#define HAL_TCL_STATUS_RING_INFO0_GSE_CTRL GENMASK(3, 0)
+#define HAL_TCL_STATUS_RING_INFO0_GSE_SEL BIT(4)
+#define HAL_TCL_STATUS_RING_INFO0_CACHE_OP_RES GENMASK(6, 5)
+#define HAL_TCL_STATUS_RING_INFO0_MSDU_CNT GENMASK(31, 8)
+
+#define HAL_TCL_STATUS_RING_INFO1_HASH_IDX GENMASK(19, 0)
+
+#define HAL_TCL_STATUS_RING_INFO2_RING_ID GENMASK(27, 20)
+#define HAL_TCL_STATUS_RING_INFO2_LOOPING_COUNT GENMASK(31, 28)
+
+struct hal_tcl_status_ring {
+ u32 info0;
+ u32 msdu_byte_count;
+ u32 msdu_timestamp;
+ u32 meta_data[2];
+ u32 info1;
+ u32 rsvd0;
+ u32 info2;
+} __packed;
+
+/* hal_tcl_status_ring
+ *
+ * gse_ctrl
+ * GSE control operations. This includes cache operations and table
+ * entry statistics read/clear operation. Values are defined in
+ * enum %HAL_TCL_GSE_CTRL.
+ *
+ * gse_sel
+ * To select the ASE/FSE to do the operation mention by GSE_ctrl.
+ * 0: FSE select 1: ASE select
+ *
+ * cache_op_res
+ * Cache operation result. Values are defined in enum
+ * %HAL_TCL_CACHE_OP_RES_.
+ *
+ * msdu_cnt
+ * msdu_byte_count
+ * MSDU count of Entry and MSDU byte count for entry 1.
+ *
+ * hash_indx
+ * Hash value of the entry in case of search failed or disabled.
+ */
+
+#define HAL_CE_SRC_DESC_ADDR_INFO_ADDR_HI GENMASK(7, 0)
+#define HAL_CE_SRC_DESC_ADDR_INFO_HASH_EN BIT(8)
+#define HAL_CE_SRC_DESC_ADDR_INFO_BYTE_SWAP BIT(9)
+#define HAL_CE_SRC_DESC_ADDR_INFO_DEST_SWAP BIT(10)
+#define HAL_CE_SRC_DESC_ADDR_INFO_GATHER BIT(11)
+#define HAL_CE_SRC_DESC_ADDR_INFO_LEN GENMASK(31, 16)
+
+#define HAL_CE_SRC_DESC_META_INFO_DATA GENMASK(15, 0)
+
+#define HAL_CE_SRC_DESC_FLAGS_RING_ID GENMASK(27, 20)
+#define HAL_CE_SRC_DESC_FLAGS_LOOP_CNT HAL_SRNG_DESC_LOOP_CNT
+
+struct hal_ce_srng_src_desc {
+ u32 buffer_addr_low;
+ u32 buffer_addr_info; /* %HAL_CE_SRC_DESC_ADDR_INFO_ */
+ u32 meta_info; /* %HAL_CE_SRC_DESC_META_INFO_ */
+ u32 flags; /* %HAL_CE_SRC_DESC_FLAGS_ */
+} __packed;
+
+/*
+ * hal_ce_srng_src_desc
+ *
+ * buffer_addr_lo
+ * LSB 32 bits of the 40 Bit Pointer to the source buffer
+ *
+ * buffer_addr_hi
+ * MSB 8 bits of the 40 Bit Pointer to the source buffer
+ *
+ * toeplitz_en
+ * Enable generation of 32-bit Toeplitz-LFSR hash for
+ * data transfer. In case of gather field in first source
+ * ring entry of the gather copy cycle in taken into account.
+ *
+ * src_swap
+ * Treats source memory organization as big-endian. For
+ * each dword read (4 bytes), the byte 0 is swapped with byte 3
+ * and byte 1 is swapped with byte 2.
+ * In case of gather field in first source ring entry of
+ * the gather copy cycle in taken into account.
+ *
+ * dest_swap
+ * Treats destination memory organization as big-endian.
+ * For each dword write (4 bytes), the byte 0 is swapped with
+ * byte 3 and byte 1 is swapped with byte 2.
+ * In case of gather field in first source ring entry of
+ * the gather copy cycle in taken into account.
+ *
+ * gather
+ * Enables gather of multiple copy engine source
+ * descriptors to one destination.
+ *
+ * ce_res_0
+ * Reserved
+ *
+ *
+ * length
+ * Length of the buffer in units of octets of the current
+ * descriptor
+ *
+ * fw_metadata
+ * Meta data used by FW.
+ * In case of gather field in first source ring entry of
+ * the gather copy cycle in taken into account.
+ *
+ * ce_res_1
+ * Reserved
+ *
+ * ce_res_2
+ * Reserved
+ *
+ * ring_id
+ * The buffer pointer ring ID.
+ * 0 refers to the IDLE ring
+ * 1 - N refers to other rings
+ * Helps with debugging when dumping ring contents.
+ *
+ * looping_count
+ * A count value that indicates the number of times the
+ * producer of entries into the Ring has looped around the
+ * ring.
+ *
+ * At initialization time, this value is set to 0. On the
+ * first loop, this value is set to 1. After the max value is
+ * reached allowed by the number of bits for this field, the
+ * count value continues with 0 again.
+ *
+ * In case SW is the consumer of the ring entries, it can
+ * use this field to figure out up to where the producer of
+ * entries has created new entries. This eliminates the need to
+ * check where the head pointer' of the ring is located once
+ * the SW starts processing an interrupt indicating that new
+ * entries have been put into this ring...
+ *
+ * Also note that SW if it wants only needs to look at the
+ * LSB bit of this count value.
+ */
+
+#define HAL_CE_DEST_DESC_ADDR_INFO_ADDR_HI GENMASK(7, 0)
+#define HAL_CE_DEST_DESC_ADDR_INFO_RING_ID GENMASK(27, 20)
+#define HAL_CE_DEST_DESC_ADDR_INFO_LOOP_CNT HAL_SRNG_DESC_LOOP_CNT
+
+struct hal_ce_srng_dest_desc {
+ u32 buffer_addr_low;
+ u32 buffer_addr_info; /* %HAL_CE_DEST_DESC_ADDR_INFO_ */
+} __packed;
+
+/* hal_ce_srng_dest_desc
+ *
+ * dst_buffer_low
+ * LSB 32 bits of the 40 Bit Pointer to the Destination
+ * buffer
+ *
+ * dst_buffer_high
+ * MSB 8 bits of the 40 Bit Pointer to the Destination
+ * buffer
+ *
+ * ce_res_4
+ * Reserved
+ *
+ * ring_id
+ * The buffer pointer ring ID.
