deleted file mode 100644
@@ -1,744 +0,0 @@
-/*
- * This file is part of wl12xx
- *
- * Copyright (c) 1998-2007 Texas Instruments Incorporated
- * Copyright (C) 2008 Nokia Corporation
- *
- * Contact: Kalle Valo <kalle.valo@nokia.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-#ifndef __REG_H__
-#define __REG_H__
-
-#include <linux/bitops.h>
-
-#define REGISTERS_BASE 0x00300000
-#define DRPW_BASE 0x00310000
-
-#define REGISTERS_DOWN_SIZE 0x00008800
-#define REGISTERS_WORK_SIZE 0x0000b000
-
-#define HW_ACCESS_ELP_CTRL_REG_ADDR 0x1FFFC
-
-/* ELP register commands */
-#define ELPCTRL_WAKE_UP 0x1
-#define ELPCTRL_WAKE_UP_WLAN_READY 0x5
-#define ELPCTRL_SLEEP 0x0
-/* ELP WLAN_READY bit */
-#define ELPCTRL_WLAN_READY 0x2
-
-/*
- * Interrupt registers.
- * 64 bit interrupt sources registers ws ced.
- * sme interupts were removed and new ones were added.
- * Order was changed.
- */
-#define FIQ_MASK (REGISTERS_BASE + 0x0400)
-#define FIQ_MASK_L (REGISTERS_BASE + 0x0400)
-#define FIQ_MASK_H (REGISTERS_BASE + 0x0404)
-#define FIQ_MASK_SET (REGISTERS_BASE + 0x0408)
-#define FIQ_MASK_SET_L (REGISTERS_BASE + 0x0408)
-#define FIQ_MASK_SET_H (REGISTERS_BASE + 0x040C)
-#define FIQ_MASK_CLR (REGISTERS_BASE + 0x0410)
-#define FIQ_MASK_CLR_L (REGISTERS_BASE + 0x0410)
-#define FIQ_MASK_CLR_H (REGISTERS_BASE + 0x0414)
-#define IRQ_MASK (REGISTERS_BASE + 0x0418)
-#define IRQ_MASK_L (REGISTERS_BASE + 0x0418)
-#define IRQ_MASK_H (REGISTERS_BASE + 0x041C)
-#define IRQ_MASK_SET (REGISTERS_BASE + 0x0420)
-#define IRQ_MASK_SET_L (REGISTERS_BASE + 0x0420)
-#define IRQ_MASK_SET_H (REGISTERS_BASE + 0x0424)
-#define IRQ_MASK_CLR (REGISTERS_BASE + 0x0428)
-#define IRQ_MASK_CLR_L (REGISTERS_BASE + 0x0428)
-#define IRQ_MASK_CLR_H (REGISTERS_BASE + 0x042C)
-#define ECPU_MASK (REGISTERS_BASE + 0x0448)
-#define FIQ_STS_L (REGISTERS_BASE + 0x044C)
-#define FIQ_STS_H (REGISTERS_BASE + 0x0450)
-#define IRQ_STS_L (REGISTERS_BASE + 0x0454)
-#define IRQ_STS_H (REGISTERS_BASE + 0x0458)
-#define INT_STS_ND (REGISTERS_BASE + 0x0464)
-#define INT_STS_RAW_L (REGISTERS_BASE + 0x0464)
-#define INT_STS_RAW_H (REGISTERS_BASE + 0x0468)
-#define INT_STS_CLR (REGISTERS_BASE + 0x04B4)
-#define INT_STS_CLR_L (REGISTERS_BASE + 0x04B4)
-#define INT_STS_CLR_H (REGISTERS_BASE + 0x04B8)
-#define INT_ACK (REGISTERS_BASE + 0x046C)
-#define INT_ACK_L (REGISTERS_BASE + 0x046C)
-#define INT_ACK_H (REGISTERS_BASE + 0x0470)
-#define INT_TRIG (REGISTERS_BASE + 0x0474)
-#define INT_TRIG_L (REGISTERS_BASE + 0x0474)
-#define INT_TRIG_H (REGISTERS_BASE + 0x0478)
-#define HOST_STS_L (REGISTERS_BASE + 0x045C)
-#define HOST_STS_H (REGISTERS_BASE + 0x0460)
-#define HOST_MASK (REGISTERS_BASE + 0x0430)
-#define HOST_MASK_L (REGISTERS_BASE + 0x0430)
-#define HOST_MASK_H (REGISTERS_BASE + 0x0434)
-#define HOST_MASK_SET (REGISTERS_BASE + 0x0438)
-#define HOST_MASK_SET_L (REGISTERS_BASE + 0x0438)
-#define HOST_MASK_SET_H (REGISTERS_BASE + 0x043C)
-#define HOST_MASK_CLR (REGISTERS_BASE + 0x0440)
-#define HOST_MASK_CLR_L (REGISTERS_BASE + 0x0440)
-#define HOST_MASK_CLR_H (REGISTERS_BASE + 0x0444)
-
-/* Host Interrupts*/
-#define HINT_MASK (REGISTERS_BASE + 0x0494)
-#define HINT_MASK_SET (REGISTERS_BASE + 0x0498)
-#define HINT_MASK_CLR (REGISTERS_BASE + 0x049C)
-#define HINT_STS_ND_MASKED (REGISTERS_BASE + 0x04A0)
-/*1150 spec calls this HINT_STS_RAW*/
-#define HINT_STS_ND (REGISTERS_BASE + 0x04B0)
-#define HINT_STS_CLR (REGISTERS_BASE + 0x04A4)
-#define HINT_ACK (REGISTERS_BASE + 0x04A8)
-#define HINT_TRIG (REGISTERS_BASE + 0x04AC)
-
-/* Device Configuration registers*/
-#define SOR_CFG (REGISTERS_BASE + 0x0800)
-#define ECPU_CTRL (REGISTERS_BASE + 0x0804)
-#define HI_CFG (REGISTERS_BASE + 0x0808)
-#define EE_START (REGISTERS_BASE + 0x080C)
-
-#define CHIP_ID_B (REGISTERS_BASE + 0x5674)
-
-#define CHIP_ID_1251_PG10 (0x7010101)
-#define CHIP_ID_1251_PG11 (0x7020101)
-#define CHIP_ID_1251_PG12 (0x7030101)
-
-#define ENABLE (REGISTERS_BASE + 0x5450)
-
-/* Power Management registers */
-#define ELP_CFG_MODE (REGISTERS_BASE + 0x5804)
-#define ELP_CMD (REGISTERS_BASE + 0x5808)
-#define PLL_CAL_TIME (REGISTERS_BASE + 0x5810)
-#define CLK_REQ_TIME (REGISTERS_BASE + 0x5814)
-#define CLK_BUF_TIME (REGISTERS_BASE + 0x5818)
-
-#define CFG_PLL_SYNC_CNT (REGISTERS_BASE + 0x5820)
-
-/* Scratch Pad registers*/
-#define SCR_PAD0 (REGISTERS_BASE + 0x5608)
-#define SCR_PAD1 (REGISTERS_BASE + 0x560C)
-#define SCR_PAD2 (REGISTERS_BASE + 0x5610)
-#define SCR_PAD3 (REGISTERS_BASE + 0x5614)
-#define SCR_PAD4 (REGISTERS_BASE + 0x5618)
-#define SCR_PAD4_SET (REGISTERS_BASE + 0x561C)
-#define SCR_PAD4_CLR (REGISTERS_BASE + 0x5620)
-#define SCR_PAD5 (REGISTERS_BASE + 0x5624)
-#define SCR_PAD5_SET (REGISTERS_BASE + 0x5628)
-#define SCR_PAD5_CLR (REGISTERS_BASE + 0x562C)
-#define SCR_PAD6 (REGISTERS_BASE + 0x5630)
-#define SCR_PAD7 (REGISTERS_BASE + 0x5634)
-#define SCR_PAD8 (REGISTERS_BASE + 0x5638)
-#define SCR_PAD9 (REGISTERS_BASE + 0x563C)
-
-/* Spare registers*/
-#define SPARE_A1 (REGISTERS_BASE + 0x0994)
-#define SPARE_A2 (REGISTERS_BASE + 0x0998)
-#define SPARE_A3 (REGISTERS_BASE + 0x099C)
-#define SPARE_A4 (REGISTERS_BASE + 0x09A0)
-#define SPARE_A5 (REGISTERS_BASE + 0x09A4)
-#define SPARE_A6 (REGISTERS_BASE + 0x09A8)
-#define SPARE_A7 (REGISTERS_BASE + 0x09AC)
-#define SPARE_A8 (REGISTERS_BASE + 0x09B0)
-#define SPARE_B1 (REGISTERS_BASE + 0x5420)
-#define SPARE_B2 (REGISTERS_BASE + 0x5424)
-#define SPARE_B3 (REGISTERS_BASE + 0x5428)
-#define SPARE_B4 (REGISTERS_BASE + 0x542C)
-#define SPARE_B5 (REGISTERS_BASE + 0x5430)
-#define SPARE_B6 (REGISTERS_BASE + 0x5434)
-#define SPARE_B7 (REGISTERS_BASE + 0x5438)
-#define SPARE_B8 (REGISTERS_BASE + 0x543C)
-
-enum wl12xx_acx_int_reg {
- ACX_REG_INTERRUPT_TRIG,
- ACX_REG_INTERRUPT_TRIG_H,
-
-/*=============================================
- Host Interrupt Mask Register - 32bit (RW)
- ------------------------------------------
- Setting a bit in this register masks the
- corresponding interrupt to the host.
