new file mode 100644
@@ -0,0 +1,1212 @@
+/* SPDX-License-Identifier: BSD-3-Clause-Clear */
+/*
+ * Copyright (c) 2018-2019 The Linux Foundation. All rights reserved.
+ */
+#ifndef ATH11K_RX_DESC_H
+#define ATH11K_RX_DESC_H
+
+enum rx_desc_rxpcu_filter {
+ RX_DESC_RXPCU_FILTER_PASS,
+ RX_DESC_RXPCU_FILTER_MONITOR_CLIENT,
+ RX_DESC_RXPCU_FILTER_MONITOR_OTHER,
+};
+
+/* rxpcu_filter_pass
+ * This MPDU passed the normal frame filter programming of rxpcu.
+ *
+ * rxpcu_filter_monitor_client
+ * This MPDU did not pass the regular frame filter and would
+ * have been dropped, were it not for the frame fitting into the
+ * 'monitor_client' category.
+ *
+ * rxpcu_filter_monitor_other
+ * This MPDU did not pass the regular frame filter and also did
+ * not pass the rxpcu_monitor_client filter. It would have been
+ * dropped accept that it did pass the 'monitor_other' category.
+ */
+
+#define RX_DESC_INFO0_RXPCU_MPDU_FITLER GENMASK(1, 0)
+#define RX_DESC_INFO0_SW_FRAME_GRP_ID GENMASK(8, 2)
+
+enum rx_desc_sw_frame_grp_id {
+ RX_DESC_SW_FRAME_GRP_ID_NDP_FRAME,
+ RX_DESC_SW_FRAME_GRP_ID_MCAST_DATA,
+ RX_DESC_SW_FRAME_GRP_ID_UCAST_DATA,
+ RX_DESC_SW_FRAME_GRP_ID_NULL_DATA,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_0000,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_0001,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_0010,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_0011,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_0100,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_0101,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_0110,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_0111,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_1000,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_1001,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_1010,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_1011,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_1100,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_1101,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_1110,
+ RX_DESC_SW_FRAME_GRP_ID_MGMT_1111,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_0000,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_0001,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_0010,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_0011,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_0100,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_0101,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_0110,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_0111,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_1000,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_1001,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_1010,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_1011,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_1100,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_1101,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_1110,
+ RX_DESC_SW_FRAME_GRP_ID_CTRL_1111,
+ RX_DESC_SW_FRAME_GRP_ID_UNSUPPORTED,
+ RX_DESC_SW_FRAME_GRP_ID_PHY_ERR,
+};
+
+enum rx_desc_decap_type {
+ RX_DESC_DECAP_TYPE_RAW,
+ RX_DESC_DECAP_TYPE_NATIVE_WIFI,
+ RX_DESC_DECAP_TYPE_ETHERNET2_DIX,
+ RX_DESC_DECAP_TYPE_8023,
+};
+
+enum rx_desc_decrypt_status_code {
+ RX_DESC_DECRYPT_STATUS_CODE_OK,
+ RX_DESC_DECRYPT_STATUS_CODE_UNPROTECTED_FRAME,
+ RX_DESC_DECRYPT_STATUS_CODE_DATA_ERR,
+ RX_DESC_DECRYPT_STATUS_CODE_KEY_INVALID,
+ RX_DESC_DECRYPT_STATUS_CODE_PEER_ENTRY_INVALID,
+ RX_DESC_DECRYPT_STATUS_CODE_OTHER,
+};
+
+#define RX_ATTENTION_INFO1_FIRST_MPDU BIT(0)
+#define RX_ATTENTION_INFO1_RSVD_1A BIT(1)
+#define RX_ATTENTION_INFO1_MCAST_BCAST BIT(2)
+#define RX_ATTENTION_INFO1_AST_IDX_NOT_FOUND BIT(3)
+#define RX_ATTENTION_INFO1_AST_IDX_TIMEDOUT BIT(4)
+#define RX_ATTENTION_INFO1_POWER_MGMT BIT(5)
+#define RX_ATTENTION_INFO1_NON_QOS BIT(6)
+#define RX_ATTENTION_INFO1_NULL_DATA BIT(7)
+#define RX_ATTENTION_INFO1_MGMT_TYPE BIT(8)
+#define RX_ATTENTION_INFO1_CTRL_TYPE BIT(9)
+#define RX_ATTENTION_INFO1_MORE_DATA BIT(10)
+#define RX_ATTENTION_INFO1_EOSP BIT(11)
+#define RX_ATTENTION_INFO1_A_MSDU_ERROR BIT(12)
+#define RX_ATTENTION_INFO1_FRAGMENT BIT(13)
+#define RX_ATTENTION_INFO1_ORDER BIT(14)
+#define RX_ATTENTION_INFO1_CCE_MATCH BIT(15)
+#define RX_ATTENTION_INFO1_OVERFLOW_ERR BIT(16)
+#define RX_ATTENTION_INFO1_MSDU_LEN_ERR BIT(17)
+#define RX_ATTENTION_INFO1_TCP_UDP_CKSUM_FAIL BIT(18)
+#define RX_ATTENTION_INFO1_IP_CKSUM_FAIL BIT(19)
+#define RX_ATTENTION_INFO1_SA_IDX_INVALID BIT(20)
+#define RX_ATTENTION_INFO1_DA_IDX_INVALID BIT(21)
+#define RX_ATTENTION_INFO1_RSVD_1B BIT(22)
+#define RX_ATTENTION_INFO1_RX_IN_TX_DECRYPT_BYP BIT(23)
+#define RX_ATTENTION_INFO1_ENCRYPT_REQUIRED BIT(24)
+#define RX_ATTENTION_INFO1_DIRECTED BIT(25)
+#define RX_ATTENTION_INFO1_BUFFER_FRAGMENT BIT(26)
+#define RX_ATTENTION_INFO1_MPDU_LEN_ERR BIT(27)
+#define RX_ATTENTION_INFO1_TKIP_MIC_ERR BIT(28)
+#define RX_ATTENTION_INFO1_DECRYPT_ERR BIT(29)
+#define RX_ATTENTION_INFO1_UNDECRYPT_FRAME_ERR BIT(30)
+#define RX_ATTENTION_INFO1_FCS_ERR BIT(31)
+
+#define RX_ATTENTION_INFO2_FLOW_IDX_TIMEOUT BIT(0)
+#define RX_ATTENTION_INFO2_FLOW_IDX_INVALID BIT(1)
+#define RX_ATTENTION_INFO2_WIFI_PARSER_ERR BIT(2)
+#define RX_ATTENTION_INFO2_AMSDU_PARSER_ERR BIT(3)
+#define RX_ATTENTION_INFO2_SA_IDX_TIMEOUT BIT(4)
+#define RX_ATTENTION_INFO2_DA_IDX_TIMEOUT BIT(5)
+#define RX_ATTENTION_INFO2_MSDU_LIMIT_ERR BIT(6)
+#define RX_ATTENTION_INFO2_DA_IS_VALID BIT(7)
+#define RX_ATTENTION_INFO2_DA_IS_MCBC BIT(8)
+#define RX_ATTENTION_INFO2_SA_IS_VALID BIT(9)
+#define RX_ATTENTION_INFO2_DCRYPT_STATUS_CODE GENMASK(12, 10)
+#define RX_ATTENTION_INFO2_RX_BITMAP_NOT_UPDED BIT(13)
+#define RX_ATTENTION_INFO2_MSDU_DONE BIT(31)
+
+struct rx_attention {
+ __le16 info0;
+ __le16 phy_ppdu_id;
+ __le32 info1;
+ __le32 info2;
+} __packed;
+
+/* rx_attention
+ *
+ * rxpcu_mpdu_filter_in_category
+ * Field indicates what the reason was that this mpdu frame
+ * was allowed to come into the receive path by rxpcu. Values
+ * are defined in enum %RX_DESC_RXPCU_FILTER_*.