+ * 0 refers to the IDLE ring
+ * 1 - N refers to other rings
+ * Helps with debugging when dumping ring contents.
+ *
+ * looping_count
+ * A count value that indicates the number of times the
+ * producer of entries into the Ring has looped around the
+ * ring.
+ *
+ * At initialization time, this value is set to 0. On the
+ * first loop, this value is set to 1. After the max value is
+ * reached allowed by the number of bits for this field, the
+ * count value continues with 0 again.
+ *
+ * In case SW is the consumer of the ring entries, it can
+ * use this field to figure out up to where the producer of
+ * entries has created new entries. This eliminates the need to
+ * check where the head pointer' of the ring is located once
+ * the SW starts processing an interrupt indicating that new
+ * entries have been put into this ring...
+ *
+ * Also note that SW if it wants only needs to look at the
+ * LSB bit of this count value.
+ */
+
+#define HAL_CE_DST_STATUS_DESC_FLAGS_HASH_EN BIT(8)
+#define HAL_CE_DST_STATUS_DESC_FLAGS_BYTE_SWAP BIT(9)
+#define HAL_CE_DST_STATUS_DESC_FLAGS_DEST_SWAP BIT(10)
+#define HAL_CE_DST_STATUS_DESC_FLAGS_GATHER BIT(11)
+#define HAL_CE_DST_STATUS_DESC_FLAGS_LEN GENMASK(31, 16)
+
+#define HAL_CE_DST_STATUS_DESC_META_INFO_DATA GENMASK(7, 0)
+#define HAL_CE_DST_STATUS_DESC_META_INFO_RING_ID GENMASK(27, 20)
+#define HAL_CE_DST_STATUS_DESC_META_INFO_LOOP_CNT HAL_SRNG_DESC_LOOP_CNT
+
+struct hal_ce_srng_dst_status_desc {
+ u32 flags; /* %HAL_CE_DST_STATUS_DESC_FLAGS_ */
+ u32 toeplitz_hash0;
+ u32 toeplitz_hash1;
+ u32 meta_info; /* HAL_CE_DST_STATUS_DESC_META_INFO_ */
+} __packed;
+
+/* hal_ce_srng_dst_status_desc
+ *
+ * ce_res_5
+ * Reserved
+ *
+ * toeplitz_en
+ *
+ * src_swap
+ * Source memory buffer swapped
+ *
+ * dest_swap
+ * Destination memory buffer swapped
+ *
+ * gather
+ * Gather of multiple copy engine source descriptors to one
+ * destination enabled
+ *
+ * ce_res_6
+ * Reserved
+ *
+ * length
+ * Sum of all the Lengths of the source descriptor in the
+ * gather chain
+ *
+ * toeplitz_hash_0
+ * 32 LS bits of 64 bit Toeplitz LFSR hash result
+ *
+ * toeplitz_hash_1
+ * 32 MS bits of 64 bit Toeplitz LFSR hash result
+ *
+ * fw_metadata
+ * Meta data used by FW
+ * In case of gather field in first source ring entry of
+ * the gather copy cycle in taken into account.
+ *
+ * ce_res_7
+ * Reserved
+ *
+ * ring_id
+ * The buffer pointer ring ID.
+ * 0 refers to the IDLE ring
+ * 1 - N refers to other rings
+ * Helps with debugging when dumping ring contents.
+ *
+ * looping_count
+ * A count value that indicates the number of times the
+ * producer of entries into the Ring has looped around the
+ * ring.
+ *
+ * At initialization time, this value is set to 0. On the
+ * first loop, this value is set to 1. After the max value is
+ * reached allowed by the number of bits for this field, the
+ * count value continues with 0 again.
+ *
+ * In case SW is the consumer of the ring entries, it can
+ * use this field to figure out up to where the producer of
+ * entries has created new entries. This eliminates the need to
+ * check where the head pointer' of the ring is located once
+ * the SW starts processing an interrupt indicating that new
+ * entries have been put into this ring...
+ *
+ * Also note that SW if it wants only needs to look at the
+ * LSB bit of this count value.
+ */
+
+#define HAL_TX_RATE_STATS_INFO0_VALID BIT(0)
+#define HAL_TX_RATE_STATS_INFO0_BW GENMASK(2, 1)
+#define HAL_TX_RATE_STATS_INFO0_PKT_TYPE GENMASK(6, 3)
+#define HAL_TX_RATE_STATS_INFO0_STBC BIT(7)
+#define HAL_TX_RATE_STATS_INFO0_LDPC BIT(8)
+#define HAL_TX_RATE_STATS_INFO0_SGI GENMASK(10, 9)
+#define HAL_TX_RATE_STATS_INFO0_MCS GENMASK(14, 11)
+#define HAL_TX_RATE_STATS_INFO0_OFDMA_TX BIT(15)
+#define HAL_TX_RATE_STATS_INFO0_TONES_IN_RU GENMASK(27, 16)
+
+enum hal_tx_rate_stats_bw {
+ HAL_TX_RATE_STATS_BW_20,
+ HAL_TX_RATE_STATS_BW_40,
+ HAL_TX_RATE_STATS_BW_80,
+ HAL_TX_RATE_STATS_BW_160,
+};
+
+enum hal_tx_rate_stats_pkt_type {
+ HAL_TX_RATE_STATS_PKT_TYPE_11A,
+ HAL_TX_RATE_STATS_PKT_TYPE_11B,
+ HAL_TX_RATE_STATS_PKT_TYPE_11N,
+ HAL_TX_RATE_STATS_PKT_TYPE_11AC,
+ HAL_TX_RATE_STATS_PKT_TYPE_11AX,
+};
+
+enum hal_tx_rate_stats_sgi {
+ HAL_TX_RATE_STATS_SGI_08US,
+ HAL_TX_RATE_STATS_SGI_04US,
+ HAL_TX_RATE_STATS_SGI_16US,
+ HAL_TX_RATE_STATS_SGI_32US,
+};
+
+struct hal_tx_rate_stats {
+ u32 info0;
+ u32 tsf;
+} __packed;
+
+struct hal_wbm_link_desc {
+ struct ath11k_buffer_addr buf_addr_info;
+} __packed;
+
+/* hal_wbm_link_desc
+ *
+ * Producer: WBM
+ * Consumer: WBM
+ *
+ * buf_addr_info
+ * Details of the physical address of a buffer or MSDU
+ * link descriptor.
