@@ -132,7 +132,9 @@ static int ath12k_dp_srng_find_ring_in_mask(int ring_num, const u8 *grp_mask)
static int ath12k_dp_srng_calculate_msi_group(struct ath12k_base *ab,
enum hal_ring_type type, int ring_num)
{
+ const struct ath12k_hal_tcl_to_wbm_rbm_map *map;
const u8 *grp_mask;
+ int i;
switch (type) {
case HAL_WBM2SW_RELEASE:
@@ -140,6 +142,14 @@ static int ath12k_dp_srng_calculate_msi_group(struct ath12k_base *ab,
grp_mask = &ab->hw_params->ring_mask->rx_wbm_rel[0];
ring_num = 0;
} else {
+ map = ab->hw_params->hal_ops->tcl_to_wbm_rbm_map;
+ for (i = 0; i < ab->hw_params->max_tx_ring; i++) {
+ if (ring_num == map[i].wbm_ring_num) {
+ ring_num = i;
+ break;
+ }
+ }
+
grp_mask = &ab->hw_params->ring_mask->tx[0];
}
break;
@@ -883,11 +893,9 @@ int ath12k_dp_service_srng(struct ath12k_base *ab,
enum dp_monitor_mode monitor_mode;
u8 ring_mask;
- while (i < ab->hw_params->max_tx_ring) {
- if (ab->hw_params->ring_mask->tx[grp_id] &
- BIT(ab->hw_params->hal_ops->tcl_to_wbm_rbm_map[i].wbm_ring_num))
- ath12k_dp_tx_completion_handler(ab, i);
- i++;
+ if (ab->hw_params->ring_mask->tx[grp_id]) {
+ i = fls(ab->hw_params->ring_mask->tx[grp_id]) - 1;
+ ath12k_dp_tx_completion_handler(ab, i);
}
if (ab->hw_params->ring_mask->rx_err[grp_id]) {
@@ -580,8 +580,8 @@ static const struct ath12k_hw_ring_mask ath12k_hw_ring_mask_qcn9274 = {
static const struct ath12k_hw_ring_mask ath12k_hw_ring_mask_wcn7850 = {
.tx = {
ATH12K_TX_RING_MASK_0,
+ ATH12K_TX_RING_MASK_1,
ATH12K_TX_RING_MASK_2,
- ATH12K_TX_RING_MASK_4,
},
.rx_mon_dest = {
},
We observe intermittent ping failures from the access point (AP) to station (STA) in any mode(AP-STA or Mesh) configured. Specifically, the transmission completion status is not received at Tx completion ring id-4(WBM2SW ring4) for the packets transmitted via TCL DATA ring id-3. This prevents freeing up Tx descriptors and leads to buffer exhaustion. Currently, during initialization of the WBM2SW ring, we are directly mapping the ring number to the ring mask to obtain the ring mask group index. This approach is causing setup failures for WBM2SW ring-4. Similarly, during runtime, when receiving incoming transmission completion status, the validation of the ring number by mapping the interrupted ring mask. This is resulting in validation failure. Thereby preventing entry into the completion handler(ath12k_dp_tx_completion_handler()). The existing design assumed that the ring numbers would always be sequential and could be directly mapped with the ring mask. However, this assumption does not hold true for WBM2SW ring-4. Therefore, modify the design such that, instead of mapping the ring number, the ring ID is mapped with the ring mask. According to this design: 1. During initialization of the WBM2SW ring, mapping the ring ID to the ring mask will ensure obtaining the correct ring mask group ID. 2. During runtime, validating the interrupted ring mask group ID within the transmission completion group is sufficient. This approach allows the ring ID to be derived from the interrupted ring mask and enables entry into the completion handler. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com> --- drivers/net/wireless/ath/ath12k/dp.c | 18 +++++++++++++----- drivers/net/wireless/ath/ath12k/hw.c | 2 +- 2 files changed, 14 insertions(+), 6 deletions(-) base-commit: 2c4d8e19cf060744a9db466ffbaea13ab37f25ca