@@ -1,7 +1,7 @@
// SPDX-License-Identifier: GPL-2.0-only
/*
* mac80211 - channel management
- * Copyright 2020 - 2022 Intel Corporation
+ * Copyright 2020 - 2023 Intel Corporation
*/
#include <linux/nl80211.h>
@@ -382,7 +382,7 @@ _ieee80211_recalc_chanctx_min_def(struct ieee80211_local *local,
/* downgrade chandef up to max_bw */
min_def = ctx->conf.def;
while (min_def.width > max_bw)
- ieee80211_chandef_downgrade(&min_def);
+ ieee80211_chandef_downgrade(&min_def, NULL);
if (cfg80211_chandef_identical(&ctx->conf.min_def, &min_def))
return 0;
@@ -152,16 +152,17 @@ do { \
else \
_sdata_err((link)->sdata, fmt, ##__VA_ARGS__); \
} while (0)
+#define _link_id_dbg(print, sdata, link_id, fmt, ...) \
+ do { \
+ if (ieee80211_vif_is_mld(&(sdata)->vif)) \
+ _sdata_dbg(print, sdata, "[link %d] " fmt, \
+ link_id, ##__VA_ARGS__); \
+ else \
+ _sdata_dbg(1, sdata, fmt, ##__VA_ARGS__); \
+ } while (0)
#define link_dbg(link, fmt, ...) \
- do { \
- if (ieee80211_vif_is_mld(&(link)->sdata->vif)) \
- _sdata_dbg(1, (link)->sdata, "[link %d] " fmt, \
- (link)->link_id, \
- ##__VA_ARGS__); \
- else \
- _sdata_dbg(1, (link)->sdata, fmt, \
- ##__VA_ARGS__); \
- } while (0)
+ _link_id_dbg(1, (link)->sdata, (link)->link_id, \
+ fmt, ##__VA_ARGS__)
#define ht_dbg(sdata, fmt, ...) \
_sdata_dbg(MAC80211_HT_DEBUG, \
@@ -226,6 +227,9 @@ do { \
#define mlme_dbg(sdata, fmt, ...) \
_sdata_dbg(MAC80211_MLME_DEBUG, \
sdata, fmt, ##__VA_ARGS__)
+#define mlme_link_id_dbg(sdata, link_id, fmt, ...) \
+ _link_id_dbg(MAC80211_MLME_DEBUG, sdata, link_id, \
+ fmt, ##__VA_ARGS__)
#define mlme_dbg_ratelimited(sdata, fmt, ...) \
_sdata_dbg(MAC80211_MLME_DEBUG && net_ratelimit(), \
@@ -757,21 +757,22 @@ ieee80211_ibss_process_chanswitch(struct ieee80211_sub_if_data *sdata,
struct ieee80211_if_ibss *ifibss = &sdata->u.ibss;
enum nl80211_channel_type ch_type;
int err;
- ieee80211_conn_flags_t conn_flags;
+ struct ieee80211_conn_settings conn = {
+ .mode = IEEE80211_CONN_MODE_HT,
+ .bw_limit = IEEE80211_CONN_BW_LIMIT_40,
+ };
u32 vht_cap_info = 0;
lockdep_assert_wiphy(sdata->local->hw.wiphy);
- conn_flags = IEEE80211_CONN_DISABLE_VHT;
-
switch (ifibss->chandef.width) {
case NL80211_CHAN_WIDTH_5:
case NL80211_CHAN_WIDTH_10:
case NL80211_CHAN_WIDTH_20_NOHT:
- conn_flags |= IEEE80211_CONN_DISABLE_HT;
+ conn.mode = IEEE80211_CONN_MODE_LEGACY;
fallthrough;
case NL80211_CHAN_WIDTH_20:
- conn_flags |= IEEE80211_CONN_DISABLE_40MHZ;
+ conn.bw_limit = IEEE80211_CONN_BW_LIMIT_20;
break;
default:
break;
@@ -783,8 +784,8 @@ ieee80211_ibss_process_chanswitch(struct ieee80211_sub_if_data *sdata,
memset(¶ms, 0, sizeof(params));
err = ieee80211_parse_ch_switch_ie(sdata, elems,
ifibss->chandef.chan->band,
- vht_cap_info,
- conn_flags, ifibss->bssid, &csa_ie);
+ vht_cap_info, &conn,
+ ifibss->bssid, &csa_ie);
/* can't switch to destination channel, fail */
if (err < 0)
goto disconnect;
@@ -5,7 +5,7 @@
* Copyright 2006-2007 Jiri Benc <jbenc@suse.cz>
* Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net>
* Copyright 2013-2015 Intel Mobile Communications GmbH
- * Copyright (C) 2018-2022 Intel Corporation
+ * Copyright (C) 2018-2023 Intel Corporation
*/
#ifndef IEEE80211_I_H
@@ -367,19 +367,32 @@ enum ieee80211_sta_flags {
IEEE80211_STA_ENABLE_RRM = BIT(15),
};
-typedef u32 __bitwise ieee80211_conn_flags_t;
-
-enum ieee80211_conn_flags {
- IEEE80211_CONN_DISABLE_HT = (__force ieee80211_conn_flags_t)BIT(0),
- IEEE80211_CONN_DISABLE_40MHZ = (__force ieee80211_conn_flags_t)BIT(1),
- IEEE80211_CONN_DISABLE_VHT = (__force ieee80211_conn_flags_t)BIT(2),
- IEEE80211_CONN_DISABLE_80P80MHZ = (__force ieee80211_conn_flags_t)BIT(3),
- IEEE80211_CONN_DISABLE_160MHZ = (__force ieee80211_conn_flags_t)BIT(4),
- IEEE80211_CONN_DISABLE_HE = (__force ieee80211_conn_flags_t)BIT(5),
- IEEE80211_CONN_DISABLE_EHT = (__force ieee80211_conn_flags_t)BIT(6),
- IEEE80211_CONN_DISABLE_320MHZ = (__force ieee80211_conn_flags_t)BIT(7),
+enum ieee80211_conn_mode {
+ IEEE80211_CONN_MODE_S1G,
+ IEEE80211_CONN_MODE_LEGACY,
+ IEEE80211_CONN_MODE_HT,
+ IEEE80211_CONN_MODE_VHT,
+ IEEE80211_CONN_MODE_HE,
+ IEEE80211_CONN_MODE_EHT,
};
+#define IEEE80211_CONN_MODE_HIGHEST IEEE80211_CONN_MODE_EHT
+
+enum ieee80211_conn_bw_limit {
+ IEEE80211_CONN_BW_LIMIT_20,
+ IEEE80211_CONN_BW_LIMIT_40,
+ IEEE80211_CONN_BW_LIMIT_80,
+ IEEE80211_CONN_BW_LIMIT_160, /* also 80+80 */
+ IEEE80211_CONN_BW_LIMIT_320,
+};
+
+struct ieee80211_conn_settings {
+ enum ieee80211_conn_mode mode;
+ enum ieee80211_conn_bw_limit bw_limit;
+};
+
+extern const struct ieee80211_conn_settings ieee80211_conn_settings_unlimited;
+
struct ieee80211_mgd_auth_data {
struct cfg80211_bss *bss;
unsigned long timeout;
@@ -413,7 +426,7 @@ struct ieee80211_mgd_assoc_data {
size_t elems_len;
u8 *elems; /* pointing to inside ie[] below */
- ieee80211_conn_flags_t conn_flags;
+ struct ieee80211_conn_settings conn;
u16 status;
@@ -934,7 +947,7 @@ struct ieee80211_link_data_managed {
enum ieee80211_smps_mode req_smps, /* requested smps mode */
driver_smps_mode; /* smps mode request */
- ieee80211_conn_flags_t conn_flags;
+ struct ieee80211_conn_settings conn;
s16 p2p_noa_index;
@@ -2163,9 +2176,8 @@ void ieee80211_process_measurement_req(struct ieee80211_sub_if_data *sdata,
* @elems: parsed 802.11 elements received with the frame
* @current_band: indicates the current band
* @vht_cap_info: VHT capabilities of the transmitter
- * @conn_flags: contains information about own capabilities and restrictions
- * to decide which channel switch announcements can be accepted, using
- * flags from &enum ieee80211_conn_flags.
+ * @conn: contains information about own capabilities and restrictions
+ * to decide which channel switch announcements can be accepted
* @bssid: the currently connected bssid (for reporting)
* @csa_ie: parsed 802.11 csa elements on count, mode, chandef and mesh ttl.
* All of them will be filled with if success only.
@@ -2175,7 +2187,8 @@ int ieee80211_parse_ch_switch_ie(struct ieee80211_sub_if_data *sdata,
struct ieee802_11_elems *elems,
enum nl80211_band current_band,
u32 vht_cap_info,
- ieee80211_conn_flags_t conn_flags, u8 *bssid,
+ struct ieee80211_conn_settings *conn,
+ u8 *bssid,
struct ieee80211_csa_ie *csa_ie);
/* Suspend/resume and hw reconfiguration */
@@ -2240,6 +2253,7 @@ static inline void ieee80211_tx_skb(struct ieee80211_sub_if_data *sdata,
/**
* struct ieee80211_elems_parse_params - element parsing parameters
+ * @mode: connection mode for parsing
* @start: pointer to the elements
* @len: length of the elements
* @action: %true if the elements came from an action frame
@@ -2257,6 +2271,7 @@ static inline void ieee80211_tx_skb(struct ieee80211_sub_if_data *sdata,
* for EHT capabilities parsing)
*/
struct ieee80211_elems_parse_params {
+ enum ieee80211_conn_mode mode;
const u8 *start;
size_t len;
bool action;
@@ -2276,6 +2291,7 @@ ieee802_11_parse_elems_crc(const u8 *start, size_t len, bool action,
struct cfg80211_bss *bss)
{
struct ieee80211_elems_parse_params params = {
+ .mode = IEEE80211_CONN_MODE_HIGHEST,
.start = start,
.len = len,
.action = action,
@@ -2451,9 +2467,9 @@ u8 *ieee80211_ie_build_vht_cap(u8 *pos, struct ieee80211_sta_vht_cap *vht_cap,
u8 *ieee80211_ie_build_vht_oper(u8 *pos, struct ieee80211_sta_vht_cap *vht_cap,
const struct cfg80211_chan_def *chandef);
u8 ieee80211_ie_len_he_cap(struct ieee80211_sub_if_data *sdata, u8 iftype);
-u8 *ieee80211_ie_build_he_cap(ieee80211_conn_flags_t disable_flags, u8 *pos,
+u8 *ieee80211_ie_build_he_cap(const struct ieee80211_conn_settings *conn,
const struct ieee80211_sta_he_cap *he_cap,
- u8 *end);
+ u8 *pos, u8 *end);
void ieee80211_ie_build_he_6ghz_cap(struct ieee80211_sub_if_data *sdata,
enum ieee80211_smps_mode smps_mode,
struct sk_buff *skb);
@@ -2493,7 +2509,8 @@ bool ieee80211_chandef_he_6ghz_oper(struct ieee80211_sub_if_data *sdata,
struct cfg80211_chan_def *chandef);
bool ieee80211_chandef_s1g_oper(const struct ieee80211_s1g_oper_ie *oper,
struct cfg80211_chan_def *chandef);
-ieee80211_conn_flags_t ieee80211_chandef_downgrade(struct cfg80211_chan_def *c);
+void ieee80211_chandef_downgrade(struct cfg80211_chan_def *chandef,
+ struct ieee80211_conn_settings *conn);
int __must_check
ieee80211_link_use_channel(struct ieee80211_link_data *link,
@@ -586,7 +586,7 @@ int mesh_add_he_cap_ie(struct ieee80211_sub_if_data *sdata,
return -ENOMEM;
pos = skb_put(skb, ie_len);
- ieee80211_ie_build_he_cap(0, pos, he_cap, pos + ie_len);
+ ieee80211_ie_build_he_cap(NULL, he_cap, pos, pos + ie_len);
return 0;
}
@@ -1292,7 +1292,7 @@ ieee80211_mesh_process_chnswitch(struct ieee80211_sub_if_data *sdata,
struct ieee80211_if_mesh *ifmsh = &sdata->u.mesh;
struct ieee80211_supported_band *sband;
int err;
- ieee80211_conn_flags_t conn_flags = 0;
+ struct ieee80211_conn_settings conn = ieee80211_conn_settings_unlimited;
u32 vht_cap_info = 0;
lockdep_assert_wiphy(sdata->local->hw.wiphy);
@@ -1303,13 +1303,14 @@ ieee80211_mesh_process_chnswitch(struct ieee80211_sub_if_data *sdata,
switch (sdata->vif.bss_conf.chandef.width) {
case NL80211_CHAN_WIDTH_20_NOHT:
- conn_flags |= IEEE80211_CONN_DISABLE_HT;
- fallthrough;
+ conn.mode = IEEE80211_CONN_MODE_LEGACY;
+ conn.bw_limit = IEEE80211_CONN_BW_LIMIT_20;
+ break;
case NL80211_CHAN_WIDTH_20:
- conn_flags |= IEEE80211_CONN_DISABLE_40MHZ;
+ conn.bw_limit = IEEE80211_CONN_BW_LIMIT_40;
fallthrough;
case NL80211_CHAN_WIDTH_40:
- conn_flags |= IEEE80211_CONN_DISABLE_VHT;
+ conn.mode = IEEE80211_CONN_MODE_HT;
break;
default:
break;
@@ -1321,8 +1322,8 @@ ieee80211_mesh_process_chnswitch(struct ieee80211_sub_if_data *sdata,
memset(¶ms, 0, sizeof(params));
err = ieee80211_parse_ch_switch_ie(sdata, elems, sband->band,
- vht_cap_info,
- conn_flags, sdata->vif.addr,
+ vht_cap_info, &conn,
+ sdata->vif.addr,
&csa_ie);
if (err < 0)
return false;
@@ -149,8 +149,7 @@ ieee80211_handle_puncturing_bitmap(struct ieee80211_link_data *link,
if (cfg80211_valid_disable_subchannel_bitmap(&bitmap,
chandef))
break;
- link->u.mgd.conn_flags |=
- ieee80211_chandef_downgrade(chandef);
+ ieee80211_chandef_downgrade(chandef, &link->u.mgd.conn);
*changed |= BSS_CHANGED_BANDWIDTH;
}
@@ -217,77 +216,88 @@ static int ecw2cw(int ecw)
return (1 << ecw) - 1;
}
-static ieee80211_conn_flags_t
-ieee80211_determine_chantype(struct ieee80211_sub_if_data *sdata,
- struct ieee80211_link_data *link,
- ieee80211_conn_flags_t conn_flags,
- struct ieee80211_supported_band *sband,
- struct ieee80211_channel *channel,
- u32 vht_cap_info,
- const struct ieee80211_ht_operation *ht_oper,
- const struct ieee80211_vht_operation *vht_oper,
- const struct ieee80211_he_operation *he_oper,
- const struct ieee80211_eht_operation *eht_oper,
- const struct ieee80211_s1g_oper_ie *s1g_oper,
- struct cfg80211_chan_def *chandef, bool tracking)
+static enum ieee80211_conn_mode
+ieee80211_determine_ap_chan(struct ieee80211_sub_if_data *sdata,
+ struct ieee80211_channel *channel,
+ u32 vht_cap_info,
+ const struct ieee802_11_elems *elems,
+ bool ignore_ht_channel_mismatch,
+ const struct ieee80211_conn_settings *conn,
+ struct cfg80211_chan_def *chandef) /* out */
{
+ const struct ieee80211_ht_operation *ht_oper = elems->ht_operation;
+ const struct ieee80211_vht_operation *vht_oper = elems->vht_operation;
+ const struct ieee80211_he_operation *he_oper = elems->he_operation;
+ const struct ieee80211_eht_operation *eht_oper = elems->eht_operation;
+ struct ieee80211_supported_band *sband =
+ sdata->local->hw.wiphy->bands[channel->band];
+ bool is_6ghz = sband->band == NL80211_BAND_6GHZ;
struct cfg80211_chan_def vht_chandef;
- struct ieee80211_sta_ht_cap sta_ht_cap;
- ieee80211_conn_flags_t ret;
+ bool no_vht = false;
u32 ht_cfreq;
- memset(chandef, 0, sizeof(struct cfg80211_chan_def));
- chandef->chan = channel;
- chandef->width = NL80211_CHAN_WIDTH_20_NOHT;
- chandef->center_freq1 = channel->center_freq;
- chandef->freq1_offset = channel->freq_offset;
+ *chandef = (struct cfg80211_chan_def) {
+ .chan = channel,
+ .width = NL80211_CHAN_WIDTH_20_NOHT,
+ .center_freq1 = channel->center_freq,
+ .freq1_offset = channel->freq_offset,
+ };
- if (channel->band == NL80211_BAND_6GHZ) {
- if (!ieee80211_chandef_he_6ghz_oper(sdata, he_oper, eht_oper,
- chandef)) {
- mlme_dbg(sdata,
- "bad 6 GHz operation, disabling HT/VHT/HE/EHT\n");
- ret = IEEE80211_CONN_DISABLE_HT |
- IEEE80211_CONN_DISABLE_VHT |
- IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT;
- } else {
- ret = 0;
- }
- vht_chandef = *chandef;
- goto out;
- } else if (sband->band == NL80211_BAND_S1GHZ) {
- if (!ieee80211_chandef_s1g_oper(s1g_oper, chandef)) {
+ /* get special S1G case out of the way */
+ if (sband->band == NL80211_BAND_S1GHZ) {
+ if (!ieee80211_chandef_s1g_oper(elems->s1g_oper, chandef)) {
sdata_info(sdata,
"Missing S1G Operation Element? Trying operating == primary\n");
chandef->width = ieee80211_s1g_channel_width(channel);
}
- ret = IEEE80211_CONN_DISABLE_HT | IEEE80211_CONN_DISABLE_40MHZ |
- IEEE80211_CONN_DISABLE_VHT |
- IEEE80211_CONN_DISABLE_80P80MHZ |
- IEEE80211_CONN_DISABLE_160MHZ;
- goto out;
+ return IEEE80211_CONN_MODE_S1G;
}
- memcpy(&sta_ht_cap, &sband->ht_cap, sizeof(sta_ht_cap));
- ieee80211_apply_htcap_overrides(sdata, &sta_ht_cap);
+ /* get special 6 GHz case out of the way */
+ if (is_6ghz) {
+ enum ieee80211_conn_mode mode = IEEE80211_CONN_MODE_EHT;
- if (!ht_oper || !sta_ht_cap.ht_supported) {
- mlme_dbg(sdata, "HT operation missing / HT not supported\n");
- ret = IEEE80211_CONN_DISABLE_HT |
- IEEE80211_CONN_DISABLE_VHT |
- IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT;