+ *
+ * sw_frame_group_id
+ * SW processes frames based on certain classifications. Values
+ * are defined in enum %RX_DESC_SW_FRAME_GRP_ID_*.
+ *
+ * phy_ppdu_id
+ * A ppdu counter value that PHY increments for every PPDU
+ * received. The counter value wraps around.
+ *
+ * first_mpdu
+ * Indicates the first MSDU of the PPDU. If both first_mpdu
+ * and last_mpdu are set in the MSDU then this is a not an
+ * A-MPDU frame but a stand alone MPDU. Interior MPDU in an
+ * A-MPDU shall have both first_mpdu and last_mpdu bits set to
+ * 0. The PPDU start status will only be valid when this bit
+ * is set.
+ *
+ * mcast_bcast
+ * Multicast / broadcast indicator. Only set when the MAC
+ * address 1 bit 0 is set indicating mcast/bcast and the BSSID
+ * matches one of the 4 BSSID registers. Only set when
+ * first_msdu is set.
+ *
+ * ast_index_not_found
+ * Only valid when first_msdu is set. Indicates no AST matching
+ * entries within the the max search count.
+ *
+ * ast_index_timeout
+ * Only valid when first_msdu is set. Indicates an unsuccessful
+ * search in the address search table due to timeout.
+ *
+ * power_mgmt
+ * Power management bit set in the 802.11 header. Only set
+ * when first_msdu is set.
+ *
+ * non_qos
+ * Set if packet is not a non-QoS data frame. Only set when
+ * first_msdu is set.
+ *
+ * null_data
+ * Set if frame type indicates either null data or QoS null
+ * data format. Only set when first_msdu is set.
+ *
+ * mgmt_type
+ * Set if packet is a management packet. Only set when
+ * first_msdu is set.
+ *
+ * ctrl_type
+ * Set if packet is a control packet. Only set when first_msdu
+ * is set.
+ *
+ * more_data
+ * Set if more bit in frame control is set. Only set when
+ * first_msdu is set.
+ *
+ * eosp
+ * Set if the EOSP (end of service period) bit in the QoS
+ * control field is set. Only set when first_msdu is set.
+ *
+ * a_msdu_error
+ * Set if number of MSDUs in A-MSDU is above a threshold or if the
+ * size of the MSDU is invalid. This receive buffer will contain
+ * all of the remainder of MSDUs in this MPDU w/o decapsulation.
+ *
+ * fragment
+ * Indicates that this is an 802.11 fragment frame. This is
+ * set when either the more_frag bit is set in the frame
+ * control or the fragment number is not zero. Only set when
+ * first_msdu is set.
+ *
+ * order
+ * Set if the order bit in the frame control is set. Only set
+ * when first_msdu is set.
+ *
+ * cce_match
+ * Indicates that this status has a corresponding MSDU that
+ * requires FW processing. The OLE will have classification
+ * ring mask registers which will indicate the ring(s) for
+ * packets and descriptors which need FW attention.
+ *
+ * overflow_err
+ * PCU Receive FIFO does not have enough space to store the
+ * full receive packet. Enough space is reserved in the
+ * receive FIFO for the status is written. This MPDU remaining
+ * packets in the PPDU will be filtered and no Ack response
+ * will be transmitted.
+ *
+ * msdu_length_err
+ * Indicates that the MSDU length from the 802.3 encapsulated
+ * length field extends beyond the MPDU boundary.
+ *
+ * tcp_udp_chksum_fail
+ * Indicates that the computed checksum (tcp_udp_chksum) did
+ * not match the checksum in the TCP/UDP header.
+ *
+ * ip_chksum_fail
+ * Indicates that the computed checksum did not match the
+ * checksum in the IP header.
+ *
+ * sa_idx_invalid
+ * Indicates no matching entry was found in the address search
+ * table for the source MAC address.
+ *
+ * da_idx_invalid
+ * Indicates no matching entry was found in the address search
+ * table for the destination MAC address.
+ *
+ * rx_in_tx_decrypt_byp
+ * Indicates that RX packet is not decrypted as Crypto is busy
+ * with TX packet processing.
+ *
+ * encrypt_required
+ * Indicates that this data type frame is not encrypted even if
+ * the policy for this MPDU requires encryption as indicated in
+ * the peer table key type.
+ *
+ * directed
+ * MPDU is a directed packet which means that the RA matched
+ * our STA addresses. In proxySTA it means that the TA matched
+ * an entry in our address search table with the corresponding
+ * 'no_ack' bit is the address search entry cleared.
+ *
+ * buffer_fragment
+ * Indicates that at least one of the rx buffers has been
+ * fragmented. If set the FW should look at the rx_frag_info
+ * descriptor described below.
+ *
+ * mpdu_length_err
+ * Indicates that the MPDU was pre-maturely terminated
+ * resulting in a truncated MPDU. Don't trust the MPDU length
+ * field.
+ *
+ * tkip_mic_err
+ * Indicates that the MPDU Michael integrity check failed
+ *
+ * decrypt_err
+ * Indicates that the MPDU decrypt integrity check failed
+ *
+ * fcs_err
+ * Indicates that the MPDU FCS check failed
+ *
+ * flow_idx_timeout
+ * Indicates an unsuccessful flow search due to the expiring of
+ * the search timer.
+ *
+ * flow_idx_invalid
+ * flow id is not valid.
+ *
+ * amsdu_parser_error
+ * A-MSDU could not be properly de-agregated.
+ *
+ * sa_idx_timeout
+ * Indicates an unsuccessful search for the source MAC address
+ * due to the expiring of the search timer.
+ *
+ * da_idx_timeout
+ * Indicates an unsuccessful search for the destination MAC
+ * address due to the expiring of the search timer.
+ *
+ * msdu_limit_error
+ * Indicates that the MSDU threshold was exceeded and thus
+ * all the rest of the MSDUs will not be scattered and will not
+ * be decasulated but will be DMA'ed in RAW format as a single
+ * MSDU buffer.
+ *
+ * da_is_valid
+ * Indicates that OLE found a valid DA entry.