- 0 - RX0 - Rx first dubble buffer Data Interrupt
- 1 - TXD - Tx Data Interrupt
- 2 - TXXFR - Tx Transfer Interrupt
- 3 - RX1 - Rx second dubble buffer Data Interrupt
- 4 - RXXFR - Rx Transfer Interrupt
- 5 - EVENT_A - Event Mailbox interrupt
- 6 - EVENT_B - Event Mailbox interrupt
- 7 - WNONHST - Wake On Host Interrupt
- 8 - TRACE_A - Debug Trace interrupt
- 9 - TRACE_B - Debug Trace interrupt
- 10 - CDCMP - Command Complete Interrupt
- 11 -
- 12 -
- 13 -
- 14 - ICOMP - Initialization Complete Interrupt
- 16 - SG SE - Soft Gemini - Sense enable interrupt
- 17 - SG SD - Soft Gemini - Sense disable interrupt
- 18 - -
- 19 - -
- 20 - -
- 21- -
- Default: 0x0001
-*==============================================*/
- ACX_REG_INTERRUPT_MASK,
-
-/*=============================================
- Host Interrupt Mask Set 16bit, (Write only)
- ------------------------------------------
- Setting a bit in this register sets
- the corresponding bin in ACX_HINT_MASK register
- without effecting the mask
- state of other bits (0 = no effect).
-==============================================*/
- ACX_REG_HINT_MASK_SET,
-
-/*=============================================
- Host Interrupt Mask Clear 16bit,(Write only)
- ------------------------------------------
- Setting a bit in this register clears
- the corresponding bin in ACX_HINT_MASK register
- without effecting the mask
- state of other bits (0 = no effect).
-=============================================*/
- ACX_REG_HINT_MASK_CLR,
-
-/*=============================================
- Host Interrupt Status Nondestructive Read
- 16bit,(Read only)
- ------------------------------------------
- The host can read this register to determine
- which interrupts are active.
- Reading this register doesn't
- effect its content.
-=============================================*/
- ACX_REG_INTERRUPT_NO_CLEAR,
-
-/*=============================================
- Host Interrupt Status Clear on Read Register
- 16bit,(Read only)
- ------------------------------------------
- The host can read this register to determine
- which interrupts are active.
- Reading this register clears it,
- thus making all interrupts inactive.
-==============================================*/
- ACX_REG_INTERRUPT_CLEAR,
-
-/*=============================================
- Host Interrupt Acknowledge Register
- 16bit,(Write only)
- ------------------------------------------
- The host can set individual bits in this
- register to clear (acknowledge) the corresp.
- interrupt status bits in the HINT_STS_CLR and
- HINT_STS_ND registers, thus making the
- assotiated interrupt inactive. (0-no effect)
-==============================================*/
- ACX_REG_INTERRUPT_ACK,
-
-/*===============================================
- Host Software Reset - 32bit RW
- ------------------------------------------
- [31:1] Reserved
- 0 SOFT_RESET Soft Reset - When this bit is set,
- it holds the Wlan hardware in a soft reset state.
- This reset disables all MAC and baseband processor
- clocks except the CardBus/PCI interface clock.
- It also initializes all MAC state machines except
- the host interface. It does not reload the
- contents of the EEPROM. When this bit is cleared
- (not self-clearing), the Wlan hardware
- exits the software reset state.
-===============================================*/
- ACX_REG_SLV_SOFT_RESET,
-
-/*===============================================
- EEPROM Burst Read Start - 32bit RW
- ------------------------------------------
- [31:1] Reserved
- 0 ACX_EE_START - EEPROM Burst Read Start 0
- Setting this bit starts a burst read from
- the external EEPROM.
- If this bit is set (after reset) before an EEPROM read/write,
- the burst read starts at EEPROM address 0.
- Otherwise, it starts at the address
- following the address of the previous access.
- TheWlan hardware hardware clears this bit automatically.
-
- Default: 0x00000000
-*================================================*/
- ACX_REG_EE_START,
-
-/* Embedded ARM CPU Control */
-
-/*===============================================
- Halt eCPU - 32bit RW
- ------------------------------------------
- 0 HALT_ECPU Halt Embedded CPU - This bit is the
- compliment of bit 1 (MDATA2) in the SOR_CFG register.
- During a hardware reset, this bit holds
- the inverse of MDATA2.
- When downloading firmware from the host,
- set this bit (pull down MDATA2).
- The host clears this bit after downloading the firmware into
- zero-wait-state SSRAM.
- When loading firmware from Flash, clear this bit (pull up MDATA2)
- so that the eCPU can run the bootloader code in Flash
- HALT_ECPU eCPU State
- --------------------
- 1 halt eCPU
- 0 enable eCPU
- ===============================================*/
- ACX_REG_ECPU_CONTROL,
-
- ACX_REG_TABLE_LEN
-};
-
-#define ACX_SLV_SOFT_RESET_BIT BIT(1)
-#define ACX_REG_EEPROM_START_BIT BIT(1)
-
-/* Command/Information Mailbox Pointers */
-
-/*===============================================
- Command Mailbox Pointer - 32bit RW
- ------------------------------------------
- This register holds the start address of
- the command mailbox located in the Wlan hardware memory.
- The host must read this pointer after a reset to
- find the location of the command mailbox.
- The Wlan hardware initializes the command mailbox
- pointer with the default address of the command mailbox.
- The command mailbox pointer is not valid until after
- the host receives the Init Complete interrupt from
- the Wlan hardware.
- ===============================================*/
-#define REG_COMMAND_MAILBOX_PTR (SCR_PAD0)
-
-/*===============================================
- Information Mailbox Pointer - 32bit RW
- ------------------------------------------
- This register holds the start address of
- the information mailbox located in the Wlan hardware memory.
- The host must read this pointer after a reset to find
- the location of the information mailbox.
- The Wlan hardware initializes the information mailbox pointer
- with the default address of the information mailbox.
- The information mailbox pointer is not valid
- until after the host receives the Init Complete interrupt from
- the Wlan hardware.