- goto out;
+ /* this is an error */
+ if (conn->mode < IEEE80211_CONN_MODE_HE)
+ return IEEE80211_CONN_MODE_LEGACY;
+
+ if (!elems->he_6ghz_capa) {
+ sdata_info(sdata,
+ "HE 6 GHz AP is missing HE 6 GHz band capability\n");
+ return IEEE80211_CONN_MODE_LEGACY;
+ }
+
+ if (!elems->he_cap)
+ return IEEE80211_CONN_MODE_LEGACY;
+
+ if (!eht_oper || !elems->eht_cap) {
+ eht_oper = NULL;
+ mode = IEEE80211_CONN_MODE_HE;
+ }
+
+ if (!ieee80211_chandef_he_6ghz_oper(sdata, he_oper,
+ eht_oper, chandef)) {
+ sdata_info(sdata, "bad HE/EHT 6 GHz operation\n");
+ return IEEE80211_CONN_MODE_LEGACY;
+ }
+
+ return mode;
}
+ /* now we have the progression HT, VHT, ... */
+ if (conn->mode < IEEE80211_CONN_MODE_HT)
+ return IEEE80211_CONN_MODE_LEGACY;
+
+ if (!is_6ghz && (!ht_oper || !elems->ht_cap_elem))
+ return IEEE80211_CONN_MODE_LEGACY;
+
chandef->width = NL80211_CHAN_WIDTH_20;
ht_cfreq = ieee80211_channel_to_frequency(ht_oper->primary_chan,
channel->band);
/* check that channel matches the right operating channel */
- if (!tracking && channel->center_freq != ht_cfreq) {
+ if (!ignore_ht_channel_mismatch && channel->center_freq != ht_cfreq) {
/*
* It's possible that some APs are confused here;
* Netgear WNDR3700 sometimes reports 4 higher than
@@ -299,36 +309,22 @@ ieee80211_determine_chantype(struct ieee80211_sub_if_data *sdata,
"Wrong control channel: center-freq: %d ht-cfreq: %d ht->primary_chan: %d band: %d - Disabling HT\n",
channel->center_freq, ht_cfreq,
ht_oper->primary_chan, channel->band);
- ret = IEEE80211_CONN_DISABLE_HT |
- IEEE80211_CONN_DISABLE_VHT |
- IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT;
- goto out;
+ return IEEE80211_CONN_MODE_LEGACY;
}
- /* check 40 MHz support, if we have it */
- if (sta_ht_cap.cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40) {
- ieee80211_chandef_ht_oper(ht_oper, chandef);
- } else {
- mlme_dbg(sdata, "40 MHz not supported\n");
- /* 40 MHz (and 80 MHz) must be supported for VHT */
- ret = IEEE80211_CONN_DISABLE_VHT;
- /* also mark 40 MHz disabled */
- ret |= IEEE80211_CONN_DISABLE_40MHZ;
- goto out;
- }
+ ieee80211_chandef_ht_oper(ht_oper, chandef);
- if (!vht_oper || !sband->vht_cap.vht_supported) {
- mlme_dbg(sdata, "VHT operation missing / VHT not supported\n");
- ret = IEEE80211_CONN_DISABLE_VHT;
- goto out;
- }
+ if (conn->mode < IEEE80211_CONN_MODE_VHT)
+ return IEEE80211_CONN_MODE_HT;
vht_chandef = *chandef;
- if (!(conn_flags & IEEE80211_CONN_DISABLE_HE) &&
- he_oper &&
- (le32_to_cpu(he_oper->he_oper_params) &
- IEEE80211_HE_OPERATION_VHT_OPER_INFO)) {
+
+ /*
+ * having he_cap/he_oper parsed out implies we're at
+ * least operating as HE STA
+ */
+ if (elems->he_cap && he_oper &&
+ he_oper->he_oper_params & cpu_to_le32(IEEE80211_HE_OPERATION_VHT_OPER_INFO)) {
struct ieee80211_vht_operation he_oper_vht_cap;
/*
@@ -341,52 +337,63 @@ ieee80211_determine_chantype(struct ieee80211_sub_if_data *sdata,
if (!ieee80211_chandef_vht_oper(&sdata->local->hw, vht_cap_info,
&he_oper_vht_cap, ht_oper,
&vht_chandef)) {
- if (!(conn_flags & IEEE80211_CONN_DISABLE_HE))
- sdata_info(sdata,
- "HE AP VHT information is invalid, disabling HE\n");
- ret = IEEE80211_CONN_DISABLE_HE | IEEE80211_CONN_DISABLE_EHT;
- goto out;
+ sdata_info(sdata,
+ "HE AP VHT information is invalid, disabling HE\n");
+ /* this will cause us to re-parse as VHT STA */
+ return IEEE80211_CONN_MODE_VHT;
}
+ } if (!vht_oper || !elems->vht_cap_elem) {
+ if (sband->band == NL80211_BAND_5GHZ) {
+ sdata_info(sdata,
+ "VHT information is missing, disabling VHT\n");
+ return IEEE80211_CONN_MODE_HT;
+ }
+ no_vht = true;
+ } else if (sband->band == NL80211_BAND_2GHZ) {
+ no_vht = true;
} else if (!ieee80211_chandef_vht_oper(&sdata->local->hw,
vht_cap_info,
vht_oper, ht_oper,
&vht_chandef)) {
- if (!(conn_flags & IEEE80211_CONN_DISABLE_VHT))
- sdata_info(sdata,
- "AP VHT information is invalid, disabling VHT\n");
- ret = IEEE80211_CONN_DISABLE_VHT;
- goto out;
- }
-
- if (!cfg80211_chandef_valid(&vht_chandef)) {
- if (!(conn_flags & IEEE80211_CONN_DISABLE_VHT))
- sdata_info(sdata,
- "AP VHT information is invalid, disabling VHT\n");
- ret = IEEE80211_CONN_DISABLE_VHT;
- goto out;
- }
-
- if (cfg80211_chandef_identical(chandef, &vht_chandef)) {
- ret = 0;
- goto out;
+ sdata_info(sdata,
+ "AP VHT information is invalid, disabling VHT\n");
+ return IEEE80211_CONN_MODE_HT;
}
if (!cfg80211_chandef_compatible(chandef, &vht_chandef)) {
- if (!(conn_flags & IEEE80211_CONN_DISABLE_VHT))
- sdata_info(sdata,
- "AP VHT information doesn't match HT, disabling VHT\n");
- ret = IEEE80211_CONN_DISABLE_VHT;
- goto out;
+ sdata_info(sdata,
+ "AP VHT information doesn't match HT, disabling VHT\n");
+ return IEEE80211_CONN_MODE_HT;
}
*chandef = vht_chandef;
+ /* stick to current max mode if we don't have HE */
+ if (conn->mode < IEEE80211_CONN_MODE_HE) {
+ if (no_vht)
+ return IEEE80211_CONN_MODE_HT;
+ return IEEE80211_CONN_MODE_VHT;
+ }
+
+ if (!elems->he_operation || !elems->he_cap) {
+ if (no_vht)
+ return IEEE80211_CONN_MODE_HT;
+ return IEEE80211_CONN_MODE_VHT;
+ }
+
+ /* stick to HE if we don't have EHT */
+ if (conn->mode < IEEE80211_CONN_MODE_EHT)
+ return IEEE80211_CONN_MODE_HE;
+
+ if (!eht_oper || !elems->eht_cap)
+ return IEEE80211_CONN_MODE_HE;
+
/*
* handle the case that the EHT operation indicates that it holds EHT
* operation information (in case that the channel width differs from
* the channel width reported in HT/VHT/HE).
*/
- if (eht_oper && (eht_oper->params & IEEE80211_EHT_OPER_INFO_PRESENT)) {
+ if (eht_oper->params & IEEE80211_EHT_OPER_INFO_PRESENT) {
struct cfg80211_chan_def eht_chandef = *chandef;
ieee80211_chandef_eht_oper((const void *)eht_oper->optional,
@@ -395,199 +402,589 @@ ieee80211_determine_chantype(struct ieee80211_sub_if_data *sdata,
false, &eht_chandef);
if (!cfg80211_chandef_valid(&eht_chandef)) {
- if (!(conn_flags & IEEE80211_CONN_DISABLE_EHT))
- sdata_info(sdata,
- "AP EHT information is invalid, disabling EHT\n");
- ret = IEEE80211_CONN_DISABLE_EHT;
- goto out;
+ sdata_info(sdata,
+ "AP EHT information is invalid, disabling EHT\n");
+ return IEEE80211_CONN_MODE_HE;
}
if (!cfg80211_chandef_compatible(chandef, &eht_chandef)) {
- if (!(conn_flags & IEEE80211_CONN_DISABLE_EHT))
- sdata_info(sdata,
- "AP EHT information is incompatible, disabling EHT\n");
- ret = IEEE80211_CONN_DISABLE_EHT;
- goto out;
+ sdata_info(sdata,
+ "AP EHT information doesn't match HT/VHT/HE, disabling EHT\n");
+ return IEEE80211_CONN_MODE_HE;
}
*chandef = eht_chandef;
}
- ret = 0;
+ return IEEE80211_CONN_MODE_EHT;
+}
+
+static bool
+ieee80211_verify_peer_he_mcs_support(struct ieee80211_sub_if_data *sdata,
+ const struct ieee80211_he_cap_elem *he_cap,
+ const struct ieee80211_he_operation *he_op)
+{
+ struct ieee80211_he_mcs_nss_supp *he_mcs_nss_supp;
+ u16 mcs_80_map_tx, mcs_80_map_rx;
+ u16 ap_min_req_set;
+ int nss;
+
+ if (!he_cap)
+ return false;
+
+ /* mcs_nss is right after he_cap info */
+ he_mcs_nss_supp = (void *)(he_cap + 1);
+
+ mcs_80_map_tx = le16_to_cpu(he_mcs_nss_supp->tx_mcs_80);
+ mcs_80_map_rx = le16_to_cpu(he_mcs_nss_supp->rx_mcs_80);
+
+ /* P802.11-REVme/D0.3
+ * 27.1.1 Introduction to the HE PHY
+ * ...
+ * An HE STA shall support the following features:
+ * ...
+ * Single spatial stream HE-MCSs 0 to 7 (transmit and receive) in all
+ * supported channel widths for HE SU PPDUs
+ */
+ if ((mcs_80_map_tx & 0x3) == IEEE80211_HE_MCS_NOT_SUPPORTED ||
+ (mcs_80_map_rx & 0x3) == IEEE80211_HE_MCS_NOT_SUPPORTED) {
+ sdata_info(sdata,
+ "Missing mandatory rates for 1 Nss, rx 0x%x, tx 0x%x, disable HE\n",
+ mcs_80_map_tx, mcs_80_map_rx);
+ return false;
+ }
+
+ if (!he_op)
+ return true;
+
+ ap_min_req_set = le16_to_cpu(he_op->he_mcs_nss_set);
-out:
/*
- * When tracking the current AP, don't do any further checks if the
- * new chandef is identical to the one we're currently using for the
- * connection. This keeps us from playing ping-pong with regulatory,
- * without it the following can happen (for example):
- * - connect to an AP with 80 MHz, world regdom allows 80 MHz
- * - AP advertises regdom US
- * - CRDA loads regdom US with 80 MHz prohibited (old database)
- * - the code below detects an unsupported channel, downgrades, and
- * we disconnect from the AP in the caller
- * - disconnect causes CRDA to reload world regdomain and the game
- * starts anew.
- * (see https://bugzilla.kernel.org/show_bug.cgi?id=70881)
+ * Apparently iPhone 13 (at least iOS version 15.3.1) sets this to all
+ * zeroes, which is nonsense, and completely inconsistent with itself
+ * (it doesn't have 8 streams). Accept the settings in this case anyway.
+ */
+ if (!ap_min_req_set)
+ return true;
+
+ /* make sure the AP is consistent with itself
*
- * It seems possible that there are still scenarios with CSA or real
- * bandwidth changes where a this could happen, but those cases are
- * less common and wouldn't completely prevent using the AP.
+ * P802.11-REVme/D0.3
+ * 26.17.1 Basic HE BSS operation
+ *
+ * A STA that is operating in an HE BSS shall be able to receive and
+ * transmit at each of the <HE-MCS, NSS> tuple values indicated by the
+ * Basic HE-MCS And NSS Set field of the HE Operation parameter of the
+ * MLME-START.request primitive and shall be able to receive at each of
+ * the <HE-MCS, NSS> tuple values indicated by the Supported HE-MCS and
+ * NSS Set field in the HE Capabilities parameter of the MLMESTART.request
+ * primitive
*/
- if (tracking &&
- cfg80211_chandef_identical(chandef, &link->conf->chandef))
- return ret;
+ for (nss = 8; nss > 0; nss--) {
+ u8 ap_op_val = (ap_min_req_set >> (2 * (nss - 1))) & 3;
+ u8 ap_rx_val;
+ u8 ap_tx_val;
+
+ if (ap_op_val == IEEE80211_HE_MCS_NOT_SUPPORTED)
+ continue;
+
+ ap_rx_val = (mcs_80_map_rx >> (2 * (nss - 1))) & 3;
+ ap_tx_val = (mcs_80_map_tx >> (2 * (nss - 1))) & 3;
- /* don't print the message below for VHT mismatch if VHT is disabled */
- if (ret & IEEE80211_CONN_DISABLE_VHT)
- vht_chandef = *chandef;
+ if (ap_rx_val == IEEE80211_HE_MCS_NOT_SUPPORTED ||
+ ap_tx_val == IEEE80211_HE_MCS_NOT_SUPPORTED ||
+ ap_rx_val < ap_op_val || ap_tx_val < ap_op_val) {
+ sdata_info(sdata,
+ "Invalid rates for %d Nss, rx %d, tx %d oper %d, disable HE\n",
+ nss, ap_rx_val, ap_rx_val, ap_op_val);
+ return false;
+ }
+ }
+
+ return true;
+}
+
+static bool
+ieee80211_verify_sta_he_mcs_support(struct ieee80211_sub_if_data *sdata,
+ struct ieee80211_supported_band *sband,
+ const struct ieee80211_he_operation *he_op)
+{
+ const struct ieee80211_sta_he_cap *sta_he_cap =
+ ieee80211_get_he_iftype_cap_vif(sband, &sdata->vif);
+ u16 ap_min_req_set;
+ int i;
+
+ if (!sta_he_cap || !he_op)
+ return false;
+
+ ap_min_req_set = le16_to_cpu(he_op->he_mcs_nss_set);
/*
- * Ignore the DISABLED flag when we're already connected and only
- * tracking the APs beacon for bandwidth changes - otherwise we
- * might get disconnected here if we connect to an AP, update our
- * regulatory information based on the AP's country IE and the
- * information we have is wrong/outdated and disables the channel
- * that we're actually using for the connection to the AP.
+ * Apparently iPhone 13 (at least iOS version 15.3.1) sets this to all
+ * zeroes, which is nonsense, and completely inconsistent with itself
+ * (it doesn't have 8 streams). Accept the settings in this case anyway.
+ */
+ if (!ap_min_req_set)
+ return true;
+
+ /* Need to go over for 80MHz, 160MHz and for 80+80 */
+ for (i = 0; i < 3; i++) {
+ const struct ieee80211_he_mcs_nss_supp *sta_mcs_nss_supp =
+ &sta_he_cap->he_mcs_nss_supp;
+ u16 sta_mcs_map_rx =
+ le16_to_cpu(((__le16 *)sta_mcs_nss_supp)[2 * i]);
+ u16 sta_mcs_map_tx =
+ le16_to_cpu(((__le16 *)sta_mcs_nss_supp)[2 * i + 1]);
+ u8 nss;
+ bool verified = true;
+
+ /*
+ * For each band there is a maximum of 8 spatial streams
+ * possible. Each of the sta_mcs_map_* is a 16-bit struct built
+ * of 2 bits per NSS (1-8), with the values defined in enum
+ * ieee80211_he_mcs_support. Need to make sure STA TX and RX
+ * capabilities aren't less than the AP's minimum requirements
+ * for this HE BSS per SS.
+ * It is enough to find one such band that meets the reqs.
+ */
+ for (nss = 8; nss > 0; nss--) {
+ u8 sta_rx_val = (sta_mcs_map_rx >> (2 * (nss - 1))) & 3;
+ u8 sta_tx_val = (sta_mcs_map_tx >> (2 * (nss - 1))) & 3;
+ u8 ap_val = (ap_min_req_set >> (2 * (nss - 1))) & 3;
+
+ if (ap_val == IEEE80211_HE_MCS_NOT_SUPPORTED)
+ continue;
+
+ /*
+ * Make sure the HE AP doesn't require MCSs that aren't
+ * supported by the client as required by spec
+ *
+ * P802.11-REVme/D0.3
+ * 26.17.1 Basic HE BSS operation
+ *
+ * An HE STA shall not attempt to join * (MLME-JOIN.request primitive)
+ * a BSS, unless it supports (i.e., is able to both transmit and
+ * receive using) all of the <HE-MCS, NSS> tuples in the basic
+ * HE-MCS and NSS set.
+ */
+ if (sta_rx_val == IEEE80211_HE_MCS_NOT_SUPPORTED ||
+ sta_tx_val == IEEE80211_HE_MCS_NOT_SUPPORTED ||
+ (ap_val > sta_rx_val) || (ap_val > sta_tx_val)) {
+ verified = false;
+ break;
+ }
+ }
+
+ if (verified)
+ return true;
+ }
+
+ /* If here, STA doesn't meet AP's HE min requirements */
+ return false;
+}
+
+static u8
+ieee80211_get_eht_cap_mcs_nss(const struct ieee80211_sta_he_cap *sta_he_cap,
+ const struct ieee80211_sta_eht_cap *sta_eht_cap,
+ unsigned int idx, int bw)
+{
+ u8 he_phy_cap0 = sta_he_cap->he_cap_elem.phy_cap_info[0];
+ u8 eht_phy_cap0 = sta_eht_cap->eht_cap_elem.phy_cap_info[0];
+
+ /* handle us being a 20 MHz-only EHT STA - with four values
+ * for MCS 0-7, 8-9, 10-11, 12-13.
