@@ -11,26 +11,6 @@
#include "wil6210.h"
-static int wil_ethtoolops_begin(struct net_device *ndev)
-{
- struct wil6210_priv *wil = ndev_to_wil(ndev);
-
- mutex_lock(&wil->mutex);
-
- wil_dbg_misc(wil, "ethtoolops_begin\n");
-
- return 0;
-}
-
-static void wil_ethtoolops_complete(struct net_device *ndev)
-{
- struct wil6210_priv *wil = ndev_to_wil(ndev);
-
- wil_dbg_misc(wil, "ethtoolops_complete\n");
-
- mutex_unlock(&wil->mutex);
-}
-
static int wil_ethtoolops_get_coalesce(struct net_device *ndev,
struct ethtool_coalesce *cp)
{
@@ -39,11 +19,12 @@ static int wil_ethtoolops_get_coalesce(struct net_device *ndev,
u32 rx_itr_en, rx_itr_val = 0;
int ret;
+ mutex_lock(&wil->mutex);
wil_dbg_misc(wil, "ethtoolops_get_coalesce\n");
ret = wil_pm_runtime_get(wil);
if (ret < 0)
- return ret;
+ goto out;
tx_itr_en = wil_r(wil, RGF_DMA_ITR_TX_CNT_CTL);
if (tx_itr_en & BIT_DMA_ITR_TX_CNT_CTL_EN)
@@ -57,7 +38,11 @@ static int wil_ethtoolops_get_coalesce(struct net_device *ndev,
cp->tx_coalesce_usecs = tx_itr_val;
cp->rx_coalesce_usecs = rx_itr_val;
- return 0;
+ ret = 0;
+
+out:
+ mutex_unlock(&wil->mutex);
+ return ret;
}
static int wil_ethtoolops_set_coalesce(struct net_device *ndev,
@@ -67,12 +52,14 @@ static int wil_ethtoolops_set_coalesce(struct net_device *ndev,
struct wireless_dev *wdev = ndev->ieee80211_ptr;
int ret;
+ mutex_lock(&wil->mutex);
wil_dbg_misc(wil, "ethtoolops_set_coalesce: rx %d usec, tx %d usec\n",
cp->rx_coalesce_usecs, cp->tx_coalesce_usecs);
if (wdev->iftype == NL80211_IFTYPE_MONITOR) {
wil_dbg_misc(wil, "No IRQ coalescing in monitor mode\n");
- return -EINVAL;
+ ret = -EINVAL;
+ goto out;
}
/* only @rx_coalesce_usecs and @tx_coalesce_usecs supported,
@@ -88,24 +75,26 @@ static int wil_ethtoolops_set_coalesce(struct net_device *ndev,
ret = wil_pm_runtime_get(wil);
if (ret < 0)
- return ret;
+ goto out;
wil->txrx_ops.configure_interrupt_moderation(wil);
wil_pm_runtime_put(wil);
+ ret = 0;
- return 0;
+out:
+ mutex_unlock(&wil->mutex);
+ return ret;
out_bad:
wil_dbg_misc(wil, "Unsupported coalescing params. Raw command:\n");
print_hex_dump_debug("DBG[MISC] coal ", DUMP_PREFIX_OFFSET, 16, 4,
cp, sizeof(*cp), false);
+ mutex_unlock(&wil->mutex);
return -EINVAL;
}
static const struct ethtool_ops wil_ethtool_ops = {
- .begin = wil_ethtoolops_begin,
- .complete = wil_ethtoolops_complete,
.get_drvinfo = cfg80211_get_drvinfo,
.get_coalesce = wil_ethtoolops_get_coalesce,
.set_coalesce = wil_ethtoolops_set_coalesce,
The wil6210 driver locks a mutex in begin() ethtool_ops callback and unlocks it in complete() so that all ethtool requests are serialized. This is not going to work correctly with netlink interface; e.g. when ioctl triggers a netlink notification, netlink code would call begin() again while the mutex taken by ioctl code is still held by the same task. Let's get rid of the begin() and complete() callbacks and move the mutex locking into the remaining ethtool_ops handlers except get_drvinfo which only copies strings that are not changing so that there is no need for serialization. Signed-off-by: Michal Kubecek <mkubecek@suse.cz> --- drivers/net/wireless/ath/wil6210/ethtool.c | 43 ++++++++-------------- 1 file changed, 16 insertions(+), 27 deletions(-)