- ===============================================*/
-#define REG_EVENT_MAILBOX_PTR (SCR_PAD1)
-
-
-/* Misc */
-
-#define REG_ENABLE_TX_RX (ENABLE)
-/*
- * Rx configuration (filter) information element
- * ---------------------------------------------
- */
-#define REG_RX_CONFIG (RX_CFG)
-#define REG_RX_FILTER (RX_FILTER_CFG)
-
-
-#define RX_CFG_ENABLE_PHY_HEADER_PLCP 0x0002
-
-/* promiscuous - receives all valid frames */
-#define RX_CFG_PROMISCUOUS 0x0008
-
-/* receives frames from any BSSID */
-#define RX_CFG_BSSID 0x0020
-
-/* receives frames destined to any MAC address */
-#define RX_CFG_MAC 0x0010
-
-#define RX_CFG_ENABLE_ONLY_MY_DEST_MAC 0x0010
-#define RX_CFG_ENABLE_ANY_DEST_MAC 0x0000
-#define RX_CFG_ENABLE_ONLY_MY_BSSID 0x0020
-#define RX_CFG_ENABLE_ANY_BSSID 0x0000
-
-/* discards all broadcast frames */
-#define RX_CFG_DISABLE_BCAST 0x0200
-
-#define RX_CFG_ENABLE_ONLY_MY_SSID 0x0400
-#define RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR 0x0800
-#define RX_CFG_COPY_RX_STATUS 0x2000
-#define RX_CFG_TSF 0x10000
-
-#define RX_CONFIG_OPTION_ANY_DST_MY_BSS (RX_CFG_ENABLE_ANY_DEST_MAC | \
- RX_CFG_ENABLE_ONLY_MY_BSSID)
-
-#define RX_CONFIG_OPTION_MY_DST_ANY_BSS (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\
- | RX_CFG_ENABLE_ANY_BSSID)
-
-#define RX_CONFIG_OPTION_ANY_DST_ANY_BSS (RX_CFG_ENABLE_ANY_DEST_MAC | \
- RX_CFG_ENABLE_ANY_BSSID)
-
-#define RX_CONFIG_OPTION_MY_DST_MY_BSS (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\
- | RX_CFG_ENABLE_ONLY_MY_BSSID)
-
-#define RX_CONFIG_OPTION_FOR_SCAN (RX_CFG_ENABLE_PHY_HEADER_PLCP \
- | RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR \
- | RX_CFG_COPY_RX_STATUS | RX_CFG_TSF)
-
-#define RX_CONFIG_OPTION_FOR_MEASUREMENT (RX_CFG_ENABLE_ANY_DEST_MAC)
-
-#define RX_CONFIG_OPTION_FOR_JOIN (RX_CFG_ENABLE_ONLY_MY_BSSID | \
- RX_CFG_ENABLE_ONLY_MY_DEST_MAC)
-
-#define RX_CONFIG_OPTION_FOR_IBSS_JOIN (RX_CFG_ENABLE_ONLY_MY_SSID | \
- RX_CFG_ENABLE_ONLY_MY_DEST_MAC)
-
-#define RX_FILTER_OPTION_DEF (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\
- | CFG_RX_CTL_EN | CFG_RX_BCN_EN\
- | CFG_RX_AUTH_EN | CFG_RX_ASSOC_EN)
-
-#define RX_FILTER_OPTION_FILTER_ALL 0
-
-#define RX_FILTER_OPTION_DEF_PRSP_BCN (CFG_RX_PRSP_EN | CFG_RX_MGMT_EN\
- | CFG_RX_RCTS_ACK | CFG_RX_BCN_EN)
-
-#define RX_FILTER_OPTION_JOIN (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\
- | CFG_RX_BCN_EN | CFG_RX_AUTH_EN\
- | CFG_RX_ASSOC_EN | CFG_RX_RCTS_ACK\
- | CFG_RX_PRSP_EN)
-
-
-/*===============================================
- Phy regs
- ===============================================*/
-#define ACX_PHY_ADDR_REG SBB_ADDR
-#define ACX_PHY_DATA_REG SBB_DATA
-#define ACX_PHY_CTRL_REG SBB_CTL
-#define ACX_PHY_REG_WR_MASK 0x00000001ul
-#define ACX_PHY_REG_RD_MASK 0x00000002ul
-
-
-/*===============================================
- EEPROM Read/Write Request 32bit RW
- ------------------------------------------
- 1 EE_READ - EEPROM Read Request 1 - Setting this bit
- loads a single byte of data into the EE_DATA
- register from the EEPROM location specified in
- the EE_ADDR register.
- The Wlan hardware hardware clears this bit automatically.
- EE_DATA is valid when this bit is cleared.
-
- 0 EE_WRITE - EEPROM Write Request - Setting this bit
- writes a single byte of data from the EE_DATA register into the
- EEPROM location specified in the EE_ADDR register.
- The Wlan hardware hardware clears this bit automatically.
-*===============================================*/
-#define ACX_EE_CTL_REG EE_CTL
-#define EE_WRITE 0x00000001ul
-#define EE_READ 0x00000002ul
-
-/*===============================================
- EEPROM Address - 32bit RW
- ------------------------------------------
- This register specifies the address
- within the EEPROM from/to which to read/write data.
- ===============================================*/
-#define ACX_EE_ADDR_REG EE_ADDR
-
-/*===============================================
- EEPROM Data - 32bit RW
- ------------------------------------------
- This register either holds the read 8 bits of
- data from the EEPROM or the write data
- to be written to the EEPROM.
- ===============================================*/
-#define ACX_EE_DATA_REG EE_DATA
-
-/*===============================================
- EEPROM Base Address - 32bit RW
- ------------------------------------------
- This register holds the upper nine bits
- [23:15] of the 24-bit Wlan hardware memory
- address for burst reads from EEPROM accesses.
- The EEPROM provides the lower 15 bits of this address.
- The MSB of the address from the EEPROM is ignored.
- ===============================================*/
-#define ACX_EE_CFG EE_CFG
-
-/*===============================================
- GPIO Output Values -32bit, RW
- ------------------------------------------
- [31:16] Reserved
- [15: 0] Specify the output values (at the output driver inputs) for
- GPIO[15:0], respectively.
- ===============================================*/
-#define ACX_GPIO_OUT_REG GPIO_OUT
-#define ACX_MAX_GPIO_LINES 15
-
-/*===============================================
- Contention window -32bit, RW
- ------------------------------------------
- [31:26] Reserved
- [25:16] Max (0x3ff)
- [15:07] Reserved
- [06:00] Current contention window value - default is 0x1F
- ===============================================*/
-#define ACX_CONT_WIND_CFG_REG CONT_WIND_CFG
-#define ACX_CONT_WIND_MIN_MASK 0x0000007f
-#define ACX_CONT_WIND_MAX 0x03ff0000
-
-/*
- * Indirect slave register/memory registers
- * ----------------------------------------
- */
-#define HW_SLAVE_REG_ADDR_REG 0x00000004
-#define HW_SLAVE_REG_DATA_REG 0x00000008
-#define HW_SLAVE_REG_CTRL_REG 0x0000000c
-
-#define SLAVE_AUTO_INC 0x00010000
-#define SLAVE_NO_AUTO_INC 0x00000000
-#define SLAVE_HOST_LITTLE_ENDIAN 0x00000000
-
-#define HW_SLAVE_MEM_ADDR_REG SLV_MEM_ADDR
-#define HW_SLAVE_MEM_DATA_REG SLV_MEM_DATA
-#define HW_SLAVE_MEM_CTRL_REG SLV_MEM_CTL
-#define HW_SLAVE_MEM_ENDIAN_REG SLV_END_CTL
-
-#define HW_FUNC_EVENT_INT_EN 0x8000
-#define HW_FUNC_EVENT_MASK_REG 0x00000034
-
-#define ACX_MAC_TIMESTAMP_REG (MAC_TIMESTAMP)
-
-/*===============================================
- HI_CFG Interface Configuration Register Values
- ------------------------------------------
- ===============================================*/
-#define HI_CFG_UART_ENABLE 0x00000004
-#define HI_CFG_RST232_ENABLE 0x00000008
-#define HI_CFG_CLOCK_REQ_SELECT 0x00000010
-#define HI_CFG_HOST_INT_ENABLE 0x00000020
-#define HI_CFG_VLYNQ_OUTPUT_ENABLE 0x00000040
-#define HI_CFG_HOST_INT_ACTIVE_LOW 0x00000080
-#define HI_CFG_UART_TX_OUT_GPIO_15 0x00000100
-#define HI_CFG_UART_TX_OUT_GPIO_14 0x00000200
-#define HI_CFG_UART_TX_OUT_GPIO_7 0x00000400
-
-/*
- * NOTE: USE_ACTIVE_HIGH compilation flag should be defined in makefile
- * for platforms using active high interrupt level
- */
-#ifdef USE_ACTIVE_HIGH
-#define HI_CFG_DEF_VAL \
- (HI_CFG_UART_ENABLE | \