*/
+ if (!(he_phy_cap0 & IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_MASK_ALL))
+ return sta_eht_cap->eht_mcs_nss_supp.only_20mhz.rx_tx_max_nss[idx];
+
+ /* the others have MCS 0-9 together, rather than separately from 0-7 */
+ if (idx > 0)
+ idx--;
+
+ switch (bw) {
+ case 0:
+ return sta_eht_cap->eht_mcs_nss_supp.bw._80.rx_tx_max_nss[idx];
+ case 1:
+ if (!(he_phy_cap0 &
+ (IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G |
+ IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G)))
+ return 0xff; /* pass check */
+ return sta_eht_cap->eht_mcs_nss_supp.bw._160.rx_tx_max_nss[idx];
+ case 2:
+ if (!(eht_phy_cap0 & IEEE80211_EHT_PHY_CAP0_320MHZ_IN_6GHZ))
+ return 0xff; /* pass check */
+ return sta_eht_cap->eht_mcs_nss_supp.bw._320.rx_tx_max_nss[idx];
+ }
+
+ WARN_ON(1);
+ return 0;
+}
+
+static bool
+ieee80211_verify_sta_eht_mcs_support(struct ieee80211_sub_if_data *sdata,
+ struct ieee80211_supported_band *sband,
+ const struct ieee80211_eht_operation *eht_op)
+{
+ const struct ieee80211_sta_he_cap *sta_he_cap =
+ ieee80211_get_he_iftype_cap_vif(sband, &sdata->vif);
+ const struct ieee80211_sta_eht_cap *sta_eht_cap =
+ ieee80211_get_eht_iftype_cap_vif(sband, &sdata->vif);
+ const struct ieee80211_eht_mcs_nss_supp_20mhz_only *req;
+ unsigned int i;
+
+ if (!sta_he_cap || !sta_eht_cap || !eht_op)
+ return false;
+
+ req = &eht_op->basic_mcs_nss;
+
+ for (i = 0; i < ARRAY_SIZE(req->rx_tx_max_nss); i++) {
+ u8 req_rx_nss, req_tx_nss;
+ unsigned int bw;
+
+ req_rx_nss = u8_get_bits(req->rx_tx_max_nss[i],
+ IEEE80211_EHT_MCS_NSS_RX);
+ req_tx_nss = u8_get_bits(req->rx_tx_max_nss[i],
+ IEEE80211_EHT_MCS_NSS_TX);
+
+ for (bw = 0; bw < 3; bw++) {
+ u8 have, have_rx_nss, have_tx_nss;
+
+ have = ieee80211_get_eht_cap_mcs_nss(sta_he_cap,
+ sta_eht_cap,
+ i, bw);
+ have_rx_nss = u8_get_bits(have,
+ IEEE80211_EHT_MCS_NSS_RX);
+ have_tx_nss = u8_get_bits(have,
+ IEEE80211_EHT_MCS_NSS_TX);
+
+ if (req_rx_nss > have_rx_nss ||
+ req_tx_nss > have_tx_nss)
+ return false;
+ }
+ }
+
+ return true;
+}
+
+static const char *ieee80211_conn_mode_str(enum ieee80211_conn_mode mode)
+{
+ static const char *modes[] = {
+ [IEEE80211_CONN_MODE_S1G] = "S1G",
+ [IEEE80211_CONN_MODE_LEGACY] = "legacy",
+ [IEEE80211_CONN_MODE_HT] = "HT",
+ [IEEE80211_CONN_MODE_VHT] = "VHT",
+ [IEEE80211_CONN_MODE_HE] = "HE",
+ [IEEE80211_CONN_MODE_EHT] = "EHT",
+ };
+
+ if (WARN_ON(mode >= ARRAY_SIZE(modes)))
+ return "<out of range>";
+
+ return modes[mode] ?: "<missing string>";
+}
+
+static struct ieee802_11_elems *
+ieee80211_determine_chan_mode(struct ieee80211_sub_if_data *sdata,
+ struct ieee80211_conn_settings *conn,
+ struct cfg80211_bss *cbss, int link_id,
+ struct cfg80211_chan_def *chandef)
+{
+ const struct cfg80211_bss_ies *ies = rcu_dereference(cbss->ies);
+ struct ieee80211_bss *bss = (void *)cbss->priv;
+ struct ieee80211_channel *channel = cbss->channel;
+ struct ieee80211_elems_parse_params parse_params = {
+ .link_id = -1,
+ .from_ap = true,
+ .start = ies->data,
+ .len = ies->len,
+ .mode = conn->mode,
+ };
+ struct ieee802_11_elems *elems;
+ struct ieee80211_supported_band *sband;
+ struct cfg80211_chan_def ap_chandef;
+ enum ieee80211_conn_mode ap_mode;
+ int ret;
+
+again:
+ elems = ieee802_11_parse_elems_full(&parse_params);
+ if (!elems)
+ return ERR_PTR(-ENOMEM);
+
+ ap_mode = ieee80211_determine_ap_chan(sdata, channel, bss->vht_cap_info,
+ elems, false, conn, &ap_chandef);
+
+ mlme_link_id_dbg(sdata, link_id, "determined AP %pM to be %s\n",
+ cbss->bssid, ieee80211_conn_mode_str(ap_mode));
+
+ /* this should be impossible since parsing depends on our mode */
+ if (WARN_ON(ap_mode > conn->mode)) {
+ ret = -EINVAL;
+ goto free;
+ }
+
+ sband = sdata->local->hw.wiphy->bands[channel->band];
+
+ switch (channel->band) {
+ case NL80211_BAND_S1GHZ:
+ if (WARN_ON(ap_mode != IEEE80211_CONN_MODE_S1G)) {
+ ret = -EINVAL;
+ goto free;
+ }
+ return elems;
+ case NL80211_BAND_6GHZ:
+ if (ap_mode < IEEE80211_CONN_MODE_HE ||
+ conn->mode < IEEE80211_CONN_MODE_HE) {
+ sdata_info(sdata,
+ "Rejecting non-HE 6/7 GHz connection");
+ ret = -EINVAL;
+ goto free;
+ }
+ break;
+ default:
+ if (WARN_ON(ap_mode == IEEE80211_CONN_MODE_S1G)) {
+ ret = -EINVAL;
+ goto free;
+ }
+ }
+
+ switch (ap_mode) {
+ case IEEE80211_CONN_MODE_S1G:
+ WARN_ON(1);
+ ret = -EINVAL;
+ goto free;
+ case IEEE80211_CONN_MODE_LEGACY:
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_20;
+ break;
+ case IEEE80211_CONN_MODE_HT:
+ conn->bw_limit = min_t(enum ieee80211_conn_bw_limit,
+ conn->bw_limit,
+ IEEE80211_CONN_BW_LIMIT_40);
+ break;
+ case IEEE80211_CONN_MODE_VHT:
+ case IEEE80211_CONN_MODE_HE:
+ conn->bw_limit = min_t(enum ieee80211_conn_bw_limit,
+ conn->bw_limit,
+ IEEE80211_CONN_BW_LIMIT_160);
+ break;
+ case IEEE80211_CONN_MODE_EHT:
+ conn->bw_limit = min_t(enum ieee80211_conn_bw_limit,
+ conn->bw_limit,
+ IEEE80211_CONN_BW_LIMIT_320);
+ break;
+ }
+
+ conn->mode = ap_mode;
+ *chandef = ap_chandef;
+
while (!cfg80211_chandef_usable(sdata->local->hw.wiphy, chandef,
- tracking ? 0 :
- IEEE80211_CHAN_DISABLED)) {
+ IEEE80211_CHAN_DISABLED)) {
if (WARN_ON(chandef->width == NL80211_CHAN_WIDTH_20_NOHT)) {
- ret = IEEE80211_CONN_DISABLE_HT |
- IEEE80211_CONN_DISABLE_VHT |
- IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT;
- break;
+ ret = -EINVAL;
+ goto free;
}
- ret |= ieee80211_chandef_downgrade(chandef);
+ ieee80211_chandef_downgrade(chandef, conn);
}
- if (!he_oper || !cfg80211_chandef_usable(sdata->wdev.wiphy, chandef,
- IEEE80211_CHAN_NO_HE))
- ret |= IEEE80211_CONN_DISABLE_HE | IEEE80211_CONN_DISABLE_EHT;
+ if (conn->mode >= IEEE80211_CONN_MODE_HE &&
+ !cfg80211_chandef_usable(sdata->wdev.wiphy, chandef,
+ IEEE80211_CHAN_NO_HE))
+ conn->mode = IEEE80211_CONN_MODE_VHT;
- if (!eht_oper || !cfg80211_chandef_usable(sdata->wdev.wiphy, chandef,
- IEEE80211_CHAN_NO_EHT))
- ret |= IEEE80211_CONN_DISABLE_EHT;
+ if (conn->mode >= IEEE80211_CONN_MODE_EHT &&
+ !cfg80211_chandef_usable(sdata->wdev.wiphy, chandef,
+ IEEE80211_CHAN_NO_EHT)) {
+ conn->mode = IEEE80211_CONN_MODE_HE;
+ conn->bw_limit = min_t(enum ieee80211_conn_bw_limit,
+ conn->bw_limit,
+ IEEE80211_CONN_BW_LIMIT_160);
+ }
- if (chandef->width != vht_chandef.width && !tracking)
+ if (chandef->width != ap_chandef.width || ap_mode != conn->mode)
sdata_info(sdata,
- "capabilities/regulatory prevented using AP HT/VHT configuration, downgraded\n");
+ "regulatory prevented using AP config, downgraded\n");
- WARN_ON_ONCE(!cfg80211_chandef_valid(chandef));
- return ret;
+ if (conn->mode >= IEEE80211_CONN_MODE_HE &&
+ (!ieee80211_verify_peer_he_mcs_support(sdata, (void *)elems->he_cap,
+ elems->he_operation) ||
+ !ieee80211_verify_sta_he_mcs_support(sdata, sband,
+ elems->he_operation))) {
+ conn->mode = IEEE80211_CONN_MODE_VHT;
+ sdata_info(sdata, "required MCSes not supported, disabling HE\n");
+ }
+
+ if (conn->mode >= IEEE80211_CONN_MODE_EHT &&
+ !ieee80211_verify_sta_eht_mcs_support(sdata, sband,
+ elems->eht_operation)) {
+ conn->mode = IEEE80211_CONN_MODE_HE;
+ conn->bw_limit = min_t(enum ieee80211_conn_bw_limit,
+ conn->bw_limit,
+ IEEE80211_CONN_BW_LIMIT_160);
+ sdata_info(sdata, "required MCSes not supported, disabling EHT\n");
+ }
+
+ if (conn->mode >= IEEE80211_CONN_MODE_EHT) {
+ const struct ieee80211_eht_operation *eht_oper;
+
+ eht_oper = elems->eht_operation;
+
+ if (WARN_ON_ONCE(!eht_oper)) {
+ ret = -EINVAL;
+ goto free;
+ }
+
+ if (eht_oper->params & IEEE80211_EHT_OPER_INFO_PRESENT &&
+ eht_oper->params & IEEE80211_EHT_OPER_DISABLED_SUBCHANNEL_BITMAP_PRESENT) {
+ const struct ieee80211_eht_operation_info *info =
+ (void *)eht_oper->optional;
+ const u8 *disable_subchannel_bitmap = info->optional;
+ u16 bitmap;
+
+ bitmap = get_unaligned_le16(disable_subchannel_bitmap);
+ if (!cfg80211_valid_disable_subchannel_bitmap(&bitmap,
+ &ap_chandef)) {
+ conn->mode = IEEE80211_CONN_MODE_HE;
+ conn->bw_limit = min_t(enum ieee80211_conn_bw_limit,
+ conn->bw_limit,
+ IEEE80211_CONN_BW_LIMIT_160);
+ sdata_info(sdata,
+ "AP has invalid puncturing, disabling EHT\n");
+ }
+ /* FIXME: store puncturing bitmap */
+ }
+ }
+
+ /* the mode can only decrease, so this must terminate */
+ if (ap_mode != conn->mode)
+ goto again;
+
+ mlme_link_id_dbg(sdata, link_id,
+ "connecting with %s mode, max bandwidth %d MHz\n",
+ ieee80211_conn_mode_str(conn->mode),
+ 20 * (1 << conn->bw_limit));
+
+ if (WARN_ON_ONCE(!cfg80211_chandef_valid(chandef))) {
+ ret = -EINVAL;
+ goto free;
+ }
+
+ return elems;
+free:
+ kfree(elems);
+ return ERR_PTR(ret);
+}
+
+static enum ieee80211_conn_bw_limit
+ieee80211_min_bw_limit_from_chandef(struct cfg80211_chan_def *chandef)
+{
+ switch (chandef->width) {
+ case NL80211_CHAN_WIDTH_20_NOHT:
+ case NL80211_CHAN_WIDTH_20:
+ return IEEE80211_CONN_BW_LIMIT_20;
+ case NL80211_CHAN_WIDTH_40:
+ return IEEE80211_CONN_BW_LIMIT_40;
+ case NL80211_CHAN_WIDTH_80:
+ return IEEE80211_CONN_BW_LIMIT_80;
+ case NL80211_CHAN_WIDTH_80P80:
+ case NL80211_CHAN_WIDTH_160:
+ return IEEE80211_CONN_BW_LIMIT_160;
+ case NL80211_CHAN_WIDTH_320:
+ return IEEE80211_CONN_BW_LIMIT_320;
+ default:
+ WARN(1, "unhandled chandef width %d\n", chandef->width);
+ return IEEE80211_CONN_BW_LIMIT_20;
+ }
}
static int ieee80211_config_bw(struct ieee80211_link_data *link,
struct ieee802_11_elems *elems,
- const u8 *bssid, u64 *changed)
+ u64 *changed)
{
- const struct ieee80211_vht_cap *vht_cap = elems->vht_cap_elem;
- const struct ieee80211_ht_operation *ht_oper = elems->ht_operation;
- const struct ieee80211_vht_operation *vht_oper = elems->vht_operation;
- const struct ieee80211_he_operation *he_oper = elems->he_operation;
- const struct ieee80211_eht_operation *eht_oper = elems->eht_operation;
- const struct ieee80211_s1g_oper_ie *s1g_oper = elems->s1g_oper;
+ struct ieee80211_channel *channel = link->conf->chandef.chan;
struct ieee80211_sub_if_data *sdata = link->sdata;
- struct ieee80211_local *local = sdata->local;
- struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
- struct ieee80211_channel *chan = link->conf->chandef.chan;
- struct ieee80211_supported_band *sband =
- local->hw.wiphy->bands[chan->band];
- struct cfg80211_chan_def chandef;
- u16 ht_opmode;
- ieee80211_conn_flags_t flags;
+ struct cfg80211_chan_def ap_chandef;
+ enum ieee80211_conn_mode ap_mode;
u32 vht_cap_info = 0;
+ u16 ht_opmode;
int ret;
- /* if HT was/is disabled, don't track any bandwidth changes */
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT || !ht_oper)
+ /* don't track any bandwidth changes in legacy mode */
+ if (link->u.mgd.conn.mode == IEEE80211_CONN_MODE_LEGACY)
return 0;
- /* don't check VHT if we associated as non-VHT station */
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT)
- vht_oper = NULL;
+ if (elems->vht_cap_elem)
+ vht_cap_info = le32_to_cpu(elems->vht_cap_elem->vht_cap_info);
- /* don't check HE if we associated as non-HE station */
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE ||
- !ieee80211_get_he_iftype_cap_vif(sband, &sdata->vif)) {
- he_oper = NULL;
- eht_oper = NULL;
+ ap_mode = ieee80211_determine_ap_chan(sdata, channel, vht_cap_info,
+ elems, true, &link->u.mgd.conn,
+ &ap_chandef);
+
+ if (ap_mode != link->u.mgd.conn.mode) {
+ link_info(link,
+ "AP appears to change mode (expected %s, found %s), disconnect\n",
+ ieee80211_conn_mode_str(link->u.mgd.conn.mode),
+ ieee80211_conn_mode_str(ap_mode));
+ return -EINVAL;
}
- /* don't check EHT if we associated as non-EHT station */
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_EHT ||
- !ieee80211_get_eht_iftype_cap_vif(sband, &sdata->vif))
- eht_oper = NULL;
-
/*
- * if bss configuration changed store the new one -
+ * if HT operation mode changed store the new one -
* this may be applicable even if channel is identical
*/
- ht_opmode = le16_to_cpu(ht_oper->operation_mode);
- if (link->conf->ht_operation_mode != ht_opmode) {
- *changed |= BSS_CHANGED_HT;
- link->conf->ht_operation_mode = ht_opmode;
+ if (elems->ht_operation) {
+ ht_opmode = le16_to_cpu(elems->ht_operation->operation_mode);
+ if (link->conf->ht_operation_mode != ht_opmode) {
+ *changed |= BSS_CHANGED_HT;
+ link->conf->ht_operation_mode = ht_opmode;
+ }
}
- if (vht_cap)
- vht_cap_info = le32_to_cpu(vht_cap->vht_cap_info);
-
- /* calculate new channel (type) based on HT/VHT/HE operation IEs */
- flags = ieee80211_determine_chantype(sdata, link,
- link->u.mgd.conn_flags,
- sband, chan, vht_cap_info,
- ht_oper, vht_oper,
- he_oper, eht_oper,
- s1g_oper, &chandef, true);
-
/*
* Downgrade the new channel if we associated with restricted
- * capabilities. For example, if we associated as a 20 MHz STA
- * to a 40 MHz AP (due to regulatory, capabilities or config
- * reasons) then switching to a 40 MHz channel now won't do us
- * any good -- we couldn't use it with the AP.
+ * bandwidth capabilities. For example, if we associated as a
+ * 20 MHz STA to a 40 MHz AP (due to regulatory, capabilities
+ * or config reasons) then switching to a 40 MHz channel now
+ * won't do us any good -- we couldn't use it with the AP.
*/
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_80P80MHZ &&
- chandef.width == NL80211_CHAN_WIDTH_80P80)
- flags |= ieee80211_chandef_downgrade(&chandef);
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_160MHZ &&
- chandef.width == NL80211_CHAN_WIDTH_160)
- flags |= ieee80211_chandef_downgrade(&chandef);
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_40MHZ &&
- chandef.width > NL80211_CHAN_WIDTH_20)
- flags |= ieee80211_chandef_downgrade(&chandef);
+ while (link->u.mgd.conn.bw_limit <
+ ieee80211_min_bw_limit_from_chandef(&ap_chandef))
+ ieee80211_chandef_downgrade(&ap_chandef, NULL);
- if (cfg80211_chandef_identical(&chandef, &link->conf->chandef))
+ if (cfg80211_chandef_identical(&ap_chandef, &link->conf->chandef))
return 0;
link_info(link,
"AP %pM changed bandwidth, new config is %d.%03d MHz, width %d (%d.%03d/%d MHz)\n",
- link->u.mgd.bssid, chandef.chan->center_freq,
- chandef.chan->freq_offset, chandef.width,
- chandef.center_freq1, chandef.freq1_offset,
- chandef.center_freq2);
+ link->u.mgd.bssid, ap_chandef.chan->center_freq,
+ ap_chandef.chan->freq_offset, ap_chandef.width,
+ ap_chandef.center_freq1, ap_chandef.freq1_offset,
+ ap_chandef.center_freq2);
- if (flags != (link->u.mgd.conn_flags &
- (IEEE80211_CONN_DISABLE_HT |
- IEEE80211_CONN_DISABLE_VHT |
- IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT |
- IEEE80211_CONN_DISABLE_40MHZ |
- IEEE80211_CONN_DISABLE_80P80MHZ |
- IEEE80211_CONN_DISABLE_160MHZ |
- IEEE80211_CONN_DISABLE_320MHZ)) ||
- !cfg80211_chandef_valid(&chandef)) {
+ if (!cfg80211_chandef_valid(&ap_chandef)) {
sdata_info(sdata,
- "AP %pM changed caps/bw in a way we can't support (0x%x/0x%x) - disconnect\n",
- link->u.mgd.bssid, flags, ifmgd->flags);
+ "AP %pM changed caps/bw in a way we can't support - disconnect\n",
+ link->u.mgd.bssid);
return -EINVAL;
}
- ret = ieee80211_link_change_bandwidth(link, &chandef, changed);
+ /*
+ * We're tracking the current AP here, so don't do any further checks
+ * here. This keeps us from playing ping-pong with regulatory, without
+ * it the following can happen (for example):
+ * - connect to an AP with 80 MHz, world regdom allows 80 MHz
+ * - AP advertises regdom US
+ * - CRDA loads regdom US with 80 MHz prohibited (old database)
+ * - we detect an unsupported channel and disconnect
+ * - disconnect causes CRDA to reload world regdomain and the game
+ * starts anew.