+ *
+ * da_is_mcbc
+ * Field Only valid if da_is_valid is set. Indicates the DA address
+ * was a Multicast or Broadcast address.
+ *
+ * sa_is_valid
+ * Indicates that OLE found a valid SA entry.
+ *
+ * decrypt_status_code
+ * Field provides insight into the decryption performed. Values are
+ * defined in enum %RX_DESC_DECRYPT_STATUS_CODE*.
+ *
+ * rx_bitmap_not_updated
+ * Frame is received, but RXPCU could not update the receive bitmap
+ * due to (temporary) fifo constraints.
+ *
+ * msdu_done
+ * If set indicates that the RX packet data, RX header data, RX
+ * PPDU start descriptor, RX MPDU start/end descriptor, RX MSDU
+ * start/end descriptors and RX Attention descriptor are all
+ * valid. This bit must be in the last octet of the
+ * descriptor.
+ */
+
+#define RX_MPDU_START_INFO0_NDP_FRAME BIT(9)
+#define RX_MPDU_START_INFO0_PHY_ERR BIT(10)
+#define RX_MPDU_START_INFO0_PHY_ERR_MPDU_HDR BIT(11)
+#define RX_MPDU_START_INFO0_PROTO_VER_ERR BIT(12)
+#define RX_MPDU_START_INFO0_AST_LOOKUP_VALID BIT(13)
+
+#define RX_MPDU_START_INFO1_MPDU_CTRL_VALID BIT(0)
+#define RX_MPDU_START_INFO1_MPDU_DUR_VALID BIT(1)
+#define RX_MPDU_START_INFO1_MAC_ADDR1_VALID BIT(2)
+#define RX_MPDU_START_INFO1_MAC_ADDR2_VALID BIT(3)
+#define RX_MPDU_START_INFO1_MAC_ADDR3_VALID BIT(4)
+#define RX_MPDU_START_INFO1_MAC_ADDR4_VALID BIT(5)
+#define RX_MPDU_START_INFO1_MPDU_SEQ_CTRL_VALID BIT(6)
+#define RX_MPDU_START_INFO1_MPDU_QOS_CTRL_VALID BIT(7)
+#define RX_MPDU_START_INFO1_MPDU_HT_CTRL_VALID BIT(8)
+#define RX_MPDU_START_INFO1_ENCRYPT_INFO_VALID BIT(9)
+#define RX_MPDU_START_INFO1_MPDU_FRAG_NUMBER GENMASK(13, 10)
+#define RX_MPDU_START_INFO1_MORE_FRAG_FLAG BIT(14)
+#define RX_MPDU_START_INFO1_FROM_DS BIT(16)
+#define RX_MPDU_START_INFO1_TO_DS BIT(17)
+#define RX_MPDU_START_INFO1_ENCRYPTED BIT(18)
+#define RX_MPDU_START_INFO1_MPDU_RETRY BIT(19)
+#define RX_MPDU_START_INFO1_MPDU_SEQ_NUM GENMASK(31, 20)
+
+#define RX_MPDU_START_INFO2_EPD_EN BIT(0)
+#define RX_MPDU_START_INFO2_ALL_FRAME_ENCPD BIT(1)
+#define RX_MPDU_START_INFO2_ENC_TYPE GENMASK(5, 2)
+#define RX_MPDU_START_INFO2_VAR_WEP_KEY_WIDTH GENMASK(7, 6)
+#define RX_MPDU_START_INFO2_MESH_STA BIT(8)
+#define RX_MPDU_START_INFO2_BSSID_HIT BIT(9)
+#define RX_MPDU_START_INFO2_BSSID_NUM GENMASK(13, 10)
+#define RX_MPDU_START_INFO2_TID GENMASK(17, 14)
+
+#define RX_MPDU_START_INFO3_REO_DEST_IND GENMASK(4, 0)
+#define RX_MPDU_START_INFO3_FLOW_ID_TOEPLITZ BIT(7)
+#define RX_MPDU_START_INFO3_PKT_SEL_FP_UCAST_DATA BIT(8)
+#define RX_MPDU_START_INFO3_PKT_SEL_FP_MCAST_DATA BIT(9)
+#define RX_MPDU_START_INFO3_PKT_SEL_FP_CTRL_BAR BIT(10)
+#define RX_MPDU_START_INFO3_RXDMA0_SRC_RING_SEL GENMASK(12, 11)
+#define RX_MPDU_START_INFO3_RXDMA0_DST_RING_SEL GENMASK(14, 13)
+
+#define RX_MPDU_START_INFO4_REO_QUEUE_DESC_HI GENMASK(7, 0)
+#define RX_MPDU_START_INFO4_RECV_QUEUE_NUM GENMASK(23, 8)
+#define RX_MPDU_START_INFO4_PRE_DELIM_ERR_WARN BIT(24)
+#define RX_MPDU_START_INFO4_FIRST_DELIM_ERR BIT(25)
+
+#define RX_MPDU_START_INFO5_KEY_ID GENMASK(7, 0)
+#define RX_MPDU_START_INFO5_NEW_PEER_ENTRY BIT(8)
+#define RX_MPDU_START_INFO5_DECRYPT_NEEDED BIT(9)
+#define RX_MPDU_START_INFO5_DECAP_TYPE GENMASK(11, 10)
+#define RX_MPDU_START_INFO5_VLAN_TAG_C_PADDING BIT(12)
+#define RX_MPDU_START_INFO5_VLAN_TAG_S_PADDING BIT(13)
+#define RX_MPDU_START_INFO5_STRIP_VLAN_TAG_C BIT(14)
+#define RX_MPDU_START_INFO5_STRIP_VLAN_TAG_S BIT(15)
+#define RX_MPDU_START_INFO5_PRE_DELIM_COUNT GENMASK(27, 16)
+#define RX_MPDU_START_INFO5_AMPDU_FLAG BIT(28)
+#define RX_MPDU_START_INFO5_BAR_FRAME BIT(29)
+
+#define RX_MPDU_START_INFO6_MPDU_LEN GENMASK(13, 0)
+#define RX_MPDU_START_INFO6_FIRST_MPDU BIT(14)
+#define RX_MPDU_START_INFO6_MCAST_BCAST BIT(15)
+#define RX_MPDU_START_INFO6_AST_IDX_NOT_FOUND BIT(16)
+#define RX_MPDU_START_INFO6_AST_IDX_TIMEOUT BIT(17)
+#define RX_MPDU_START_INFO6_POWER_MGMT BIT(18)
+#define RX_MPDU_START_INFO6_NON_QOS BIT(19)
+#define RX_MPDU_START_INFO6_NULL_DATA BIT(20)
+#define RX_MPDU_START_INFO6_MGMT_TYPE BIT(21)
+#define RX_MPDU_START_INFO6_CTRL_TYPE BIT(22)
+#define RX_MPDU_START_INFO6_MORE_DATA BIT(23)
+#define RX_MPDU_START_INFO6_EOSP BIT(24)
+#define RX_MPDU_START_INFO6_FRAGMENT BIT(25)
+#define RX_MPDU_START_INFO6_ORDER BIT(26)
+#define RX_MPDU_START_INFO6_UAPSD_TRIGGER BIT(27)
+#define RX_MPDU_START_INFO6_ENCRYPT_REQUIRED BIT(28)
+#define RX_MPDU_START_INFO6_DIRECTED BIT(29)
+
+#define RX_MPDU_START_RAW_MPDU BIT(0)
+
+struct rx_mpdu_start {
+ __le16 info0;
+ __le16 phy_ppdu_id;
+ __le16 ast_index;
+ __le16 sw_peer_id;
+ __le32 info1;
+ __le32 info2;
+ __le32 pn[4];
+ __le32 peer_meta_data;
+ __le32 info3;
+ __le32 reo_queue_desc_lo;
+ __le32 info4;
+ __le32 info5;
+ __le32 info6;
+ __le16 frame_ctrl;
+ __le16 duration;
+ u8 addr1[ETH_ALEN];
+ u8 addr2[ETH_ALEN];
+ u8 addr3[ETH_ALEN];
+ __le16 seq_ctrl;
+ u8 addr4[ETH_ALEN];
+ __le16 qos_ctrl;
+ __le32 ht_ctrl;
+ __le32 raw;
+} __packed;
+
+/* rx_mpdu_start
+ *
+ * rxpcu_mpdu_filter_in_category
+ * Field indicates what the reason was that this mpdu frame
+ * was allowed to come into the receive path by rxpcu. Values
+ * are defined in enum %RX_DESC_RXPCU_FILTER_*.
