diff mbox series

[1/2] dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe Phy controller

Message ID 1534227134-151584-2-git-send-email-hanjie.lin@amlogic.com (mailing list archive)
State Superseded
Headers show
Series add the Amlogic Meson PCIe phy driver. | expand

Commit Message

Hanjie Lin Aug. 14, 2018, 6:12 a.m. UTC
From: Yue Wang <yue.wang@amlogic.com>

The Meson-PCIE-PHY controller supports the 5-Gbps data rate
of the PCI Express Gen 2 specification and is backwardcompatible
with the 2.5-Gbps Gen 1.1 specification with only
inferred idle detection supported on AMLOGIC SoCs.

Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
---
 .../bindings/phy/amlogic,meson-pcie-phy.txt        | 31 ++++++++++++++++++++++
 1 file changed, 31 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt

Comments

Rob Herring (Arm) Aug. 14, 2018, 10:50 p.m. UTC | #1
On Tue, Aug 14, 2018 at 02:12:13AM -0400, Hanjie Lin wrote:
> From: Yue Wang <yue.wang@amlogic.com>

Subject should be "dt-bindings: phy: ..."

> The Meson-PCIE-PHY controller supports the 5-Gbps data rate
> of the PCI Express Gen 2 specification and is backwardcompatible

space                                                   ^

> with the 2.5-Gbps Gen 1.1 specification with only
> inferred idle detection supported on AMLOGIC SoCs.

AMLOGIC or Amlogic? 

> 
> Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
> Signed-off-by: Yue Wang <yue.wang@amlogic.com>
> ---
>  .../bindings/phy/amlogic,meson-pcie-phy.txt        | 31 ++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
> 
> diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
> new file mode 100644
> index 0000000..db99085
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
> @@ -0,0 +1,31 @@
> +* Amlogic Meson AXG PCIE PHY binding
> +
> +Required properties:
> +- compatible:	Should be
> +	- "amlogic,axg-pcie-phy"
> +- #phys-cells:	must be 0 (see phy-bindings.txt in this directory)

You don't need to distinguish port A and B?

> +- reg:		The base address and length of the registers
> +- resets:	phandle to the reset lines
> +- reset-names:	must contain "phy" and "peripheral"
> +	- "port_a" Port A reset
> +	- "port_b" Port B reset
> +	- "phy"	PHY reset
> +	- "apb"	APB reset
> +Optional properties:
> +- phy-supply:	see phy-bindings.txt in this directory
> +
> +Example:
> +	pcie_phy: pcie-phy@ff644000 {
> +		#phy-cells = <0>;
> +		compatible = "amlogic,axg-pcie-phy";
> +		reg = <0x0 0xff644000 0x0 0x2000>;
> +		resets = <&reset RESET_PCIE_A>,
> +				<&reset RESET_PCIE_B>,
> +				<&reset RESET_PCIE_PHY>,
> +				<&reset RESET_PCIE_APB>;
> +		reset-names =
> +				"port_a",
> +				"port_b",
> +				"phy",
> +				"apb";
> +	};
> -- 
> 2.7.4
>
Hanjie Lin Aug. 16, 2018, 3:01 a.m. UTC | #2
On 2018/8/15 6:50, Rob Herring wrote:
> On Tue, Aug 14, 2018 at 02:12:13AM -0400, Hanjie Lin wrote:
>> From: Yue Wang <yue.wang@amlogic.com>
> 
> Subject should be "dt-bindings: phy: ..."
> 
>> The Meson-PCIE-PHY controller supports the 5-Gbps data rate
>> of the PCI Express Gen 2 specification and is backwardcompatible
> 
> space    

yes, I will fix
                                               ^
> 
>> with the 2.5-Gbps Gen 1.1 specification with only
>> inferred idle detection supported on AMLOGIC SoCs.
> 
> AMLOGIC or Amlogic? 
> 

yes, we will stick to 'Amlogic'

>>
>> Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
>> Signed-off-by: Yue Wang <yue.wang@amlogic.com>
>> ---
>>  .../bindings/phy/amlogic,meson-pcie-phy.txt        | 31 ++++++++++++++++++++++
>>  1 file changed, 31 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
>>
>> diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
>> new file mode 100644
>> index 0000000..db99085
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
>> @@ -0,0 +1,31 @@
>> +* Amlogic Meson AXG PCIE PHY binding
>> +
>> +Required properties:
>> +- compatible:	Should be
>> +	- "amlogic,axg-pcie-phy"
>> +- #phys-cells:	must be 0 (see phy-bindings.txt in this directory)
> 
> You don't need to distinguish port A and B?

No, we don't. Theoretically there is only one phy in the chip,
and we have distinguished ports by reset lines.

Thanks for all corrections and suggestions.

> 
>> +- reg:		The base address and length of the registers
>> +- resets:	phandle to the reset lines
>> +- reset-names:	must contain "phy" and "peripheral"
>> +	- "port_a" Port A reset
>> +	- "port_b" Port B reset
>> +	- "phy"	PHY reset
>> +	- "apb"	APB reset
>> +Optional properties:
>> +- phy-supply:	see phy-bindings.txt in this directory
>> +
>> +Example:
>> +	pcie_phy: pcie-phy@ff644000 {
>> +		#phy-cells = <0>;
>> +		compatible = "amlogic,axg-pcie-phy";
>> +		reg = <0x0 0xff644000 0x0 0x2000>;
>> +		resets = <&reset RESET_PCIE_A>,
>> +				<&reset RESET_PCIE_B>,
>> +				<&reset RESET_PCIE_PHY>,
>> +				<&reset RESET_PCIE_APB>;
>> +		reset-names =
>> +				"port_a",
>> +				"port_b",
>> +				"phy",
>> +				"apb";
>> +	};
>> -- 
>> 2.7.4
>>
> 
> .
>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
new file mode 100644
index 0000000..db99085
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
@@ -0,0 +1,31 @@ 
+* Amlogic Meson AXG PCIE PHY binding
+
+Required properties:
+- compatible:	Should be
+	- "amlogic,axg-pcie-phy"
+- #phys-cells:	must be 0 (see phy-bindings.txt in this directory)
+- reg:		The base address and length of the registers
+- resets:	phandle to the reset lines
+- reset-names:	must contain "phy" and "peripheral"
+	- "port_a" Port A reset
+	- "port_b" Port B reset
+	- "phy"	PHY reset
+	- "apb"	APB reset
+Optional properties:
+- phy-supply:	see phy-bindings.txt in this directory
+
+Example:
+	pcie_phy: pcie-phy@ff644000 {
+		#phy-cells = <0>;
+		compatible = "amlogic,axg-pcie-phy";
+		reg = <0x0 0xff644000 0x0 0x2000>;
+		resets = <&reset RESET_PCIE_A>,
+				<&reset RESET_PCIE_B>,
+				<&reset RESET_PCIE_PHY>,
+				<&reset RESET_PCIE_APB>;
+		reset-names =
+				"port_a",
+				"port_b",
+				"phy",
+				"apb";
+	};