+ * (see https://bugzilla.kernel.org/show_bug.cgi?id=70881)
+ *
+ * It seems possible that there are still scenarios with CSA or real
+ * bandwidth changes where a this could happen, but those cases are
+ * less common and wouldn't completely prevent using the AP.
+ */
+ ret = ieee80211_link_change_bandwidth(link, &ap_chandef, changed);
if (ret) {
sdata_info(sdata,
"AP %pM changed bandwidth to incompatible one - disconnect\n",
@@ -605,7 +1002,7 @@ static void ieee80211_add_ht_ie(struct ieee80211_sub_if_data *sdata,
struct ieee80211_supported_band *sband,
struct ieee80211_channel *channel,
enum ieee80211_smps_mode smps,
- ieee80211_conn_flags_t conn_flags)
+ const struct ieee80211_conn_settings *conn)
{
u8 *pos;
u32 flags = channel->flags;
@@ -640,7 +1037,7 @@ static void ieee80211_add_ht_ie(struct ieee80211_sub_if_data *sdata,
* capable of 40 MHz -- some broken APs will never fall
* back to trying to transmit in 20 MHz.
*/
- if (conn_flags & IEEE80211_CONN_DISABLE_40MHZ) {
+ if (conn->bw_limit <= IEEE80211_CONN_BW_LIMIT_20) {
cap &= ~IEEE80211_HT_CAP_SUP_WIDTH_20_40;
cap &= ~IEEE80211_HT_CAP_SGI_40;
}
@@ -679,7 +1076,7 @@ static bool ieee80211_add_vht_ie(struct ieee80211_sub_if_data *sdata,
struct sk_buff *skb,
struct ieee80211_supported_band *sband,
struct ieee80211_vht_cap *ap_vht_cap,
- ieee80211_conn_flags_t conn_flags)
+ const struct ieee80211_conn_settings *conn)
{
struct ieee80211_local *local = sdata->local;
u8 *pos;
@@ -696,16 +1093,7 @@ static bool ieee80211_add_vht_ie(struct ieee80211_sub_if_data *sdata,
/* determine capability flags */
cap = vht_cap.cap;
- if (conn_flags & IEEE80211_CONN_DISABLE_80P80MHZ) {
- u32 bw = cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK;
-
- cap &= ~IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK;
- if (bw == IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ ||
- bw == IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ)
- cap |= IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ;
- }
-
- if (conn_flags & IEEE80211_CONN_DISABLE_160MHZ) {
+ if (conn->bw_limit <= IEEE80211_CONN_BW_LIMIT_80) {
cap &= ~IEEE80211_VHT_CAP_SHORT_GI_160;
cap &= ~IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK;
}
@@ -769,7 +1157,7 @@ static void ieee80211_add_he_ie(struct ieee80211_sub_if_data *sdata,
struct sk_buff *skb,
struct ieee80211_supported_band *sband,
enum ieee80211_smps_mode smps_mode,
- ieee80211_conn_flags_t conn_flags)
+ const struct ieee80211_conn_settings *conn)
{
u8 *pos, *pre_he_pos;
const struct ieee80211_sta_he_cap *he_cap;
@@ -787,8 +1175,7 @@ static void ieee80211_add_he_ie(struct ieee80211_sub_if_data *sdata,
he_cap->he_cap_elem.phy_cap_info);
pos = skb_put(skb, he_cap_size);
pre_he_pos = pos;
- pos = ieee80211_ie_build_he_cap(conn_flags,
- pos, he_cap, pos + he_cap_size);
+ pos = ieee80211_ie_build_he_cap(conn, he_cap, pos, pos + he_cap_size);
/* trim excess if any */
skb_trim(skb, skb->len - (pre_he_pos + he_cap_size - pos));
@@ -1126,11 +1513,11 @@ static size_t ieee80211_assoc_link_elems(struct ieee80211_sub_if_data *sdata,
offset);
if (sband->band != NL80211_BAND_6GHZ &&
- !(assoc_data->link[link_id].conn_flags & IEEE80211_CONN_DISABLE_HT)) {
+ assoc_data->link[link_id].conn.mode >= IEEE80211_CONN_MODE_HT) {
ieee80211_add_ht_ie(sdata, skb,
assoc_data->link[link_id].ap_ht_param,
sband, chan, smps_mode,
- assoc_data->link[link_id].conn_flags);
+ &assoc_data->link[link_id].conn);
ADD_PRESENT_ELEM(WLAN_EID_HT_CAPABILITY);
}
@@ -1140,36 +1527,25 @@ static size_t ieee80211_assoc_link_elems(struct ieee80211_sub_if_data *sdata,
offset);
if (sband->band != NL80211_BAND_6GHZ &&
- !(assoc_data->link[link_id].conn_flags & IEEE80211_CONN_DISABLE_VHT)) {
+ assoc_data->link[link_id].conn.mode >= IEEE80211_CONN_MODE_VHT) {
bool mu_mimo_owner =
ieee80211_add_vht_ie(sdata, skb, sband,
&assoc_data->link[link_id].ap_vht_cap,
- assoc_data->link[link_id].conn_flags);
+ &assoc_data->link[link_id].conn);
if (link)
link->conf->mu_mimo_owner = mu_mimo_owner;
ADD_PRESENT_ELEM(WLAN_EID_VHT_CAPABILITY);
}
- /*
- * If AP doesn't support HT, mark HE and EHT as disabled.
- * If on the 5GHz band, make sure it supports VHT.
- */
- if (assoc_data->link[link_id].conn_flags & IEEE80211_CONN_DISABLE_HT ||
- (sband->band == NL80211_BAND_5GHZ &&
- assoc_data->link[link_id].conn_flags & IEEE80211_CONN_DISABLE_VHT))
- assoc_data->link[link_id].conn_flags |=
- IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT;
-
/* if present, add any custom IEs that go before HE */
offset = ieee80211_add_before_he_elems(skb, extra_elems,
extra_elems_len,
offset);
- if (!(assoc_data->link[link_id].conn_flags & IEEE80211_CONN_DISABLE_HE)) {
+ if (assoc_data->link[link_id].conn.mode >= IEEE80211_CONN_MODE_HE) {
ieee80211_add_he_ie(sdata, skb, sband, smps_mode,
- assoc_data->link[link_id].conn_flags);
+ &assoc_data->link[link_id].conn);
ADD_PRESENT_EXT_ELEM(WLAN_EID_EXT_HE_CAPABILITY);
}
@@ -1178,7 +1554,7 @@ static size_t ieee80211_assoc_link_elems(struct ieee80211_sub_if_data *sdata,
* calling ieee80211_assoc_add_ml_elem(), so add this one if
* we're going to put it after the ML element
*/
- if (!(assoc_data->link[link_id].conn_flags & IEEE80211_CONN_DISABLE_EHT))
+ if (assoc_data->link[link_id].conn.mode >= IEEE80211_CONN_MODE_EHT)
ADD_PRESENT_EXT_ELEM(WLAN_EID_EXT_EHT_CAPABILITY);
if (link_id == assoc_data->assoc_link_id)
@@ -1188,7 +1564,7 @@ static size_t ieee80211_assoc_link_elems(struct ieee80211_sub_if_data *sdata,
/* crash if somebody gets it wrong */
present_elems = NULL;
- if (!(assoc_data->link[link_id].conn_flags & IEEE80211_CONN_DISABLE_EHT))
+ if (assoc_data->link[link_id].conn.mode >= IEEE80211_CONN_MODE_EHT)
ieee80211_add_eht_ie(sdata, skb, sband);
if (sband->band == NL80211_BAND_S1GHZ) {
@@ -1199,9 +1575,6 @@ static size_t ieee80211_assoc_link_elems(struct ieee80211_sub_if_data *sdata,
if (iftd && iftd->vendor_elems.data && iftd->vendor_elems.len)
skb_put_data(skb, iftd->vendor_elems.data, iftd->vendor_elems.len);
- if (link)
- link->u.mgd.conn_flags = assoc_data->link[link_id].conn_flags;
-
return offset;
}
@@ -1492,7 +1865,7 @@ static int ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
/* Set MBSSID support for HE AP if needed */
if (ieee80211_hw_check(&local->hw, SUPPORTS_ONLY_HE_MULTI_BSSID) &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE) &&
+ link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_HE &&
ext_capa && ext_capa->datalen >= 3)
ext_capa->data[2] |= WLAN_EXT_CAPA3_MULTI_BSSID_SUPPORT;
@@ -1858,7 +2231,7 @@ ieee80211_sta_process_chanswitch(struct ieee80211_link_data *link,
bss = (void *)cbss->priv;
res = ieee80211_parse_ch_switch_ie(sdata, elems, current_band,
bss->vht_cap_info,
- link->u.mgd.conn_flags,
+ &link->u.mgd.conn,
link->u.mgd.bssid, &csa_ie);
if (!res) {
@@ -3038,8 +3411,9 @@ static void ieee80211_set_disassoc(struct ieee80211_sub_if_data *sdata,
sdata->deflink.u.mgd.tracking_signal_avg = false;
sdata->deflink.u.mgd.disable_wmm_tracking = false;
+ sdata->vif.bss_conf.eht_puncturing = 0;
+
ifmgd->flags = 0;
- sdata->deflink.u.mgd.conn_flags = 0;
for (link_id = 0; link_id < ARRAY_SIZE(sdata->link); link_id++) {
struct ieee80211_link_data *link;
@@ -3502,7 +3876,6 @@ static void ieee80211_destroy_auth_data(struct ieee80211_sub_if_data *sdata,
sta_info_destroy_addr(sdata, auth_data->ap_addr);
/* other links are destroyed */
- sdata->deflink.u.mgd.conn_flags = 0;
eth_zero_addr(sdata->deflink.u.mgd.bssid);
ieee80211_link_info_change_notify(sdata, &sdata->deflink,
BSS_CHANGED_BSSID);
@@ -3540,7 +3913,6 @@ static void ieee80211_destroy_assoc_data(struct ieee80211_sub_if_data *sdata,
del_timer_sync(&sdata->u.mgd.timer);
sta_info_destroy_addr(sdata, assoc_data->ap_addr);
- sdata->deflink.u.mgd.conn_flags = 0;
eth_zero_addr(sdata->deflink.u.mgd.bssid);
ieee80211_link_info_change_notify(sdata, &sdata->deflink,
BSS_CHANGED_BSSID);
@@ -3990,11 +4362,13 @@ static bool ieee80211_assoc_config_link(struct ieee80211_link_data *link,
struct ieee80211_local *local = sdata->local;
unsigned int link_id = link->link_id;
struct ieee80211_elems_parse_params parse_params = {
+ .mode = IEEE80211_CONN_MODE_HIGHEST, // FIXME
.start = elem_start,
.len = elem_len,
.link_id = link_id == assoc_data->assoc_link_id ? -1 : link_id,
.from_ap = true,
};
+ bool is_5ghz = cbss->channel->band == NL80211_BAND_5GHZ;
bool is_6ghz = cbss->channel->band == NL80211_BAND_6GHZ;
bool is_s1g = cbss->channel->band == NL80211_BAND_S1GHZ;
const struct cfg80211_bss_ies *bss_ies = NULL;
@@ -4070,9 +4444,9 @@ static bool ieee80211_assoc_config_link(struct ieee80211_link_data *link,
*/
if (!is_6ghz &&
((assoc_data->wmm && !elems->wmm_param) ||
- (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT) &&
+ (link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_HT &&
(!elems->ht_cap_elem || !elems->ht_operation)) ||
- (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT) &&
+ (link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_VHT &&
(!elems->vht_cap_elem || !elems->vht_operation)))) {
const struct cfg80211_bss_ies *ies;
struct ieee802_11_elems *bss_elems;
@@ -4109,25 +4483,25 @@ static bool ieee80211_assoc_config_link(struct ieee80211_link_data *link,
* have to include the IEs in the (re)association response.
*/
if (!elems->ht_cap_elem && bss_elems->ht_cap_elem &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT)) {
+ link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_HT) {
elems->ht_cap_elem = bss_elems->ht_cap_elem;
sdata_info(sdata,
"AP bug: HT capability missing from AssocResp\n");
}
if (!elems->ht_operation && bss_elems->ht_operation &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT)) {
+ link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_HT) {
elems->ht_operation = bss_elems->ht_operation;
sdata_info(sdata,
"AP bug: HT operation missing from AssocResp\n");
}
if (!elems->vht_cap_elem && bss_elems->vht_cap_elem &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT)) {
+ link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_VHT) {
elems->vht_cap_elem = bss_elems->vht_cap_elem;
sdata_info(sdata,
"AP bug: VHT capa missing from AssocResp\n");
}
if (!elems->vht_operation && bss_elems->vht_operation &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT)) {
+ link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_VHT) {
elems->vht_operation = bss_elems->vht_operation;
sdata_info(sdata,
"AP bug: VHT operation missing from AssocResp\n");
@@ -4140,7 +4514,7 @@ static bool ieee80211_assoc_config_link(struct ieee80211_link_data *link,
* We previously checked these in the beacon/probe response, so
* they should be present here. This is just a safety net.
*/
- if (!is_6ghz && !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT) &&
+ if (!is_6ghz && link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_HT &&
(!elems->wmm_param || !elems->ht_cap_elem || !elems->ht_operation)) {
sdata_info(sdata,
"HT AP is missing WMM params or HT capability/operation\n");
@@ -4148,7 +4522,7 @@ static bool ieee80211_assoc_config_link(struct ieee80211_link_data *link,
goto out;
}
- if (!is_6ghz && !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT) &&
+ if (is_5ghz && link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_VHT &&
(!elems->vht_cap_elem || !elems->vht_operation)) {
sdata_info(sdata,
"VHT AP is missing VHT capability/operation\n");
@@ -4156,36 +4530,20 @@ static bool ieee80211_assoc_config_link(struct ieee80211_link_data *link,
goto out;
}
- if (is_6ghz && !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE) &&
- !elems->he_6ghz_capa) {
- sdata_info(sdata,
- "HE 6 GHz AP is missing HE 6 GHz band capability\n");
- ret = false;
- goto out;
- }
-
if (WARN_ON(!link->conf->chandef.chan)) {
ret = false;
goto out;
}
sband = local->hw.wiphy->bands[link->conf->chandef.chan->band];
- if (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE) &&
- (!elems->he_cap || !elems->he_operation)) {
- sdata_info(sdata,
- "HE AP is missing HE capability/operation\n");
- ret = false;
- goto out;
- }
-
/* Set up internal HT/VHT capabilities */
- if (elems->ht_cap_elem && !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT))
+ if (elems->ht_cap_elem && link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_HT)
ieee80211_ht_cap_ie_to_sta_ht_cap(sdata, sband,
elems->ht_cap_elem,
link_sta);
if (elems->vht_cap_elem &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT)) {
+ link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_VHT) {
const struct ieee80211_vht_cap *bss_vht_cap = NULL;
const struct cfg80211_bss_ies *ies;
@@ -4212,7 +4570,8 @@ static bool ieee80211_assoc_config_link(struct ieee80211_link_data *link,
rcu_read_unlock();
}
- if (elems->he_operation && !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE) &&
+ if (elems->he_operation &&
+ link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_HE &&
elems->he_cap) {
ieee80211_he_cap_ie_to_sta_he_cap(sdata, sband,
elems->he_cap,
@@ -4233,7 +4592,7 @@ static bool ieee80211_assoc_config_link(struct ieee80211_link_data *link,
link_sta, elems);
if (elems->eht_operation && elems->eht_cap &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_EHT)) {
+ link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_EHT) {
ieee80211_eht_cap_ie_to_sta_eht_cap(sdata, sband,
elems->he_cap,
elems->he_cap_len,
@@ -4440,7 +4799,7 @@ static u8 ieee80211_max_rx_chains(struct ieee80211_link_data *link,
bool support_160;
u8 chains = 1;
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT)
+ if (link->u.mgd.conn.mode < IEEE80211_CONN_MODE_HT)
return chains;
ht_cap_elem = ieee80211_bss_get_elem(cbss, WLAN_EID_HT_CAPABILITY);
@@ -4453,7 +4812,7 @@ static u8 ieee80211_max_rx_chains(struct ieee80211_link_data *link,
*/
}
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_VHT)
+ if (link->u.mgd.conn.mode <= IEEE80211_CONN_MODE_VHT)
return chains;
vht_cap_elem = ieee80211_bss_get_elem(cbss, WLAN_EID_VHT_CAPABILITY);
@@ -4472,7 +4831,7 @@ static u8 ieee80211_max_rx_chains(struct ieee80211_link_data *link,
chains = max(chains, nss);
}
- if (link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE)
+ if (link->u.mgd.conn.mode & IEEE80211_CONN_MODE_HE)
return chains;
ies = rcu_dereference(cbss->ies);
@@ -4523,465 +4882,278 @@ static u8 ieee80211_max_rx_chains(struct ieee80211_link_data *link,
return chains;
}
-static bool
-ieee80211_verify_peer_he_mcs_support(struct ieee80211_sub_if_data *sdata,
- const struct ieee80211_he_cap_elem *he_cap,
- const struct ieee80211_he_operation *he_op)
+static void
+ieee80211_determine_our_sta_mode(struct ieee80211_sub_if_data *sdata,
+ struct ieee80211_supported_band *sband,
+ struct cfg80211_assoc_request *req,
+ bool wmm_used, int link_id,
+ struct ieee80211_conn_settings *conn)
{
- struct ieee80211_he_mcs_nss_supp *he_mcs_nss_supp;
- u16 mcs_80_map_tx, mcs_80_map_rx;
- u16 ap_min_req_set;
- int nss;
-
- if (!he_cap)
- return false;
-
- /* mcs_nss is right after he_cap info */
- he_mcs_nss_supp = (void *)(he_cap + 1);
-
- mcs_80_map_tx = le16_to_cpu(he_mcs_nss_supp->tx_mcs_80);
- mcs_80_map_rx = le16_to_cpu(he_mcs_nss_supp->rx_mcs_80);
-
- /* P802.11-REVme/D0.3
- * 27.1.1 Introduction to the HE PHY
- * ...