+ * Note: for ndp frame, if it was expected because the preceding
+ * NDPA was filter_pass, the setting rxpcu_filter_pass will be
+ * used. This setting will also be used for every ndp frame in
+ * case Promiscuous mode is enabled.
+ *
+ * sw_frame_group_id
+ * SW processes frames based on certain classifications. Values
+ * are defined in enum %RX_DESC_SW_FRAME_GRP_ID_*.
+ *
+ * ndp_frame
+ * Indicates that the received frame was an NDP frame.
+ *
+ * phy_err
+ * Indicates that PHY error was received before MAC received data.
+ *
+ * phy_err_during_mpdu_header
+ * PHY error was received before MAC received the complete MPDU
+ * header which was needed for proper decoding.
+ *
+ * protocol_version_err
+ * RXPCU detected a version error in the frame control field.
+ *
+ * ast_based_lookup_valid
+ * AST based lookup for this frame has found a valid result.
+ *
+ * phy_ppdu_id
+ * A ppdu counter value that PHY increments for every PPDU
+ * received. The counter value wraps around.
+ *
+ * ast_index
+ * This field indicates the index of the AST entry corresponding
+ * to this MPDU. It is provided by the GSE module instantiated in
+ * RXPCU. A value of 0xFFFF indicates an invalid AST index.
+ *
+ * sw_peer_id
+ * This field indicates a unique peer identifier. It is set equal
+ * to field 'sw_peer_id' from the AST entry.
+ *
+ * mpdu_frame_control_valid, mpdu_duration_valid, mpdu_qos_control_valid,
+ * mpdu_ht_control_valid, frame_encryption_info_valid
+ * Indicates that each fields have valid entries.
+ *
+ * mac_addr_adx_valid
+ * Corresponding mac_addr_adx_{lo/hi} has valid entries.
+ *
+ * from_ds, to_ds
+ * Valid only when mpdu_frame_control_valid is set. Indicates that
+ * frame is received from DS and sent to DS.
+ *
+ * encrypted
+ * Protected bit from the frame control.
+ *
+ * mpdu_retry
+ * Retry bit from frame control. Only valid when first_msdu is set.
+ *
+ * mpdu_sequence_number
+ * The sequence number from the 802.11 header.
+ *
+ * epd_en
+ * If set, use EPD instead of LPD.
+ *
+ * all_frames_shall_be_encrypted
+ * If set, all frames (data only?) shall be encrypted. If not,
+ * RX CRYPTO shall set an error flag.
+ *
+ * encrypt_type
+ * Values are defined in enum %HAL_ENCRYPT_TYPE_.
+ *
+ * mesh_sta
+ * Indicates a Mesh (11s) STA.
+ *
+ * bssid_hit
+ * BSSID of the incoming frame matched one of the 8 BSSID
+ * register values.
+ *
+ * bssid_number
+ * This number indicates which one out of the 8 BSSID register
+ * values matched the incoming frame.
+ *
+ * tid
+ * TID field in the QoS control field
+ *
+ * pn
+ * The PN number.
+ *
+ * peer_meta_data
+ * Meta data that SW has programmed in the Peer table entry
+ * of the transmitting STA.
+ *
+ * rx_reo_queue_desc_addr_lo
+ * Address (lower 32 bits) of the REO queue descriptor.
+ *
+ * rx_reo_queue_desc_addr_hi
+ * Address (upper 8 bits) of the REO queue descriptor.
+ *
+ * receive_queue_number
+ * Indicates the MPDU queue ID to which this MPDU link
+ * descriptor belongs.
+ *
+ * pre_delim_err_warning
+ * Indicates that a delimiter FCS error was found in between the
+ * previous MPDU and this MPDU. Note that this is just a warning,
+ * and does not mean that this MPDU is corrupted in any way. If
+ * it is, there will be other errors indicated such as FCS or
+ * decrypt errors.
+ *
+ * first_delim_err
+ * Indicates that the first delimiter had a FCS failure.
+ *
+ * key_id
+ * The key ID octet from the IV.
+ *
+ * new_peer_entry
+ * Set if new RX_PEER_ENTRY TLV follows. If clear, RX_PEER_ENTRY
+ * doesn't follow so RX DECRYPTION module either uses old peer
+ * entry or not decrypt.
+ *
+ * decrypt_needed
+ * When RXPCU sets bit 'ast_index_not_found or ast_index_timeout',
+ * RXPCU will also ensure that this bit is NOT set. CRYPTO for that
+ * reason only needs to evaluate this bit and non of the other ones
+ *
+ * decap_type
+ * Used by the OLE during decapsulation. Values are defined in
+ * enum %MPDU_START_DECAP_TYPE_*.
+ *
+ * rx_insert_vlan_c_tag_padding
+ * rx_insert_vlan_s_tag_padding
+ * Insert 4 byte of all zeros as VLAN tag or double VLAN tag if
+ * the rx payload does not have VLAN.
+ *
+ * strip_vlan_c_tag_decap
+ * strip_vlan_s_tag_decap
+ * Strip VLAN or double VLAN during decapsulation.
+ *
+ * pre_delim_count
+ * The number of delimiters before this MPDU. Note that this
+ * number is cleared at PPDU start. If this MPDU is the first
+ * received MPDU in the PPDU and this MPDU gets filtered-in,
+ * this field will indicate the number of delimiters located
+ * after the last MPDU in the previous PPDU.
+ *
+ * If this MPDU is located after the first received MPDU in
+ * an PPDU, this field will indicate the number of delimiters
+ * located between the previous MPDU and this MPDU.
