| Message ID | 20240227063613.4478-2-quic_bqiang@quicinc.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Delegated to: | Kalle Valo |
| Headers | show |
| Series | wifi: ath11k: hibernation support | expand |
On Tue, Feb 27, 2024 at 02:36:11PM +0800, Baochen Qiang wrote: > ath11k fails to resume: > > ath11k_pci 0000:06:00.0: timeout while waiting for restart complete > > This happens because when calling mhi_sync_power_up() the MHI subsystem > eventually calls device_add() from mhi_create_devices() but the device > creation is deferred: > > mhi mhi0_IPCR: Driver qcom_mhi_qrtr force probe deferral > > The reason for deferring device creation is explained in dpm_prepare(): > > /* > * It is unsafe if probing of devices will happen during suspend or > * hibernation and system behavior will be unpredictable in this case. > * So, let's prohibit device's probing here and defer their probes > * instead. The normal behavior will be restored in dpm_complete(). > */ > > Because the device probe is deferred, the qcom_mhi_qrtr_probe() is not > called and thus MHI channels are not prepared: > > So what this means that QRTR is not delivering messages and the QMI connection > is not working between ath11k and the firmware, resulting a failure in firmware > initialization. > > To fix this add new function mhi_power_down_keep_dev() which doesn't destroy > the devices for channels during power down. This way we avoid probe defer issue > and finally can get ath11k hibernation working with the following patches. > > Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 > > Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> > Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Small nitpicks below. With that fixed, Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Unfortunately, I just sent the PR for 6.9. If possible, I'll try to send v2. Otherwise, I can only apply it for 6.10. > --- > drivers/bus/mhi/host/internal.h | 4 +++- > drivers/bus/mhi/host/pm.c | 41 ++++++++++++++++++++++++++++----- > include/linux/mhi.h | 18 ++++++++++++++- > 3 files changed, 55 insertions(+), 8 deletions(-) > > diff --git a/drivers/bus/mhi/host/internal.h b/drivers/bus/mhi/host/internal.h > index 5fe49311b8eb..aaad40a07f69 100644 > --- a/drivers/bus/mhi/host/internal.h > +++ b/drivers/bus/mhi/host/internal.h > @@ -80,6 +80,7 @@ enum dev_st_transition { > DEV_ST_TRANSITION_FP, > DEV_ST_TRANSITION_SYS_ERR, > DEV_ST_TRANSITION_DISABLE, > + DEV_ST_TRANSITION_DISABLE_DESTROY_DEVICE, > DEV_ST_TRANSITION_MAX, > }; > > @@ -90,7 +91,8 @@ enum dev_st_transition { > dev_st_trans(MISSION_MODE, "MISSION MODE") \ > dev_st_trans(FP, "FLASH PROGRAMMER") \ > dev_st_trans(SYS_ERR, "SYS ERROR") \ > - dev_st_trans_end(DISABLE, "DISABLE") > + dev_st_trans(DISABLE, "DISABLE") \ > + dev_st_trans_end(DISABLE_DESTROY_DEVICE, "DISABLE (DESTROY DEVICE)") > > extern const char * const dev_state_tran_str[DEV_ST_TRANSITION_MAX]; > #define TO_DEV_STATE_TRANS_STR(state) (((state) >= DEV_ST_TRANSITION_MAX) ? \ > diff --git a/drivers/bus/mhi/host/pm.c b/drivers/bus/mhi/host/pm.c > index 8b40d3f01acc..4b817b259a3e 100644 > --- a/drivers/bus/mhi/host/pm.c > +++ b/drivers/bus/mhi/host/pm.c > @@ -468,7 +468,8 @@ static int mhi_pm_mission_mode_transition(struct mhi_controller *mhi_cntrl) > } > > /* Handle shutdown transitions */ > -static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl) > +static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl, > + bool destroy_device) > { > enum mhi_pm_state cur_state; > struct mhi_event *mhi_event; > @@ -530,8 +531,15 @@ static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl) > dev_dbg(dev, "Waiting