- * An HE STA shall support the following features:
- * ...
- * Single spatial stream HE-MCSs 0 to 7 (transmit and receive) in all
- * supported channel widths for HE SU PPDUs
- */
- if ((mcs_80_map_tx & 0x3) == IEEE80211_HE_MCS_NOT_SUPPORTED ||
- (mcs_80_map_rx & 0x3) == IEEE80211_HE_MCS_NOT_SUPPORTED) {
- sdata_info(sdata,
- "Missing mandatory rates for 1 Nss, rx 0x%x, tx 0x%x, disable HE\n",
- mcs_80_map_tx, mcs_80_map_rx);
- return false;
+ struct ieee80211_sta_ht_cap sta_ht_cap = sband->ht_cap;
+ bool is_5ghz = sband->band == NL80211_BAND_5GHZ;
+ bool is_6ghz = sband->band == NL80211_BAND_6GHZ;
+ const struct ieee80211_sta_he_cap *he_cap;
+ const struct ieee80211_sta_eht_cap *eht_cap;
+ struct ieee80211_sta_vht_cap vht_cap;
+
+ if (sband->band == NL80211_BAND_S1GHZ) {
+ conn->mode = IEEE80211_CONN_MODE_S1G;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_20;
+ mlme_dbg(sdata, "operating as S1G STA\n");
+ return;
}
- if (!he_op)
- return true;
-
- ap_min_req_set = le16_to_cpu(he_op->he_mcs_nss_set);
-
- /*
- * Apparently iPhone 13 (at least iOS version 15.3.1) sets this to all
- * zeroes, which is nonsense, and completely inconsistent with itself
- * (it doesn't have 8 streams). Accept the settings in this case anyway.
- */
- if (!ap_min_req_set)
- return true;
-
- /* make sure the AP is consistent with itself
- *
- * P802.11-REVme/D0.3
- * 26.17.1 Basic HE BSS operation
- *
- * A STA that is operating in an HE BSS shall be able to receive and
- * transmit at each of the <HE-MCS, NSS> tuple values indicated by the
- * Basic HE-MCS And NSS Set field of the HE Operation parameter of the
- * MLME-START.request primitive and shall be able to receive at each of
- * the <HE-MCS, NSS> tuple values indicated by the Supported HE-MCS and
- * NSS Set field in the HE Capabilities parameter of the MLMESTART.request
- * primitive
- */
- for (nss = 8; nss > 0; nss--) {
- u8 ap_op_val = (ap_min_req_set >> (2 * (nss - 1))) & 3;
- u8 ap_rx_val;
- u8 ap_tx_val;
-
- if (ap_op_val == IEEE80211_HE_MCS_NOT_SUPPORTED)
- continue;
+ conn->mode = IEEE80211_CONN_MODE_LEGACY;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_20;
- ap_rx_val = (mcs_80_map_rx >> (2 * (nss - 1))) & 3;
- ap_tx_val = (mcs_80_map_tx >> (2 * (nss - 1))) & 3;
+ ieee80211_apply_htcap_overrides(sdata, &sta_ht_cap);
- if (ap_rx_val == IEEE80211_HE_MCS_NOT_SUPPORTED ||
- ap_tx_val == IEEE80211_HE_MCS_NOT_SUPPORTED ||
- ap_rx_val < ap_op_val || ap_tx_val < ap_op_val) {
- sdata_info(sdata,
- "Invalid rates for %d Nss, rx %d, tx %d oper %d, disable HE\n",
- nss, ap_rx_val, ap_rx_val, ap_op_val);
- return false;
- }
+ if (req && req->flags & ASSOC_REQ_DISABLE_HT) {
+ mlme_link_id_dbg(sdata, link_id,
+ "HT disabled by flag, limiting to legacy\n");
+ goto out;
}
- return true;
-}
-
-static bool
-ieee80211_verify_sta_he_mcs_support(struct ieee80211_sub_if_data *sdata,
- struct ieee80211_supported_band *sband,
- const struct ieee80211_he_operation *he_op)
-{
- const struct ieee80211_sta_he_cap *sta_he_cap =
- ieee80211_get_he_iftype_cap_vif(sband, &sdata->vif);
- u16 ap_min_req_set;
- int i;
-
- if (!sta_he_cap || !he_op)
- return false;
-
- ap_min_req_set = le16_to_cpu(he_op->he_mcs_nss_set);
-
- /*
- * Apparently iPhone 13 (at least iOS version 15.3.1) sets this to all
- * zeroes, which is nonsense, and completely inconsistent with itself
- * (it doesn't have 8 streams). Accept the settings in this case anyway.
- */
- if (!ap_min_req_set)
- return true;
-
- /* Need to go over for 80MHz, 160MHz and for 80+80 */
- for (i = 0; i < 3; i++) {
- const struct ieee80211_he_mcs_nss_supp *sta_mcs_nss_supp =
- &sta_he_cap->he_mcs_nss_supp;
- u16 sta_mcs_map_rx =
- le16_to_cpu(((__le16 *)sta_mcs_nss_supp)[2 * i]);
- u16 sta_mcs_map_tx =
- le16_to_cpu(((__le16 *)sta_mcs_nss_supp)[2 * i + 1]);
- u8 nss;
- bool verified = true;
-
- /*
- * For each band there is a maximum of 8 spatial streams
- * possible. Each of the sta_mcs_map_* is a 16-bit struct built
- * of 2 bits per NSS (1-8), with the values defined in enum
- * ieee80211_he_mcs_support. Need to make sure STA TX and RX
- * capabilities aren't less than the AP's minimum requirements
- * for this HE BSS per SS.
- * It is enough to find one such band that meets the reqs.
- */
- for (nss = 8; nss > 0; nss--) {
- u8 sta_rx_val = (sta_mcs_map_rx >> (2 * (nss - 1))) & 3;
- u8 sta_tx_val = (sta_mcs_map_tx >> (2 * (nss - 1))) & 3;
- u8 ap_val = (ap_min_req_set >> (2 * (nss - 1))) & 3;
+ if (!wmm_used) {
+ mlme_dbg(sdata, "WMM/QoS not supported, limiting to legacy\n");
+ goto out;
+ }
- if (ap_val == IEEE80211_HE_MCS_NOT_SUPPORTED)
- continue;
+ if (req) {
+ unsigned int i;
- /*
- * Make sure the HE AP doesn't require MCSs that aren't
- * supported by the client as required by spec
- *
- * P802.11-REVme/D0.3
- * 26.17.1 Basic HE BSS operation
- *
- * An HE STA shall not attempt to join * (MLME-JOIN.request primitive)
- * a BSS, unless it supports (i.e., is able to both transmit and
- * receive using) all of the <HE-MCS, NSS> tuples in the basic
- * HE-MCS and NSS set.
- */
- if (sta_rx_val == IEEE80211_HE_MCS_NOT_SUPPORTED ||
- sta_tx_val == IEEE80211_HE_MCS_NOT_SUPPORTED ||
- (ap_val > sta_rx_val) || (ap_val > sta_tx_val)) {
- verified = false;
- break;
+ for (i = 0; i < req->crypto.n_ciphers_pairwise; i++) {
+ if (req->crypto.ciphers_pairwise[i] == WLAN_CIPHER_SUITE_WEP40 ||
+ req->crypto.ciphers_pairwise[i] == WLAN_CIPHER_SUITE_TKIP ||
+ req->crypto.ciphers_pairwise[i] == WLAN_CIPHER_SUITE_WEP104) {
+ netdev_info(sdata->dev,
+ "WEP/TKIP use, limiting to legacy\n");
+ goto out;
}
}
+ }
- if (verified)
- return true;
+ if (!sta_ht_cap.ht_supported && !is_6ghz) {
+ mlme_dbg(sdata,
+ "HT not supported (and not on 6 GHz), limiting to legacy\n");
+ goto out;
}
- /* If here, STA doesn't meet AP's HE min requirements */
- return false;
-}
-
-static u8
-ieee80211_get_eht_cap_mcs_nss(const struct ieee80211_sta_he_cap *sta_he_cap,
- const struct ieee80211_sta_eht_cap *sta_eht_cap,
- unsigned int idx, int bw)
-{
- u8 he_phy_cap0 = sta_he_cap->he_cap_elem.phy_cap_info[0];
- u8 eht_phy_cap0 = sta_eht_cap->eht_cap_elem.phy_cap_info[0];
-
- /* handle us being a 20 MHz-only EHT STA - with four values
- * for MCS 0-7, 8-9, 10-11, 12-13.
- */
- if (!(he_phy_cap0 & IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_MASK_ALL))
- return sta_eht_cap->eht_mcs_nss_supp.only_20mhz.rx_tx_max_nss[idx];
-
- /* the others have MCS 0-9 together, rather than separately from 0-7 */
- if (idx > 0)
- idx--;
-
- switch (bw) {
- case 0:
- return sta_eht_cap->eht_mcs_nss_supp.bw._80.rx_tx_max_nss[idx];
- case 1:
- if (!(he_phy_cap0 &
- (IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G |
- IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G)))
- return 0xff; /* pass check */
- return sta_eht_cap->eht_mcs_nss_supp.bw._160.rx_tx_max_nss[idx];
- case 2:
- if (!(eht_phy_cap0 & IEEE80211_EHT_PHY_CAP0_320MHZ_IN_6GHZ))
- return 0xff; /* pass check */
- return sta_eht_cap->eht_mcs_nss_supp.bw._320.rx_tx_max_nss[idx];
+ /* HT is fine */
+ conn->mode = IEEE80211_CONN_MODE_HT;
+ conn->bw_limit = sta_ht_cap.cap & IEEE80211_HT_CAP_SUP_WIDTH_20_40 ?
+ IEEE80211_CONN_BW_LIMIT_40 :
+ IEEE80211_CONN_BW_LIMIT_20;
+
+ memcpy(&vht_cap, &sband->vht_cap, sizeof(vht_cap));
+ ieee80211_apply_vhtcap_overrides(sdata, &vht_cap);
+
+ if (vht_cap.vht_supported && is_5ghz) {
+ bool have_80mhz = false;
+ unsigned int i;
+
+ if (conn->bw_limit == IEEE80211_CONN_BW_LIMIT_20) {
+ mlme_link_id_dbg(sdata, link_id,
+ "no 40 MHz support on 5 GHz, limiting to HT\n");
+ goto out;
+ }
+
+ /* Allow VHT if at least one channel on the sband supports 80 MHz */
+ for (i = 0; i < sband->n_channels; i++) {
+ if (sband->channels[i].flags & (IEEE80211_CHAN_DISABLED |
+ IEEE80211_CHAN_NO_80MHZ))
+ continue;
+
+ have_80mhz = true;
+ break;
+ }
+
+ if (!have_80mhz) {
+ mlme_link_id_dbg(sdata, link_id,
+ "no 80 MHz channel support on 5 GHz, limiting to HT\n");
+ goto out;
+ }
+ } else if (is_5ghz) { /* !vht_supported but on 5 GHz */
+ mlme_link_id_dbg(sdata, link_id,
+ "no VHT support on 5 GHz, limiting to HT\n");
+ goto out;
}
- WARN_ON(1);
- return 0;
-}
-
-static bool
-ieee80211_verify_sta_eht_mcs_support(struct ieee80211_sub_if_data *sdata,
- struct ieee80211_supported_band *sband,
- const struct ieee80211_eht_operation *eht_op)
-{
- const struct ieee80211_sta_he_cap *sta_he_cap =
- ieee80211_get_he_iftype_cap_vif(sband, &sdata->vif);
- const struct ieee80211_sta_eht_cap *sta_eht_cap =
- ieee80211_get_eht_iftype_cap_vif(sband, &sdata->vif);
- const struct ieee80211_eht_mcs_nss_supp_20mhz_only *req;
- unsigned int i;
-
- if (!sta_he_cap || !sta_eht_cap || !eht_op)
- return false;
-
- req = &eht_op->basic_mcs_nss;
-
- for (i = 0; i < ARRAY_SIZE(req->rx_tx_max_nss); i++) {
- u8 req_rx_nss, req_tx_nss;
- unsigned int bw;
-
- req_rx_nss = u8_get_bits(req->rx_tx_max_nss[i],
- IEEE80211_EHT_MCS_NSS_RX);
- req_tx_nss = u8_get_bits(req->rx_tx_max_nss[i],
- IEEE80211_EHT_MCS_NSS_TX);
-
- for (bw = 0; bw < 3; bw++) {
- u8 have, have_rx_nss, have_tx_nss;
-
- have = ieee80211_get_eht_cap_mcs_nss(sta_he_cap,
- sta_eht_cap,
- i, bw);
- have_rx_nss = u8_get_bits(have,
- IEEE80211_EHT_MCS_NSS_RX);
- have_tx_nss = u8_get_bits(have,
- IEEE80211_EHT_MCS_NSS_TX);
-
- if (req_rx_nss > have_rx_nss ||
- req_tx_nss > have_tx_nss)
- return false;
+ if (req && req->flags & ASSOC_REQ_DISABLE_VHT) {
+ mlme_link_id_dbg(sdata, link_id,
+ "VHT disabled by flag, limiting to HT\n");
+ goto out;
+ }
+
+ /* VHT - if we have - is fine, including 80 MHz, check 160 below again */
+ conn->mode = IEEE80211_CONN_MODE_VHT;
+ if (sband->band != NL80211_BAND_2GHZ)
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_160;
+
+ if (is_5ghz &&
+ !(vht_cap.cap & (IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ |
+ IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ))) {
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_80;
+ mlme_link_id_dbg(sdata, link_id,
+ "no VHT 160 MHz capability on 5 GHz, limiting to 80 MHz");
+ }
+
+ if (req && req->flags & ASSOC_REQ_DISABLE_HE) {
+ mlme_dbg(sdata, "HE disabled by flag, limiting to VHT\n");
+ goto out;
+ }
+
+ he_cap = ieee80211_get_he_iftype_cap_vif(sband, &sdata->vif);
+ if (!he_cap) {
+ WARN_ON(is_6ghz);
+ mlme_link_id_dbg(sdata, link_id,
+ "no HE support, limiting to VHT\n");
+ goto out;
+ }
+
+ /* so we have HE */
+ conn->mode = IEEE80211_CONN_MODE_HE;
+
+ /* check bandwidth */
+ switch (sband->band) {
+ default:
+ case NL80211_BAND_2GHZ:
+ if (he_cap->he_cap_elem.phy_cap_info[0] &
+ IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_IN_2G)
+ break;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_20;
+ mlme_link_id_dbg(sdata, link_id,
+ "no 40 MHz HE cap in 2.4 GHz, limiting to 20 MHz\n");
+ break;
+ case NL80211_BAND_5GHZ:
+ if (!(he_cap->he_cap_elem.phy_cap_info[0] &
+ IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G)) {
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_20;
+ mlme_link_id_dbg(sdata, link_id,
+ "no 40/80 MHz HE cap in 5 GHz, limiting to 20 MHz\n");
+ break;
+ }
+ if (!(he_cap->he_cap_elem.phy_cap_info[0] &
+ IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G)) {
+ conn->bw_limit = min_t(enum ieee80211_conn_bw_limit,
+ conn->bw_limit,
+ IEEE80211_CONN_BW_LIMIT_80);
+ mlme_link_id_dbg(sdata, link_id,
+ "no 160 MHz HE cap in 5 GHz, limiting to 80 MHz\n");
}
+ break;
+ case NL80211_BAND_6GHZ:
+ if (he_cap->he_cap_elem.phy_cap_info[0] &
+ IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G)
+ break;
+ conn->bw_limit = min_t(enum ieee80211_conn_bw_limit,
+ conn->bw_limit,
+ IEEE80211_CONN_BW_LIMIT_80);
+ mlme_link_id_dbg(sdata, link_id,
+ "no 160 MHz HE cap in 6 GHz, limiting to 80 MHz\n");
+ break;
+ }
+
+ if (req && req->flags & ASSOC_REQ_DISABLE_EHT) {
+ mlme_dbg(sdata, "EHT disabled by flag, limiting to HE\n");
+ goto out;
+ }
+
+ eht_cap = ieee80211_get_eht_iftype_cap_vif(sband, &sdata->vif);
+ if (!eht_cap) {
+ mlme_link_id_dbg(sdata, link_id,
+ "no EHT support, limiting to HE\n");
+ goto out;
+ }
+
+ /* we have EHT */
+ if (req && req->flags & ASSOC_REQ_DISABLE_EHT) {
+ mlme_dbg(sdata, "EHT disabled by flag, limiting to HE\n");
+ goto out;
}
- return true;
+ conn->mode = IEEE80211_CONN_MODE_EHT;
+
+ /* check bandwidth */
+ if (is_6ghz &&
+ eht_cap->eht_cap_elem.phy_cap_info[0] & IEEE80211_EHT_PHY_CAP0_320MHZ_IN_6GHZ)
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_320;
+ else if (is_6ghz)
+ mlme_link_id_dbg(sdata, link_id,
+ "no EHT 320 MHz cap in 6 GHz, limiting to 160 MHz\n");
+
+out:
+ mlme_link_id_dbg(sdata, link_id,
+ "determined local STA to be %s, BW limited to %d MHz\n",
+ ieee80211_conn_mode_str(conn->mode),
+ 20 * (1 << conn->bw_limit));
}
static int ieee80211_prep_channel(struct ieee80211_sub_if_data *sdata,
struct ieee80211_link_data *link,
- struct cfg80211_bss *cbss,
- bool mlo,
- ieee80211_conn_flags_t *conn_flags)
+ int link_id,
+ struct cfg80211_bss *cbss, bool mlo,
+ struct ieee80211_conn_settings *conn)
{
struct ieee80211_local *local = sdata->local;
- const struct ieee80211_ht_cap *ht_cap = NULL;
- const struct ieee80211_ht_operation *ht_oper = NULL;
- const struct ieee80211_vht_operation *vht_oper = NULL;
- const struct ieee80211_he_operation *he_oper = NULL;
- const struct ieee80211_eht_operation *eht_oper = NULL;
- const struct ieee80211_s1g_oper_ie *s1g_oper = NULL;
- struct ieee80211_supported_band *sband;
struct cfg80211_chan_def chandef;
bool is_6ghz = cbss->channel->band == NL80211_BAND_6GHZ;
- bool is_5ghz = cbss->channel->band == NL80211_BAND_5GHZ;
- bool supports_mlo = false;
- struct ieee80211_bss *bss = (void *)cbss->priv;