+ */
+
+enum hal_wbm_rel_src_module {
+ HAL_WBM_REL_SRC_MODULE_TQM,
+ HAL_WBM_REL_SRC_MODULE_RXDMA,
+ HAL_WBM_REL_SRC_MODULE_REO,
+ HAL_WBM_REL_SRC_MODULE_FW,
+ HAL_WBM_REL_SRC_MODULE_SW,
+};
+
+enum hal_wbm_rel_desc_type {
+ HAL_WBM_REL_DESC_TYPE_REL_MSDU,
+ HAL_WBM_REL_DESC_TYPE_MSDU_LINK,
+ HAL_WBM_REL_DESC_TYPE_MPDU_LINK,
+ HAL_WBM_REL_DESC_TYPE_MSDU_EXT,
+ HAL_WBM_REL_DESC_TYPE_QUEUE_EXT,
+};
+
+/* hal_wbm_rel_desc_type
+ *
+ * msdu_buffer
+ * The address points to an MSDU buffer
+ *
+ * msdu_link_descriptor
+ * The address points to an Tx MSDU link descriptor
+ *
+ * mpdu_link_descriptor
+ * The address points to an MPDU link descriptor
+ *
+ * msdu_ext_descriptor
+ * The address points to an MSDU extension descriptor
+ *
+ * queue_ext_descriptor
+ * The address points to an TQM queue extension descriptor. WBM should
+ * treat this is the same way as a link descriptor.
+ */
+
+enum hal_wbm_rel_bm_act {
+ HAL_WBM_REL_BM_ACT_PUT_IN_IDLE,
+ HAL_WBM_REL_BM_ACT_REL_MSDU,
+};
+
+/* hal_wbm_rel_bm_act
+ *
+ * put_in_idle_list
+ * Put the buffer or descriptor back in the idle list. In case of MSDU or
+ * MDPU link descriptor, BM does not need to check to release any
+ * individual MSDU buffers.
+ *
+ * release_msdu_list
+ * This BM action can only be used in combination with desc_type being
+ * msdu_link_descriptor. Field first_msdu_index points out which MSDU
+ * pointer in the MSDU link descriptor is the first of an MPDU that is
+ * released. BM shall release all the MSDU buffers linked to this first
+ * MSDU buffer pointer. All related MSDU buffer pointer entries shall be
+ * set to value 0, which represents the 'NULL' pointer. When all MSDU
+ * buffer pointers in the MSDU link descriptor are 'NULL', the MSDU link
+ * descriptor itself shall also be released.
+ */
+
+#define HAL_WBM_RELEASE_INFO0_REL_SRC_MODULE GENMASK(2, 0)
+#define HAL_WBM_RELEASE_INFO0_BM_ACTION GENMASK(5, 3)
+#define HAL_WBM_RELEASE_INFO0_DESC_TYPE GENMASK(8, 6)
+#define HAL_WBM_RELEASE_INFO0_FIRST_MSDU_IDX GENMASK(12, 9)
+#define HAL_WBM_RELEASE_INFO0_TQM_RELEASE_REASON GENMASK(16, 13)
+#define HAL_WBM_RELEASE_INFO0_RXDMA_PUSH_REASON GENMASK(18, 17)
+#define HAL_WBM_RELEASE_INFO0_RXDMA_ERROR_CODE GENMASK(23, 19)
+#define HAL_WBM_RELEASE_INFO0_REO_PUSH_REASON GENMASK(25, 24)
+#define HAL_WBM_RELEASE_INFO0_REO_ERROR_CODE GENMASK(30, 26)
+#define HAL_WBM_RELEASE_INFO0_WBM_INTERNAL_ERROR BIT(31)
+
+#define HAL_WBM_RELEASE_INFO1_TQM_STATUS_NUMBER GENMASK(23, 0)
+#define HAL_WBM_RELEASE_INFO1_TRANSMIT_COUNT GENMASK(30, 24)
+
+#define HAL_WBM_RELEASE_INFO2_ACK_FRAME_RSSI GENMASK(7, 0)
+#define HAL_WBM_RELEASE_INFO2_SW_REL_DETAILS_VALID BIT(8)
+#define HAL_WBM_RELEASE_INFO2_FIRST_MSDU BIT(9)
+#define HAL_WBM_RELEASE_INFO2_LAST_MSDU BIT(10)
+#define HAL_WBM_RELEASE_INFO2_MSDU_IN_AMSDU BIT(11)
+#define HAL_WBM_RELEASE_INFO2_FW_TX_NOTIF_FRAME BIT(12)
+#define HAL_WBM_RELEASE_INFO2_BUFFER_TIMESTAMP GENMASK(31, 13)
+
+#define HAL_WBM_RELEASE_INFO3_PEER_ID GENMASK(15, 0)
+#define HAL_WBM_RELEASE_INFO3_TID GENMASK(19, 16)
+#define HAL_WBM_RELEASE_INFO3_RING_ID GENMASK(27, 20)
+#define HAL_WBM_RELEASE_INFO3_LOOPING_COUNT GENMASK(31, 28)
+
+#define HAL_WBM_REL_HTT_TX_COMP_INFO0_STATUS GENMASK(12, 9)
+#define HAL_WBM_REL_HTT_TX_COMP_INFO0_REINJ_REASON GENMASK(16, 13)
+#define HAL_WBM_REL_HTT_TX_COMP_INFO0_EXP_FRAME BIT(17)
+
+struct hal_wbm_release_ring {
+ struct ath11k_buffer_addr buf_addr_info;
+ u32 info0;
+ u32 info1;
+ u32 info2;
+ struct hal_tx_rate_stats rate_stats;
+ u32 info3;
+} __packed;
+
+/* hal_wbm_release_ring
+ *
+ * Producer: SW/TQM/RXDMA/REO/SWITCH
+ * Consumer: WBM/SW/FW
+ *
+ * HTT tx status is overlayed on wbm_release ring on 4-byte words 2, 3, 4 and 5
+ * for software based completions.
+ *
+ * buf_addr_info
+ * Details of the physical address of the buffer or link descriptor.
+ *
+ * release_source_module
+ * Indicates which module initiated the release of this buffer/descriptor.
+ * Values are defined in enum %HAL_WBM_REL_SRC_MODULE_.
+ *
+ * bm_action
+ * Field only valid when the field return_buffer_manager in
+ * Released_buff_or_desc_addr_info indicates:
+ * WBM_IDLE_BUF_LIST / WBM_IDLE_DESC_LIST
+ * Values are defined in enum %HAL_WBM_REL_BM_ACT_.
+ *
+ * buffer_or_desc_type
+ * Field only valid when WBM is marked as the return_buffer_manager in
+ * the Released_Buffer_address_info. Indicates that type of buffer or
+ * descriptor is being released. Values are in enum %HAL_WBM_REL_DESC_TYPE.
