Message ID | 20231214072839.2367-1-minda.chen@starfivetech.com (mailing list archive) |
---|---|
Headers | show |
Series | Refactoring Microchip PCIe driver and add StarFive PCIe | expand |
Minda Chen <minda.chen@starfivetech.com> writes: > This patchset final purpose is add PCIe driver for StarFive JH7110 SoC. > JH7110 using PLDA XpressRICH PCIe IP. Microchip PolarFire Using the > same IP and have commit their codes, which are mixed with PLDA > controller codes and Microchip platform codes. Thank you for this series. I tested this on a VisionFive v2 board, and it seems to probe and find my M.2 NVMe SSD, but then gets timeouts when trying to use the NVMe (e.g. 'blkid' command) Kernel logs below. Kevin [ 15.131094] pcie-starfive 9c0000000.pcie: host bridge /soc/pcie@9c0000000 ranges: [ 15.138637] pcie-starfive 9c0000000.pcie: MEM 0x0038000000..0x003fffffff -> 0x0038000000 [ 15.147180] pcie-starfive 9c0000000.pcie: MEM 0x0980000000..0x09bfffffff -> 0x0980000000 [ 15.368040] pcie-starfive 9c0000000.pcie: port link up [ 15.374219] pcie-starfive 9c0000000.pcie: PCI host bridge to bus 0001:00 [ 15.380944] pci_bus 0001:00: root bus resource [bus 00-ff] [ 15.386443] pci_bus 0001:00: root bus resource [mem 0x38000000-0x3fffffff] [ 15.393330] pci_bus 0001:00: root bus resource [mem 0x980000000-0x9bfffffff pref] [ 15.400882] pci 0001:00:00.0: [1556:1111] type 01 class 0x060400 [ 15.407165] pci 0001:00:00.0: supports D1 D2 [ 15.411447] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 15.419964] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 15.428245] pci 0001:01:00.0: [126f:2263] type 00 class 0x010802 [ 15.434331] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 15.441578] pci 0001:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0001:00:00.0 (capable of 31.504 Gb/s with 8 .0 GT/s PCIe x4 link) [ 15.456910] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 15.463553] pci 0001:00:00.0: BAR 8: assigned [mem 0x38000000-0x380fffff] [ 15.470352] pci 0001:01:00.0: BAR 0: assigned [mem 0x38000000-0x38003fff 64bit] [ 15.477699] pci 0001:00:00.0: PCI bridge to [bus 01] [ 15.482686] pci 0001:00:00.0: bridge window [mem 0x38000000-0x380fffff] [ 15.489632] pcieport 0001:00:00.0: enabling device (0000 -> 0002) [ 15.496038] pcieport 0001:00:00.0: PME: Signaling with IRQ 56 [ 15.502472] usb 1-1: new high-speed USB device number 2 using xhci_hcd [ 15.509755] usb usb2-port2: over-current condition [ 15.515883] nvme nvme0: pci function 0001:01:00.0 [ 15.520615] nvme 0001:01:00.0: enabling device (0000 -> 0002) [ 15.532685] nvme nvme0: allocated 64 MiB host memory buffer. [ 15.550070] nvme nvme0: 4/0/0 default/read/poll queues [ 15.562992] nvme nvme0: Ignoring bogus Namespace Identifiers [ 15.663327] hub 1-1:1.0: USB hub found [ 15.667320] hub 1-1:1.0: 4 ports detected [ 46.064052] nvme nvme0: I/O 424 QID 3 timeout, completion polled [ 76.784046] nvme nvme0: I/O 425 (I/O Cmd) QID 3 timeout, aborting [ 76.790179] nvme nvme0: I/O 426 (I/O Cmd) QID 3 timeout, aborting [ 76.796294] nvme nvme0: I/O 427 (I/O Cmd) QID 3 timeout, aborting [ 76.802411] nvme nvme0: I/O 428 (I/O Cmd) QID 3 timeout, aborting [ 76.808525] nvme nvme0: I/O 429 (I/O Cmd) QID 3 timeout, aborting
