diff mbox series

[3/6] ath9k: use AR9300_MAX_CHAINS when appropriate

Message ID 20220320233010.123106-4-wlooi@ucalgary.ca (mailing list archive)
State Accepted
Commit 3096a4d9eb9bf8a0975c222bd7013d2db323d749
Delegated to: Kalle Valo
Headers show
Series ath9k: suggested improvements and bugfixes | expand

Commit Message

Wenli Looi March 20, 2022, 11:30 p.m. UTC
Replace other constants with AR9300_MAX_CHAINS when appropriate.

This change does not appear to affect the final binary.

Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>
---
 drivers/net/wireless/ath/ath9k/ar9003_calib.c  | 2 +-
 drivers/net/wireless/ath/ath9k/ar9003_eeprom.c | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

Comments

Toke Høiland-Jørgensen March 21, 2022, 4:02 p.m. UTC | #1
Wenli Looi <wlooi@ucalgary.ca> writes:

> Replace other constants with AR9300_MAX_CHAINS when appropriate.
>
> This change does not appear to affect the final binary.
>
> Signed-off-by: Wenli Looi <wlooi@ucalgary.ca>

Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
diff mbox series

Patch

diff --git a/drivers/net/wireless/ath/ath9k/ar9003_calib.c b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
index dc24da1ff..6ca089f15 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_calib.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_calib.c
@@ -177,7 +177,7 @@  static void ar9003_hw_iqcal_collect(struct ath_hw *ah)
 	int i;
 
 	/* Accumulate IQ cal measures for active chains */
-	for (i = 0; i < AR5416_MAX_CHAINS; i++) {
+	for (i = 0; i < AR9300_MAX_CHAINS; i++) {
 		if (ah->txchainmask & BIT(i)) {
 			ah->totalPowerMeasI[i] +=
 				REG_READ(ah, AR_PHY_CAL_MEAS_0(i));
diff --git a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
index b0a4ca355..669b49b56 100644
--- a/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
+++ b/drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
@@ -3911,7 +3911,7 @@  static void ar9003_hw_atten_apply(struct ath_hw *ah, struct ath9k_channel *chan)
 	}
 
 	/* Test value. if 0 then attenuation is unused. Don't load anything. */
-	for (i = 0; i < 3; i++) {
+	for (i = 0; i < AR9300_MAX_CHAINS; i++) {
 		if (ah->txchainmask & BIT(i)) {
 			value = ar9003_hw_atten_chain_get(ah, i, chan);
 			REG_RMW_FIELD(ah, ext_atten_reg[i],
@@ -5126,7 +5126,7 @@  static int ar9003_hw_calibration_apply(struct ath_hw *ah, int frequency)
 		frequency, correction[0], correction[1], correction[2]);
 
 	/* Store calibrated noise floor values */
-	for (ichain = 0; ichain < AR5416_MAX_CHAINS; ichain++)
+	for (ichain = 0; ichain < AR9300_MAX_CHAINS; ichain++)
 		if (mode) {
 			ah->nf_5g.cal[ichain] = nf_cal[ichain];
 			ah->nf_5g.pwr[ichain] = nf_pwr[ichain];