- HI_CFG_RST232_ENABLE | \
- HI_CFG_CLOCK_REQ_SELECT | \
- HI_CFG_HOST_INT_ENABLE)
-#else
-#define HI_CFG_DEF_VAL \
- (HI_CFG_UART_ENABLE | \
- HI_CFG_RST232_ENABLE | \
- HI_CFG_CLOCK_REQ_SELECT | \
- HI_CFG_HOST_INT_ENABLE)
-
-#endif
-
-#define REF_FREQ_19_2 0
-#define REF_FREQ_26_0 1
-#define REF_FREQ_38_4 2
-#define REF_FREQ_40_0 3
-#define REF_FREQ_33_6 4
-#define REF_FREQ_NUM 5
-
-#define LUT_PARAM_INTEGER_DIVIDER 0
-#define LUT_PARAM_FRACTIONAL_DIVIDER 1
-#define LUT_PARAM_ATTN_BB 2
-#define LUT_PARAM_ALPHA_BB 3
-#define LUT_PARAM_STOP_TIME_BB 4
-#define LUT_PARAM_BB_PLL_LOOP_FILTER 5
-#define LUT_PARAM_NUM 6
-
-#define ACX_EEPROMLESS_IND_REG (SCR_PAD4)
-#define USE_EEPROM 0
-#define SOFT_RESET_MAX_TIME 1000000
-#define SOFT_RESET_STALL_TIME 1000
-#define NVS_DATA_BUNDARY_ALIGNMENT 4
-
-
-/* Firmware image load chunk size */
-#define CHUNK_SIZE 512
-
-/* Firmware image header size */
-#define FW_HDR_SIZE 8
-
-#define ECPU_CONTROL_HALT 0x00000101
-
-
-/******************************************************************************
-
- CHANNELS, BAND & REG DOMAINS definitions
-
-******************************************************************************/
-
-
-enum {
- RADIO_BAND_2_4GHZ = 0, /* 2.4 Ghz band */
- RADIO_BAND_5GHZ = 1, /* 5 Ghz band */
- RADIO_BAND_JAPAN_4_9_GHZ = 2,
- DEFAULT_BAND = RADIO_BAND_2_4GHZ,
- INVALID_BAND = 0xFE,
- MAX_RADIO_BANDS = 0xFF
-};
-
-enum {
- NO_RATE = 0,
- RATE_1MBPS = 0x0A,
- RATE_2MBPS = 0x14,
- RATE_5_5MBPS = 0x37,
- RATE_6MBPS = 0x0B,
- RATE_9MBPS = 0x0F,
- RATE_11MBPS = 0x6E,
- RATE_12MBPS = 0x0A,
- RATE_18MBPS = 0x0E,
- RATE_22MBPS = 0xDC,
- RATE_24MBPS = 0x09,
- RATE_36MBPS = 0x0D,
- RATE_48MBPS = 0x08,
- RATE_54MBPS = 0x0C
-};
-
-enum {
- RATE_INDEX_1MBPS = 0,
- RATE_INDEX_2MBPS = 1,
- RATE_INDEX_5_5MBPS = 2,
- RATE_INDEX_6MBPS = 3,
- RATE_INDEX_9MBPS = 4,
- RATE_INDEX_11MBPS = 5,
- RATE_INDEX_12MBPS = 6,
- RATE_INDEX_18MBPS = 7,
- RATE_INDEX_22MBPS = 8,
- RATE_INDEX_24MBPS = 9,
- RATE_INDEX_36MBPS = 10,
- RATE_INDEX_48MBPS = 11,
- RATE_INDEX_54MBPS = 12,
- RATE_INDEX_MAX = RATE_INDEX_54MBPS,
- MAX_RATE_INDEX,
- INVALID_RATE_INDEX = MAX_RATE_INDEX,
- RATE_INDEX_ENUM_MAX_SIZE = 0x7FFFFFFF
-};
-
-enum {
- RATE_MASK_1MBPS = 0x1,
- RATE_MASK_2MBPS = 0x2,
- RATE_MASK_5_5MBPS = 0x4,
- RATE_MASK_11MBPS = 0x20,
-};
-
-#define SHORT_PREAMBLE_BIT BIT(0) /* CCK or Barker depending on the rate */
-#define OFDM_RATE_BIT BIT(6)
-#define PBCC_RATE_BIT BIT(7)
-
-enum {
- CCK_LONG = 0,
- CCK_SHORT = SHORT_PREAMBLE_BIT,
- PBCC_LONG = PBCC_RATE_BIT,
- PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT,
- OFDM = OFDM_RATE_BIT
-};
-
-/******************************************************************************
-
-Transmit-Descriptor RATE-SET field definitions...
-
-Define a new "Rate-Set" for TX path that incorporates the
-Rate & Modulation info into a single 16-bit field.
-
-TxdRateSet_t:
-b15 - Indicates Preamble type (1=SHORT, 0=LONG).
- Notes:
- Must be LONG (0) for 1Mbps rate.
- Does not apply (set to 0) for RevG-OFDM rates.
-b14 - Indicates PBCC encoding (1=PBCC, 0=not).
- Notes:
- Does not apply (set to 0) for rates 1 and 2 Mbps.
- Does not apply (set to 0) for RevG-OFDM rates.
-b13 - Unused (set to 0).
-b12-b0 - Supported Rate indicator bits as defined below.
-
-******************************************************************************/
-
-
-#define TNETW1251_CHIP_ID_PG1_0 0x07010101
-#define TNETW1251_CHIP_ID_PG1_1 0x07020101
-#define TNETW1251_CHIP_ID_PG1_2 0x07030101
-
-/*************************************************************************
-
- Interrupt Trigger Register (Host -> WiLink)
-
-**************************************************************************/
-
-/* Hardware to Embedded CPU Interrupts - first 32-bit register set */
-
-/*
- * Host Command Interrupt. Setting this bit masks
- * the interrupt that the host issues to inform
- * the FW that it has sent a command
- * to the Wlan hardware Command Mailbox.
- */
-#define INTR_TRIG_CMD BIT(0)
-
-/*
- * Host Event Acknowlegde Interrupt. The host
- * sets this bit to acknowledge that it received
- * the unsolicited information from the event
- * mailbox.
- */
-#define INTR_TRIG_EVENT_ACK BIT(1)
-
-/*
- * The host sets this bit to inform the Wlan
- * FW that a TX packet is in the XFER
- * Buffer #0.
- */
-#define INTR_TRIG_TX_PROC0 BIT(2)
-
-/*
- * The host sets this bit to inform the FW
- * that it read a packet from RX XFER
- * Buffer #0.
- */
-#define INTR_TRIG_RX_PROC0 BIT(3)
-
-#define INTR_TRIG_DEBUG_ACK BIT(4)
-
-#define INTR_TRIG_STATE_CHANGED BIT(5)
-
-
-/* Hardware to Embedded CPU Interrupts - second 32-bit register set */
-
-/*
- * The host sets this bit to inform the FW
- * that it read a packet from RX XFER
- * Buffer #1.
- */
-#define INTR_TRIG_RX_PROC1 BIT(17)
-
-/*
- * The host sets this bit to inform the Wlan
- * hardware that a TX packet is in the XFER
- * Buffer #1.
- */
-#define INTR_TRIG_TX_PROC1 BIT(18)
-
-#endif
@@ -4,7 +4,7 @@
#include <linux/crc7.h>
#include "wl1251.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_cmd.h"
#include "wl1251_ps.h"
@@ -23,7 +23,7 @@
#include <linux/gpio.h>
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_boot.h"
#include "wl1251_io.h"
#include "wl1251_spi.h"
@@ -4,7 +4,7 @@
#include <linux/crc7.h>
#include "wl1251.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_io.h"
#include "wl1251_ps.h"
#include "wl1251_acx.h"
@@ -23,7 +23,7 @@
*/
#include "wl1251.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_io.h"
#include "wl1251_event.h"
#include "wl1251_ps.h"
@@ -28,7 +28,7 @@
#include "wl12xx_80211.h"
#include "wl1251_acx.h"
#include "wl1251_cmd.h"
-#include "reg.h"
+#include "wl1251_reg.h"
int wl1251_hw_init_hwenc_config(struct wl1251 *wl)
{
@@ -22,7 +22,7 @@
*/
#include "wl1251.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_io.h"
/* FIXME: this is static data nowadays and the table can be removed */
@@ -31,7 +31,7 @@
#include "wl1251.h"
#include "wl12xx_80211.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_io.h"
#include "wl1251_cmd.h"
#include "wl1251_event.h"
@@ -21,7 +21,7 @@
*
*/
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_ps.h"
#include "wl1251_cmd.h"
#include "wl1251_io.h"
new file mode 100644
@@ -0,0 +1,744 @@
+/*
+ * This file is part of wl12xx
+ *
+ * Copyright (c) 1998-2007 Texas Instruments Incorporated
+ * Copyright (C) 2008 Nokia Corporation
+ *
+ * Contact: Kalle Valo <kalle.valo@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __REG_H__
+#define __REG_H__
+
+#include <linux/bitops.h>
+
+#define REGISTERS_BASE 0x00300000
+#define DRPW_BASE 0x00310000
+
+#define REGISTERS_DOWN_SIZE 0x00008800
+#define REGISTERS_WORK_SIZE 0x0000b000
+
+#define HW_ACCESS_ELP_CTRL_REG_ADDR 0x1FFFC
+
+/* ELP register commands */
+#define ELPCTRL_WAKE_UP 0x1
+#define ELPCTRL_WAKE_UP_WLAN_READY 0x5
+#define ELPCTRL_SLEEP 0x0
+/* ELP WLAN_READY bit */
+#define ELPCTRL_WLAN_READY 0x2
+
+/*
+ * Interrupt registers.