> Minda Chen <minda.chen@starfivetech.com> writes: > > > This patchset final purpose is add PCIe driver for StarFive JH7110 SoC. > > JH7110 using PLDA XpressRICH PCIe IP. Microchip PolarFire Using the > > same IP and have commit their codes, which are mixed with PLDA > > controller codes and Microchip platform codes. > > Thank you for this series. > > I tested this on a VisionFive v2 board, and it seems to probe and find my > M.2 NVMe SSD, but then gets timeouts when trying to use the NVMe (e.g. > 'blkid' command) > Hi, Kevin: Could you please provide the manufacturer and model of the M.2 NVMe SSD you tested? > Kernel logs below. > > Kevin > > [ 15.131094] pcie-starfive 9c0000000.pcie: host bridge > /soc/pcie@9c0000000 ranges: > [ 15.138637] pcie-starfive 9c0000000.pcie: MEM > 0x0038000000..0x003fffffff -> 0x0038000000 > [ 15.147180] pcie-starfive 9c0000000.pcie: MEM > 0x0980000000..0x09bfffffff -> 0x0980000000 > [ 15.368040] pcie-starfive 9c0000000.pcie: port link up > [ 15.374219] pcie-starfive 9c0000000.pcie: PCI host bridge to bus 0001:00 > [ 15.380944] pci_bus 0001:00: root bus resource [bus 00-ff] > [ 15.386443] pci_bus 0001:00: root bus resource [mem > 0x38000000-0x3fffffff] > [ 15.393330] pci_bus 0001:00: root bus resource [mem > 0x980000000-0x9bfffffff pref] > [ 15.400882] pci 0001:00:00.0: [1556:1111] type 01 class 0x060400 > [ 15.407165] pci 0001:00:00.0: supports D1 D2 > [ 15.411447] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot > D3cold > [ 15.419964] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), > reconfiguring > [ 15.428245] pci 0001:01:00.0: [126f:2263] type 00 class 0x010802 > [ 15.434331] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff > 64bit] > [ 15.441578] pci 0001:01:00.0: 4.000 Gb/s available PCIe bandwidth, > limited by 5.0 GT/s PCIe x1 link at 0001:00:00.0 (capable of 31.504 Gb/s with > 8 > .0 GT/s PCIe x4 link) > [ 15.456910] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 > [ 15.463553] pci 0001:00:00.0: BAR 8: assigned [mem > 0x38000000-0x380fffff] > [ 15.470352] pci 0001:01:00.0: BAR 0: assigned [mem > 0x38000000-0x38003fff 64bit] > [ 15.477699] pci 0001:00:00.0: PCI bridge to [bus 01] > [ 15.482686] pci 0001:00:00.0: bridge window [mem > 0x38000000-0x380fffff] > [ 15.489632] pcieport 0001:00:00.0: enabling device (0000 -> 0002) > [ 15.496038] pcieport 0001:00:00.0: PME: Signaling with IRQ 56 > [ 15.502472] usb 1-1: new high-speed USB device number 2 using xhci_hcd > [ 15.509755] usb usb2-port2: over-current condition > [ 15.515883] nvme nvme0: pci function 0001:01:00.0 > [ 15.520615] nvme 0001:01:00.0: enabling device (0000 -> 0002) > [ 15.532685] nvme nvme0: allocated 64 MiB host memory buffer. > [ 15.550070] nvme nvme0: 4/0/0 default/read/poll queues > [ 15.562992] nvme nvme0: Ignoring bogus Namespace Identifiers > [ 15.663327] hub 1-1:1.0: USB hub found > [ 15.667320] hub 1-1:1.0: 4 ports detected > > [ 46.064052] nvme nvme0: I/O 424 QID 3 timeout, completion polled > > [ 76.784046] nvme nvme0: I/O 425 (I/O Cmd) QID 3 timeout, aborting > [ 76.790179] nvme nvme0: I/O 426 (I/O Cmd) QID 3 timeout, aborting > [ 76.796294] nvme nvme0: I/O 427 (I/O Cmd) QID 3 timeout, aborting > [ 76.802411] nvme nvme0: I/O 428 (I/O Cmd) QID 3 timeout, aborting > [ 76.808525] nvme nvme0: I/O 429 (I/O Cmd) QID 3 timeout, aborting
Kevin Xie <kevin.xie@starfivetech.com> writes: >> Minda Chen <minda.chen@starfivetech.com> writes: >> >> > This patchset final purpose is add PCIe driver for StarFive JH7110 SoC. >> > JH7110 using PLDA XpressRICH PCIe IP. Microchip PolarFire Using the >> > same IP and have commit their codes, which are mixed with PLDA >> > controller codes and Microchip platform codes. >> >> Thank you for this series. >> >> I tested this on a VisionFive v2 board, and it seems to probe and find my >> M.2 NVMe SSD, but then gets timeouts when trying to use the NVMe (e.g. >> 'blkid' command) >> > > Hi, Kevin: > Could you please provide the manufacturer and model of the M.2 NVMe SSD > you tested? I have a 256 Gb Silicon Power P34A60 M.2 NVMe SSD (part number: sp256gbp34a60m28) Also for reference, I tested the same SSD on another arm platform (Khadas VIM3) and it works fine. Kevin