- struct ieee80211_elems_parse_params parse_params = {
- .link_id = -1,
- .from_ap = true,
- };
struct ieee802_11_elems *elems;
- const struct cfg80211_bss_ies *ies;
int ret;
u32 i;
- bool have_80mhz;
lockdep_assert_wiphy(local->hw.wiphy);
rcu_read_lock();
+ elems = ieee80211_determine_chan_mode(sdata, conn, cbss, link_id,
+ &chandef);
- ies = rcu_dereference(cbss->ies);
- parse_params.start = ies->data;
- parse_params.len = ies->len;
- elems = ieee802_11_parse_elems_full(&parse_params);
- if (!elems) {
+ if (IS_ERR(elems)) {
rcu_read_unlock();
- return -ENOMEM;
+ return PTR_ERR(elems);
}
- sband = local->hw.wiphy->bands[cbss->channel->band];
-
- *conn_flags &= ~(IEEE80211_CONN_DISABLE_40MHZ |
- IEEE80211_CONN_DISABLE_80P80MHZ |
- IEEE80211_CONN_DISABLE_160MHZ);
-
- /* disable HT/VHT/HE if we don't support them */
- if (!sband->ht_cap.ht_supported && !is_6ghz) {
- mlme_dbg(sdata, "HT not supported, disabling HT/VHT/HE/EHT\n");
- *conn_flags |= IEEE80211_CONN_DISABLE_HT;
- *conn_flags |= IEEE80211_CONN_DISABLE_VHT;
- *conn_flags |= IEEE80211_CONN_DISABLE_HE;
- *conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- }
-
- if (!sband->vht_cap.vht_supported && is_5ghz) {
- mlme_dbg(sdata, "VHT not supported, disabling VHT/HE/EHT\n");
- *conn_flags |= IEEE80211_CONN_DISABLE_VHT;
- *conn_flags |= IEEE80211_CONN_DISABLE_HE;
- *conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- }
-
- if (!ieee80211_get_he_iftype_cap_vif(sband, &sdata->vif)) {
- mlme_dbg(sdata, "HE not supported, disabling HE and EHT\n");
- *conn_flags |= IEEE80211_CONN_DISABLE_HE;
- *conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- }
-
- if (!ieee80211_get_eht_iftype_cap_vif(sband, &sdata->vif)) {
- mlme_dbg(sdata, "EHT not supported, disabling EHT\n");
- *conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- }
-
- if (!(*conn_flags & IEEE80211_CONN_DISABLE_HT) && !is_6ghz) {
- ht_oper = elems->ht_operation;
- ht_cap = elems->ht_cap_elem;
-
- if (!ht_cap) {
- *conn_flags |= IEEE80211_CONN_DISABLE_HT;
- ht_oper = NULL;
- }
- }
-
- if (!(*conn_flags & IEEE80211_CONN_DISABLE_VHT) && !is_6ghz) {
- vht_oper = elems->vht_operation;
- if (vht_oper && !ht_oper) {
- vht_oper = NULL;
- sdata_info(sdata,
- "AP advertised VHT without HT, disabling HT/VHT/HE\n");
- *conn_flags |= IEEE80211_CONN_DISABLE_HT;
- *conn_flags |= IEEE80211_CONN_DISABLE_VHT;
- *conn_flags |= IEEE80211_CONN_DISABLE_HE;
- *conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- }
-
- if (!elems->vht_cap_elem) {
- *conn_flags |= IEEE80211_CONN_DISABLE_VHT;
- vht_oper = NULL;
- }
+ if (mlo && !elems->ml_basic) {
+ sdata_info(sdata, "Rejecting MLO as it is not supported by AP\n");
+ rcu_read_unlock();
+ return -EINVAL;
}
- if (!(*conn_flags & IEEE80211_CONN_DISABLE_HE)) {
- he_oper = elems->he_operation;
-
- if (link && is_6ghz) {
- struct ieee80211_bss_conf *bss_conf;
- u8 j = 0;
+ if (link && is_6ghz && conn->mode >= IEEE80211_CONN_MODE_HE) {
+ struct ieee80211_bss_conf *bss_conf;
+ u8 j = 0;
- bss_conf = link->conf;
+ bss_conf = link->conf;
- if (elems->pwr_constr_elem)
- bss_conf->pwr_reduction = *elems->pwr_constr_elem;
+ if (elems->pwr_constr_elem)
+ bss_conf->pwr_reduction = *elems->pwr_constr_elem;
- BUILD_BUG_ON(ARRAY_SIZE(bss_conf->tx_pwr_env) !=
- ARRAY_SIZE(elems->tx_pwr_env));
+ BUILD_BUG_ON(ARRAY_SIZE(bss_conf->tx_pwr_env) !=
+ ARRAY_SIZE(elems->tx_pwr_env));
- for (i = 0; i < elems->tx_pwr_env_num; i++) {
- if (elems->tx_pwr_env_len[i] >
- sizeof(bss_conf->tx_pwr_env[j]))
- continue;
+ for (i = 0; i < elems->tx_pwr_env_num; i++) {
+ if (elems->tx_pwr_env_len[i] > sizeof(bss_conf->tx_pwr_env[j]))
+ continue;
- bss_conf->tx_pwr_env_num++;
- memcpy(&bss_conf->tx_pwr_env[j], elems->tx_pwr_env[i],
- elems->tx_pwr_env_len[i]);
- j++;
- }
+ bss_conf->tx_pwr_env_num++;
+ memcpy(&bss_conf->tx_pwr_env[j], elems->tx_pwr_env[i],
+ elems->tx_pwr_env_len[i]);
+ j++;
}
-
- if (!ieee80211_verify_peer_he_mcs_support(sdata,
- (void *)elems->he_cap,
- he_oper) ||
- !ieee80211_verify_sta_he_mcs_support(sdata, sband, he_oper))
- *conn_flags |= IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT;
}
-
- /*
- * EHT requires HE to be supported as well. Specifically for 6 GHz
- * channels, the operation channel information can only be deduced from
- * both the 6 GHz operation information (from the HE operation IE) and
- * EHT operation.
- */
- if (!(*conn_flags &
- (IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT)) &&
- he_oper) {
- eht_oper = elems->eht_operation;
-
- if (!ieee80211_verify_sta_eht_mcs_support(sdata, sband, eht_oper))
- *conn_flags |= IEEE80211_CONN_DISABLE_EHT;
-
- supports_mlo = elems->ml_basic;
- }
-
- /* Allow VHT if at least one channel on the sband supports 80 MHz */
- have_80mhz = false;
- for (i = 0; i < sband->n_channels; i++) {
- if (sband->channels[i].flags & (IEEE80211_CHAN_DISABLED |
- IEEE80211_CHAN_NO_80MHZ))
- continue;
-
- have_80mhz = true;
- break;
- }
-
- if (!have_80mhz) {
- sdata_info(sdata, "80 MHz not supported, disabling VHT\n");
- *conn_flags |= IEEE80211_CONN_DISABLE_VHT;
- }
-
- if (sband->band == NL80211_BAND_S1GHZ) {
- s1g_oper = elems->s1g_oper;
- if (!s1g_oper)
- sdata_info(sdata,
- "AP missing S1G operation element?\n");
- }
-
- *conn_flags |=
- ieee80211_determine_chantype(sdata, link, *conn_flags,
- sband,
- cbss->channel,
- bss->vht_cap_info,
- ht_oper, vht_oper,
- he_oper, eht_oper,
- s1g_oper,
- &chandef, false);
-
- if (link)
- link->needed_rx_chains =
- min(ieee80211_max_rx_chains(link, cbss),
- local->rx_chains);
-
rcu_read_unlock();
/* the element data was RCU protected so no longer valid anyway */
kfree(elems);
elems = NULL;
- if (*conn_flags & IEEE80211_CONN_DISABLE_HE && is_6ghz) {
- sdata_info(sdata, "Rejecting non-HE 6/7 GHz connection");
- return -EINVAL;
- }
-
- if (mlo && !supports_mlo) {
- sdata_info(sdata, "Rejecting MLO as it is not supported by AP\n");
- return -EINVAL;
- }
-
if (!link)
return 0;
+ rcu_read_lock();
+ link->needed_rx_chains = min(ieee80211_max_rx_chains(link, cbss),
+ local->rx_chains);
+ rcu_read_unlock();
+
/* will change later if needed */
link->smps_mode = IEEE80211_SMPS_OFF;
@@ -4996,15 +5168,14 @@ static int ieee80211_prep_channel(struct ieee80211_sub_if_data *sdata,
/* don't downgrade for 5 and 10 MHz channels, though. */
if (chandef.width == NL80211_CHAN_WIDTH_5 ||
chandef.width == NL80211_CHAN_WIDTH_10)
- goto out;
+ return ret;
while (ret && chandef.width != NL80211_CHAN_WIDTH_20_NOHT) {
- *conn_flags |=
- ieee80211_chandef_downgrade(&chandef);
+ ieee80211_chandef_downgrade(&chandef, conn);
ret = ieee80211_link_use_channel(link, &chandef,
IEEE80211_CHANCTX_SHARED);
}
- out:
+
return ret;
}
@@ -5128,8 +5299,10 @@ static bool ieee80211_assoc_success(struct ieee80211_sub_if_data *sdata,
link->conf->dtim_period = link->u.mgd.dtim_period ?: 1;
if (link_id != assoc_data->assoc_link_id) {
- err = ieee80211_prep_channel(sdata, link, cbss, true,
- &link->u.mgd.conn_flags);
+ link->u.mgd.conn = assoc_data->link[link_id].conn;
+
+ err = ieee80211_prep_channel(sdata, link, link_id, cbss,
+ true, &link->u.mgd.conn);
if (err) {
link_info(link, "prep_channel failed\n");
goto out_err;
@@ -5222,6 +5395,7 @@ static void ieee80211_rx_mgmt_assoc_resp(struct ieee80211_sub_if_data *sdata,
struct ieee80211_mgd_assoc_data *assoc_data = ifmgd->assoc_data;
u16 capab_info, status_code, aid;
struct ieee80211_elems_parse_params parse_params = {
+ .mode = IEEE80211_CONN_MODE_HIGHEST, // FIXME
.bss = NULL,
.link_id = -1,
.from_ap = true,
@@ -6046,6 +6220,7 @@ static void ieee80211_rx_mgmt_beacon(struct ieee80211_link_data *link,
u8 *bssid, *variable = mgmt->u.beacon.variable;
u8 deauth_buf[IEEE80211_DEAUTH_FRAME_LEN];
struct ieee80211_elems_parse_params parse_params = {
+ .mode = IEEE80211_CONN_MODE_HIGHEST, // FIXME
.link_id = -1,
.from_ap = true,
};
@@ -6300,10 +6475,7 @@ static void ieee80211_rx_mgmt_beacon(struct ieee80211_link_data *link,
changed |= ieee80211_recalc_twt_req(sdata, sband, link, link_sta, elems);
- if (ieee80211_config_bw(link, elems, bssid, &changed)) {
- sdata_info(sdata,
- "failed to follow AP %pM bandwidth change, disconnect\n",
- bssid);
+ if (ieee80211_config_bw(link, elems, &changed)) {
ieee80211_set_disassoc(sdata, IEEE80211_STYPE_DEAUTH,
WLAN_REASON_DEAUTH_LEAVING,
true, deauth_buf);
@@ -6326,7 +6498,7 @@ static void ieee80211_rx_mgmt_beacon(struct ieee80211_link_data *link,
elems->cisco_dtpc_elem);
if (elems->eht_operation &&
- !(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_EHT)) {
+ link->u.mgd.conn.mode >= IEEE80211_CONN_MODE_EHT) {
if (!ieee80211_config_puncturing(link, elems->eht_operation,
&changed)) {
ieee80211_set_disassoc(sdata, IEEE80211_STYPE_DEAUTH,
@@ -6996,7 +7168,6 @@ void ieee80211_mgd_setup_link(struct ieee80211_link_data *link)
unsigned int link_id = link->link_id;
link->u.mgd.p2p_noa_index = -1;
- link->u.mgd.conn_flags = 0;
link->conf->bssid = link->u.mgd.bssid;
wiphy_work_init(&link->u.mgd.request_smps_work,
@@ -7035,6 +7206,7 @@ void ieee80211_mlme_notify_scan_completed(struct ieee80211_local *local)
static int ieee80211_prep_connection(struct ieee80211_sub_if_data *sdata,
struct cfg80211_bss *cbss, s8 link_id,
const u8 *ap_mld_addr, bool assoc,
+ struct ieee80211_conn_settings *conn,
bool override)
{
struct ieee80211_local *local = sdata->local;
@@ -7166,13 +7338,22 @@ static int ieee80211_prep_connection(struct ieee80211_sub_if_data *sdata,
}
if (new_sta || override) {
- err = ieee80211_prep_channel(sdata, link, cbss, mlo,
- &link->u.mgd.conn_flags);
+ /*
+ * Only set this if we're also going to calculate the AP
+ * settings etc., otherwise this was set before in a
+ * previous call. Note override is set to %true in assoc
+ * if the settings were changed.
+ */
+ link->u.mgd.conn = *conn;
+ err = ieee80211_prep_channel(sdata, link, link->link_id, cbss,
+ mlo, &link->u.mgd.conn);
if (err) {
if (new_sta)
sta_info_free(local, new_sta);
goto out_err;
}
+ /* pass out for use in assoc */
+ *conn = link->u.mgd.conn;
}
if (new_sta) {
@@ -7218,11 +7399,14 @@ int ieee80211_mgd_auth(struct ieee80211_sub_if_data *sdata,
struct ieee80211_local *local = sdata->local;
struct ieee80211_if_managed *ifmgd = &sdata->u.mgd;
struct ieee80211_mgd_auth_data *auth_data;
+ struct ieee80211_conn_settings conn;
struct ieee80211_link_data *link;
const struct element *csa_elem, *ecsa_elem;
+ struct ieee80211_supported_band *sband;
+ struct ieee80211_bss *bss;
u16 auth_alg;
int err;
- bool cont_auth;
+ bool cont_auth, wmm_used;
lockdep_assert_wiphy(sdata->local->hw.wiphy);
@@ -7364,8 +7548,18 @@ int ieee80211_mgd_auth(struct ieee80211_sub_if_data *sdata,
/* needed for transmitting the auth frame(s) properly */
memcpy(sdata->vif.cfg.ap_addr, auth_data->ap_addr, ETH_ALEN);
+ bss = (void *)req->bss->priv;
+ wmm_used = bss->wmm_used && (local->hw.queues >= IEEE80211_NUM_ACS);
+
+ sband = local->hw.wiphy->bands[req->bss->channel->band];
+
+ ieee80211_determine_our_sta_mode(sdata, sband, NULL, wmm_used,
+ req->link_id > 0 ? req->link_id : 0,
+ &conn);
+
err = ieee80211_prep_connection(sdata, req->bss, req->link_id,
- req->ap_mld_addr, cont_auth, false);
+ req->ap_mld_addr, cont_auth,
+ &conn, false);
if (err)
goto err_clear;
@@ -7404,38 +7598,33 @@ int ieee80211_mgd_auth(struct ieee80211_sub_if_data *sdata,
return err;
}
-static ieee80211_conn_flags_t
+static void
ieee80211_setup_assoc_link(struct ieee80211_sub_if_data *sdata,
struct ieee80211_mgd_assoc_data *assoc_data,
struct cfg80211_assoc_request *req,
- ieee80211_conn_flags_t conn_flags,
+ struct ieee80211_conn_settings *conn,
unsigned int link_id)
{
struct ieee80211_local *local = sdata->local;
const struct cfg80211_bss_ies *bss_ies;
struct ieee80211_supported_band *sband;
- const struct element *ht_elem, *vht_elem;
struct ieee80211_link_data *link;
struct cfg80211_bss *cbss;
struct ieee80211_bss *bss;
- bool is_5ghz, is_6ghz;
cbss = assoc_data->link[link_id].bss;
if (WARN_ON(!cbss))
- return 0;
+ return;
bss = (void *)cbss->priv;
sband = local->hw.wiphy->bands[cbss->channel->band];
if (WARN_ON(!sband))
- return 0;
+ return;
link = sdata_dereference(sdata->link[link_id], sdata);
if (WARN_ON(!link))
- return 0;
-
- is_5ghz = cbss->channel->band == NL80211_BAND_5GHZ;
- is_6ghz = cbss->channel->band == NL80211_BAND_6GHZ;
+ return;
/* for MLO connections assume advertising all rates is OK */
if (!req->ap_mld_addr) {
@@ -7452,40 +7641,18 @@ ieee80211_setup_assoc_link(struct ieee80211_sub_if_data *sdata,
assoc_data->ie_pos += req->links[link_id].elems_len;
}
- rcu_read_lock();
- ht_elem = ieee80211_bss_get_elem(cbss, WLAN_EID_HT_OPERATION);
- if (ht_elem && ht_elem->datalen >= sizeof(struct ieee80211_ht_operation))
- assoc_data->link[link_id].ap_ht_param =
- ((struct ieee80211_ht_operation *)(ht_elem->data))->ht_param;
- else if (!is_6ghz)
- conn_flags |= IEEE80211_CONN_DISABLE_HT;
- vht_elem = ieee80211_bss_get_elem(cbss, WLAN_EID_VHT_CAPABILITY);
- if (vht_elem && vht_elem->datalen >= sizeof(struct ieee80211_vht_cap)) {
- memcpy(&assoc_data->link[link_id].ap_vht_cap, vht_elem->data,
- sizeof(struct ieee80211_vht_cap));
- } else if (is_5ghz) {
- link_info(link,
- "VHT capa missing/short, disabling VHT/HE/EHT\n");
- conn_flags |= IEEE80211_CONN_DISABLE_VHT |
- IEEE80211_CONN_DISABLE_HE |
- IEEE80211_CONN_DISABLE_EHT;
- }
- rcu_read_unlock();
-
link->u.mgd.beacon_crc_valid = false;
link->u.mgd.dtim_period = 0;
link->u.mgd.have_beacon = false;
- /* override HT/VHT configuration only if the AP and we support it */
- if (!(conn_flags & IEEE80211_CONN_DISABLE_HT)) {
+ /* override HT configuration only if the AP and we support it */
+ if (conn->mode >= IEEE80211_CONN_MODE_HT) {