+ * 64 bit interrupt sources registers ws ced.
+ * sme interupts were removed and new ones were added.
+ * Order was changed.
+ */
+#define FIQ_MASK (REGISTERS_BASE + 0x0400)
+#define FIQ_MASK_L (REGISTERS_BASE + 0x0400)
+#define FIQ_MASK_H (REGISTERS_BASE + 0x0404)
+#define FIQ_MASK_SET (REGISTERS_BASE + 0x0408)
+#define FIQ_MASK_SET_L (REGISTERS_BASE + 0x0408)
+#define FIQ_MASK_SET_H (REGISTERS_BASE + 0x040C)
+#define FIQ_MASK_CLR (REGISTERS_BASE + 0x0410)
+#define FIQ_MASK_CLR_L (REGISTERS_BASE + 0x0410)
+#define FIQ_MASK_CLR_H (REGISTERS_BASE + 0x0414)
+#define IRQ_MASK (REGISTERS_BASE + 0x0418)
+#define IRQ_MASK_L (REGISTERS_BASE + 0x0418)
+#define IRQ_MASK_H (REGISTERS_BASE + 0x041C)
+#define IRQ_MASK_SET (REGISTERS_BASE + 0x0420)
+#define IRQ_MASK_SET_L (REGISTERS_BASE + 0x0420)
+#define IRQ_MASK_SET_H (REGISTERS_BASE + 0x0424)
+#define IRQ_MASK_CLR (REGISTERS_BASE + 0x0428)
+#define IRQ_MASK_CLR_L (REGISTERS_BASE + 0x0428)
+#define IRQ_MASK_CLR_H (REGISTERS_BASE + 0x042C)
+#define ECPU_MASK (REGISTERS_BASE + 0x0448)
+#define FIQ_STS_L (REGISTERS_BASE + 0x044C)
+#define FIQ_STS_H (REGISTERS_BASE + 0x0450)
+#define IRQ_STS_L (REGISTERS_BASE + 0x0454)
+#define IRQ_STS_H (REGISTERS_BASE + 0x0458)
+#define INT_STS_ND (REGISTERS_BASE + 0x0464)
+#define INT_STS_RAW_L (REGISTERS_BASE + 0x0464)
+#define INT_STS_RAW_H (REGISTERS_BASE + 0x0468)
+#define INT_STS_CLR (REGISTERS_BASE + 0x04B4)
+#define INT_STS_CLR_L (REGISTERS_BASE + 0x04B4)
+#define INT_STS_CLR_H (REGISTERS_BASE + 0x04B8)
+#define INT_ACK (REGISTERS_BASE + 0x046C)
+#define INT_ACK_L (REGISTERS_BASE + 0x046C)
+#define INT_ACK_H (REGISTERS_BASE + 0x0470)
+#define INT_TRIG (REGISTERS_BASE + 0x0474)
+#define INT_TRIG_L (REGISTERS_BASE + 0x0474)
+#define INT_TRIG_H (REGISTERS_BASE + 0x0478)
+#define HOST_STS_L (REGISTERS_BASE + 0x045C)
+#define HOST_STS_H (REGISTERS_BASE + 0x0460)
+#define HOST_MASK (REGISTERS_BASE + 0x0430)
+#define HOST_MASK_L (REGISTERS_BASE + 0x0430)
+#define HOST_MASK_H (REGISTERS_BASE + 0x0434)
+#define HOST_MASK_SET (REGISTERS_BASE + 0x0438)
+#define HOST_MASK_SET_L (REGISTERS_BASE + 0x0438)
+#define HOST_MASK_SET_H (REGISTERS_BASE + 0x043C)
+#define HOST_MASK_CLR (REGISTERS_BASE + 0x0440)
+#define HOST_MASK_CLR_L (REGISTERS_BASE + 0x0440)
+#define HOST_MASK_CLR_H (REGISTERS_BASE + 0x0444)
+
+/* Host Interrupts*/
+#define HINT_MASK (REGISTERS_BASE + 0x0494)
+#define HINT_MASK_SET (REGISTERS_BASE + 0x0498)
+#define HINT_MASK_CLR (REGISTERS_BASE + 0x049C)
+#define HINT_STS_ND_MASKED (REGISTERS_BASE + 0x04A0)
+/*1150 spec calls this HINT_STS_RAW*/
+#define HINT_STS_ND (REGISTERS_BASE + 0x04B0)
+#define HINT_STS_CLR (REGISTERS_BASE + 0x04A4)
+#define HINT_ACK (REGISTERS_BASE + 0x04A8)
+#define HINT_TRIG (REGISTERS_BASE + 0x04AC)
+
+/* Device Configuration registers*/
+#define SOR_CFG (REGISTERS_BASE + 0x0800)
+#define ECPU_CTRL (REGISTERS_BASE + 0x0804)
+#define HI_CFG (REGISTERS_BASE + 0x0808)
+#define EE_START (REGISTERS_BASE + 0x080C)
+
+#define CHIP_ID_B (REGISTERS_BASE + 0x5674)
+
+#define CHIP_ID_1251_PG10 (0x7010101)
+#define CHIP_ID_1251_PG11 (0x7020101)
+#define CHIP_ID_1251_PG12 (0x7030101)
+
+#define ENABLE (REGISTERS_BASE + 0x5450)
+
+/* Power Management registers */
+#define ELP_CFG_MODE (REGISTERS_BASE + 0x5804)
+#define ELP_CMD (REGISTERS_BASE + 0x5808)
+#define PLL_CAL_TIME (REGISTERS_BASE + 0x5810)
+#define CLK_REQ_TIME (REGISTERS_BASE + 0x5814)
+#define CLK_BUF_TIME (REGISTERS_BASE + 0x5818)
+
+#define CFG_PLL_SYNC_CNT (REGISTERS_BASE + 0x5820)
+
+/* Scratch Pad registers*/
+#define SCR_PAD0 (REGISTERS_BASE + 0x5608)
+#define SCR_PAD1 (REGISTERS_BASE + 0x560C)
+#define SCR_PAD2 (REGISTERS_BASE + 0x5610)
+#define SCR_PAD3 (REGISTERS_BASE + 0x5614)
+#define SCR_PAD4 (REGISTERS_BASE + 0x5618)
+#define SCR_PAD4_SET (REGISTERS_BASE + 0x561C)
+#define SCR_PAD4_CLR (REGISTERS_BASE + 0x5620)
+#define SCR_PAD5 (REGISTERS_BASE + 0x5624)
+#define SCR_PAD5_SET (REGISTERS_BASE + 0x5628)
+#define SCR_PAD5_CLR (REGISTERS_BASE + 0x562C)
+#define SCR_PAD6 (REGISTERS_BASE + 0x5630)
+#define SCR_PAD7 (REGISTERS_BASE + 0x5634)
+#define SCR_PAD8 (REGISTERS_BASE + 0x5638)
+#define SCR_PAD9 (REGISTERS_BASE + 0x563C)
+
+/* Spare registers*/
+#define SPARE_A1 (REGISTERS_BASE + 0x0994)
+#define SPARE_A2 (REGISTERS_BASE + 0x0998)
+#define SPARE_A3 (REGISTERS_BASE + 0x099C)
+#define SPARE_A4 (REGISTERS_BASE + 0x09A0)
+#define SPARE_A5 (REGISTERS_BASE + 0x09A4)
+#define SPARE_A6 (REGISTERS_BASE + 0x09A8)
+#define SPARE_A7 (REGISTERS_BASE + 0x09AC)
+#define SPARE_A8 (REGISTERS_BASE + 0x09B0)
+#define SPARE_B1 (REGISTERS_BASE + 0x5420)
+#define SPARE_B2 (REGISTERS_BASE + 0x5424)
+#define SPARE_B3 (REGISTERS_BASE + 0x5428)
+#define SPARE_B4 (REGISTERS_BASE + 0x542C)
+#define SPARE_B5 (REGISTERS_BASE + 0x5430)
+#define SPARE_B6 (REGISTERS_BASE + 0x5434)
+#define SPARE_B7 (REGISTERS_BASE + 0x5438)
+#define SPARE_B8 (REGISTERS_BASE + 0x543C)
+
+enum wl12xx_acx_int_reg {
+ ACX_REG_INTERRUPT_TRIG,
+ ACX_REG_INTERRUPT_TRIG_H,
+
+/*=============================================
+ Host Interrupt Mask Register - 32bit (RW)
+ ------------------------------------------
+ Setting a bit in this register masks the
+ corresponding interrupt to the host.
