@@ -47,6 +47,7 @@ source "drivers/net/wireless/st/Kconfig"
source "drivers/net/wireless/ti/Kconfig"
source "drivers/net/wireless/zydas/Kconfig"
source "drivers/net/wireless/quantenna/Kconfig"
+source "drivers/net/wireless/microchip/Kconfig"
config PCMCIA_RAYCS
tristate "Aviator/Raytheon 2.4GHz wireless support"
@@ -19,6 +19,7 @@ obj-$(CONFIG_WLAN_VENDOR_ST) += st/
obj-$(CONFIG_WLAN_VENDOR_TI) += ti/
obj-$(CONFIG_WLAN_VENDOR_ZYDAS) += zydas/
obj-$(CONFIG_WLAN_VENDOR_QUANTENNA) += quantenna/
+obj-$(CONFIG_WLAN_VENDOR_MICROCHIP) += microchip/
# 16-bit wireless PCMCIA client drivers
obj-$(CONFIG_PCMCIA_RAYCS) += ray_cs.o
new file mode 100644
@@ -0,0 +1,15 @@
+# SPDX-License-Identifier: GPL-2.0
+config WLAN_VENDOR_MICROCHIP
+ bool "Microchip devices"
+ default y
+ help
+ If you have a wireless card belonging to this class, say Y.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all the
+ questions about these cards. If you say Y, you will be asked for
+ your specific card in the following questions.
+
+if WLAN_VENDOR_MICROCHIP
+source "drivers/net/wireless/microchip/wilc1000/Kconfig"
+endif # WLAN_VENDOR_MICROCHIP
new file mode 100644
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_WILC1000) += wilc1000/
new file mode 100644
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: GPL-2.0
+config WILC1000
+ tristate
+ help
+ Add support for the Atmel WILC1000 802.11 b/g/n SoC.
+ This provides Wi-FI over an SDIO or SPI interface, and
+ is usually found in IoT devices.
+
+ This module only support IEEE 802.11n WiFi.
+
+config WILC1000_SDIO
+ tristate "Atmel WILC1000 SDIO (WiFi only)"
+ depends on CFG80211 && INET && MMC
+ select WILC1000
+ help
+ This module adds support for the SDIO interface of adapters using
+ WILC1000 chipset. The Atmel WILC1000 SDIO is a full speed interface.
+ It meets SDIO card specification version 2.0. The interface supports
+ the 1-bit/4-bit SD transfer mode at the clock range of 0-50 MHz.
+ The host can use this interface to read and write from any register
+ within the chip as well as configure the WILC1000 for data DMA.
+ To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
+ this if your platform is using the SDIO bus.
+
+config WILC1000_SPI
+ tristate "Atmel WILC1000 SPI (WiFi only)"
+ depends on CFG80211 && INET && SPI
+ select WILC1000
+ select CRC7
+ help
+ This module adds support for the SPI interface of adapters using
+ WILC1000 chipset. The Atmel WILC1000 has a Serial Peripheral
+ Interface (SPI) that operates as a SPI slave. This SPI interface can
+ be used for control and for serial I/O of 802.11 data. The SPI is a
+ full-duplex slave synchronous serial interface that is available
+ immediately following reset when pin 9 (SDIO_SPI_CFG) is tied to
+ VDDIO. Select this if your platform is using the SPI bus.
+
+config WILC1000_HW_OOB_INTR
+ bool "WILC1000 out of band interrupt"
+ depends on WILC1000_SDIO
+ help
+ This option enables out-of-band interrupt support for the WILC1000
+ chipset. This OOB interrupt is intended to provide a faster interrupt
+ mechanism for SDIO host controllers that don't support SDIO interrupt.
+ Select this option If the SDIO host controller in your platform
+ doesn't support SDIO time devision interrupt.
new file mode 100644
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_WILC1000) += wilc1000.o
+
+ccflags-y += -DFIRMWARE_1002=\"atmel/wilc1002_firmware.bin\" \
+ -DFIRMWARE_1003=\"atmel/wilc1003_firmware.bin\"
+
+wilc1000-objs := cfg80211.o netdev.o mon.o \
+ hif.o wlan_cfg.o wlan.o
+
+obj-$(CONFIG_WILC1000_SDIO) += wilc1000-sdio.o
+wilc1000-sdio-objs += sdio.o
+
+obj-$(CONFIG_WILC1000_SPI) += wilc1000-spi.o
+wilc1000-spi-objs += spi.o
@@ -80,8 +80,6 @@ source "drivers/staging/fbtft/Kconfig"
source "drivers/staging/fsl-dpaa2/Kconfig"
-source "drivers/staging/wilc1000/Kconfig"
-
source "drivers/staging/most/Kconfig"
source "drivers/staging/ks7010/Kconfig"
@@ -30,7 +30,6 @@ obj-$(CONFIG_UNISYSSPAR) += unisys/
obj-$(CONFIG_COMMON_CLK_XLNX_CLKWZRD) += clocking-wizard/
obj-$(CONFIG_FB_TFT) += fbtft/
obj-$(CONFIG_FSL_DPAA2) += fsl-dpaa2/
-obj-$(CONFIG_WILC1000) += wilc1000/
obj-$(CONFIG_MOST) += most/
obj-$(CONFIG_KS7010) += ks7010/
obj-$(CONFIG_GREYBUS) += greybus/