struct ieee80211_sta_ht_cap sta_ht_cap;
memcpy(&sta_ht_cap, &sband->ht_cap, sizeof(sta_ht_cap));
ieee80211_apply_htcap_overrides(sdata, &sta_ht_cap);
}
- link->conf->eht_puncturing = 0;
-
rcu_read_lock();
bss_ies = rcu_dereference(cbss->beacon_ies);
if (bss_ies) {
@@ -7506,7 +7673,6 @@ ieee80211_setup_assoc_link(struct ieee80211_sub_if_data *sdata,
}
if (bss_ies) {
- const struct ieee80211_eht_operation *eht_oper;
const struct element *elem;
elem = cfg80211_find_ext_elem(WLAN_EID_EXT_MULTIPLE_BSSID_CONFIGURATION,
@@ -7523,31 +7689,6 @@ ieee80211_setup_assoc_link(struct ieee80211_sub_if_data *sdata,
link->conf->ema_ap = true;
else
link->conf->ema_ap = false;
-
- elem = cfg80211_find_ext_elem(WLAN_EID_EXT_EHT_OPERATION,
- bss_ies->data, bss_ies->len);
- eht_oper = (const void *)(elem->data + 1);
-
- if (elem &&
- ieee80211_eht_oper_size_ok((const void *)(elem->data + 1),
- elem->datalen - 1) &&
- (eht_oper->params & IEEE80211_EHT_OPER_INFO_PRESENT) &&
- (eht_oper->params & IEEE80211_EHT_OPER_DISABLED_SUBCHANNEL_BITMAP_PRESENT)) {
- const struct ieee80211_eht_operation_info *info =
- (void *)eht_oper->optional;
- const u8 *disable_subchannel_bitmap = info->optional;
- u16 bitmap;
-
- bitmap = get_unaligned_le16(disable_subchannel_bitmap);
- if (cfg80211_valid_disable_subchannel_bitmap(&bitmap,
- &link->conf->chandef))
- ieee80211_handle_puncturing_bitmap(link,
- eht_oper,
- bitmap,
- NULL);
- else
- conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- }
}
rcu_read_unlock();
@@ -7574,8 +7715,6 @@ ieee80211_setup_assoc_link(struct ieee80211_sub_if_data *sdata,
} else {
link->smps_mode = link->u.mgd.req_smps;
}
-
- return conn_flags;
}
int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
@@ -7587,11 +7726,9 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
struct ieee80211_mgd_assoc_data *assoc_data;
const struct element *ssid_elem, *csa_elem, *ecsa_elem;
struct ieee80211_vif_cfg *vif_cfg = &sdata->vif.cfg;
- ieee80211_conn_flags_t conn_flags = 0;
struct ieee80211_link_data *link;
struct cfg80211_bss *cbss;
- struct ieee80211_bss *bss;
- bool override;
+ bool override, uapsd_supported;
int i, err;
size_t size = sizeof(*assoc_data) + req->ie_len;
@@ -7612,8 +7749,8 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
ssid_elem = ieee80211_bss_get_elem(cbss, WLAN_EID_SSID);
if (!ssid_elem || ssid_elem->datalen > sizeof(assoc_data->ssid)) {
rcu_read_unlock();
- kfree(assoc_data);
- return -EINVAL;
+ err = -EINVAL;
+ goto err_free;
}
csa_elem = ieee80211_bss_get_elem(cbss, WLAN_EID_CHANNEL_SWITCH);
@@ -7626,51 +7763,122 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
((struct ieee80211_ext_chansw_ie *)ecsa_elem->data)->count != 0)) {
sdata_info(sdata, "AP is in CSA process, reject assoc\n");
rcu_read_unlock();
- kfree(assoc_data);
- return -EINVAL;
+ err = -EINVAL;
+ goto err_free;
}
memcpy(assoc_data->ssid, ssid_elem->data, ssid_elem->datalen);
assoc_data->ssid_len = ssid_elem->datalen;
- memcpy(vif_cfg->ssid, assoc_data->ssid, assoc_data->ssid_len);
- vif_cfg->ssid_len = assoc_data->ssid_len;
rcu_read_unlock();
+ if (ifmgd->associated) {
+ u8 frame_buf[IEEE80211_DEAUTH_FRAME_LEN];
+
+ sdata_info(sdata,
+ "disconnect from AP %pM for new assoc to %pM\n",
+ sdata->vif.cfg.ap_addr, assoc_data->ap_addr);
+ ieee80211_set_disassoc(sdata, IEEE80211_STYPE_DEAUTH,
+ WLAN_REASON_UNSPECIFIED,
+ false, frame_buf);
+
+ ieee80211_report_disconnect(sdata, frame_buf,
+ sizeof(frame_buf), true,
+ WLAN_REASON_UNSPECIFIED,
+ false);
+ }
+
+ memcpy(&ifmgd->ht_capa, &req->ht_capa, sizeof(ifmgd->ht_capa));
+ memcpy(&ifmgd->ht_capa_mask, &req->ht_capa_mask,
+ sizeof(ifmgd->ht_capa_mask));
+
+ memcpy(&ifmgd->vht_capa, &req->vht_capa, sizeof(ifmgd->vht_capa));
+ memcpy(&ifmgd->vht_capa_mask, &req->vht_capa_mask,
+ sizeof(ifmgd->vht_capa_mask));
+
+ memcpy(&ifmgd->s1g_capa, &req->s1g_capa, sizeof(ifmgd->s1g_capa));
+ memcpy(&ifmgd->s1g_capa_mask, &req->s1g_capa_mask,
+ sizeof(ifmgd->s1g_capa_mask));
+
if (req->ap_mld_addr) {
+ uapsd_supported = true;
+
for (i = 0; i < IEEE80211_MLD_MAX_NUM_LINKS; i++) {
- if (!req->links[i].bss)
+ struct ieee80211_supported_band *sband;
+ struct cfg80211_bss *cbss = req->links[i].bss;
+ struct ieee80211_bss *bss;
+
+ if (!cbss)
continue;
+
+ bss = (void *)cbss->priv;
+
+ if (!bss->wmm_used) {
+ err = -EINVAL;
+ goto err_free;
+ }
+
+ if (req->flags & (ASSOC_REQ_DISABLE_HT |
+ ASSOC_REQ_DISABLE_VHT |
+ ASSOC_REQ_DISABLE_HE |
+ ASSOC_REQ_DISABLE_EHT)) {
+ err = -EINVAL;
+ goto err_free;
+ }
+
+ if (cbss->channel->band == NL80211_BAND_S1GHZ) {
+ err = -EINVAL;
+ goto err_free;
+ }
+
link = sdata_dereference(sdata->link[i], sdata);
if (link)
ether_addr_copy(assoc_data->link[i].addr,
link->conf->addr);
else
eth_random_addr(assoc_data->link[i].addr);
+ sband = local->hw.wiphy->bands[cbss->channel->band];
+
+ ieee80211_determine_our_sta_mode(sdata, sband, req, true, i,
+ &assoc_data->link[i].conn);
+ assoc_data->link[i].bss = cbss;
+ assoc_data->link[i].disabled = req->links[i].disabled;
+
+ if (!bss->uapsd_supported)
+ uapsd_supported = false;
}
+
+ memcpy(assoc_data->ap_addr, req->ap_mld_addr, ETH_ALEN);
+ assoc_data->wmm = true;
} else {
+ struct ieee80211_supported_band *sband;
+ struct cfg80211_bss *cbss = req->bss;
+ struct ieee80211_bss *bss = (void *)cbss->priv;
+
memcpy(assoc_data->link[0].addr, sdata->vif.addr, ETH_ALEN);
- }
+ assoc_data->s1g = cbss->channel->band == NL80211_BAND_S1GHZ;
- assoc_data->s1g = cbss->channel->band == NL80211_BAND_S1GHZ;
+ memcpy(assoc_data->ap_addr, cbss->bssid, ETH_ALEN);
- memcpy(assoc_data->ap_addr,
- req->ap_mld_addr ?: req->bss->bssid,
- ETH_ALEN);
+ assoc_data->wmm = bss->wmm_used &&
+ (local->hw.queues >= IEEE80211_NUM_ACS);
- if (ifmgd->associated) {
- u8 frame_buf[IEEE80211_DEAUTH_FRAME_LEN];
+ if (cbss->channel->band == NL80211_BAND_6GHZ &&
+ req->flags & (ASSOC_REQ_DISABLE_HT |
+ ASSOC_REQ_DISABLE_VHT |
+ ASSOC_REQ_DISABLE_HE)) {
+ err = -EINVAL;
+ goto err_free;
+ }
- sdata_info(sdata,
- "disconnect from AP %pM for new assoc to %pM\n",
- sdata->vif.cfg.ap_addr, assoc_data->ap_addr);
- ieee80211_set_disassoc(sdata, IEEE80211_STYPE_DEAUTH,
- WLAN_REASON_UNSPECIFIED,
- false, frame_buf);
+ sband = local->hw.wiphy->bands[cbss->channel->band];
- ieee80211_report_disconnect(sdata, frame_buf,
- sizeof(frame_buf), true,
- WLAN_REASON_UNSPECIFIED,
- false);
+ assoc_data->link[0].bss = cbss;
+
+ ieee80211_determine_our_sta_mode(sdata, sband, req,
+ assoc_data->wmm, 0,
+ &assoc_data->link[0].conn);
+
+ uapsd_supported = bss->uapsd_supported;
}
if (ifmgd->auth_data && !ifmgd->auth_data->done) {
@@ -7696,76 +7904,6 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
ieee80211_destroy_auth_data(sdata, false);
}
- /* prepare assoc data */
-
- bss = (void *)cbss->priv;
- assoc_data->wmm = bss->wmm_used &&
- (local->hw.queues >= IEEE80211_NUM_ACS);
-
- /*
- * IEEE802.11n does not allow TKIP/WEP as pairwise ciphers in HT mode.
- * We still associate in non-HT mode (11a/b/g) if any one of these
- * ciphers is configured as pairwise.
- * We can set this to true for non-11n hardware, that'll be checked
- * separately along with the peer capabilities.
- */
- for (i = 0; i < req->crypto.n_ciphers_pairwise; i++) {
- if (req->crypto.ciphers_pairwise[i] == WLAN_CIPHER_SUITE_WEP40 ||
- req->crypto.ciphers_pairwise[i] == WLAN_CIPHER_SUITE_TKIP ||
- req->crypto.ciphers_pairwise[i] == WLAN_CIPHER_SUITE_WEP104) {
- conn_flags |= IEEE80211_CONN_DISABLE_HT;
- conn_flags |= IEEE80211_CONN_DISABLE_VHT;
- conn_flags |= IEEE80211_CONN_DISABLE_HE;
- conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- netdev_info(sdata->dev,
- "disabling HT/VHT/HE due to WEP/TKIP use\n");
- }
- }
-
- /* also disable HT/VHT/HE/EHT if the AP doesn't use WMM */
- if (!bss->wmm_used) {
- conn_flags |= IEEE80211_CONN_DISABLE_HT;
- conn_flags |= IEEE80211_CONN_DISABLE_VHT;
- conn_flags |= IEEE80211_CONN_DISABLE_HE;
- conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- netdev_info(sdata->dev,
- "disabling HT/VHT/HE as WMM/QoS is not supported by the AP\n");
- }
-
- if (req->flags & ASSOC_REQ_DISABLE_HT) {
- mlme_dbg(sdata, "HT disabled by flag, disabling HT/VHT/HE\n");
- conn_flags |= IEEE80211_CONN_DISABLE_HT;
- conn_flags |= IEEE80211_CONN_DISABLE_VHT;
- conn_flags |= IEEE80211_CONN_DISABLE_HE;
- conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- }
-
- if (req->flags & ASSOC_REQ_DISABLE_VHT) {
- mlme_dbg(sdata, "VHT disabled by flag, disabling VHT\n");
- conn_flags |= IEEE80211_CONN_DISABLE_VHT;
- }
-
- if (req->flags & ASSOC_REQ_DISABLE_HE) {
- mlme_dbg(sdata, "HE disabled by flag, disabling HE/EHT\n");
- conn_flags |= IEEE80211_CONN_DISABLE_HE;
- conn_flags |= IEEE80211_CONN_DISABLE_EHT;
- }
-
- if (req->flags & ASSOC_REQ_DISABLE_EHT)
- conn_flags |= IEEE80211_CONN_DISABLE_EHT;
-
- memcpy(&ifmgd->ht_capa, &req->ht_capa, sizeof(ifmgd->ht_capa));
- memcpy(&ifmgd->ht_capa_mask, &req->ht_capa_mask,
- sizeof(ifmgd->ht_capa_mask));
-
- memcpy(&ifmgd->vht_capa, &req->vht_capa, sizeof(ifmgd->vht_capa));
- memcpy(&ifmgd->vht_capa_mask, &req->vht_capa_mask,
- sizeof(ifmgd->vht_capa_mask));
-
- memcpy(&ifmgd->s1g_capa, &req->s1g_capa, sizeof(ifmgd->s1g_capa));
- memcpy(&ifmgd->s1g_capa_mask, &req->s1g_capa_mask,
- sizeof(ifmgd->s1g_capa_mask));
-
if (req->ie && req->ie_len) {
memcpy(assoc_data->ie, req->ie, req->ie_len);
assoc_data->ie_len = req->ie_len;
@@ -7796,19 +7934,10 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
assoc_data->assoc_link_id = assoc_link_id;
if (req->ap_mld_addr) {
- for (i = 0; i < ARRAY_SIZE(assoc_data->link); i++) {
- assoc_data->link[i].conn_flags = conn_flags;
- assoc_data->link[i].bss = req->links[i].bss;
- assoc_data->link[i].disabled = req->links[i].disabled;
- }
-
/* if there was no authentication, set up the link */
err = ieee80211_vif_set_links(sdata, BIT(assoc_link_id), 0);
if (err)
goto err_clear;
- } else {
- assoc_data->link[0].conn_flags = conn_flags;
- assoc_data->link[0].bss = cbss;
}
link = sdata_dereference(sdata->link[assoc_link_id], sdata);
@@ -7817,19 +7946,21 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
goto err_clear;
}
- /* keep old conn_flags from ieee80211_prep_channel() from auth */
- conn_flags |= link->u.mgd.conn_flags;
- conn_flags |= ieee80211_setup_assoc_link(sdata, assoc_data, req,
- conn_flags, assoc_link_id);
- override = link->u.mgd.conn_flags != conn_flags;
- link->u.mgd.conn_flags |= conn_flags;
+ override = link->u.mgd.conn.mode !=
+ assoc_data->link[assoc_link_id].conn.mode ||
+ link->u.mgd.conn.bw_limit !=
+ assoc_data->link[assoc_link_id].conn.bw_limit;
+ link->u.mgd.conn = assoc_data->link[assoc_link_id].conn;
+
+ ieee80211_setup_assoc_link(sdata, assoc_data, req, &link->u.mgd.conn,
+ assoc_link_id);
if (WARN((sdata->vif.driver_flags & IEEE80211_VIF_SUPPORTS_UAPSD) &&
ieee80211_hw_check(&local->hw, PS_NULLFUNC_STACK),
"U-APSD not supported with HW_PS_NULLFUNC_STACK\n"))
sdata->vif.driver_flags &= ~IEEE80211_VIF_SUPPORTS_UAPSD;
- if (bss->wmm_used && bss->uapsd_supported &&
+ if (assoc_data->wmm && uapsd_supported &&
(sdata->vif.driver_flags & IEEE80211_VIF_SUPPORTS_UAPSD)) {
assoc_data->uapsd = true;
ifmgd->flags |= IEEE80211_STA_UAPSD_ENABLED;
@@ -7873,27 +8004,29 @@ int ieee80211_mgd_assoc(struct ieee80211_sub_if_data *sdata,
continue;
if (i == assoc_data->assoc_link_id)
continue;
- /* only calculate the flags, hence link == NULL */
- err = ieee80211_prep_channel(sdata, NULL,
+ /* only calculate the mode, hence link == NULL */
+ err = ieee80211_prep_channel(sdata, NULL, i,
assoc_data->link[i].bss, true,
- &assoc_data->link[i].conn_flags);
+ &assoc_data->link[i].conn);
if (err) {
req->links[i].error = err;
goto err_clear;
}
}
+ memcpy(vif_cfg->ssid, assoc_data->ssid, assoc_data->ssid_len);
+ vif_cfg->ssid_len = assoc_data->ssid_len;
+
/* needed for transmitting the assoc frames properly */
memcpy(sdata->vif.cfg.ap_addr, assoc_data->ap_addr, ETH_ALEN);
err = ieee80211_prep_connection(sdata, cbss, req->link_id,
- req->ap_mld_addr, true, override);
+ req->ap_mld_addr, true,
+ &assoc_data->link[assoc_link_id].conn,
+ override);
if (err)
goto err_clear;
- assoc_data->link[assoc_data->assoc_link_id].conn_flags =
- link->u.mgd.conn_flags;
-
if (ieee80211_hw_check(&sdata->local->hw, NEED_DTIM_BEFORE_ASSOC)) {
const struct cfg80211_bss_ies *beacon_ies;
@@ -23,7 +23,8 @@ int ieee80211_parse_ch_switch_ie(struct ieee80211_sub_if_data *sdata,
struct ieee802_11_elems *elems,
enum nl80211_band current_band,
u32 vht_cap_info,
- ieee80211_conn_flags_t conn_flags, u8 *bssid,
+ struct ieee80211_conn_settings *conn,
+ u8 *bssid,
struct ieee80211_csa_ie *csa_ie)
{
enum nl80211_band new_band = current_band;
@@ -42,13 +43,13 @@ int ieee80211_parse_ch_switch_ie(struct ieee80211_sub_if_data *sdata,
wide_bw_chansw_ie = elems->wide_bw_chansw_ie;
bwi = elems->bandwidth_indication;
- if (conn_flags & (IEEE80211_CONN_DISABLE_HT |
- IEEE80211_CONN_DISABLE_40MHZ)) {
+ if (conn->mode < IEEE80211_CONN_MODE_HT ||
+ conn->bw_limit < IEEE80211_CONN_BW_LIMIT_40) {
sec_chan_offs = NULL;
wide_bw_chansw_ie = NULL;
}
- if (conn_flags & IEEE80211_CONN_DISABLE_VHT)
+ if (conn->mode < IEEE80211_CONN_MODE_VHT)
wide_bw_chansw_ie = NULL;
if (elems->ext_chansw_ie) {
@@ -95,7 +96,7 @@ int ieee80211_parse_ch_switch_ie(struct ieee80211_sub_if_data *sdata,
if (sec_chan_offs) {
secondary_channel_offset = sec_chan_offs->sec_chan_offs;
- } else if (!(conn_flags & IEEE80211_CONN_DISABLE_HT)) {
+ } else if (conn->mode >= IEEE80211_CONN_MODE_HT) {
/* If the secondary channel offset IE is not present,
* we can't know what's the post-CSA offset, so the
* best we can do is use 20MHz.