+ 0 - RX0 - Rx first dubble buffer Data Interrupt
+ 1 - TXD - Tx Data Interrupt
+ 2 - TXXFR - Tx Transfer Interrupt
+ 3 - RX1 - Rx second dubble buffer Data Interrupt
+ 4 - RXXFR - Rx Transfer Interrupt
+ 5 - EVENT_A - Event Mailbox interrupt
+ 6 - EVENT_B - Event Mailbox interrupt
+ 7 - WNONHST - Wake On Host Interrupt
+ 8 - TRACE_A - Debug Trace interrupt
+ 9 - TRACE_B - Debug Trace interrupt
+ 10 - CDCMP - Command Complete Interrupt
+ 11 -
+ 12 -
+ 13 -
+ 14 - ICOMP - Initialization Complete Interrupt
+ 16 - SG SE - Soft Gemini - Sense enable interrupt
+ 17 - SG SD - Soft Gemini - Sense disable interrupt
+ 18 - -
+ 19 - -
+ 20 - -
+ 21- -
+ Default: 0x0001
+*==============================================*/
+ ACX_REG_INTERRUPT_MASK,
+
+/*=============================================
+ Host Interrupt Mask Set 16bit, (Write only)
+ ------------------------------------------
+ Setting a bit in this register sets
+ the corresponding bin in ACX_HINT_MASK register
+ without effecting the mask
+ state of other bits (0 = no effect).
+==============================================*/
+ ACX_REG_HINT_MASK_SET,
+
+/*=============================================
+ Host Interrupt Mask Clear 16bit,(Write only)
+ ------------------------------------------
+ Setting a bit in this register clears
+ the corresponding bin in ACX_HINT_MASK register
+ without effecting the mask
+ state of other bits (0 = no effect).
+=============================================*/
+ ACX_REG_HINT_MASK_CLR,
+
+/*=============================================
+ Host Interrupt Status Nondestructive Read
+ 16bit,(Read only)
+ ------------------------------------------
+ The host can read this register to determine
+ which interrupts are active.
+ Reading this register doesn't
+ effect its content.
+=============================================*/
+ ACX_REG_INTERRUPT_NO_CLEAR,
+
+/*=============================================
+ Host Interrupt Status Clear on Read Register
+ 16bit,(Read only)
+ ------------------------------------------
+ The host can read this register to determine
+ which interrupts are active.
+ Reading this register clears it,
+ thus making all interrupts inactive.
+==============================================*/
+ ACX_REG_INTERRUPT_CLEAR,
+
+/*=============================================
+ Host Interrupt Acknowledge Register
+ 16bit,(Write only)
+ ------------------------------------------
+ The host can set individual bits in this
+ register to clear (acknowledge) the corresp.
+ interrupt status bits in the HINT_STS_CLR and
+ HINT_STS_ND registers, thus making the
+ assotiated interrupt inactive. (0-no effect)
+==============================================*/
+ ACX_REG_INTERRUPT_ACK,
+
+/*===============================================
+ Host Software Reset - 32bit RW
+ ------------------------------------------
+ [31:1] Reserved
+ 0 SOFT_RESET Soft Reset - When this bit is set,
+ it holds the Wlan hardware in a soft reset state.
+ This reset disables all MAC and baseband processor
+ clocks except the CardBus/PCI interface clock.
+ It also initializes all MAC state machines except
+ the host interface. It does not reload the
+ contents of the EEPROM. When this bit is cleared
+ (not self-clearing), the Wlan hardware
+ exits the software reset state.
+===============================================*/
+ ACX_REG_SLV_SOFT_RESET,
+
+/*===============================================
+ EEPROM Burst Read Start - 32bit RW
+ ------------------------------------------
+ [31:1] Reserved
+ 0 ACX_EE_START - EEPROM Burst Read Start 0
+ Setting this bit starts a burst read from
+ the external EEPROM.
+ If this bit is set (after reset) before an EEPROM read/write,
+ the burst read starts at EEPROM address 0.
+ Otherwise, it starts at the address
+ following the address of the previous access.
+ TheWlan hardware hardware clears this bit automatically.
+
+ Default: 0x00000000
+*================================================*/
+ ACX_REG_EE_START,
+
+/* Embedded ARM CPU Control */
+
+/*===============================================
+ Halt eCPU - 32bit RW
+ ------------------------------------------
+ 0 HALT_ECPU Halt Embedded CPU - This bit is the
+ compliment of bit 1 (MDATA2) in the SOR_CFG register.
+ During a hardware reset, this bit holds
+ the inverse of MDATA2.
+ When downloading firmware from the host,
+ set this bit (pull down MDATA2).
+ The host clears this bit after downloading the firmware into
+ zero-wait-state SSRAM.
+ When loading firmware from Flash, clear this bit (pull up MDATA2)
+ so that the eCPU can run the bootloader code in Flash
+ HALT_ECPU eCPU State
+ --------------------
+ 1 halt eCPU
+ 0 enable eCPU
+ ===============================================*/
+ ACX_REG_ECPU_CONTROL,
+
+ ACX_REG_TABLE_LEN
+};
+
+#define ACX_SLV_SOFT_RESET_BIT BIT(1)
+#define ACX_REG_EEPROM_START_BIT BIT(1)
+
+/* Command/Information Mailbox Pointers */
+
+/*===============================================
+ Command Mailbox Pointer - 32bit RW
+ ------------------------------------------
+ This register holds the start address of
+ the command mailbox located in the Wlan hardware memory.
+ The host must read this pointer after a reset to
+ find the location of the command mailbox.
+ The Wlan hardware initializes the command mailbox
+ pointer with the default address of the command mailbox.
+ The command mailbox pointer is not valid until after
+ the host receives the Init Complete interrupt from
+ the Wlan hardware.
+ ===============================================*/
+#define REG_COMMAND_MAILBOX_PTR (SCR_PAD0)
+
+/*===============================================
+ Information Mailbox Pointer - 32bit RW
+ ------------------------------------------
+ This register holds the start address of
+ the information mailbox located in the Wlan hardware memory.
+ The host must read this pointer after a reset to find
+ the location of the information mailbox.
+ The Wlan hardware initializes the information mailbox pointer
+ with the default address of the information mailbox.
+ The information mailbox pointer is not valid
+ until after the host receives the Init Complete interrupt from
+ the Wlan hardware.
