@@ -78,11 +78,11 @@ config B43_SDIO
If unsure, say N.
-# Data transfers to the device via PIO
-# This is only needed on PCMCIA and SDIO devices. All others can do DMA properly.
+# Data transfers to the device via PIO. We want it as a fallback even
+# if we can do DMA.
config B43_PIO
bool
- depends on B43 && (B43_SDIO || B43_PCMCIA || B43_FORCE_PIO)
+ depends on B43
select SSB_BLOCKIO
default y
@@ -694,6 +694,7 @@ struct b43_wldev {
bool radio_hw_enable; /* saved state of radio hardware enabled state */
bool qos_enabled; /* TRUE, if QoS is used. */
bool hwcrypto_enabled; /* TRUE, if HW crypto acceleration is enabled. */
+ bool use_pio; /* TRUE if next init should use PIO */
/* PHY/Radio device. */
struct b43_phy phy;
@@ -885,9 +886,9 @@ static inline bool b43_using_pio_transfers(struct b43_wldev *dev)
}
#ifdef CONFIG_B43_FORCE_PIO
-# define B43_FORCE_PIO 1
+# define B43_PIO_DEFAULT 1
#else
-# define B43_FORCE_PIO 0
+# define B43_PIO_DEFAULT 0
#endif
@@ -98,6 +98,10 @@ static int modparam_btcoex = 1;
module_param_named(btcoex, modparam_btcoex, int, 0444);
MODULE_PARM_DESC(btcoex, "Enable Bluetooth coexistence (default on)");
+int b43_modparam_pio = B43_PIO_DEFAULT;
+module_param_named(pio, b43_modparam_pio, int, 0644);
+MODULE_PARM_DESC(pio, "Use PIO accesses by default: 0=DMA, 1=PIO");
+
int b43_modparam_verbose = B43_VERBOSITY_DEFAULT;
module_param_named(verbose, b43_modparam_verbose, int, 0644);
MODULE_PARM_DESC(verbose, "Log message verbosity: 0=error, 1=warn, 2=info(default), 3=debug");
@@ -1795,6 +1799,9 @@ static void b43_do_interrupt_thread(struct b43_wldev *dev)
"on your system. Please use PIO instead.\n");
b43err(dev->wl, "CONFIG_B43_FORCE_PIO must be set in "
"your kernel configuration.\n");
+ /* Fall back to PIO transfers if we get fatal DMA errors! */
+ dev->use_pio = 1;
+ b43_controller_restart(dev, "DMA error");
return;
}
if (merged_dma_reason & B43_DMAIRQ_NONFATALMASK) {
@@ -4360,7 +4367,7 @@ static int b43_wireless_core_init(struct b43_wldev *dev)
if ((dev->dev->bus->bustype == SSB_BUSTYPE_PCMCIA) ||
(dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) ||
- B43_FORCE_PIO) {
+ dev->use_pio) {
dev->__using_pio_transfers = 1;
err = b43_pio_init(dev);
} else {
@@ -4830,6 +4837,7 @@ static int b43_one_core_attach(struct ssb_device *dev, struct b43_wl *wl)
if (!wldev)
goto out;
+ wldev->use_pio = b43_modparam_pio;
wldev->dev = dev;
wldev->wl = wl;
b43_set_status(wldev, B43_STAT_UNINIT);