+ *
+ * first_msdu_index
+ * Field only valid for the bm_action release_msdu_list. The index of the
+ * first MSDU in an MSDU link descriptor all belonging to the same MPDU.
+ *
+ * tqm_release_reason
+ * Field only valid when Release_source_module is set to release_source_TQM
+ * Release reasons are defined in enum %HAL_WBM_TQM_REL_REASON_.
+ *
+ * rxdma_push_reason
+ * reo_push_reason
+ * Indicates why rxdma/reo pushed the frame to this ring and values are
+ * defined in enum %HAL_REO_DEST_RING_PUSH_REASON_.
+ *
+ * rxdma_error_code
+ * Field only valid when 'rxdma_push_reason' set to 'error_detected'.
+ * Values are defined in enum %HAL_REO_ENTR_RING_RXDMA_ECODE_.
+ *
+ * reo_error_code
+ * Field only valid when 'reo_push_reason' set to 'error_detected'. Values
+ * are defined in enum %HAL_REO_DEST_RING_ERROR_CODE_.
+ *
+ * wbm_internal_error
+ * Is set when WBM got a buffer pointer but the action was to push it to
+ * the idle link descriptor ring or do link related activity OR
+ * Is set when WBM got a link buffer pointer but the action was to push it
+ * to the buffer descriptor ring.
+ *
+ * tqm_status_number
+ * The value in this field is equal to tqm_cmd_number in TQM command. It is
+ * used to correlate the statu with TQM commands. Only valid when
+ * release_source_module is TQM.
+ *
+ * transmit_count
+ * The number of times the frame has been transmitted, valid only when
+ * release source in TQM.
+ *
+ * ack_frame_rssi
+ * This field is only valid when the source is TQM. If this frame is
+ * removed as the result of the reception of an ACK or BA, this field
+ * indicates the RSSI of the received ACK or BA frame.
+ *
+ * sw_release_details_valid
+ * This is set when WMB got a 'release_msdu_list' command from TQM and
+ * return buffer manager is not WMB. WBM will then de-aggregate all MSDUs
+ * and pass them one at a time on to the 'buffer owner'.
+ *
+ * first_msdu
+ * Field only valid when SW_release_details_valid is set.
+ * When set, this MSDU is the first MSDU pointed to in the
+ * 'release_msdu_list' command.
+ *
+ * last_msdu
+ * Field only valid when SW_release_details_valid is set.
+ * When set, this MSDU is the last MSDU pointed to in the
+ * 'release_msdu_list' command.
+ *
+ * msdu_part_of_amsdu
+ * Field only valid when SW_release_details_valid is set.
+ * When set, this MSDU was part of an A-MSDU in MPDU
+ *
+ * fw_tx_notify_frame
+ * Field only valid when SW_release_details_valid is set.
+ *
+ * buffer_timestamp
+ * Field only valid when SW_release_details_valid is set.
+ * This is the Buffer_timestamp field from the
+ * Timestamp in units of 1024 us
+ *
+ * struct hal_tx_rate_stats rate_stats
+ * Details for command execution tracking purposes.
+ *
+ * sw_peer_id
+ * tid
+ * Field only valid when Release_source_module is set to
+ * release_source_TQM
+ *
+ * 1) Release of msdu buffer due to drop_frame = 1. Flow is
+ * not fetched and hence sw_peer_id and tid = 0
+ *
+ * buffer_or_desc_type = e_num 0
+ * MSDU_rel_buffertqm_release_reason = e_num 1
+ * tqm_rr_rem_cmd_rem
+ *
+ * 2) Release of msdu buffer due to Flow is not fetched and
+ * hence sw_peer_id and tid = 0
+ *
+ * buffer_or_desc_type = e_num 0
+ * MSDU_rel_buffertqm_release_reason = e_num 1
+ * tqm_rr_rem_cmd_rem
+ *
+ * 3) Release of msdu link due to remove_mpdu or acked_mpdu
+ * command.
+ *
+ * buffer_or_desc_type = e_num1
+ * msdu_link_descriptortqm_release_reason can be:e_num 1
+ * tqm_rr_rem_cmd_reme_num 2 tqm_rr_rem_cmd_tx
+ * e_num 3 tqm_rr_rem_cmd_notxe_num 4 tqm_rr_rem_cmd_aged
+ *
+ * This field represents the TID from the TX_MSDU_FLOW
+ * descriptor or TX_MPDU_QUEUE descriptor
+ *
+ * rind_id
+ * For debugging.
+ * This field is filled in by the SRNG module.
+ * It help to identify the ring that is being looked
+ *
+ * looping_count
+ * A count value that indicates the number of times the
+ * producer of entries into the Buffer Manager Ring has looped
+ * around the ring.
+ *
+ * At initialization time, this value is set to 0. On the
+ * first loop, this value is set to 1. After the max value is
+ * reached allowed by the number of bits for this field, the
+ * count value continues with 0 again.
+ *
+ * In case SW is the consumer of the ring entries, it can
+ * use this field to figure out up to where the producer of
+ * entries has created new entries. This eliminates the need to
+ * check where the head pointer' of the ring is located once
+ * the SW starts processing an interrupt indicating that new
+ * entries have been put into this ring...
+ *
+ * Also note that SW if it wants only needs to look at the
+ * LSB bit of this count value.
+ */
+
+/**
+ * enum hal_wbm_tqm_rel_reason - TQM release reason code
+ * @HAL_WBM_TQM_REL_REASON_FRAME_ACKED: ACK or BACK received for the frame
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_MPDU: Command remove_mpdus initiated by SW
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_TX: Command remove transmitted_mpdus
+ * initiated by sw.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_NOTX: Command remove untransmitted_mpdus
+ * initiated by sw.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_AGED_FRAMES: Command remove aged msdus or
+ * mpdus.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON1: Remove command initiated by
+ * fw with fw_reason1.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON2: Remove command initiated by
+ * fw with fw_reason2.
+ * @HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON3: Remove command initiated by
+ * fw with fw_reason3.