+ ===============================================*/
+#define REG_EVENT_MAILBOX_PTR (SCR_PAD1)
+
+
+/* Misc */
+
+#define REG_ENABLE_TX_RX (ENABLE)
+/*
+ * Rx configuration (filter) information element
+ * ---------------------------------------------
+ */
+#define REG_RX_CONFIG (RX_CFG)
+#define REG_RX_FILTER (RX_FILTER_CFG)
+
+
+#define RX_CFG_ENABLE_PHY_HEADER_PLCP 0x0002
+
+/* promiscuous - receives all valid frames */
+#define RX_CFG_PROMISCUOUS 0x0008
+
+/* receives frames from any BSSID */
+#define RX_CFG_BSSID 0x0020
+
+/* receives frames destined to any MAC address */
+#define RX_CFG_MAC 0x0010
+
+#define RX_CFG_ENABLE_ONLY_MY_DEST_MAC 0x0010
+#define RX_CFG_ENABLE_ANY_DEST_MAC 0x0000
+#define RX_CFG_ENABLE_ONLY_MY_BSSID 0x0020
+#define RX_CFG_ENABLE_ANY_BSSID 0x0000
+
+/* discards all broadcast frames */
+#define RX_CFG_DISABLE_BCAST 0x0200
+
+#define RX_CFG_ENABLE_ONLY_MY_SSID 0x0400
+#define RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR 0x0800
+#define RX_CFG_COPY_RX_STATUS 0x2000
+#define RX_CFG_TSF 0x10000
+
+#define RX_CONFIG_OPTION_ANY_DST_MY_BSS (RX_CFG_ENABLE_ANY_DEST_MAC | \
+ RX_CFG_ENABLE_ONLY_MY_BSSID)
+
+#define RX_CONFIG_OPTION_MY_DST_ANY_BSS (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\
+ | RX_CFG_ENABLE_ANY_BSSID)
+
+#define RX_CONFIG_OPTION_ANY_DST_ANY_BSS (RX_CFG_ENABLE_ANY_DEST_MAC | \
+ RX_CFG_ENABLE_ANY_BSSID)
+
+#define RX_CONFIG_OPTION_MY_DST_MY_BSS (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\
+ | RX_CFG_ENABLE_ONLY_MY_BSSID)
+
+#define RX_CONFIG_OPTION_FOR_SCAN (RX_CFG_ENABLE_PHY_HEADER_PLCP \
+ | RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR \
+ | RX_CFG_COPY_RX_STATUS | RX_CFG_TSF)
+
+#define RX_CONFIG_OPTION_FOR_MEASUREMENT (RX_CFG_ENABLE_ANY_DEST_MAC)
+
+#define RX_CONFIG_OPTION_FOR_JOIN (RX_CFG_ENABLE_ONLY_MY_BSSID | \
+ RX_CFG_ENABLE_ONLY_MY_DEST_MAC)
+
+#define RX_CONFIG_OPTION_FOR_IBSS_JOIN (RX_CFG_ENABLE_ONLY_MY_SSID | \
+ RX_CFG_ENABLE_ONLY_MY_DEST_MAC)
+
+#define RX_FILTER_OPTION_DEF (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\
+ | CFG_RX_CTL_EN | CFG_RX_BCN_EN\
+ | CFG_RX_AUTH_EN | CFG_RX_ASSOC_EN)
+
+#define RX_FILTER_OPTION_FILTER_ALL 0
+
+#define RX_FILTER_OPTION_DEF_PRSP_BCN (CFG_RX_PRSP_EN | CFG_RX_MGMT_EN\
+ | CFG_RX_RCTS_ACK | CFG_RX_BCN_EN)
+
+#define RX_FILTER_OPTION_JOIN (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\
+ | CFG_RX_BCN_EN | CFG_RX_AUTH_EN\
+ | CFG_RX_ASSOC_EN | CFG_RX_RCTS_ACK\
+ | CFG_RX_PRSP_EN)
+
+
+/*===============================================
+ Phy regs
+ ===============================================*/
+#define ACX_PHY_ADDR_REG SBB_ADDR
+#define ACX_PHY_DATA_REG SBB_DATA
+#define ACX_PHY_CTRL_REG SBB_CTL
+#define ACX_PHY_REG_WR_MASK 0x00000001ul
+#define ACX_PHY_REG_RD_MASK 0x00000002ul
+
+
+/*===============================================
+ EEPROM Read/Write Request 32bit RW
+ ------------------------------------------
+ 1 EE_READ - EEPROM Read Request 1 - Setting this bit
+ loads a single byte of data into the EE_DATA
+ register from the EEPROM location specified in
+ the EE_ADDR register.
+ The Wlan hardware hardware clears this bit automatically.
+ EE_DATA is valid when this bit is cleared.
+
+ 0 EE_WRITE - EEPROM Write Request - Setting this bit
+ writes a single byte of data from the EE_DATA register into the
+ EEPROM location specified in the EE_ADDR register.
+ The Wlan hardware hardware clears this bit automatically.
+*===============================================*/
+#define ACX_EE_CTL_REG EE_CTL
+#define EE_WRITE 0x00000001ul
+#define EE_READ 0x00000002ul
+
+/*===============================================
+ EEPROM Address - 32bit RW
+ ------------------------------------------
+ This register specifies the address
+ within the EEPROM from/to which to read/write data.
+ ===============================================*/
+#define ACX_EE_ADDR_REG EE_ADDR
+
+/*===============================================
+ EEPROM Data - 32bit RW
+ ------------------------------------------
+ This register either holds the read 8 bits of
+ data from the EEPROM or the write data
+ to be written to the EEPROM.
+ ===============================================*/
+#define ACX_EE_DATA_REG EE_DATA
+
+/*===============================================
+ EEPROM Base Address - 32bit RW
+ ------------------------------------------
+ This register holds the upper nine bits
+ [23:15] of the 24-bit Wlan hardware memory
+ address for burst reads from EEPROM accesses.
+ The EEPROM provides the lower 15 bits of this address.
+ The MSB of the address from the EEPROM is ignored.
+ ===============================================*/
+#define ACX_EE_CFG EE_CFG
+
+/*===============================================
+ GPIO Output Values -32bit, RW
+ ------------------------------------------
+ [31:16] Reserved
+ [15: 0] Specify the output values (at the output driver inputs) for
+ GPIO[15:0], respectively.
+ ===============================================*/
+#define ACX_GPIO_OUT_REG GPIO_OUT
+#define ACX_MAX_GPIO_LINES 15
+
+/*===============================================
+ Contention window -32bit, RW
+ ------------------------------------------
+ [31:26] Reserved
+ [25:16] Max (0x3ff)
+ [15:07] Reserved
+ [06:00] Current contention window value - default is 0x1F
+ ===============================================*/
+#define ACX_CONT_WIND_CFG_REG CONT_WIND_CFG
+#define ACX_CONT_WIND_MIN_MASK 0x0000007f
+#define ACX_CONT_WIND_MAX 0x03ff0000
+
+/*
+ * Indirect slave register/memory registers
+ * ----------------------------------------
+ */
+#define HW_SLAVE_REG_ADDR_REG 0x00000004
+#define HW_SLAVE_REG_DATA_REG 0x00000008
+#define HW_SLAVE_REG_CTRL_REG 0x0000000c
+
+#define SLAVE_AUTO_INC 0x00010000
+#define SLAVE_NO_AUTO_INC 0x00000000
+#define SLAVE_HOST_LITTLE_ENDIAN 0x00000000
+
+#define HW_SLAVE_MEM_ADDR_REG SLV_MEM_ADDR
+#define HW_SLAVE_MEM_DATA_REG SLV_MEM_DATA
+#define HW_SLAVE_MEM_CTRL_REG SLV_MEM_CTL
+#define HW_SLAVE_MEM_ENDIAN_REG SLV_END_CTL
+
+#define HW_FUNC_EVENT_INT_EN 0x8000
+#define HW_FUNC_EVENT_MASK_REG 0x00000034
+
+#define ACX_MAC_TIMESTAMP_REG (MAC_TIMESTAMP)
+
+/*===============================================
+ HI_CFG Interface Configuration Register Values
+ ------------------------------------------
+ ===============================================*/
+#define HI_CFG_UART_ENABLE 0x00000004
+#define HI_CFG_RST232_ENABLE 0x00000008