for all pending threads to complete\n"); > wake_up_all(&mhi_cntrl->state_event); > > - dev_dbg(dev, "Reset all active channels and remove MHI devices\n"); > - device_for_each_child(&mhi_cntrl->mhi_dev->dev, NULL, mhi_destroy_device); > + /** Use the preferred style for multi line comments: /* *... */ > + * Some MHI controller drivers, ath11k as an example, would like to keep > + * MHI deivces for channels during suspend/hibernation to avoid the > + * probe defer issue. Add a check here to make it possible. How about: Only destroy the 'struct device' for channels if indicated by the 'destroy_device' flag. Because, during system suspend or hibernation state, there is no need to destroy the 'struct device' as the endpoint device would still be physically attached to the machine. - Mani > + */ > + if (destroy_device) { > + dev_dbg(dev, "Reset all active channels and remove MHI devices\n"); > + device_for_each_child(&mhi_cntrl->mhi_dev->dev, NULL, mhi_destroy_device); > + } > > mutex_lock(&mhi_cntrl->pm_mutex); > > @@ -821,7 +829,10 @@ void mhi_pm_st_worker(struct work_struct *work) > mhi_pm_sys_error_transition(mhi_cntrl); > break; > case DEV_ST_TRANSITION_DISABLE: > - mhi_pm_disable_transition(mhi_cntrl); > + mhi_pm_disable_transition(mhi_cntrl, false); > + break; > + case DEV_ST_TRANSITION_DISABLE_DESTROY_DEVICE: > + mhi_pm_disable_transition(mhi_cntrl, true); > break; > default: > break; > @@ -1175,7 +1186,8 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl) > } > EXPORT_SYMBOL_GPL(mhi_async_power_up); > > -void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful) > +static void __mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful, > + bool destroy_device) > { > enum mhi_pm_state cur_state, transition_state; > struct device *dev = &mhi_cntrl->mhi_dev->dev; > @@ -1211,15 +1223,32 @@ void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful) > write_unlock_irq(&mhi_cntrl->pm_lock); > mutex_unlock(&mhi_cntrl->pm_mutex); > > - mhi_queue_state_transition(mhi_cntrl, DEV_ST_TRANSITION_DISABLE); > + if (destroy_device) > + mhi_queue_state_transition(mhi_cntrl, > + DEV_ST_TRANSITION_DISABLE_DESTROY_DEVICE); > + else > + mhi_queue_state_transition(mhi_cntrl, > + DEV_ST_TRANSITION_DISABLE); > > /* Wait for shutdown to complete */ > flush_work(&mhi_cntrl->st_worker); > > disable_irq(mhi_cntrl->irq[0]); > } > + > +void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful) > +{ > + __mhi_power_down(mhi_cntrl, graceful, true); > +} > EXPORT_SYMBOL_GPL(mhi_power_down); > > +void mhi_power_down_keep_dev(struct mhi_controller *mhi_cntrl, > + bool graceful) > +{ > + __mhi_power_down(mhi_cntrl, graceful, false); > +} > +EXPORT_SYMBOL_GPL(mhi_power_down_keep_dev); > + > int mhi_sync_power_up(struct mhi_controller *mhi_cntrl) > { > int ret = mhi_async_power_up(mhi_cntrl); > diff --git a/include/linux/mhi.h b/include/linux/mhi.h > index 77b8c0a26674..5ce1fc1167d0 100644 > --- a/include/linux/mhi.h > +++ b/include/linux/mhi.h > @@ -630,12 +630,28 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl); > int mhi_sync_power_up(struct mhi_controller *mhi_cntrl); > > /** > - * mhi_power_down - Start MHI power down sequence > + * mhi_power_down - Power down the MHI device and also destroy the > + * 'struct device' for the channels associated with it. > + * See also mhi_power_down_keep_dev() which is a variant > + * of this API that keeps the 'struct device' for channels > + * (useful during suspend/hibernation). > * @mhi_cntrl: MHI controller > * @graceful: Link is still accessible, so do a graceful shutdown process > */ > void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful); > > +/** > + * mhi_power_down_keep_dev - Power down the MHI device but keep the 'struct > + * device' for the channels associated with it. > + * This is a variant of 'mhi_power_down()' and > + * useful in scenarios such as suspend/hibernation > + * where destroying of the 'struct device' is not > + * needed. > + * @mhi_cntrl: MHI controller > + * @graceful: Link is still accessible, so do a graceful shutdown process > + */ > +void mhi_power_down_keep_dev(struct mhi_controller *mhi_cntrl, bool graceful); > + > /** > * mhi_unprepare_after_power_down - Free any allocated memory after power down > * @mhi_cntrl: MHI controller > -- > 2.25.1 >
diff --git a/drivers/bus/mhi/host/internal.h b/drivers/bus/mhi/host/internal.h index 5fe49311b8eb..aaad40a07f69 100644 --- a/drivers/bus/mhi/host/internal.h +++ b/drivers/bus/mhi/host/internal.h @@ -80,6 +80,7 @@ enum dev_st_transition { DEV_ST_TRANSITION_FP, DEV_ST_TRANSITION_SYS_ERR, DEV_ST_TRANSITION_DISABLE, + DEV_ST_TRANSITION_DISABLE_DESTROY_DEVICE, DEV_ST_TRANSITION_MAX, }; @@ -90,7 +91,8 @@ enum dev_st_transition { dev_st_trans(MISSION_MODE, "MISSION MODE") \ dev_st_trans(FP, "FLASH PROGRAMMER") \ dev_st_trans(SYS_ERR, "SYS ERROR") \ - dev_st_trans_end(DISABLE, "DISABLE") + dev_st_trans(DISABLE, "DISABLE") \ + dev_st_trans_end(DISABLE_DESTROY_DEVICE, "DISABLE (DESTROY DEVICE)") extern const char * const dev_state_tran_str[DEV_ST_TRANSITION_MAX]; #define TO_DEV_STATE_TRANS_STR(state) (((state) >= DEV_ST_TRANSITION_MAX) ? \ diff --git a/drivers/bus/mhi/host/pm.c b/drivers/bus/mhi/host/pm.c index 8b40d3f01acc..4b817b259a3e 100644 --- a/drivers/bus/mhi/host/pm.c +++ b/drivers/bus/mhi/host/pm.c @@ -468,7 +468,8 @@ static int mhi_pm_mission_mode_transition(struct mhi_controller *mhi_cntrl) } /* Handle shutdown transitions */ -static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl) +static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl, + bool destroy_device) { enum mhi_pm_state cur_state; struct mhi_event *mhi_event; @@ -530,8 +531,15 @@ static void mhi_pm_disable_transition(struct mhi_controller *mhi_cntrl) dev_dbg(dev, "Waiting for all pending threads to complete\n"); wake_up_all(&mhi_cntrl->state_event); - dev_dbg(dev, "Reset all active channels and remove MHI devices\n"); - device_for_each_child(&mhi_cntrl->mhi_dev->dev, NULL, mhi_destroy_device); + /** + * Some MHI controller drivers, ath11k as an example, would like to keep + * MHI deivces for channels during suspend/hibernation to avoid the + * probe defer issue. Add a check here to make it possible. + */ + if (destroy_device) { + dev_dbg(dev, "Reset all active channels and remove MHI devices\n"); + device_for_each_child(&mhi_cntrl->mhi_dev->dev, NULL, mhi_destroy_device); + } mutex_lock(&mhi_cntrl->pm_mutex); @@ -821,7 +829,10 @@ void mhi_pm_st_worker(struct work_struct *work) mhi_pm_sys_error_transition(mhi_cntrl); break; case DEV_ST_TRANSITION_DISABLE: - mhi_pm_disable_transition(mhi_cntrl); + mhi_pm_disable_transition(mhi_cntrl, false); + break; + case DEV_ST_TRANSITION_DISABLE_DESTROY_DEVICE: + mhi_pm_disable_transition(mhi_cntrl, true); break; default: break; @@ -1175,7 +1186,8 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl) } EXPORT_SYMBOL_GPL(mhi_async_power_up); -void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful) +static void __mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful, + bool destroy_device) { enum mhi_pm_state cur_state, transition_state; struct device *dev = &mhi_cntrl->mhi_dev->dev; @@ -1211,15 +1223,32 @@ void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful) write_unlock_irq(&mhi_cntrl->pm_lock); mutex_unlock(&mhi_cntrl->pm_mutex); - mhi_queue_state_transition(mhi_cntrl, DEV_ST_TRANSITION_DISABLE); + if (destroy_device) + mhi_queue_state_transition(mhi_cntrl, + DEV_ST_TRANSITION_DISABLE_DESTROY_DEVICE); + else + mhi_queue_state_transition(mhi_cntrl, + DEV_ST_TRANSITION_DISABLE); /* Wait for shutdown to complete */ flush_work(&mhi_cntrl->st_worker); disable_irq(mhi_cntrl->irq[0]); } + +void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful) +{ + __mhi_power_down(mhi_cntrl, graceful, true); +} EXPORT_SYMBOL_GPL(mhi_power_down); +void mhi_power_down_keep_dev(struct mhi_controller *mhi_cntrl, + bool graceful) +{ + __mhi_power_down(mhi_cntrl, graceful, false); +} +EXPORT_SYMBOL_GPL(mhi_power_down_keep_dev); + int mhi_sync_power_up(struct mhi_controller *mhi_cntrl) { int ret = mhi_async_power_up(mhi_cntrl); diff --git a/include/linux/mhi.h b/include/linux/mhi.h index 77b8c0a26674..5ce1fc1167d0 100644 --- a/include/linux/mhi.h +++ b/include/linux/mhi.h @@ -630,12 +630,28 @@ int mhi_async_power_up(struct mhi_controller *mhi_cntrl); int mhi_sync_power_up(struct mhi_controller *mhi_cntrl); /** - * mhi_power_down - Start MHI power down sequence + * mhi_power_down - Power down the MHI device and also destroy the + * 'struct device' for the channels associated with it. + * See also mhi_power_down_keep_dev() which is a variant + * of this API that keeps the 'struct device' for channels + * (useful during suspend/hibernation). * @mhi_cntrl: MHI controller * @graceful: Link is still accessible, so do a graceful shutdown process */ void mhi_power_down(struct mhi_controller *mhi_cntrl, bool graceful); +/** + * mhi_power_down_keep_dev - Power down the MHI device but keep the 'struct + * device' for the channels associated with it. + * This is a variant of 'mhi_power_down()' and + * useful in scenarios such as suspend/hibernation + * where destroying of the 'struct device' is not + * needed. + * @mhi_cntrl: MHI controller + * @graceful: Link is still accessible, so do a graceful shutdown process + */ +void mhi_power_down_keep_dev(struct mhi_controller *mhi_cntrl, bool graceful); + /** * mhi_unprepare_after_power_down - Free any allocated memory after power down * @mhi_cntrl: MHI controller
ath11k fails to resume: ath11k_pci 0000:06:00.0: timeout while waiting for restart complete This happens because when calling mhi_sync_power_up() the MHI subsystem eventually calls device_add() from mhi_create_devices() but the device creation is deferred: mhi mhi0_IPCR: Driver qcom_mhi_qrtr force probe deferral The reason for deferring device creation is explained in dpm_prepare(): /* * It is unsafe if probing of devices will happen during suspend or * hibernation and system behavior will be unpredictable in this case. * So, let's prohibit device's probing here and defer their probes * instead. The normal behavior will be restored in dpm_complete(). */ Because the device probe is deferred, the qcom_mhi_qrtr_probe() is not called and thus MHI channels are not prepared: So what this means that QRTR is not delivering messages and the QMI connection is not working between ath11k and the firmware, resulting a failure in firmware initialization. To fix this add new function mhi_power_down_keep_dev() which doesn't destroy the devices for channels during power down. This way we avoid probe defer issue and finally can get ath11k hibernation working with the following patches. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> --- drivers/bus/mhi/host/internal.h | 4 +++- drivers/bus/mhi/host/pm.c | 41 ++++++++++++++++++++++++++++----- include/linux/mhi.h | 18 ++++++++++++++- 3 files changed, 55 insertions(+), 8 deletions(-)