+ *
+ * ampdu_flag
+ * Received frame was part of an A-MPDU.
+ *
+ * bar_frame
+ * Received frame is a BAR frame
+ *
+ * mpdu_length
+ * MPDU length before decapsulation.
+ *
+ * first_mpdu..directed
+ * See definition in RX attention descriptor
+ *
+ */
+
+enum rx_msdu_start_pkt_type {
+ RX_MSDU_START_PKT_TYPE_11A,
+ RX_MSDU_START_PKT_TYPE_11B,
+ RX_MSDU_START_PKT_TYPE_11N,
+ RX_MSDU_START_PKT_TYPE_11AC,
+ RX_MSDU_START_PKT_TYPE_11AX,
+};
+
+enum rx_msdu_start_sgi {
+ RX_MSDU_START_SGI_0_8_US,
+ RX_MSDU_START_SGI_0_4_US,
+ RX_MSDU_START_SGI_1_6_US,
+ RX_MSDU_START_SGI_3_2_US,
+};
+
+enum rx_msdu_start_recv_bw {
+ RX_MSDU_START_RECV_BW_20MHZ,
+ RX_MSDU_START_RECV_BW_40MHZ,
+ RX_MSDU_START_RECV_BW_80MHZ,
+ RX_MSDU_START_RECV_BW_160MHZ,
+};
+
+enum rx_msdu_start_reception_type {
+ RX_MSDU_START_RECEPTION_TYPE_SU,
+ RX_MSDU_START_RECEPTION_TYPE_DL_MU_MIMO,
+ RX_MSDU_START_RECEPTION_TYPE_DL_MU_OFDMA,
+ RX_MSDU_START_RECEPTION_TYPE_DL_MU_OFDMA_MIMO,
+ RX_MSDU_START_RECEPTION_TYPE_UL_MU_MIMO,
+ RX_MSDU_START_RECEPTION_TYPE_UL_MU_OFDMA,
+ RX_MSDU_START_RECEPTION_TYPE_UL_MU_OFDMA_MIMO,
+};
+
+#define RX_MSDU_START_INFO1_MSDU_LENGTH GENMASK(13, 0)
+#define RX_MSDU_START_INFO1_RSVD_1A BIT(14)
+#define RX_MSDU_START_INFO1_IPSEC_ESP BIT(15)
+#define RX_MSDU_START_INFO1_L3_OFFSET GENMASK(22, 16)
+#define RX_MSDU_START_INFO1_IPSEC_AH BIT(23)
+#define RX_MSDU_START_INFO1_L4_OFFSET GENMASK(31, 24)
+
+#define RX_MSDU_START_INFO2_MSDU_NUMBER GENMASK(7, 0)
+#define RX_MSDU_START_INFO2_DECAP_TYPE GENMASK(9, 8)
+#define RX_MSDU_START_INFO2_IPV4 BIT(10)
+#define RX_MSDU_START_INFO2_IPV6 BIT(11)
+#define RX_MSDU_START_INFO2_TCP BIT(12)
+#define RX_MSDU_START_INFO2_UDP BIT(13)
+#define RX_MSDU_START_INFO2_IP_FRAG BIT(14)
+#define RX_MSDU_START_INFO2_TCP_ONLY_ACK BIT(15)
+#define RX_MSDU_START_INFO2_DA_IS_BCAST_MCAST BIT(16)
+#define RX_MSDU_START_INFO2_SELECTED_TOEPLITZ_HASH GENMASK(18, 17)
+#define RX_MSDU_START_INFO2_IP_FIXED_HDR_VALID BIT(19)
+#define RX_MSDU_START_INFO2_IP_EXTN_HDR_VALID BIT(20)
+#define RX_MSDU_START_INFO2_IP_TCP_UDP_HDR_VALID BIT(21)
+#define RX_MSDU_START_INFO2_MESH_CTRL_PRESENT BIT(22)
+#define RX_MSDU_START_INFO2_LDPC BIT(23)
+#define RX_MSDU_START_INFO2_IP4_IP6_NXT_HDR GENMASK(31, 24)
+#define RX_MSDU_START_INFO2_DECAP_FORMAT GENMASK(9, 8)
+
+#define RX_MSDU_START_INFO3_USER_RSSI GENMASK(7, 0)
+#define RX_MSDU_START_INFO3_PKT_TYPE GENMASK(11, 8)
+#define RX_MSDU_START_INFO3_STBC BIT(12)
+#define RX_MSDU_START_INFO3_SGI GENMASK(14, 13)
+#define RX_MSDU_START_INFO3_RATE_MCS GENMASK(18, 15)
+#define RX_MSDU_START_INFO3_RECV_BW GENMASK(20, 19)
+#define RX_MSDU_START_INFO3_RECEPTION_TYPE GENMASK(23, 21)
+#define RX_MSDU_START_INFO3_MIMO_SS_BITMAP GENMASK(31, 24)
+
+struct rx_msdu_start {
+ __le16 info0;
+ __le16 phy_ppdu_id;
+ __le32 info1;
+ __le32 info2;
+ __le32 toeplitz_hash;
+ __le32 flow_id_toeplitz;
+ __le32 info3;
+ __le32 ppdu_start_timestamp;
+ __le32 phy_meta_data;
+} __packed;
+
+/* rx_msdu_start
+ *
+ * rxpcu_mpdu_filter_in_category
+ * Field indicates what the reason was that this mpdu frame
+ * was allowed to come into the receive path by rxpcu. Values
+ * are defined in enum %RX_DESC_RXPCU_FILTER_*.
+ *
+ * sw_frame_group_id
+ * SW processes frames based on certain classifications. Values
+ * are defined in enum %RX_DESC_SW_FRAME_GRP_ID_*.
+ *
+ * phy_ppdu_id
+ * A ppdu counter value that PHY increments for every PPDU
+ * received. The counter value wraps around.
+ *
+ * msdu_length
+ * MSDU length in bytes after decapsulation.
+ *
+ * ipsec_esp
+ * Set if IPv4/v6 packet is using IPsec ESP.
+ *
+ * l3_offset
+ * Depending upon mode bit, this field either indicates the
+ * L3 offset in bytes from the start of the RX_HEADER or the IP
+ * offset in bytes from the start of the packet after
+ * decapsulation. The latter is only valid if ipv4_proto or
+ * ipv6_proto is set.
+ *
+ * ipsec_ah
+ * Set if IPv4/v6 packet is using IPsec AH
+ *
+ * l4_offset
+ * Depending upon mode bit, this field either indicates the
+ * L4 offset nin bytes from the start of RX_HEADER (only valid
+ * if either ipv4_proto or ipv6_proto is set to 1) or indicates
+ * the offset in bytes to the start of TCP or UDP header from
+ * the start of the IP header after decapsulation (Only valid if
+ * tcp_proto or udp_proto is set). The value 0 indicates that
+ * the offset is longer than 127 bytes.
+ *
+ * msdu_number
+ * Indicates the MSDU number within a MPDU. This value is
+ * reset to zero at the start of each MPDU. If the number of
+ * MSDU exceeds 255 this number will wrap using modulo 256.