+ */
+enum hal_wbm_tqm_rel_reason {
+ HAL_WBM_TQM_REL_REASON_FRAME_ACKED,
+ HAL_WBM_TQM_REL_REASON_CMD_REMOVE_MPDU,
+ HAL_WBM_TQM_REL_REASON_CMD_REMOVE_TX,
+ HAL_WBM_TQM_REL_REASON_CMD_REMOVE_NOTX,
+ HAL_WBM_TQM_REL_REASON_CMD_REMOVE_AGED_FRAMES,
+ HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON1,
+ HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON2,
+ HAL_WBM_TQM_REL_REASON_CMD_REMOVE_RESEAON3,
+};
+
+struct hal_wbm_buffer_ring {
+ struct ath11k_buffer_addr buf_addr_info;
+};
+
+enum hal_desc_owner {
+ HAL_DESC_OWNER_WBM,
+ HAL_DESC_OWNER_SW,
+ HAL_DESC_OWNER_TQM,
+ HAL_DESC_OWNER_RXDMA,
+ HAL_DESC_OWNER_REO,
+ HAL_DESC_OWNER_SWITCH,
+};
+
+enum hal_desc_buf_type {
+ HAL_DESC_BUF_TYPE_TX_MSDU_LINK,
+ HAL_DESC_BUF_TYPE_TX_MPDU_LINK,
+ HAL_DESC_BUF_TYPE_TX_MPDU_QUEUE_HEAD,
+ HAL_DESC_BUF_TYPE_TX_MPDU_QUEUE_EXT,
+ HAL_DESC_BUF_TYPE_TX_FLOW,
+ HAL_DESC_BUF_TYPE_TX_BUFFER,
+ HAL_DESC_BUF_TYPE_RX_MSDU_LINK,
+ HAL_DESC_BUF_TYPE_RX_MPDU_LINK,
+ HAL_DESC_BUF_TYPE_RX_REO_QUEUE,
+ HAL_DESC_BUF_TYPE_RX_REO_QUEUE_EXT,
+ HAL_DESC_BUF_TYPE_RX_BUFFER,
+ HAL_DESC_BUF_TYPE_IDLE_LINK,
+};
+
+#define HAL_DESC_REO_OWNED 4
+#define HAL_DESC_REO_QUEUE_DESC 8
+#define HAL_DESC_REO_QUEUE_EXT_DESC 9
+#define HAL_DESC_REO_NON_QOS_TID 16
+
+#define HAL_DESC_HDR_INFO0_OWNER GENMASK(3, 0)
+#define HAL_DESC_HDR_INFO0_BUF_TYPE GENMASK(7, 4)
+#define HAL_DESC_HDR_INFO0_DBG_RESERVED GENMASK(31, 8)
+
+struct hal_desc_header {
+ u32 info0;
+} __packed;
+
+struct hal_rx_mpdu_link_ptr {
+ struct ath11k_buffer_addr addr_info;
+} __packed;
+
+struct hal_rx_msdu_details {
+ struct ath11k_buffer_addr buf_addr_info;
+ struct rx_msdu_desc rx_msdu_info;
+} __packed;
+
+#define HAL_RX_MSDU_LNK_INFO0_RX_QUEUE_NUMBER GENMASK(15, 0)
+#define HAL_RX_MSDU_LNK_INFO0_FIRST_MSDU_LNK BIT(16)
+
+struct hal_rx_msdu_link {
+ struct hal_desc_header desc_hdr;
+ struct ath11k_buffer_addr buf_addr_info;
+ u32 info0;
+ u32 pn[4];
+ struct hal_rx_msdu_details msdu_link[6];
+} __packed;
+
+struct hal_rx_reo_queue_ext {
+ struct hal_desc_header desc_hdr;
+ u32 rsvd;
+ struct hal_rx_mpdu_link_ptr mpdu_link[15];
+} __packed;
+
+/* hal_rx_reo_queue_ext
+ * Consumer: REO
+ * Producer: REO
+ *
+ * descriptor_header
+ * Details about which module owns this struct.
+ *
+ * mpdu_link
+ * Pointer to the next MPDU_link descriptor in the MPDU queue.
+ */
+
+enum hal_rx_reo_queue_pn_size {
+ HAL_RX_REO_QUEUE_PN_SIZE_24,
+ HAL_RX_REO_QUEUE_PN_SIZE_48,
+ HAL_RX_REO_QUEUE_PN_SIZE_128,
+};
+
+#define HAL_RX_REO_QUEUE_RX_QUEUE_NUMBER GENMASK(15, 0)
+
+#define HAL_RX_REO_QUEUE_INFO0_VLD BIT(0)
+#define HAL_RX_REO_QUEUE_INFO0_ASSOC_LNK_DESC_COUNTER GENMASK(2, 1)
+#define HAL_RX_REO_QUEUE_INFO0_DIS_DUP_DETECTION BIT(3)
+#define HAL_RX_REO_QUEUE_INFO0_SOFT_REORDER_EN BIT(4)
+#define HAL_RX_REO_QUEUE_INFO0_AC GENMASK(6, 5)
+#define HAL_RX_REO_QUEUE_INFO0_BAR BIT(7)
+#define HAL_RX_REO_QUEUE_INFO0_RETRY BIT(8)
+#define HAL_RX_REO_QUEUE_INFO0_CHECK_2K_MODE BIT(9)
+#define HAL_RX_REO_QUEUE_INFO0_OOR_MODE BIT(10)
+#define HAL_RX_REO_QUEUE_INFO0_BA_WINDOW_SIZE GENMASK(18, 11)
+#define HAL_RX_REO_QUEUE_INFO0_PN_CHECK BIT(19)
+#define HAL_RX_REO_QUEUE_INFO0_EVEN_PN BIT(20)
+#define HAL_RX_REO_QUEUE_INFO0_UNEVEN_PN BIT(21)
+#define HAL_RX_REO_QUEUE_INFO0_PN_HANDLE_ENABLE BIT(22)
+#define HAL_RX_REO_QUEUE_INFO0_PN_SIZE GENMASK(24, 23)
+#define HAL_RX_REO_QUEUE_INFO0_IGNORE_AMPDU_FLG BIT(25)
+
+#define HAL_RX_REO_QUEUE_INFO1_SVLD BIT(0)
+#define HAL_RX_REO_QUEUE_INFO1_SSN GENMASK(12, 1)
+#define HAL_RX_REO_QUEUE_INFO1_CURRENT_IDX GENMASK(20, 13)
+#define HAL_RX_REO_QUEUE_INFO1_SEQ_2K_ERR BIT(21)
+#define HAL_RX_REO_QUEUE_INFO1_PN_ERR BIT(22)
+#define HAL_RX_REO_QUEUE_INFO1_PN_VALID BIT(31)
+
+#define HAL_RX_REO_QUEUE_INFO2_MPDU_COUNT GENMASK(6, 0)
+#define HAL_RX_REO_QUEUE_INFO2_MSDU_COUNT (31, 7)
+
+#define HAL_RX_REO_QUEUE_INFO3_TIMEOUT_COUNT GENMASK(9, 4)
+#define HAL_RX_REO_QUEUE_INFO3_FWD_DUE_TO_BAR_CNT GENMASK(15, 10)
+#define HAL_RX_REO_QUEUE_INFO3_DUPLICATE_COUNT GENMASK(31, 10)
+
+#define HAL_RX_REO_QUEUE_INFO4_FRAME_IN_ORD_COUNT GENMASK(23, 0)
+#define HAL_RX_REO_QUEUE_INFO4_BAR_RECVD_COUNT GENMASK(31, 24)
+
+#define HAL_RX_REO_QUEUE_INFO5_LATE_RX_MPDU_COUNT GENMASK(11, 0)
+#define HAL_RX_REO_QUEUE_INFO5_WINDOW_JUMP_2K GENMASK(15, 12)
+#define HAL_RX_REO_QUEUE_INFO5_HOLE_COUNT GENMASK(31, 16)
+
+struct hal_rx_reo_queue {
+ struct hal_desc_header desc_hdr;
+ u32 rx_queue_num;
+ u32 info0;
+ u32 info1;
+ u32 pn[4];
+ u32 last_rx_enqueue_timestamp;
+ u32 last_rx_dequeue_timestamp;
+ u32 next_aging_queue[2];
+ u32 prev_aging_queue[2];
+ u32 rx_bitmap[8];
+ u32 info2;
+ u32 info3;
+ u32 info4;
+ u32 processed_mpdus;
+ u32 processed_msdus;
+ u32 processed_total_bytes;
+ u32 info5;
+ u32 rsvd[3];
+ struct hal_rx_reo_queue_ext ext_desc[0];
+} __packed;
+
+/* hal_rx_reo_queue
+ *
+ * descriptor_header
+ * Details about which module owns this struct. Note that sub field
+ * Buffer_type shall be set to receive_reo_queue_descriptor.