@@ -169,12 +170,10 @@ int ieee80211_parse_ch_switch_ie(struct ieee80211_sub_if_data *sdata,
&new_vht_chandef))
new_vht_chandef.chan = NULL;
- if (conn_flags & IEEE80211_CONN_DISABLE_80P80MHZ &&
- new_vht_chandef.width == NL80211_CHAN_WIDTH_80P80)
- ieee80211_chandef_downgrade(&new_vht_chandef);
- if (conn_flags & IEEE80211_CONN_DISABLE_160MHZ &&
- new_vht_chandef.width == NL80211_CHAN_WIDTH_160)
- ieee80211_chandef_downgrade(&new_vht_chandef);
+ if (conn->bw_limit < IEEE80211_CONN_BW_LIMIT_160 &&
+ (new_vht_chandef.width == NL80211_CHAN_WIDTH_80P80 ||
+ new_vht_chandef.width == NL80211_CHAN_WIDTH_160))
+ ieee80211_chandef_downgrade(&new_vht_chandef, NULL);
}
/* if VHT data is there validate & use it */
@@ -347,7 +347,7 @@ ieee80211_tdls_chandef_vht_upgrade(struct ieee80211_sub_if_data *sdata,
(uc.width > sta->tdls_chandef.width &&
!cfg80211_reg_can_beacon_relax(sdata->local->hw.wiphy, &uc,
sdata->wdev.iftype)))
- ieee80211_chandef_downgrade(&uc);
+ ieee80211_chandef_downgrade(&uc, NULL);
if (!cfg80211_chandef_identical(&uc, &sta->tdls_chandef)) {
tdls_dbg(sdata, "TDLS ch width upgraded %d -> %d\n",
@@ -561,7 +561,7 @@ ieee80211_tdls_add_setup_start_ies(struct ieee80211_link_data *link,
ieee80211_he_ppe_size(he_cap->ppe_thres[0],
he_cap->he_cap_elem.phy_cap_info);
pos = skb_put(skb, cap_size);
- pos = ieee80211_ie_build_he_cap(0, pos, he_cap, pos + cap_size);
+ pos = ieee80211_ie_build_he_cap(NULL, he_cap, pos, pos + cap_size);
/* Build HE 6Ghz capa IE from sband */
if (sband->band == NL80211_BAND_6GHZ) {
@@ -1413,8 +1413,8 @@ iee80211_tdls_recalc_ht_protection(struct ieee80211_sub_if_data *sdata,
IEEE80211_HT_OP_MODE_NON_HT_STA_PRSNT;
u16 opmode;
- /* Nothing to do if the BSS connection uses HT */
- if (!(sdata->deflink.u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HT))
+ /* Nothing to do if the BSS connection uses (at least) HT */
+ if (sdata->deflink.u.mgd.conn.mode >= IEEE80211_CONN_MODE_HT)
return;
tdls_ht = (sta && sta->sta.deflink.ht_cap.ht_supported) ||
@@ -46,6 +46,11 @@ struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy)
}
EXPORT_SYMBOL(wiphy_to_ieee80211_hw);
+const struct ieee80211_conn_settings ieee80211_conn_settings_unlimited = {
+ .mode = IEEE80211_CONN_MODE_EHT,
+ .bw_limit = IEEE80211_CONN_BW_LIMIT_320,
+};
+
u8 *ieee80211_get_bssid(struct ieee80211_hdr *hdr, size_t len,
enum nl80211_iftype type)
{
@@ -929,23 +934,31 @@ ieee80211_parse_extension_element(u32 *crc,
switch (elem->data[0]) {
case WLAN_EID_EXT_HE_MU_EDCA:
+ if (params->mode < IEEE80211_CONN_MODE_HE)
+ break;
calc_crc = true;
if (len >= sizeof(*elems->mu_edca_param_set))
elems->mu_edca_param_set = data;
break;
case WLAN_EID_EXT_HE_CAPABILITY:
+ if (params->mode < IEEE80211_CONN_MODE_HE)
+ break;
if (ieee80211_he_capa_size_ok(data, len)) {
elems->he_cap = data;
elems->he_cap_len = len;
}
break;
case WLAN_EID_EXT_HE_OPERATION:
+ if (params->mode < IEEE80211_CONN_MODE_HE)
+ break;
calc_crc = true;
if (len >= sizeof(*elems->he_operation) &&
len >= ieee80211_he_oper_size(data) - 1)
elems->he_operation = data;
break;
case WLAN_EID_EXT_UORA:
+ if (params->mode < IEEE80211_CONN_MODE_HE)
+ break;
if (len >= 1)
elems->uora_element = data;
break;
@@ -958,15 +971,21 @@ ieee80211_parse_extension_element(u32 *crc,
elems->mbssid_config_ie = data;
break;
case WLAN_EID_EXT_HE_SPR:
+ if (params->mode < IEEE80211_CONN_MODE_HE)
+ break;
if (len >= sizeof(*elems->he_spr) &&
len >= ieee80211_he_spr_size(data))
elems->he_spr = data;
break;
case WLAN_EID_EXT_HE_6GHZ_CAPA:
+ if (params->mode < IEEE80211_CONN_MODE_HE)
+ break;
if (len >= sizeof(*elems->he_6ghz_capa))
elems->he_6ghz_capa = data;
break;
case WLAN_EID_EXT_EHT_CAPABILITY:
+ if (params->mode < IEEE80211_CONN_MODE_EHT)
+ break;
if (ieee80211_eht_capa_size_ok(elems->he_cap,
data, len,
params->from_ap)) {
@@ -975,11 +994,15 @@ ieee80211_parse_extension_element(u32 *crc,
}
break;
case WLAN_EID_EXT_EHT_OPERATION:
+ if (params->mode < IEEE80211_CONN_MODE_EHT)
+ break;
if (ieee80211_eht_oper_size_ok(data, len))
elems->eht_operation = data;
calc_crc = true;
break;
case WLAN_EID_EXT_EHT_MULTI_LINK:
+ if (params->mode < IEEE80211_CONN_MODE_EHT)
+ break;
calc_crc = true;
if (ieee80211_mle_size_ok(data, len)) {
@@ -1004,11 +1027,15 @@ ieee80211_parse_extension_element(u32 *crc,
}
break;
case WLAN_EID_EXT_BANDWIDTH_INDICATION:
+ if (params->mode < IEEE80211_CONN_MODE_EHT)
+ break;
if (ieee80211_bandwidth_indication_size_ok(data, len))
elems->bandwidth_indication = data;
calc_crc = true;
break;
case WLAN_EID_EXT_TID_TO_LINK_MAPPING:
+ if (params->mode < IEEE80211_CONN_MODE_EHT)
+ break;
calc_crc = true;
if (ieee80211_tid_to_link_map_size_ok(data, len) &&
elems->ttlm_num < ARRAY_SIZE(elems->ttlm)) {
@@ -1178,24 +1205,32 @@ _ieee802_11_parse_elems_full(struct ieee80211_elems_parse_params *params,
elems->ext_supp_rates_len = elen;
break;
case WLAN_EID_HT_CAPABILITY:
+ if (params->mode < IEEE80211_CONN_MODE_HT)
+ break;
if (elen >= sizeof(struct ieee80211_ht_cap))
elems->ht_cap_elem = (void *)pos;
else
elem_parse_failed = true;
break;
case WLAN_EID_HT_OPERATION:
+ if (params->mode < IEEE80211_CONN_MODE_HT)
+ break;
if (elen >= sizeof(struct ieee80211_ht_operation))
elems->ht_operation = (void *)pos;
else
elem_parse_failed = true;
break;
case WLAN_EID_VHT_CAPABILITY:
+ if (params->mode < IEEE80211_CONN_MODE_VHT)
+ break;
if (elen >= sizeof(struct ieee80211_vht_cap))
elems->vht_cap_elem = (void *)pos;
else
elem_parse_failed = true;
break;
case WLAN_EID_VHT_OPERATION:
+ if (params->mode < IEEE80211_CONN_MODE_VHT)
+ break;
if (elen >= sizeof(struct ieee80211_vht_operation)) {
elems->vht_operation = (void *)pos;
if (calc_crc)
@@ -1205,6 +1240,8 @@ _ieee802_11_parse_elems_full(struct ieee80211_elems_parse_params *params,
elem_parse_failed = true;
break;
case WLAN_EID_OPMODE_NOTIF:
+ if (params->mode < IEEE80211_CONN_MODE_VHT)
+ break;
if (elen > 0) {
elems->opmode_notif = pos;
if (calc_crc)
@@ -1264,6 +1301,8 @@ _ieee802_11_parse_elems_full(struct ieee80211_elems_parse_params *params,
elems->ext_chansw_ie = (void *)pos;
break;
case WLAN_EID_SECONDARY_CHANNEL_OFFSET:
+ if (params->mode < IEEE80211_CONN_MODE_HT)
+ break;
if (elen != sizeof(struct ieee80211_sec_chan_offs_ie)) {
elem_parse_failed = true;
break;
@@ -1279,6 +1318,8 @@ _ieee802_11_parse_elems_full(struct ieee80211_elems_parse_params *params,
elems->mesh_chansw_params_ie = (void *)pos;
break;
case WLAN_EID_WIDE_BW_CHANNEL_SWITCH:
+ if (params->mode < IEEE80211_CONN_MODE_VHT) // ??
+ break;
if (!params->action ||
elen < sizeof(*elems->wide_bw_chansw_ie)) {
elem_parse_failed = true;
@@ -1287,6 +1328,8 @@ _ieee802_11_parse_elems_full(struct ieee80211_elems_parse_params *params,
elems->wide_bw_chansw_ie = (void *)pos;
break;
case WLAN_EID_CHANNEL_SWITCH_WRAPPER:
+ if (params->mode < IEEE80211_CONN_MODE_VHT) // ??
+ break;
if (params->action) {
elem_parse_failed = true;
break;
@@ -1305,6 +1348,9 @@ _ieee802_11_parse_elems_full(struct ieee80211_elems_parse_params *params,
elem_parse_failed = true;
}
+ if (params->mode < IEEE80211_CONN_MODE_EHT)
+ break;
+
subelem = cfg80211_find_ext_elem(WLAN_EID_EXT_BANDWIDTH_INDICATION,
pos, elen);
if (subelem) {
@@ -1376,6 +1422,8 @@ _ieee802_11_parse_elems_full(struct ieee80211_elems_parse_params *params,
elems->rsnx_len = elen;
break;
case WLAN_EID_TX_POWER_ENVELOPE:
+ if (params->mode < IEEE80211_CONN_MODE_VHT) // ??
+ break;
if (elen < 1 ||
elen > sizeof(struct ieee80211_tx_pwr_env))
break;
@@ -1393,24 +1441,32 @@ _ieee802_11_parse_elems_full(struct ieee80211_elems_parse_params *params,
elem, elems, params);
break;
case WLAN_EID_S1G_CAPABILITIES:
+ if (params->mode != IEEE80211_CONN_MODE_S1G)
+ break;
if (elen >= sizeof(*elems->s1g_capab))
elems->s1g_capab = (void *)pos;
else
elem_parse_failed = true;
break;
case WLAN_EID_S1G_OPERATION:
+ if (params->mode != IEEE80211_CONN_MODE_S1G)
+ break;
if (elen == sizeof(*elems->s1g_oper))
elems->s1g_oper = (void *)pos;
else
elem_parse_failed = true;
break;
case WLAN_EID_S1G_BCN_COMPAT:
+ if (params->mode != IEEE80211_CONN_MODE_S1G)
+ break;
if (elen == sizeof(*elems->s1g_bcn_compat))
elems->s1g_bcn_compat = (void *)pos;
else
elem_parse_failed = true;
break;
case WLAN_EID_AID_RESPONSE:
+ if (params->mode != IEEE80211_CONN_MODE_S1G)
+ break;
if (elen == sizeof(struct ieee80211_aid_response_ie))
elems->aid_resp = (void *)pos;
else
@@ -1562,6 +1618,7 @@ static void ieee80211_mle_parse_link(struct ieee802_11_elems *elems,
{
struct ieee80211_mle_per_sta_profile *prof;
struct ieee80211_elems_parse_params sub = {
+ .mode = params->mode,
.action = params->action,
.from_ap = params->from_ap,
.link_id = -1,
@@ -1649,6 +1706,7 @@ ieee802_11_parse_elems_full(struct ieee80211_elems_parse_params *params)
/* Override with nontransmitted profile, if found */
if (nontransmitted_profile_len) {
struct ieee80211_elems_parse_params sub = {
+ .mode = params->mode,
.start = nontransmitted_profile,
.len = nontransmitted_profile_len,
.action = params->action,
@@ -2142,7 +2200,7 @@ static int ieee80211_build_preq_ies_band(struct ieee80211_sub_if_data *sdata,
if (he_cap &&
cfg80211_any_usable_channels(local->hw.wiphy, BIT(sband->band),
IEEE80211_CHAN_NO_HE)) {
- pos = ieee80211_ie_build_he_cap(0, pos, he_cap, end);
+ pos = ieee80211_ie_build_he_cap(NULL, he_cap, pos, end);
if (!pos)
goto out_err;
}
@@ -3201,15 +3259,18 @@ u8 ieee80211_ie_len_he_cap(struct ieee80211_sub_if_data *sdata, u8 iftype)
he_cap->he_cap_elem.phy_cap_info);
}
-u8 *ieee80211_ie_build_he_cap(ieee80211_conn_flags_t disable_flags, u8 *pos,
+u8 *ieee80211_ie_build_he_cap(const struct ieee80211_conn_settings *conn,
const struct ieee80211_sta_he_cap *he_cap,
- u8 *end)
+ u8 *pos, u8 *end)
{
struct ieee80211_he_cap_elem elem;
u8 n;
u8 ie_len;
u8 *orig_pos = pos;
+ if (!conn)
+ conn = &ieee80211_conn_settings_unlimited;
+
/* Make sure we have place for the IE */
/*
* TODO: the 1 added is because this temporarily is under the EXTENSION
@@ -3221,18 +3282,15 @@ u8 *ieee80211_ie_build_he_cap(ieee80211_conn_flags_t disable_flags, u8 *pos,
/* modify on stack first to calculate 'n' and 'ie_len' correctly */
elem = he_cap->he_cap_elem;
- if (disable_flags & IEEE80211_CONN_DISABLE_40MHZ)
+ if (conn->bw_limit < IEEE80211_CONN_BW_LIMIT_40)
elem.phy_cap_info[0] &=
~(IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_80MHZ_IN_5G |
IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_40MHZ_IN_2G);
- if (disable_flags & IEEE80211_CONN_DISABLE_160MHZ)
+ if (conn->bw_limit < IEEE80211_CONN_BW_LIMIT_160)
elem.phy_cap_info[0] &=
- ~IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G;
-
- if (disable_flags & IEEE80211_CONN_DISABLE_80P80MHZ)
- elem.phy_cap_info[0] &=
- ~IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G;
+ ~(IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_160MHZ_IN_5G |
+ IEEE80211_HE_PHY_CAP0_CHANNEL_WIDTH_SET_80PLUS80_MHZ_IN_5G);
n = ieee80211_he_mcs_nss_size(&elem);
ie_len = 2 + 1 +
@@ -4382,21 +4440,32 @@ void ieee80211_radar_detected(struct ieee80211_hw *hw)
}
EXPORT_SYMBOL(ieee80211_radar_detected);
-ieee80211_conn_flags_t ieee80211_chandef_downgrade(struct cfg80211_chan_def *c)
+void ieee80211_chandef_downgrade(struct cfg80211_chan_def *c,
+ struct ieee80211_conn_settings *conn)
{
- ieee80211_conn_flags_t ret;
+ struct ieee80211_conn_settings _ignored = {};
int tmp;
+ /* allow passing NULL if caller doesn't care */
+ if (!conn)
+ conn = &_ignored;
+
switch (c->width) {
+ default:
+ case NL80211_CHAN_WIDTH_20_NOHT:
+ WARN_ON_ONCE(1);
+ fallthrough;
case NL80211_CHAN_WIDTH_20:
c->width = NL80211_CHAN_WIDTH_20_NOHT;
- ret = IEEE80211_CONN_DISABLE_HT | IEEE80211_CONN_DISABLE_VHT;
+ conn->mode = IEEE80211_CONN_MODE_LEGACY;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_20;
break;
case NL80211_CHAN_WIDTH_40:
c->width = NL80211_CHAN_WIDTH_20;
c->center_freq1 = c->chan->center_freq;
- ret = IEEE80211_CONN_DISABLE_40MHZ |
- IEEE80211_CONN_DISABLE_VHT;
+ if (conn->mode == IEEE80211_CONN_MODE_VHT)
+ conn->mode = IEEE80211_CONN_MODE_HT;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_20;
break;
case NL80211_CHAN_WIDTH_80:
tmp = (30 + c->chan->center_freq - c->center_freq1)/20;
@@ -4405,13 +4474,14 @@ ieee80211_conn_flags_t ieee80211_chandef_downgrade(struct cfg80211_chan_def *c)
/* freq_P40 */
c->center_freq1 = c->center_freq1 - 20 + 40 * tmp;
c->width = NL80211_CHAN_WIDTH_40;
- ret = IEEE80211_CONN_DISABLE_VHT;
+ if (conn->mode == IEEE80211_CONN_MODE_VHT)
+ conn->mode = IEEE80211_CONN_MODE_HT;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_80;
break;
case NL80211_CHAN_WIDTH_80P80:
c->center_freq2 = 0;
c->width = NL80211_CHAN_WIDTH_80;
- ret = IEEE80211_CONN_DISABLE_80P80MHZ |
- IEEE80211_CONN_DISABLE_160MHZ;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_80;
break;
case NL80211_CHAN_WIDTH_160:
/* n_P20 */
@@ -4420,8 +4490,7 @@ ieee80211_conn_flags_t ieee80211_chandef_downgrade(struct cfg80211_chan_def *c)
tmp /= 4;
c->center_freq1 = c->center_freq1 - 40 + 80 * tmp;
c->width = NL80211_CHAN_WIDTH_80;
- ret = IEEE80211_CONN_DISABLE_80P80MHZ |
- IEEE80211_CONN_DISABLE_160MHZ;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_80;
break;
case NL80211_CHAN_WIDTH_320:
/* n_P20 */
@@ -4430,13 +4499,7 @@ ieee80211_conn_flags_t ieee80211_chandef_downgrade(struct cfg80211_chan_def *c)
tmp /= 8;
c->center_freq1 = c->center_freq1 - 80 + 160 * tmp;
c->width = NL80211_CHAN_WIDTH_160;
- ret = IEEE80211_CONN_DISABLE_320MHZ;
- break;
- default:
- case NL80211_CHAN_WIDTH_20_NOHT:
- WARN_ON_ONCE(1);
- c->width = NL80211_CHAN_WIDTH_20_NOHT;
- ret = IEEE80211_CONN_DISABLE_HT | IEEE80211_CONN_DISABLE_VHT;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_160;
break;
case NL80211_CHAN_WIDTH_1:
case NL80211_CHAN_WIDTH_2:
@@ -4447,13 +4510,12 @@ ieee80211_conn_flags_t ieee80211_chandef_downgrade(struct cfg80211_chan_def *c)
case NL80211_CHAN_WIDTH_10:
WARN_ON_ONCE(1);
/* keep c->width */
- ret = IEEE80211_CONN_DISABLE_HT | IEEE80211_CONN_DISABLE_VHT;
+ conn->mode = IEEE80211_CONN_MODE_LEGACY;
+ conn->bw_limit = IEEE80211_CONN_BW_LIMIT_20;
break;
}
WARN_ON_ONCE(!cfg80211_chandef_valid(c));
-
- return ret;
}
/*