+ *
+ * decap_type
+ * Indicates the format after decapsulation. Values are defined in
+ * enum %MPDU_START_DECAP_TYPE_*.
+ *
+ * ipv4_proto
+ * Set if L2 layer indicates IPv4 protocol.
+ *
+ * ipv6_proto
+ * Set if L2 layer indicates IPv6 protocol.
+ *
+ * tcp_proto
+ * Set if the ipv4_proto or ipv6_proto are set and the IP protocol
+ * indicates TCP.
+ *
+ * udp_proto
+ * Set if the ipv4_proto or ipv6_proto are set and the IP protocol
+ * indicates UDP.
+ *
+ * ip_frag
+ * Indicates that either the IP More frag bit is set or IP frag
+ * number is non-zero. If set indicates that this is a fragmented
+ * IP packet.
+ *
+ * tcp_only_ack
+ * Set if only the TCP Ack bit is set in the TCP flags and if
+ * the TCP payload is 0.
+ *
+ * da_is_bcast_mcast
+ * The destination address is broadcast or multicast.
+ *
+ * toeplitz_hash
+ * Actual chosen Hash.
+ * 0 - Toeplitz hash of 2-tuple (IP source address, IP
+ * destination address)
+ * 1 - Toeplitz hash of 4-tuple (IP source address,
+ * IP destination address, L4 (TCP/UDP) source port,
+ * L4 (TCP/UDP) destination port)
+ * 2 - Toeplitz of flow_id
+ * 3 - Zero is used
+ *
+ * ip_fixed_header_valid
+ * Fixed 20-byte IPv4 header or 40-byte IPv6 header parsed
+ * fully within first 256 bytes of the packet
+ *
+ * ip_extn_header_valid
+ * IPv6/IPv6 header, including IPv4 options and
+ * recognizable extension headers parsed fully within first 256
+ * bytes of the packet
+ *
+ * tcp_udp_header_valid
+ * Fixed 20-byte TCP (excluding TCP options) or 8-byte UDP
+ * header parsed fully within first 256 bytes of the packet
+ *
+ * mesh_control_present
+ * When set, this MSDU includes the 'Mesh Control' field
+ *
+ * ldpc
+ *
+ * ip4_protocol_ip6_next_header
+ * For IPv4, this is the 8 bit protocol field set). For IPv6 this
+ * is the 8 bit next_header field.
+ *
+ * toeplitz_hash_2_or_4
+ * Controlled by RxOLE register - If register bit set to 0,
+ * Toeplitz hash is computed over 2-tuple IPv4 or IPv6 src/dest
+ * addresses; otherwise, toeplitz hash is computed over 4-tuple
+ * IPv4 or IPv6 src/dest addresses and src/dest ports.
+ *
+ * flow_id_toeplitz
+ * Toeplitz hash of 5-tuple
+ * {IP source address, IP destination address, IP source port, IP
+ * destination port, L4 protocol} in case of non-IPSec.
+ *
+ * In case of IPSec - Toeplitz hash of 4-tuple
+ * {IP source address, IP destination address, SPI, L4 protocol}
+ *
+ * The relevant Toeplitz key registers are provided in RxOLE's
+ * instance of common parser module. These registers are separate
+ * from the Toeplitz keys used by ASE/FSE modules inside RxOLE.
+ * The actual value will be passed on from common parser module
+ * to RxOLE in one of the WHO_* TLVs.
+ *
+ * user_rssi
+ * RSSI for this user
+ *
+ * pkt_type
+ * Values are defined in enum %RX_MSDU_START_PKT_TYPE_*.
+ *
+ * stbc
+ * When set, use STBC transmission rates.
+ *
+ * sgi
+ * Field only valid when pkt type is HT, VHT or HE. Values are
+ * defined in enum %RX_MSDU_START_SGI_*.
+ *
+ * rate_mcs
+ * MCS Rate used.
+ *
+ * receive_bandwidth
+ * Full receive Bandwidth. Values are defined in enum
+ * %RX_MSDU_START_RECV_*.
+ *
+ * reception_type
+ * Indicates what type of reception this is and defined in enum
+ * %RX_MSDU_START_RECEPTION_TYPE_*.
+ *
+ * mimo_ss_bitmap
+ * Field only valid when
+ * Reception_type is RX_MSDU_START_RECEPTION_TYPE_DL_MU_MIMO or
+ * RX_MSDU_START_RECEPTION_TYPE_DL_MU_OFDMA_MIMO.
+ *
+ * Bitmap, with each bit indicating if the related spatial
+ * stream is used for this STA
+ *
+ * LSB related to SS 0
+ *
+ * 0 - spatial stream not used for this reception
+ * 1 - spatial stream used for this reception
+ *
+ * ppdu_start_timestamp
+ * Timestamp that indicates when the PPDU that contained this MPDU
+ * started on the medium.
+ *
+ * phy_meta_data
+ * SW programmed Meta data provided by the PHY. Can be used for SW
+ * to indicate the channel the device is on.