+ *
+ * receive_queue_number
+ * Indicates the MPDU queue ID to which this MPDU link descriptor belongs.
+ *
+ * vld
+ * Valid bit indicating a session is established and the queue descriptor
+ * is valid.
+ * associated_link_descriptor_counter
+ * Indicates which of the 3 link descriptor counters shall be incremented
+ * or decremented when link descriptors are added or removed from this
+ * flow queue.
+ * disable_duplicate_detection
+ * When set, do not perform any duplicate detection.
+ * soft_reorder_enable
+ * When set, REO has been instructed to not perform the actual re-ordering
+ * of frames for this queue, but just to insert the reorder opcodes.
+ * ac
+ * Indicates the access category of the queue descriptor.
+ * bar
+ * Indicates if BAR has been received.
+ * retry
+ * Retry bit is checked if this bit is set.
+ * chk_2k_mode
+ * Indicates what type of operation is expected from Reo when the received
+ * frame SN falls within the 2K window.
+ * oor_mode
+ * Indicates what type of operation is expected when the received frame
+ * falls within the OOR window.
+ * ba_window_size
+ * Indicates the negotiated (window size + 1). Max of 256 bits.
+ *
+ * A value 255 means 256 bitmap, 63 means 64 bitmap, 0 (means non-BA
+ * session, with window size of 0). The 3 values here are the main values
+ * validated, but other values should work as well.
+ *
+ * A BA window size of 0 (=> one frame entry bitmat), means that there is
+ * no additional rx_reo_queue_ext desc. following rx_reo_queue in memory.
+ * A BA window size of 1 - 105, means that there is 1 rx_reo_queue_ext.
+ * A BA window size of 106 - 210, means that there are 2 rx_reo_queue_ext.
+ * A BA window size of 211 - 256, means that there are 3 rx_reo_queue_ext.
+ * pn_check_needed, pn_shall_be_even, pn_shall_be_uneven, pn_handling_enable,
+ * pn_size
+ * REO shall perform the PN increment check, even number check, uneven
+ * number check, PN error check and size of the PN field check.
+ * ignore_ampdu_flag
+ * REO shall ignore the ampdu_flag on entrance descriptor for this queue.
+ *
+ * svld
+ * Sequence number in next field is valid one.
+ * ssn
+ * Starting Sequence number of the session.
+ * current_index
+ * Points to last forwarded packet
+ * seq_2k_error_detected_flag
+ * REO has detected a 2k error jump in the sequence number and from that
+ * moment forward, all new frames are forwarded directly to FW, without
+ * duplicate detect, reordering, etc.
+ * pn_error_detected_flag
+ * REO has detected a PN error.
+ */
+
+#define HAL_REO_UPD_RX_QUEUE_INFO0_QUEUE_ADDR_HI GENMASK(7, 0)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_RX_QUEUE_NUM BIT(8)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_VLD BIT(9)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_ASSOC_LNK_DESC_CNT BIT(10)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_DIS_DUP_DETECTION BIT(11)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_SOFT_REORDER_EN BIT(12)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_AC BIT(13)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_BAR BIT(14)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_RETRY BIT(15)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_CHECK_2K_MODE BIT(16)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_OOR_MODE BIT(17)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_BA_WINDOW_SIZE BIT(18)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_CHECK BIT(19)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_EVEN_PN BIT(20)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_UNEVEN_PN BIT(21)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_HANDLE_ENABLE BIT(22)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_SIZE BIT(23)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_IGNORE_AMPDU_FLG BIT(24)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_SVLD BIT(25)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_SSN BIT(26)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_SEQ_2K_ERR BIT(27)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_ERR BIT(28)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN_VALID BIT(29)
+#define HAL_REO_UPD_RX_QUEUE_INFO0_UPD_PN BIT(30)
+
+#define HAL_REO_UPD_RX_QUEUE_INFO1_RX_QUEUE_NUMBER GENMASK(15, 0)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_VLD BIT(16)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_ASSOC_LNK_DESC_COUNTER GENMASK(18, 17)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_DIS_DUP_DETECTION BIT(19)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_SOFT_REORDER_EN BIT(20)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_AC GENMASK(22, 21)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_BAR BIT(23)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_RETRY BIT(24)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_CHECK_2K_MODE BIT(25)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_OOR_MODE BIT(26)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_PN_CHECK BIT(27)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_EVEN_PN BIT(28)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_UNEVEN_PN BIT(29)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_PN_HANDLE_ENABLE BIT(30)
+#define HAL_REO_UPD_RX_QUEUE_INFO1_IGNORE_AMPDU_FLG BIT(31)
+
+#define HAL_REO_UPD_RX_QUEUE_INFO2_BA_WINDOW_SIZE GENMASK(7, 0)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_PN_SIZE GENMASK(9, 8)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_SVLD BIT(10)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_SSN GENMASK(22, 11)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_SEQ_2K_ERR BIT(23)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_PN_ERR BIT(24)
+#define HAL_REO_UPD_RX_QUEUE_INFO2_PN_VALID BIT(25)
+
+struct hal_reo_update_rx_queue {
+ struct hal_reo_cmd_hdr cmd;
+ u32 queue_addr_lo;
+ u32 info0;
+ u32 info1;
+ u32 info2;
+ u32 pn[4];
+} __packed;
+
+#define HAL_REO_UNBLOCK_CACHE_INFO0_UNBLK_CACHE BIT(0)
+#define HAL_REO_UNBLOCK_CACHE_INFO0_RESOURCE_IDX GENMASK(2, 1)
+
+struct hal_reo_unblock_cache {
+ struct hal_reo_cmd_hdr cmd;
+ u32 info0;
+ u32 rsvd[7];
+} __packed;
+
+enum hal_reo_exec_status {
+ HAL_REO_EXEC_STATUS_SUCCESS,
+ HAL_REO_EXEC_STATUS_BLOCKED,
+ HAL_REO_EXEC_STATUS_FAILED,
+ HAL_REO_EXEC_STATUS_RESOURCE_BLOCKED,
+};
+
+#define HAL_REO_STATUS_HDR_INFO0_STATUS_NUM GENMASK(15, 0)
+#define HAL_REO_STATUS_HDR_INFO0_EXEC_TIME GENMASK(25, 16)
+#define HAL_REO_STATUS_HDR_INFO0_EXEC_STATUS GENMASK(27, 26)
+
+struct hal_reo_status_hdr {
+ u32 info0;
+ u32 timestamp;
+} __packed;
+
+/* hal_reo_status_hdr
+ * Producer: REO
+ * Consumer: SW
+ *
+ * status_num
+ * The value in this field is equal to value of the reo command
+ * number. This field helps to correlate the statuses with the REO
+ * commands.
