| Message ID | 20240417-mac_addr_at_probe-v1-6-67d6c9b3bc2b@bootlin.com (mailing list archive) |
|---|---|
| State | Deferred |
| Delegated to: | Kalle Valo |
| Headers | show |
| Series | wifi: wilc1000: fix default mac address | expand |
Hi Alexis, All Am Mi., 17. Apr. 2024 um 11:34 Uhr schrieb Alexis Lothoré <alexis.lothore@bootlin.com>: > > From: Ajay Singh <ajay.kathat@microchip.com> > > The default netdev interface exposed by WILC1000 is registered at probe, > but the chip mac address is not known until ndo_open, which will load and > start chip firmware and then retrieve stored MAC address from it. As a > consequence, the interface has uninitialized value (00:00:00:00:00) until a > user brings up the interface. > > Fix MAC address at probe by setting the following steps: > - at probe, read MAC address directly from fuse > - whenever a new netdevice is created, apply saved mac address (which can > be a user-provided address, or the eFuse Mac address if no address has > been passed by user) > - whenever an interface is brought up for the first time (and so the > firmware is loaded and started), enforce netdevice mac address to the > chip (in case user has changed it) > > Reported-by: Heiko Thiery <heiko.thiery@gmail.com> > Closes: https://lore.kernel.org/netdev/CAEyMn7aV-B4OEhHR4Ad0LM3sKCz1-nDqSb9uZNmRWR-hMZ=z+A@mail.gmail.com/T/ > Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> > Co-developed-by: Alexis Lothoré <alexis.lothore@bootlin.com> > Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> I applied the series on next and tested it on my env. It looks good. Tested-by: Heiko Thiery <heiko.thiery@gmail.com> Thank you! Heiko > --- > drivers/net/wireless/microchip/wilc1000/netdev.c | 38 ++++++++++++++---------- > drivers/net/wireless/microchip/wilc1000/sdio.c | 14 +++++++++ > drivers/net/wireless/microchip/wilc1000/spi.c | 6 ++++ > 3 files changed, 42 insertions(+), 16 deletions(-) > > diff --git a/drivers/net/wireless/microchip/wilc1000/netdev.c b/drivers/net/wireless/microchip/wilc1000/netdev.c > index 5ab448d0b643..f1fbc6e8a82a 100644 > --- a/drivers/net/wireless/microchip/wilc1000/netdev.c > +++ b/drivers/net/wireless/microchip/wilc1000/netdev.c > @@ -588,7 +588,6 @@ static int wilc_mac_open(struct net_device *ndev) > struct wilc *wl = vif->wilc; > int ret = 0; > struct mgmt_frame_regs mgmt_regs = {}; > - u8 addr[ETH_ALEN] __aligned(2); > > if (!wl || !wl->dev) { > netdev_err(ndev, "device not ready\n"); > @@ -607,25 +606,19 @@ static int wilc_mac_open(struct net_device *ndev) > return ret; > } > > - wilc_set_operation_mode(vif, wilc_get_vif_idx(vif), vif->iftype, > - vif->idx); > - > - if (is_valid_ether_addr(ndev->dev_addr)) { > - ether_addr_copy(addr, ndev->dev_addr); > - wilc_set_mac_address(vif, addr); > - } else { > - wilc_get_mac_address(vif, addr); > - eth_hw_addr_set(ndev, addr); > - } > netdev_dbg(ndev, "Mac address: %pM\n", ndev->dev_addr); > - > - if (!is_valid_ether_addr(ndev->dev_addr)) { > - netdev_err(ndev, "Wrong MAC address\n"); > + ret = wilc_set_mac_address(vif, ndev->dev_addr); > + if (ret) { > + netdev_err(ndev, "Failed to enforce MAC address in chip"); > wilc_deinit_host_int(ndev); > - wilc_wlan_deinitialize(ndev); > - return -EINVAL; > + if (!wl->open_ifcs) > + wilc_wlan_deinitialize(ndev); > + return ret; > } > > + wilc_set_operation_mode(vif, wilc_get_vif_idx(vif), vif->iftype, > + vif->idx); > + > mgmt_regs.interface_stypes = vif->mgmt_reg_stypes; > /* so we detect a change */ > vif->mgmt_reg_stypes = 0; > @@ -941,6 +934,7 @@ struct wilc_vif *wilc_netdev_ifc_init(struct wilc *wl, const char *name, > int vif_type, enum nl80211_iftype type, > bool rtnl_locked) > { > + u8 mac_address[ETH_ALEN]; > struct net_device *ndev; > struct wilc_vif *vif; > int ret; > @@ -969,6 +963,18 @@ struct wilc_vif *wilc_netdev_ifc_init(struct wilc *wl, const char *name, > vif->iftype = vif_type; > vif->idx = wilc_get_available_idx(wl); > vif->mac_opened = 0; > + > + memcpy(mac_address, wl->nv_mac_address, ETH_ALEN); > + /* WILC firmware uses locally administered MAC address for the > + * second virtual interface (bit 1 of first byte set), but > + * since it is possibly not loaded/running yet, reproduce this behavior > + * in the driver during interface creation. > + */ > + if (vif->idx) > + mac_address[0] |= 0x2; > + > + eth_hw_addr_set(vif->ndev, mac_address); > + > mutex_lock(&wl->vif_mutex); > list_add_tail_rcu(&vif->list, &wl->vif_list); > wl->vif_num += 1; > diff --git a/drivers/net/wireless/microchip/wilc1000/sdio.c b/drivers/net/wireless/microchip/wilc1000/sdio.c > index 04d6565df2cb..e6e20c86b791 100644 > --- a/drivers/net/wireless/microchip/wilc1000/sdio.c > +++ b/drivers/net/wireless/microchip/wilc1000/sdio.c > @@ -24,6 +24,9 @@ MODULE_DEVICE_TABLE(sdio, wilc_sdio_ids); > > #define WILC_SDIO_BLOCK_SIZE 512 > > +static int wilc_sdio_init(struct wilc *wilc, bool resume); > +static int wilc_sdio_deinit(struct wilc *wilc); > + > struct wilc_sdio { > bool irq_gpio; > u32 block_size; > @@ -178,6 +181,16 @@ static int wilc_sdio_probe(struct sdio_func *func, > } > clk_prepare_enable(wilc->rtc_clk); > > + wilc_sdio_init(wilc, false); > + > + ret = wilc_load_mac_from_nv(wilc); > + if (ret) { > + pr_err("Can not retrieve MAC address from chip\n"); > + goto clk_disable_unprepare; > + } > + > + wilc_sdio_deinit(wilc); > + > vif = wilc_netdev_ifc_init(wilc, "wlan%d", WILC_STATION_MODE, > NL80211_IFTYPE_STATION, false); > if (IS_ERR(vif)) { > @@ -187,6 +200,7 @@ static int wilc_sdio_probe(struct sdio_func *func, > > dev_info(&func->dev, "Driver Initializing success\n"); > return 0; > + > clk_disable_unprepare: > clk_disable_unprepare(wilc->rtc_clk); > dispose_irq: > diff --git a/drivers/net/wireless/microchip/wilc1000/spi.c b/drivers/net/wireless/microchip/wilc1000/spi.c > index add0e70a09ea..5ff940c53ad9 100644 > --- a/drivers/net/wireless/microchip/wilc1000/spi.c > +++ b/drivers/net/wireless/microchip/wilc1000/spi.c > @@ -250,6 +250,12 @@ static int wilc_bus_probe(struct spi_device *spi) > if (ret) > goto power_down; > > + ret = wilc_load_mac_from_nv(wilc); > + if (ret) { > + pr_err("Can not retrieve MAC address from chip\n"); > + goto power_down; > + } > + > wilc_wlan_power(wilc, false); > vif = wilc_netdev_ifc_init(wilc, "wlan%d", WILC_STATION_MODE, > NL80211_IFTYPE_STATION, false); > > -- > 2.44.0 >
diff --git a/drivers/net/wireless/microchip/wilc1000/netdev.c b/drivers/net/wireless/microchip/wilc1000/netdev.c index 5ab448d0b643..f1fbc6e8a82a 100644 --- a/drivers/net/wireless/microchip/wilc1000/netdev.c +++ b/drivers/net/wireless/microchip/wilc1000/netdev.c @@ -588,7 +588,6 @@ static int wilc_mac_open(struct net_device *ndev) struct wilc *wl = vif->wilc; int ret = 0; struct mgmt_frame_regs mgmt_regs = {}; - u8 addr[ETH_ALEN] __aligned(2); if (!wl || !wl->dev) { netdev_err(ndev, "device not ready\n"); @@ -607,25 +606,19 @@ static int wilc_mac_open(struct net_device *ndev) return ret; } - wilc_set_operation_mode(vif, wilc_get_vif_idx(vif), vif->iftype, - vif->idx); - - if (is_valid_ether_addr(ndev->dev_addr)) { - ether_addr_copy(addr, ndev->dev_addr); - wilc_set_mac_address(vif, addr); - } else { - wilc_get_mac_address(vif, addr); - eth_hw_addr_set(ndev, addr); - } netdev_dbg(ndev, "Mac address: %pM\n", ndev->dev_addr); - - if (!is_valid_ether_addr(ndev->dev_addr)) { - netdev_err(ndev, "Wrong MAC address\n"); + ret = wilc_set_mac_address(vif, ndev->dev_addr); + if (ret) { + netdev_err(ndev, "Failed to enforce MAC address in chip"); wilc_deinit_host_int(ndev); - wilc_wlan_deinitialize(ndev); - return -EINVAL; + if (!wl->open_ifcs) + wilc_wlan_deinitialize(ndev); + return ret; } + wilc_set_operation_mode(vif, wilc_get_vif_idx(vif), vif->iftype, + vif->idx); + mgmt_regs.interface_stypes = vif->mgmt_reg_stypes; /* so we detect a change */ vif->mgmt_reg_stypes = 0; @@ -941,6 +934,7 @@ struct wilc_vif *wilc_netdev_ifc_init(struct wilc *wl, const char *name, int vif_type, enum nl80211_iftype type, bool rtnl_locked) { + u8 mac_address[ETH_ALEN]; struct net_device *ndev; struct wilc_vif *vif; int ret; @@ -969,6 +963,18 @@ struct wilc_vif *wilc_netdev_ifc_init(struct wilc *wl, const char *name, vif->iftype = vif_type; vif->idx = wilc_get_available_idx(wl); vif->mac_opened = 0; + + memcpy(mac_address, wl->nv_mac_address, ETH_ALEN); + /* WILC firmware uses locally administered MAC address for the + * second virtual interface (bit 1 of first byte set), but + * since it is possibly not loaded/running yet, reproduce this behavior + * in the driver during interface creation. + */ + if (vif->idx) + mac_address[0] |= 0x2; + + eth_hw_addr_set(vif->ndev, mac_address); + mutex_lock(&wl->vif_mutex); list_add_tail_rcu(&vif->list, &wl->vif_list); wl->vif_num += 1; diff --git a/drivers/net/wireless/microchip/wilc1000/sdio.c b/drivers/net/wireless/microchip/wilc1000/sdio.c index 04d6565df2cb..e6e20c86b791 100644 --- a/drivers/net/wireless/microchip/wilc1000/sdio.c +++ b/drivers/net/wireless/microchip/wilc1000/sdio.c @@ -24,6 +24,9 @@ MODULE_DEVICE_TABLE(sdio, wilc_sdio_ids); #define WILC_SDIO_BLOCK_SIZE 512 +static int wilc_sdio_init(struct wilc *wilc, bool resume); +static int wilc_sdio_deinit(struct wilc *wilc); + struct wilc_sdio { bool irq_gpio; u32 block_size; @@ -178,6 +181,16 @@ static int wilc_sdio_probe(struct sdio_func *func, } clk_prepare_enable(wilc->rtc_clk); + wilc_sdio_init(wilc, false); + + ret = wilc_load_mac_from_nv(wilc); + if (ret) { + pr_err("Can not retrieve MAC address from chip\n"); + goto clk_disable_unprepare; + } + + wilc_sdio_deinit(wilc); + vif = wilc_netdev_ifc_init(wilc, "wlan%d", WILC_STATION_MODE, NL80211_IFTYPE_STATION, false); if (IS_ERR(vif)) { @@ -187,6 +200,7 @@ static int wilc_sdio_probe(struct sdio_func *func, dev_info(&func->dev, "Driver Initializing success\n"); return 0; + clk_disable_unprepare: clk_disable_unprepare(wilc->rtc_clk); dispose_irq: diff --git a/drivers/net/wireless/microchip/wilc1000/spi.c b/drivers/net/wireless/microchip/wilc1000/spi.c index add0e70a09ea..5ff940c53ad9 100644 --- a/drivers/net/wireless/microchip/wilc1000/spi.c +++ b/drivers/net/wireless/microchip/wilc1000/spi.c @@ -250,6 +250,12 @@ static int wilc_bus_probe(struct spi_device *spi) if (ret) goto power_down; + ret = wilc_load_mac_from_nv(wilc); + if (ret) { + pr_err("Can not retrieve MAC address from chip\n"); + goto power_down; + } + wilc_wlan_power(wilc, false); vif = wilc_netdev_ifc_init(wilc, "wlan%d", WILC_STATION_MODE, NL80211_IFTYPE_STATION, false);