+ */
+
+#define RX_MSDU_END_INFO0_RXPCU_MPDU_FITLER GENMASK(1, 0)
+#define RX_MSDU_END_INFO0_SW_FRAME_GRP_ID GENMASK(8, 2)
+
+#define RX_MSDU_END_INFO1_KEY_ID GENMASK(7, 0)
+#define RX_MSDU_END_INFO1_CCE_SUPER_RULE GENMASK(13, 8)
+#define RX_MSDU_END_INFO1_CCND_TRUNCATE BIT(14)
+#define RX_MSDU_END_INFO1_CCND_CCE_DIS BIT(15)
+#define RX_MSDU_END_INFO1_EXT_WAPI_PN GENMASK(31, 16)
+
+#define RX_MSDU_END_INFO2_REPORTED_MPDU_LEN GENMASK(13, 0)
+#define RX_MSDU_END_INFO2_FIRST_MSDU BIT(14)
+#define RX_MSDU_END_INFO2_LAST_MSDU BIT(15)
+#define RX_MSDU_END_INFO2_SA_IDX_TIMEOUT BIT(16)
+#define RX_MSDU_END_INFO2_DA_IDX_TIMEOUT BIT(17)
+#define RX_MSDU_END_INFO2_MSDU_LIMIT_ERR BIT(18)
+#define RX_MSDU_END_INFO2_FLOW_IDX_TIMEOUT BIT(19)
+#define RX_MSDU_END_INFO2_FLOW_IDX_INVALID BIT(20)
+#define RX_MSDU_END_INFO2_WIFI_PARSER_ERR BIT(21)
+#define RX_MSDU_END_INFO2_AMSDU_PARSET_ERR BIT(22)
+#define RX_MSDU_END_INFO2_SA_IS_VALID BIT(23)
+#define RX_MSDU_END_INFO2_DA_IS_VALID BIT(24)
+#define RX_MSDU_END_INFO2_DA_IS_MCBC BIT(25)
+#define RX_MSDU_END_INFO2_L3_HDR_PADDING GENMASK(27, 26)
+
+#define RX_MSDU_END_INFO3_TCP_FLAG GENMASK(8, 0)
+#define RX_MSDU_END_INFO3_LRO_ELIGIBLE BIT(9)
+
+#define RX_MSDU_END_INFO4_DA_OFFSET GENMASK(5, 0)
+#define RX_MSDU_END_INFO4_SA_OFFSET GENMASK(11, 6)
+#define RX_MSDU_END_INFO4_DA_OFFSET_VALID BIT(12)
+#define RX_MSDU_END_INFO4_SA_OFFSET_VALID BIT(13)
+#define RX_MSDU_END_INFO4_L3_TYPE GENMASK(31, 16)
+
+#define RX_MSDU_END_INFO5_MSDU_DROP BIT(0)
+#define RX_MSDU_END_INFO5_REO_DEST_IND GENMASK(5, 1)
+#define RX_MSDU_END_INFO5_FLOW_IDX GENMASK(25, 6)
+
+struct rx_msdu_end {
+ __le16 info0;
+ __le16 phy_ppdu_id;
+ __le16 ip_hdr_cksum;
+ __le16 tcp_udp_cksum;
+ __le32 info1;
+ __le32 ext_wapi_pn[2];
+ __le32 info2;
+ __le32 ipv6_options_crc;
+ __le32 tcp_seq_num;
+ __le32 tcp_ack_num;
+ __le16 info3;
+ __le16 window_size;
+ __le32 info4;
+ __le32 rule_indication[2];
+ __le16 sa_idx;
+ __le16 da_idx;
+ __le32 info5;
+ __le32 fse_metadata;
+ __le16 cce_metadata;
+ __le16 sa_sw_peer_id;
+} __packed;
+
+/* rx_msdu_end
+ *
+ * rxpcu_mpdu_filter_in_category
+ * Field indicates what the reason was that this mpdu frame
+ * was allowed to come into the receive path by rxpcu. Values
+ * are defined in enum %RX_DESC_RXPCU_FILTER_*.
+ *
+ * sw_frame_group_id
+ * SW processes frames based on certain classifications. Values
+ * are defined in enum %RX_DESC_SW_FRAME_GRP_ID_*.
+ *
+ * phy_ppdu_id
+ * A ppdu counter value that PHY increments for every PPDU
+ * received. The counter value wraps around.
+ *
+ * ip_hdr_cksum
+ * This can include the IP header checksum or the pseudo
+ * header checksum used by TCP/UDP checksum.
+ *
+ * tcp_udp_chksum
+ * The value of the computed TCP/UDP checksum. A mode bit
+ * selects whether this checksum is the full checksum or the
+ * partial checksum which does not include the pseudo header.
+ *
+ * key_id
+ * The key ID octet from the IV. Only valid when first_msdu is set.
+ *
+ * cce_super_rule
+ * Indicates the super filter rule.
+ *
+ * cce_classify_not_done_truncate
+ * Classification failed due to truncated frame.
+ *
+ * cce_classify_not_done_cce_dis
+ * Classification failed due to CCE global disable
+ *
+ * ext_wapi_pn*
+ * Extension PN (packet number) which is only used by WAPI.
+ *
+ * reported_mpdu_length
+ * MPDU length before decapsulation. Only valid when first_msdu is
+ * set. This field is taken directly from the length field of the
+ * A-MPDU delimiter or the preamble length field for non-A-MPDU
+ * frames.
+ *
+ * first_msdu
+ * Indicates the first MSDU of A-MSDU. If both first_msdu and
+ * last_msdu are set in the MSDU then this is a non-aggregated MSDU
+ * frame: normal MPDU. Interior MSDU in an A-MSDU shall have both
+ * first_mpdu and last_mpdu bits set to 0.
+ *
+ * last_msdu
+ * Indicates the last MSDU of the A-MSDU. MPDU end status is only
+ * valid when last_msdu is set.
+ *
+ * sa_idx_timeout
+ * Indicates an unsuccessful MAC source address search due to the
+ * expiring of the search timer.
+ *
+ * da_idx_timeout
+ * Indicates an unsuccessful MAC destination address search due to
+ * the expiring of the search timer.
+ *
+ * msdu_limit_error
+ * Indicates that the MSDU threshold was exceeded and thus all the
+ * rest of the MSDUs will not be scattered and will not be
+ * decapsulated but will be DMA'ed in RAW format as a single MSDU.
+ *
+ * flow_idx_timeout
+ * Indicates an unsuccessful flow search due to the expiring of
+ * the search timer.
+ *
+ * flow_idx_invalid
+ * flow id is not valid.
+ *
+ * amsdu_parser_error
+ * A-MSDU could not be properly de-agregated.
+ *
+ * sa_is_valid
+ * Indicates that OLE found a valid SA entry.
+ *
+ * da_is_valid
+ * Indicates that OLE found a valid DA entry.
+ *
+ * da_is_mcbc
+ * Field Only valid if da_is_valid is set. Indicates the DA address
+ * was a Multicast of Broadcast address.
+ *
+ * l3_header_padding
+ * Number of bytes padded to make sure that the L3 header will
+ * always start of a Dword boundary.
+ *
+ * ipv6_options_crc
+ * 32 bit CRC computed out of IP v6 extension headers.
+ *
+ * tcp_seq_number
+ * TCP sequence number.
+ *
+ * tcp_ack_number
+ * TCP acknowledge number.
+ *
+ * tcp_flag
+ * TCP flags {NS, CWR, ECE, URG, ACK, PSH, RST, SYN, FIN}.
+ *
+ * lro_eligible
+ * Computed out of TCP and IP fields to indicate that this
+ * MSDU is eligible for LRO.
+ *
+ * window_size
+ * TCP receive window size.
+ *
+ * da_offset
+ * Offset into MSDU buffer for DA.
+ *
+ * sa_offset
+ * Offset into MSDU buffer for SA.
+ *
+ * da_offset_valid
+ * da_offset field is valid. This will be set to 0 in case
+ * of a dynamic A-MSDU when DA is compressed.
+ *
+ * sa_offset_valid
+ * sa_offset field is valid. This will be set to 0 in case
+ * of a dynamic A-MSDU when SA is compressed.
+ *
+ * l3_type
+ * The 16-bit type value indicating the type of L3 later
+ * extracted from LLC/SNAP, set to zero if SNAP is not
+ * available.
+ *
+ * rule_indication
+ * Bitmap indicating which of rules have matched.
+ *
+ * sa_idx
+ * The offset in the address table which matches MAC source address
+ *
+ * da_idx
+ * The offset in the address table which matches MAC destination
+ * address.
+ *
+ * msdu_drop
+ * REO shall drop this MSDU and not forward it to any other ring.
+ *
+ * reo_destination_indication
+ * The id of the reo exit ring where the msdu frame shall push
+ * after (MPDU level) reordering has finished. Values are defined
+ * in enum %HAL_RX_MSDU_DESC_REO_DEST_IND_.
