@@ -7,7 +7,7 @@ menu "Near Field Communication (NFC) devices"
config NFC_TRF7970A
tristate "Texas Instruments TRF7970a NFC driver"
- depends on SPI && NFC_DIGITAL
+ depends on SPI && NFC_DIGITAL && GPIOLIB
help
This option enables the NFC driver for Texas Instruments' TRF7970a
device. Such device supports 5 different protocols: ISO14443A,
@@ -20,9 +20,8 @@
#include <linux/nfc.h>
#include <linux/skbuff.h>
#include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/of.h>
-#include <linux/of_gpio.h>
#include <linux/spi/spi.h>
#include <linux/regulator/consumer.h>
@@ -452,8 +451,8 @@ struct trf7970a {
u8 tx_cmd;
bool issue_eof;
bool adjust_resp_len;
- int en2_gpio;
- int en_gpio;
+ struct gpio_desc *en_gpiod;
+ struct gpio_desc *en2_gpiod;
struct mutex lock;
unsigned int timeout;
bool ignore_timeout;
@@ -1908,14 +1907,13 @@ static int trf7970a_power_up(struct trf7970a *trf)
usleep_range(5000, 6000);
- if (!(trf->quirks & TRF7970A_QUIRK_EN2_MUST_STAY_LOW)) {
- if (gpio_is_valid(trf->en2_gpio)) {
- gpio_set_value(trf->en2_gpio, 1);
- usleep_range(1000, 2000);
- }
+ if (trf->en2_gpiod &&
+ !(trf->quirks & TRF7970A_QUIRK_EN2_MUST_STAY_LOW)) {
+ gpiod_set_value_cansleep(trf->en2_gpiod, 1);
+ usleep_range(1000, 2000);
}
- gpio_set_value(trf->en_gpio, 1);
+ gpiod_set_value_cansleep(trf->en_gpiod, 1);
usleep_range(20000, 21000);
@@ -1939,11 +1937,11 @@ static int trf7970a_power_down(struct trf7970a *trf)
return -EBUSY;
}
- gpio_set_value(trf->en_gpio, 0);
+ gpiod_set_value_cansleep(trf->en_gpiod, 0);
- if (!(trf->quirks & TRF7970A_QUIRK_EN2_MUST_STAY_LOW))
- if (gpio_is_valid(trf->en2_gpio))
- gpio_set_value(trf->en2_gpio, 0);
+ if (trf->en2_gpiod &&
+ !(trf->quirks & TRF7970A_QUIRK_EN2_MUST_STAY_LOW))
+ gpiod_set_value_cansleep(trf->en2_gpiod, 0);
ret = regulator_disable(trf->regulator);
if (ret)
@@ -2041,32 +2039,23 @@ static int trf7970a_probe(struct spi_device *spi)
trf->quirks |= TRF7970A_QUIRK_IRQ_STATUS_READ;
/* There are two enable pins - only EN must be present in the DT */
- trf->en_gpio = of_get_named_gpio(np, "ti,enable-gpios", 0);
- if (!gpio_is_valid(trf->en_gpio)) {
+ trf->en_gpiod = devm_gpiod_get_index(trf->dev, "ti,enable", 0,
+ GPIOD_OUT_LOW);
+ if (IS_ERR(trf->en_gpiod)) {
dev_err(trf->dev, "No EN GPIO property\n");
- return trf->en_gpio;
- }
-
- ret = devm_gpio_request_one(trf->dev, trf->en_gpio,
- GPIOF_DIR_OUT | GPIOF_INIT_LOW, "trf7970a EN");
- if (ret) {
- dev_err(trf->dev, "Can't request EN GPIO: %d\n", ret);
- return ret;
+ return PTR_ERR(trf->en_gpiod);
}
- trf->en2_gpio = of_get_named_gpio(np, "ti,enable-gpios", 1);
- if (!gpio_is_valid(trf->en2_gpio)) {
+ trf->en2_gpiod = devm_gpiod_get_index_optional(trf->dev, "ti,enable", 1,
+ GPIOD_OUT_LOW);
+ if (!trf->en2_gpiod) {
dev_info(trf->dev, "No EN2 GPIO property\n");
- } else {
- ret = devm_gpio_request_one(trf->dev, trf->en2_gpio,
- GPIOF_DIR_OUT | GPIOF_INIT_LOW, "trf7970a EN2");
- if (ret) {
- dev_err(trf->dev, "Can't request EN2 GPIO: %d\n", ret);
- return ret;
- }
-
- if (of_property_read_bool(np, "en2-rf-quirk"))
- trf->quirks |= TRF7970A_QUIRK_EN2_MUST_STAY_LOW;
+ } else if (IS_ERR(trf->en2_gpiod)) {
+ dev_err(trf->dev, "Error getting EN2 GPIO property: %ld\n",
+ PTR_ERR(trf->en2_gpiod));
+ return PTR_ERR(trf->en2_gpiod);
+ } else if (of_property_read_bool(np, "en2-rf-quirk")) {
+ trf->quirks |= TRF7970A_QUIRK_EN2_MUST_STAY_LOW;
}
of_property_read_u32(np, "clock-frequency", &clk_freq);
The trf7970a driver uses the deprecated integer-based GPIO consumer interface so convert it to use the new descriptor-based GPIO consumer interface. Signed-off-by: Mark Greer <mgreer@animalcreek.com> --- drivers/nfc/Kconfig | 2 +- drivers/nfc/trf7970a.c | 61 +++++++++++++++++++++----------------------------- 2 files changed, 26 insertions(+), 37 deletions(-)