+#define HI_CFG_CLOCK_REQ_SELECT 0x00000010
+#define HI_CFG_HOST_INT_ENABLE 0x00000020
+#define HI_CFG_VLYNQ_OUTPUT_ENABLE 0x00000040
+#define HI_CFG_HOST_INT_ACTIVE_LOW 0x00000080
+#define HI_CFG_UART_TX_OUT_GPIO_15 0x00000100
+#define HI_CFG_UART_TX_OUT_GPIO_14 0x00000200
+#define HI_CFG_UART_TX_OUT_GPIO_7 0x00000400
+
+/*
+ * NOTE: USE_ACTIVE_HIGH compilation flag should be defined in makefile
+ * for platforms using active high interrupt level
+ */
+#ifdef USE_ACTIVE_HIGH
+#define HI_CFG_DEF_VAL \
+ (HI_CFG_UART_ENABLE | \
+ HI_CFG_RST232_ENABLE | \
+ HI_CFG_CLOCK_REQ_SELECT | \
+ HI_CFG_HOST_INT_ENABLE)
+#else
+#define HI_CFG_DEF_VAL \
+ (HI_CFG_UART_ENABLE | \
+ HI_CFG_RST232_ENABLE | \
+ HI_CFG_CLOCK_REQ_SELECT | \
+ HI_CFG_HOST_INT_ENABLE)
+
+#endif
+
+#define REF_FREQ_19_2 0
+#define REF_FREQ_26_0 1
+#define REF_FREQ_38_4 2
+#define REF_FREQ_40_0 3
+#define REF_FREQ_33_6 4
+#define REF_FREQ_NUM 5
+
+#define LUT_PARAM_INTEGER_DIVIDER 0
+#define LUT_PARAM_FRACTIONAL_DIVIDER 1
+#define LUT_PARAM_ATTN_BB 2
+#define LUT_PARAM_ALPHA_BB 3
+#define LUT_PARAM_STOP_TIME_BB 4
+#define LUT_PARAM_BB_PLL_LOOP_FILTER 5
+#define LUT_PARAM_NUM 6
+
+#define ACX_EEPROMLESS_IND_REG (SCR_PAD4)
+#define USE_EEPROM 0
+#define SOFT_RESET_MAX_TIME 1000000
+#define SOFT_RESET_STALL_TIME 1000
+#define NVS_DATA_BUNDARY_ALIGNMENT 4
+
+
+/* Firmware image load chunk size */
+#define CHUNK_SIZE 512
+
+/* Firmware image header size */
+#define FW_HDR_SIZE 8
+
+#define ECPU_CONTROL_HALT 0x00000101
+
+
+/******************************************************************************
+
+ CHANNELS, BAND & REG DOMAINS definitions
+
+******************************************************************************/
+
+
+enum {
+ RADIO_BAND_2_4GHZ = 0, /* 2.4 Ghz band */
+ RADIO_BAND_5GHZ = 1, /* 5 Ghz band */
+ RADIO_BAND_JAPAN_4_9_GHZ = 2,
+ DEFAULT_BAND = RADIO_BAND_2_4GHZ,
+ INVALID_BAND = 0xFE,
+ MAX_RADIO_BANDS = 0xFF
+};
+
+enum {
+ NO_RATE = 0,
+ RATE_1MBPS = 0x0A,
+ RATE_2MBPS = 0x14,
+ RATE_5_5MBPS = 0x37,
+ RATE_6MBPS = 0x0B,
+ RATE_9MBPS = 0x0F,
+ RATE_11MBPS = 0x6E,
+ RATE_12MBPS = 0x0A,
+ RATE_18MBPS = 0x0E,
+ RATE_22MBPS = 0xDC,
+ RATE_24MBPS = 0x09,
+ RATE_36MBPS = 0x0D,
+ RATE_48MBPS = 0x08,
+ RATE_54MBPS = 0x0C
+};
+
+enum {
+ RATE_INDEX_1MBPS = 0,
+ RATE_INDEX_2MBPS = 1,
+ RATE_INDEX_5_5MBPS = 2,
+ RATE_INDEX_6MBPS = 3,
+ RATE_INDEX_9MBPS = 4,
+ RATE_INDEX_11MBPS = 5,
+ RATE_INDEX_12MBPS = 6,
+ RATE_INDEX_18MBPS = 7,
+ RATE_INDEX_22MBPS = 8,
+ RATE_INDEX_24MBPS = 9,
+ RATE_INDEX_36MBPS = 10,
+ RATE_INDEX_48MBPS = 11,
+ RATE_INDEX_54MBPS = 12,
+ RATE_INDEX_MAX = RATE_INDEX_54MBPS,
+ MAX_RATE_INDEX,
+ INVALID_RATE_INDEX = MAX_RATE_INDEX,
+ RATE_INDEX_ENUM_MAX_SIZE = 0x7FFFFFFF
+};
+
+enum {
+ RATE_MASK_1MBPS = 0x1,
+ RATE_MASK_2MBPS = 0x2,
+ RATE_MASK_5_5MBPS = 0x4,
+ RATE_MASK_11MBPS = 0x20,
+};
+
+#define SHORT_PREAMBLE_BIT BIT(0) /* CCK or Barker depending on the rate */
+#define OFDM_RATE_BIT BIT(6)
+#define PBCC_RATE_BIT BIT(7)
+
+enum {
+ CCK_LONG = 0,
+ CCK_SHORT = SHORT_PREAMBLE_BIT,
+ PBCC_LONG = PBCC_RATE_BIT,
+ PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT,
+ OFDM = OFDM_RATE_BIT
+};
+
+/******************************************************************************
+
+Transmit-Descriptor RATE-SET field definitions...
+
+Define a new "Rate-Set" for TX path that incorporates the
+Rate & Modulation info into a single 16-bit field.
+
+TxdRateSet_t:
+b15 - Indicates Preamble type (1=SHORT, 0=LONG).
+ Notes:
+ Must be LONG (0) for 1Mbps rate.
+ Does not apply (set to 0) for RevG-OFDM rates.
+b14 - Indicates PBCC encoding (1=PBCC, 0=not).
+ Notes:
+ Does not apply (set to 0) for rates 1 and 2 Mbps.
+ Does not apply (set to 0) for RevG-OFDM rates.
+b13 - Unused (set to 0).
+b12-b0 - Supported Rate indicator bits as defined below.
+
+******************************************************************************/
+
+
+#define TNETW1251_CHIP_ID_PG1_0 0x07010101
+#define TNETW1251_CHIP_ID_PG1_1 0x07020101
+#define TNETW1251_CHIP_ID_PG1_2 0x07030101
+
+/*************************************************************************
+
+ Interrupt Trigger Register (Host -> WiLink)
+
+**************************************************************************/
+
+/* Hardware to Embedded CPU Interrupts - first 32-bit register set */
+
+/*
+ * Host Command Interrupt. Setting this bit masks
+ * the interrupt that the host issues to inform
+ * the FW that it has sent a command
+ * to the Wlan hardware Command Mailbox.
+ */
+#define INTR_TRIG_CMD BIT(0)
+
+/*
+ * Host Event Acknowlegde Interrupt. The host
+ * sets this bit to acknowledge that it received
+ * the unsolicited information from the event
+ * mailbox.
+ */
+#define INTR_TRIG_EVENT_ACK BIT(1)
+
+/*
+ * The host sets this bit to inform the Wlan
+ * FW that a TX packet is in the XFER
+ * Buffer #0.
+ */
+#define INTR_TRIG_TX_PROC0 BIT(2)
+
+/*
+ * The host sets this bit to inform the FW
+ * that it read a packet from RX XFER
+ * Buffer #0.
+ */
+#define INTR_TRIG_RX_PROC0 BIT(3)
+
+#define INTR_TRIG_DEBUG_ACK BIT(4)
+
+#define INTR_TRIG_STATE_CHANGED BIT(5)
+
+
+/* Hardware to Embedded CPU Interrupts - second 32-bit register set */
+
+/*
+ * The host sets this bit to inform the FW
+ * that it read a packet from RX XFER
+ * Buffer #1.
+ */
+#define INTR_TRIG_RX_PROC1 BIT(17)
+
+/*
+ * The host sets this bit to inform the Wlan
+ * hardware that a TX packet is in the XFER
+ * Buffer #1.
+ */
+#define INTR_TRIG_TX_PROC1 BIT(18)
+
+#endif
@@ -26,7 +26,7 @@
#include <net/mac80211.h>
#include "wl1251.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_io.h"
#include "wl1251_rx.h"
#include "wl1251_cmd.h"
@@ -29,7 +29,7 @@
#include "wl1251.h"
#include "wl12xx_80211.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_ps.h"
#include "wl1251_io.h"
#include "wl1251_tx.h"
@@ -28,7 +28,7 @@
#include <linux/spi/wl12xx.h>
#include "wl1251.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_spi.h"
static irqreturn_t wl1251_irq(int irq, void *cookie)
@@ -27,7 +27,7 @@
#include "wl1251_cmd.h"
#include "wl1251_acx.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#define WSPI_CMD_READ 0x40000000
#define WSPI_CMD_WRITE 0x00000000
@@ -26,7 +26,7 @@
#include <linux/module.h>
#include "wl1251.h"
-#include "reg.h"
+#include "wl1251_reg.h"
#include "wl1251_tx.h"
#include "wl1251_ps.h"
#include "wl1251_io.h"