| Message ID | 20230922115116.2748804-5-srichara@win-platform-upstream01.qualcomm.com (mailing list archive) |
|---|---|
| State | New |
| Delegated to: | Daniel Lezcano |
| Headers | show |
| Series | Add support for IPQ5018 tsens | expand |
On Fri, 22 Sept 2023 at 14:51, Sricharan R <srichara@win-platform-upstream01.qualcomm.com> wrote: > > From: Sricharan Ramabadhran <quic_srichara@quicinc.com> > > IPQ5018 has tsens V1.0 IP with 4 sensors. > There is no RPM, so tsens has to be manually enabled. Adding the tsens > and nvmem node and IPQ5018 has 4 thermal sensors (zones). With the > critical temperature being 120'C and action is to reboot. Adding all > the 4 zones here. > > Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> > --- > [v3] Ordered the qfprom device node properties as per > Krzysztof's comments > > arch/arm64/boot/dts/qcom/ipq5018.dtsi | 169 ++++++++++++++++++++++++++ > 1 file changed, 169 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > index 9f13d2dcdfd5..9e28b54ebcbd 100644 > --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi > +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > @@ -93,6 +93,117 @@ soc: soc@0 { > #size-cells = <1>; > ranges = <0 0 0 0xffffffff>; > > + qfprom: qfprom@a0000 { > + compatible = "qcom,ipq5018-qfprom", "qcom,qfprom"; > + reg = <0xa0000 0x1000>; > + #address-cells = <1>; > + #size-cells = <1>; > + > + tsens_base1: base1@249 { > + reg = <0x249 2>; > + bits = <3 8>; > + }; > + > + tsens_base2: base2@24a { > + reg = <0x24a 2>; > + bits = <3 8>; > + }; Sort by the address, please, as usual. > + > + tsens_mode: mode@249 { > + reg = <0x249 1>; > + bits = <0 3>; > + }; > + > + tsens_s0_p1: s0-p1@24b { > + reg = <0x24b 0x2>; > + bits = <2 6>; > + }; > + > + tsens_s0_p2: s0-p2@24c { > + reg = <0x24c 0x1>; > + bits = <1 6>; > + }; > + > + tsens_s1_p1: s1-p1@24c { > + reg = <0x24c 0x2>; > + bits = <7 6>; > + }; > + > + tsens_s1_p2: s1-p2@24d { > + reg = <0x24d 0x2>; > + bits = <5 6>; > + }; > + > + tsens_s2_p1: s2-p1@24e { > + reg = <0x24e 0x2>; > + bits = <3 6>; > + }; > + > + tsens_s2_p2: s2-p2@24f { > + reg = <0x24f 0x1>; > + bits = <1 6>; > + }; > + > + tsens_s3_p1: s3-p1@24f { > + reg = <0x24f 0x2>; > + bits = <7 6>; > + }; > + > + tsens_s3_p2: s3-p2@250 { > + reg = <0x250 0x2>; > + bits = <5 6>; > + }; > + > + tsens_s4_p1: s4-p1@251 { > + reg = <0x251 0x2>; > + bits = <3 6>; > + }; > + > + tsens_s4_p2: s4-p2@254 { > + reg = <0x254 0x1>; > + bits = <0 6>; > + }; > + }; > + > + tsens: thermal-sensor@4a9000 { > + compatible = "qcom,ipq5018-tsens"; > + reg = <0x4a9000 0x1000>, /* TM */ > + <0x4a8000 0x1000>; /* SORT */ > + > + nvmem-cells = <&tsens_mode>, > + <&tsens_base1>, > + <&tsens_base2>, > + <&tsens_s0_p1>, > + <&tsens_s0_p2>, > + <&tsens_s1_p1>, > + <&tsens_s1_p2>, > + <&tsens_s2_p1>, > + <&tsens_s2_p2>, > + <&tsens_s3_p1>, > + <&tsens_s3_p2>, > + <&tsens_s4_p1>, > + <&tsens_s4_p2>; > + > + nvmem-cell-names = "mode", > + "base1", > + "base2", > + "s0_p1", > + "s0_p2", > + "s1_p1", > + "s1_p2", > + "s2_p1", > + "s2_p2", > + "s3_p1", > + "s3_p2", > + "s4_p1", > + "s4_p2"; > + > + interrupts = <GIC_SPI 184 IRQ_TYPE_EDGE_RISING>; > + interrupt-names = "uplow"; > + #qcom,sensors = <5>; > + #thermal-sensor-cells = <1>; > + }; > + > tlmm: pinctrl@1000000 { > compatible = "qcom,ipq5018-tlmm"; > reg = <0x01000000 0x300000>; > @@ -240,6 +351,64 @@ frame@b128000 { > }; > }; > > + thermal-zones { > + ubi32-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&tsens 1>; > + > + trips { > + ubi32-critical { > + temperature = <120000>; > + hysteresis = <2>; > + type = "critical"; > + }; > + }; > + }; > + > + cpu-thermal { 'c' < 'u'. Please sort the nodes here. > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&tsens 2>; > + > + trips { > + cpu-critical { > + temperature = <120000>; > + hysteresis = <2>; > + type = "critical"; > + }; > + }; > + }; > + > + top-glue-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&tsens 3>; > + > + trips { > + top_glue-critical { > + temperature = <120000>; > + hysteresis = <2>; > + type = "critical"; > + }; > + }; > + }; > + > + gephy-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&tsens 4>; > + > + trips { > + gephy-critical { > + temperature = <120000>; > + hysteresis = <2>; > + type = "critical"; > + }; > + }; > + }; > + }; > + > timer { > compatible = "arm,armv8-timer"; > interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > -- > 2.34.1 >
