diff mbox series

[RFC,net-next,06/22] net: dsa: mt7530: improve code path for setting up port 5

Message ID 20230421143648.87889-7-arinc.unal@arinc9.com (mailing list archive)
State Superseded
Delegated to: Netdev Maintainers
Headers show
Series net: dsa: MT7530, MT7531, and MT7988 improvements | expand

Checks

Context Check Description
netdev/series_format fail Series longer than 15 patches (and no cover letter)
netdev/tree_selection success Clearly marked for net-next
netdev/fixes_present success Fixes tag not required for -next series
netdev/header_inline success No static functions without inline keyword in header files
netdev/build_32bit success Errors and warnings before: 8 this patch: 8
netdev/cc_maintainers success CCed 17 of 17 maintainers
netdev/build_clang success Errors and warnings before: 8 this patch: 8
netdev/verify_signedoff success Signed-off-by tag matches author and committer
netdev/deprecated_api success None detected
netdev/check_selftest success No net selftest shell script
netdev/verify_fixes success No Fixes tag
netdev/build_allmodconfig_warn success Errors and warnings before: 8 this patch: 8
netdev/checkpatch success total: 0 errors, 0 warnings, 0 checks, 46 lines checked
netdev/kdoc success Errors and warnings before: 0 this patch: 0
netdev/source_inline success Was 0 now: 0

Commit Message

Arınç ÜNAL April 21, 2023, 2:36 p.m. UTC 
From: Arınç ÜNAL <arinc.unal@arinc9.com>

There're two code paths for setting up port 5:

mt7530_setup()
-> mt7530_setup_port5()

mt753x_phylink_mac_config()
-> mt753x_mac_config()
   -> mt7530_mac_config()
      -> mt7530_setup_port5()

Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
is used as a CPU, DSA, or user port, mt7530_setup_port5() from
mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
set on mt7530_setup_port5() will match state->interface on
mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
again.

mt7530_setup_port5() from mt753x_phylink_mac_config() won't run when port 5
is disabled or used for PHY muxing as port 5 won't be defined on the
devicetree.

Therefore, mt7530_setup_port5() will never run from
mt753x_phylink_mac_config().

Address this by not running mt7530_setup_port5() from mt7530_setup() if
port 5 is used as a CPU, DSA, or user port. For the cases of PHY muxing or
the port being disabled, call mt7530_setup_port5() from mt7530_setup().

Do not set priv->p5_interface on mt7530_setup_port5(). There won't be a
case where mt753x_phylink_mac_config() runs after mt7530_setup_port5()
anymore.

Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
"priv" is allocated.

Move setting the interface to a more specific location. It's supposed to be
overwritten if PHY muxing is detected.

Improve the comment which explain the process.

Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
---
 drivers/net/dsa/mt7530.c | 19 ++++++++-----------
 1 file changed, 8 insertions(+), 11 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 30553044d4b7..591df09c8bb5 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -968,8 +968,6 @@  static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
 	dev_dbg(ds->dev, "Setup P5, HWTRAP=0x%x, intf_sel=%s, phy-mode=%s\n",
 		val, p5_intf_modes(priv->p5_intf_sel), phy_modes(interface));
 
-	priv->p5_interface = interface;
-
 unlock_exit:
 	mutex_unlock(&priv->reg_mutex);
 }
@@ -2277,16 +2275,15 @@  mt7530_setup(struct dsa_switch *ds)
 		return ret;
 
 	/* Setup port 5 */
-	priv->p5_intf_sel = P5_DISABLED;
-	interface = PHY_INTERFACE_MODE_NA;
-
 	if (!dsa_is_unused_port(ds, 5)) {
 		priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
-		ret = of_get_phy_mode(dsa_to_port(ds, 5)->dn, &interface);
-		if (ret && ret != -ENODEV)
-			return ret;
 	} else {
-		/* Scan the ethernet nodes. look for GMAC1, lookup used phy */
+		/* Scan the ethernet nodes. Look for GMAC1, lookup the used PHY.
+		 * Set priv->p5_intf_sel to the appropriate value if PHY muxing
+		 * is detected.
+		 */
+		interface = PHY_INTERFACE_MODE_NA;
+
 		for_each_child_of_node(dn, mac_np) {
 			if (!of_device_is_compatible(mac_np,
 						     "mediatek,eth-mac"))
@@ -2317,6 +2314,8 @@  mt7530_setup(struct dsa_switch *ds)
 			of_node_put(phy_node);
 			break;
 		}
+
+		mt7530_setup_port5(ds, interface);
 	}
 
 #ifdef CONFIG_GPIOLIB
@@ -2327,8 +2326,6 @@  mt7530_setup(struct dsa_switch *ds)
 	}
 #endif /* CONFIG_GPIOLIB */
 
-	mt7530_setup_port5(ds, interface);
-
 	/* Flush the FDB table */
 	ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
 	if (ret < 0)