@@ -148,6 +148,10 @@
* @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to
* destination %NL80211_ATTR_MAC on the interface identified by
* %NL80211_ATTR_IFINDEX.
+ * @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by
+ * %NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP.
+ * @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by
+ * %NL80211_ATTR_MAC.
* @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the
* the interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC
@@ -612,7 +616,7 @@ enum nl80211_commands {
* consisting of a nested array.
*
* @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).
- * @NL80211_ATTR_PLINK_ACTION: action to perform on the mesh peer link.
+ * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link.
* @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path.
* @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path
* info given for %NL80211_CMD_GET_MPATH, nested attribute described at
@@ -879,7 +883,9 @@ enum nl80211_commands {
* See &enum nl80211_key_default_types.
*
* @NL80211_ATTR_MESH_SETUP: Optional mesh setup parameters. These cannot be
- * changed once the mesh is active.
+ * changed once the mesh is active.
+ * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute
+ * containing attributes from &enum nl80211_meshconf_params.
*
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
@@ -1225,8 +1231,6 @@ enum nl80211_rate_info {
* @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs)
* @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station)
* @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station)
- * @__NL80211_STA_INFO_AFTER_LAST: internal
- * @NL80211_STA_INFO_MAX: highest possible station info attribute
* @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
* @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
* containing info as possible, see &enum nl80211_sta_info_txrate.
@@ -1236,6 +1240,11 @@ enum nl80211_rate_info {
* @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station)
* @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station)
* @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm)
+ * @NL80211_STA_INFO_LLID: the station's mesh LLID
+ * @NL80211_STA_INFO_PLID: the station's mesh PLID
+ * @NL80211_STA_INFO_PLINK_STATE: peer link state for the station
+ * @__NL80211_STA_INFO_AFTER_LAST: internal
+ * @NL80211_STA_INFO_MAX: highest possible station info attribute
*/
enum nl80211_sta_info {
__NL80211_STA_INFO_INVALID,
@@ -1626,7 +1635,7 @@ enum nl80211_mntr_flags {
* @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs)
* that it takes for an HWMP information element to propagate across the mesh
*
- * @NL80211_MESHCONF_ROOTMODE: whether root mode is enabled or not
+ * @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not
*
* @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
* source mesh point for path selection elements.
@@ -1678,6 +1687,7 @@ enum nl80211_meshconf_params {
* element that vendors will use to identify the path selection methods and
* metrics in use.
*
+ * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
* @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
*/
enum nl80211_mesh_setup_params {