+ *
+ * execution_time (in us)
+ * The amount of time REO took to excecute the command. Note that
+ * this time does not include the duration of the command waiting
+ * in the command ring, before the execution started.
+ *
+ * execution_status
+ * Execution status of the command. Values are defined in
+ * enum %HAL_REO_EXEC_STATUS_.
+ */
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO0_SSN GENMASK(11, 0)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO0_CUR_IDX GENMASK(19, 12)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO1_MPDU_COUNT GENMASK(6, 0)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO1_MSDU_COUNT GENMASK(31, 7)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO2_TIMEOUT_COUNT GENMASK(9, 4)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO2_FDTB_COUNT GENMASK(15, 10)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO2_DUPLICATE_COUNT GENMASK(31, 16)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO3_FIO_COUNT GENMASK(23, 0)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO3_BAR_RCVD_CNT GENMASK(31, 24)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO4_LATE_RX_MPDU GENMASK(11, 0)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO4_WINDOW_JMP2K GENMASK(15, 12)
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO4_HOLE_COUNT GENMASK(31, 16)
+
+#define HAL_REO_GET_QUEUE_STATS_STATUS_INFO5_LOOPING_CNT GENMASK(31, 28)
+
+struct hal_reo_get_queue_stats_status {
+ struct hal_reo_status_hdr hdr;
+ u32 info0;
+ u32 pn[4];
+ u32 last_rx_enqueue_timestamp;
+ u32 last_rx_dequeue_timestamp;
+ u32 rx_bitmap[8];
+ u32 info1;
+ u32 info2;
+ u32 info3;
+ u32 num_mpdu_frames;
+ u32 num_msdu_frames;
+ u32 total_bytes;
+ u32 info4;
+ u32 info5;
+} __packed;
+
+/* hal_reo_get_queue_stats_status
+ * Producer: REO
+ * Consumer: SW
+ *
+ * status_hdr
+ * Details that can link this status with the original command. It
+ * also contains info on how long REO took to execute this command.
+ *
+ * ssn
+ * Starting Sequence number of the session, this changes whenever
+ * window moves (can be filled by SW then maintained by REO).
+ *
+ * current_index
+ * Points to last forwarded packet.
+ *
+ * pn
+ * Bits of the PN number.
+ *
+ * last_rx_enqueue_timestamp
+ * last_rx_dequeue_timestamp
+ * Timestamp of arrival of the last MPDU for this queue and
+ * Timestamp of forwarding an MPDU accordingly.
+ *
+ * rx_bitmap
+ * When a bit is set, the corresponding frame is currently held
+ * in the re-order queue. The bitmap is Fully managed by HW.
+ *
+ * current_mpdu_count
+ * current_msdu_count
+ * The number of MPDUs and MSDUs in the queue.
+ *
+ * timeout_count
+ * The number of times REO started forwarding frames even though
+ * there is a hole in the bitmap. Forwarding reason is timeout.
+ *
+ * forward_due_to_bar_count
+ * The number of times REO started forwarding frames even though
+ * there is a hole in the bitmap. Fwd reason is reception of BAR.
+ *
+ * duplicate_count
+ * The number of duplicate frames that have been detected.
+ *
+ * frames_in_order_count
+ * The number of frames that have been received in order (without
+ * a hole that prevented them from being forwarded immediately).
+ *
+ * bar_received_count
+ * The number of times a BAR frame is received.
+ *
+ * mpdu_frames_processed_count
+ * msdu_frames_processed_count
+ * The total number of MPDU/MSDU frames that have been processed.
+ *
+ * total_bytes
+ * An approximation of the number of bytes received for this queue.
+ *
+ * late_receive_mpdu_count
+ * The number of MPDUs received after the window had already moved
+ * on. The 'late' sequence window is defined as
+ * (Window SSN - 256) - (Window SSN - 1).
+ *
+ * window_jump_2k
+ * The number of times the window moved more than 2K
+ *
+ * hole_count
+ * The number of times a hole was created in the receive bitmap.
+ *
+ * looping_count
+ * A count value that indicates the number of times the producer of
+ * entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_STATUS_LOOP_CNT GENMASK(31, 28)
+
+#define HAL_REO_FLUSH_QUEUE_INFO0_ERR_DETECTED BIT(0)
+#define HAL_REO_FLUSH_QUEUE_INFO0_RSVD GENMASK(31, 1)
+#define HAL_REO_FLUSH_QUEUE_INFO1_RSVD GENMASK(27, 0)
+
+struct hal_reo_flush_queue_status {
+ struct hal_reo_status_hdr hdr;
+ u32 info0;
+ u32 rsvd0[21];
+ u32 info1;
+} __packed;
+
+/* hal_reo_flush_queue_status
+ * Producer: REO
+ * Consumer: SW
+ *
+ * status_hdr
+ * Details that can link this status with the original command. It
+ * also contains info on how long REO took to execute this command.