+ *
+ * flow_idx
+ * Flow table index.
+ *
+ * fse_metadata
+ * FSE related meta data.
+ *
+ * cce_metadata
+ * CCE related meta data.
+ *
+ * sa_sw_peer_id
+ * sw_peer_id from the address search entry corresponding to the
+ * source address of the MSDU.
+ */
+
+enum rx_mpdu_end_rxdma_dest_ring {
+ RX_MPDU_END_RXDMA_DEST_RING_RELEASE,
+ RX_MPDU_END_RXDMA_DEST_RING_FW,
+ RX_MPDU_END_RXDMA_DEST_RING_SW,
+ RX_MPDU_END_RXDMA_DEST_RING_REO,
+};
+
+#define RX_MPDU_END_INFO1_UNSUP_KTYPE_SHORT_FRAME BIT(11)
+#define RX_MPDU_END_INFO1_RX_IN_TX_DECRYPT_BYT BIT(12)
+#define RX_MPDU_END_INFO1_OVERFLOW_ERR BIT(13)
+#define RX_MPDU_END_INFO1_MPDU_LEN_ERR BIT(14)
+#define RX_MPDU_END_INFO1_TKIP_MIC_ERR BIT(15)
+#define RX_MPDU_END_INFO1_DECRYPT_ERR BIT(16)
+#define RX_MPDU_END_INFO1_UNENCRYPTED_FRAME_ERR BIT(17)
+#define RX_MPDU_END_INFO1_PN_FIELDS_VALID BIT(18)
+#define RX_MPDU_END_INFO1_FCS_ERR BIT(19)
+#define RX_MPDU_END_INFO1_MSDU_LEN_ERR BIT(20)
+#define RX_MPDU_END_INFO1_RXDMA0_DEST_RING GENMASK(22, 21)
+#define RX_MPDU_END_INFO1_RXDMA1_DEST_RING GENMASK(24, 23)
+#define RX_MPDU_END_INFO1_DECRYPT_STATUS_CODE GENMASK(27, 25)
+#define RX_MPDU_END_INFO1_RX_BITMAP_NOT_UPD BIT(28)
+
+struct rx_mpdu_end {
+ __le16 info0;
+ __le16 phy_ppdu_id;
+ __le32 info1;
+} __packed;
+
+/* rx_mpdu_end
+ *
+ * rxpcu_mpdu_filter_in_category
+ * Field indicates what the reason was that this mpdu frame
+ * was allowed to come into the receive path by rxpcu. Values
+ * are defined in enum %RX_DESC_RXPCU_FILTER_*.
+ *
+ * sw_frame_group_id
+ * SW processes frames based on certain classifications. Values
+ * are defined in enum %RX_DESC_SW_FRAME_GRP_ID_*.
+ *
+ * phy_ppdu_id
+ * A ppdu counter value that PHY increments for every PPDU
+ * received. The counter value wraps around.
+ *
+ * unsup_ktype_short_frame
+ * This bit will be '1' when WEP or TKIP or WAPI key type is
+ * received for 11ah short frame. Crypto will bypass the received
+ * packet without decryption to RxOLE after setting this bit.
+ *
+ * rx_in_tx_decrypt_byp
+ * Indicates that RX packet is not decrypted as Crypto is
+ * busy with TX packet processing.
+ *
+ * overflow_err
+ * RXPCU Receive FIFO ran out of space to receive the full MPDU.
+ * Therefore this MPDU is terminated early and is thus corrupted.
+ *
+ * This MPDU will not be ACKed.
+ *
+ * RXPCU might still be able to correctly receive the following
+ * MPDUs in the PPDU if enough fifo space became available in time.
+ *
+ * mpdu_length_err
+ * Set by RXPCU if the expected MPDU length does not correspond
+ * with the actually received number of bytes in the MPDU.
+ *
+ * tkip_mic_err
+ * Set by Rx crypto when crypto detected a TKIP MIC error for
+ * this MPDU.
+ *
+ * decrypt_err
+ * Set by RX CRYPTO when CRYPTO detected a decrypt error for this
+ * MPDU or CRYPTO received an encrypted frame, but did not get a
+ * valid corresponding key id in the peer entry.
+ *
+ * unencrypted_frame_err
+ * Set by RX CRYPTO when CRYPTO detected an unencrypted frame while
+ * in the peer entry field 'All_frames_shall_be_encrypted' is set.
+ *
+ * pn_fields_contain_valid_info
+ * Set by RX CRYPTO to indicate that there is a valid PN field
+ * present in this MPDU.
+ *
+ * fcs_err
+ * Set by RXPCU when there is an FCS error detected for this MPDU.
+ *
+ * msdu_length_err
+ * Set by RXOLE when there is an msdu length error detected
+ * in at least 1 of the MSDUs embedded within the MPDU.
+ *
+ * rxdma0_destination_ring
+ * rxdma1_destination_ring
+ * The ring to which RXDMA0/1 shall push the frame, assuming
+ * no MPDU level errors are detected. In case of MPDU level
+ * errors, RXDMA0/1 might change the RXDMA0/1 destination. Values
+ * are defined in %enum RX_MPDU_END_RXDMA_DEST_RING_*.
+ *
+ * decrypt_status_code
+ * Field provides insight into the decryption performed. Values
+ * are defined in enum %RX_DESC_DECRYPT_STATUS_CODE_*.
+ *
+ * rx_bitmap_not_updated
+ * Frame is received, but RXPCU could not update the receive bitmap
+ * due to (temporary) fifo constraints.
+ */
+
+/* Padding bytes to avoid TLV's spanning across 128 byte boundary */
+#define HAL_RX_DESC_PADDING0_BYTES 4
+#define HAL_RX_DESC_PADDING1_BYTES 16
+
+#define HAL_RX_DESC_HDR_STATUS_LEN 120
+
+struct hal_rx_desc {
+ __le32 msdu_end_tag;
+ struct rx_msdu_end msdu_end;
+ __le32 rx_attn_tag;
+ struct rx_attention attention;
+ __le32 msdu_start_tag;
+ struct rx_msdu_start msdu_start;
+ u8 rx_padding0[HAL_RX_DESC_PADDING0_BYTES];
+ __le32 mpdu_start_tag;
+ struct rx_mpdu_start mpdu_start;
+ __le32 mpdu_end_tag;
+ struct rx_mpdu_end mpdu_end;
+ u8 rx_padding1[HAL_RX_DESC_PADDING1_BYTES];
+ __le32 hdr_status_tag;
+ __le32 phy_ppdu_id;
+ u8 hdr_status[HAL_RX_DESC_HDR_STATUS_LEN];
+ u8 msdu_payload[0];
+} __packed;
+
+#endif /* ATH11K_RX_DESC_H */
(patches split for easier review, see the cover letter for more) Signed-off-by: Kalle Valo <kvalo@codeaurora.org> --- drivers/net/wireless/ath/ath11k/rx_desc.h | 1212 +++++++++++++++++++++++++++++ 1 file changed, 1212 insertions(+)