+ *
+ * error_detected
+ * Status of blocking resource
+ *
+ * 0 - No error has been detected while executing this command
+ * 1 - Error detected. The resource to be used for blocking was
+ * already in use.
+ *
+ * looping_count
+ * A count value that indicates the number of times the producer of
+ * entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_IS_ERR BIT(0)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_BLOCK_ERR_CODE GENMASK(2, 1)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_STATUS_HIT BIT(8)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_DESC_TYPE GENMASK(11, 9)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_CLIENT_ID GENMASK(15, 12)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_ERR GENMASK(17, 16)
+#define HAL_REO_FLUSH_CACHE_STATUS_INFO0_FLUSH_COUNT GENMASK(25, 18)
+
+struct hal_reo_flush_cache_status {
+ struct hal_reo_status_hdr hdr;
+ u32 info0;
+ u32 rsvd0[21];
+ u32 info1;
+} __packed;
+
+/* hal_reo_flush_cache_status
+ * Producer: REO
+ * Consumer: SW
+ *
+ * status_hdr
+ * Details that can link this status with the original command. It
+ * also contains info on how long REO took to execute this command.
+ *
+ * error_detected
+ * Status for blocking resource handling
+ *
+ * 0 - No error has been detected while executing this command
+ * 1 - An error in the blocking resource management was detected
+ *
+ * block_error_details
+ * only valid when error_detected is set
+ *
+ * 0 - No blocking related errors found
+ * 1 - Blocking resource is already in use
+ * 2 - Resource requested to be unblocked, was not blocked
+ *
+ * cache_controller_flush_status_hit
+ * The status that the cache controller returned on executing the
+ * flush command.
+ *
+ * 0 - miss; 1 - hit
+ *
+ * cache_controller_flush_status_desc_type
+ * Flush descriptor type
+ *
+ * cache_controller_flush_status_client_id
+ * Module who made the flush request
+ *
+ * In REO, this is always 0
+ *
+ * cache_controller_flush_status_error
+ * Error condition
+ *
+ * 0 - No error found
+ * 1 - HW interface is still busy
+ * 2 - Line currently locked. Used for one line flush command
+ * 3 - At least one line is still locked.
+ * Used for cache flush command.
+ *
+ * cache_controller_flush_count
+ * The number of lines that were actually flushed out
+ *
+ * looping_count
+ * A count value that indicates the number of times the producer of
+ * entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_UNBLOCK_CACHE_STATUS_INFO0_IS_ERR BIT(0)
+#define HAL_REO_UNBLOCK_CACHE_STATUS_INFO0_TYPE BIT(1)
+
+struct hal_reo_unblock_cache_status {
+ struct hal_reo_status_hdr hdr;
+ u32 info0;
+ u32 rsvd0[21];
+ u32 info1;
+} __packed;
+
+/* hal_reo_unblock_cache_status
+ * Producer: REO
+ * Consumer: SW
+ *
+ * status_hdr
+ * Details that can link this status with the original command. It
+ * also contains info on how long REO took to execute this command.
+ *
+ * error_detected
+ * 0 - No error has been detected while executing this command
+ * 1 - The blocking resource was not in use, and therefore it could
+ * not be unblocked.
+ *
+ * unblock_type
+ * Reference to the type of unblock command
+ * 0 - Unblock a blocking resource
+ * 1 - The entire cache usage is unblock
+ *
+ * looping_count
+ * A count value that indicates the number of times the producer of
+ * entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_FLUSH_TIMEOUT_STATUS_INFO0_IS_ERR BIT(0)
+#define HAL_REO_FLUSH_TIMEOUT_STATUS_INFO0_LIST_EMPTY BIT(1)
+
+#define HAL_REO_FLUSH_TIMEOUT_STATUS_INFO1_REL_DESC_COUNT GENMASK(15, 0)
+#define HAL_REO_FLUSH_TIMEOUT_STATUS_INFO1_FWD_BUF_COUNT GENMASK(31, 16)
+
+struct hal_reo_flush_timeout_list_status {
+ struct hal_reo_status_hdr hdr;
+ u32 info0;
+ u32 info1;
+ u32 rsvd0[20];
+ u32 info2;
+} __packed;
+
+/* hal_reo_flush_timeout_list_status
+ * Producer: REO
+ * Consumer: SW
+ *
+ * status_hdr
+ * Details that can link this status with the original command. It
+ * also contains info on how long REO took to execute this command.
+ *
+ * error_detected
+ * 0 - No error has been detected while executing this command
+ * 1 - Command not properly executed and returned with error
+ *
+ * timeout_list_empty
+ * When set, REO has depleted the timeout list and all entries are
+ * gone.
+ *
+ * release_desc_count
+ * Producer: SW; Consumer: REO
+ * The number of link descriptor released
+ *
+ * forward_buf_count
+ * Producer: SW; Consumer: REO
+ * The number of buffers forwarded to the REO destination rings
+ *
+ * looping_count
+ * A count value that indicates the number of times the producer of
+ * entries into this Ring has looped around the ring.
+ */
+
+#define HAL_REO_DESC_THRESH_STATUS_INFO0_THRESH_INDEX GENMASK(1, 0)
+#define HAL_REO_DESC_THRESH_STATUS_INFO1_LINK_DESC_COUNTER0 GENMASK(23, 0)
+#define HAL_REO_DESC_THRESH_STATUS_INFO2_LINK_DESC_COUNTER1 GENMASK(23, 0)
+#define HAL_REO_DESC_THRESH_STATUS_INFO3_LINK_DESC_COUNTER2 GENMASK(23, 0)
+#define HAL_REO_DESC_THRESH_STATUS_INFO4_LINK_DESC_COUNTER_SUM GENMASK(23, 0)
+
+struct hal_reo_desc_thresh_reached_status {
+ struct hal_reo_status_hdr hdr;
+ u32 info0;
+ u32 info1;
+ u32 info2;
+ u32 info3;
+ u32 info4;
+ u32 rsvd0[17];
+ u32 info5;
+} __packed;
+
+/* hal_reo_desc_thresh_reached_status
+ * Producer: REO
+ * Consumer: SW
+ *
+ * status_hdr
+ * Details that can link this status with the original command. It
+ * also contains info on how long REO took to execute this command.
+ *
+ * threshold_index
+ * The index of the threshold register whose value got reached
+ *
+ * link_descriptor_counter0
+ * link_descriptor_counter1
+ * link_descriptor_counter2
+ * link_descriptor_counter_sum
+ * Value of the respective counters at generation of this message
+ *
+ * looping_count
+ * A count value that indicates the number of times the producer of
+ * entries into this Ring has looped around the ring.
+ */
+
+#endif /* ATH11K_HAL_DESC_H */