On 9/24/2023 12:18 AM, Dmitry Baryshkov wrote: > On Fri, 22 Sept 2023 at 14:51, Sricharan R > <srichara@win-platform-upstream01.qualcomm.com> wrote: >> >> From: Sricharan Ramabadhran <quic_srichara@quicinc.com> >> >> IPQ5018 has tsens V1.0 IP with 4 sensors. >> There is no RPM, so tsens has to be manually enabled. Adding the tsens >> and nvmem node and IPQ5018 has 4 thermal sensors (zones). With the >> critical temperature being 120'C and action is to reboot. Adding all >> the 4 zones here. >> >> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> >> --- >> [v3] Ordered the qfprom device node properties as per >> Krzysztof's comments >> >> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 169 ++++++++++++++++++++++++++ >> 1 file changed, 169 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> index 9f13d2dcdfd5..9e28b54ebcbd 100644 >> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> @@ -93,6 +93,117 @@ soc: soc@0 { >> #size-cells = <1>; >> ranges = <0 0 0 0xffffffff>; >> >> + qfprom: qfprom@a0000 { >> + compatible = "qcom,ipq5018-qfprom", "qcom,qfprom"; >> + reg = <0xa0000 0x1000>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + >> + tsens_base1: base1@249 { >> + reg = <0x249 2>; >> + bits = <3 8>; >> + }; >> + >> + tsens_base2: base2@24a { >> + reg = <0x24a 2>; >> + bits = <3 8>; >> + }; > > Sort by the address, please, as usual. > ok. <..> >> >> + thermal-zones { >> + ubi32-thermal { >> + polling-delay-passive = <0>; >> + polling-delay = <0>; >> + thermal-sensors = <&tsens 1>; >> + >> + trips { >> + ubi32-critical { >> + temperature = <120000>; >> + hysteresis = <2>; >> + type = "critical"; >> + }; >> + }; >> + }; >> + >> + cpu-thermal { > > 'c' < 'u'. Please sort the nodes here. ok Regards, Sricharan
On 22. 09. 2023. 13:51, Sricharan R wrote: > From: Sricharan Ramabadhran <quic_srichara@quicinc.com> > > IPQ5018 has tsens V1.0 IP with 4 sensors. > There is no RPM, so tsens has to be manually enabled. Adding the tsens > and nvmem node and IPQ5018 has 4 thermal sensors (zones). With the > critical temperature being 120'C and action is to reboot. Adding all > the 4 zones here. > > Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> > --- > [v3] Ordered the qfprom device node properties as per > Krzysztof's comments > > arch/arm64/boot/dts/qcom/ipq5018.dtsi | 169 ++++++++++++++++++++++++++ > 1 file changed, 169 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > index 9f13d2dcdfd5..9e28b54ebcbd 100644 > --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi > +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > @@ -93,6 +93,117 @@ soc: soc@0 { > #size-cells = <1>; > ranges = <0 0 0 0xffffffff>; > > + qfprom: qfprom@a0000 { > + compatible = "qcom,ipq5018-qfprom", "qcom,qfprom"; Hi, "qcom,ipq5018-qfprom" needs to be documented in QFPROM bindings first. Regards, Robert > + reg = <0xa0000 0x1000>; > + #address-cells = <1>; > + #size-cells = <1>; > + > + tsens_base1: base1@249 { > + reg = <0x249 2>; > + bits = <3 8>; > + }; > + > + tsens_base2: base2@24a { > + reg = <0x24a 2>; > + bits = <3 8>; > + }; > + > + tsens_mode: mode@249 { > + reg = <0x249 1>; > + bits = <0 3>; > + }; > + > + tsens_s0_p1: s0-p1@24b { > + reg = <0x24b 0x2>; > + bits = <2 6>; > + }; > + > + tsens_s0_p2: s0-p2@24c { > + reg = <0x24c 0x1>; > + bits = <1 6>; > + }; > + > + tsens_s1_p1: s1-p1@24c { > + reg = <0x24c 0x2>; > + bits = <7 6>; > + }; > + > + tsens_s1_p2: s1-p2@24d { > + reg = <0x24d 0x2>; > + bits = <5 6>; > + }; > + > + tsens_s2_p1: s2-p1@24e { > + reg = <0x24e 0x2>; > + bits = <3 6>; > + }; > + > + tsens_s2_p2: s2-p2@24f { > + reg = <0x24f 0x1>; > + bits = <1 6>; > + }; > + > + tsens_s3_p1: s3-p1@24f { > + reg = <0x24f 0x2>; > + bits = <7 6>; > + }; > + > + tsens_s3_p2: s3-p2@250 { > + reg = <0x250 0x2>; > + bits = <5 6>; > + }; > + > + tsens_s4_p1: s4-p1@251 { > + reg = <0x251 0x2>; > + bits = <3 6>; > + }; > + > + tsens_s4_p2: s4-p2@254 { > + reg = <0x254 0x1>; > + bits = <0 6>; > + }; > + }; > + > + tsens: thermal-sensor@4a9000 { > + compatible = "qcom,ipq5018-tsens"; > + reg = <0x4a9000 0x1000>, /* TM */ > + <0x4a8000 0x1000>; /* SORT */ > + > + nvmem-cells = <&tsens_mode>, > + <&tsens_base1>, > + <&tsens_base2>, > + <&tsens_s0_p1>, > + <&tsens_s0_p2>, > + <&tsens_s1_p1>, > + <&tsens_s1_p2>, > + <&tsens_s2_p1>, > + <&tsens_s2_p2>, > + <&tsens_s3_p1>, > + <&tsens_s3_p2>, > + <&tsens_s4_p1>, > + <&tsens_s4_p2>; > + > + nvmem-cell-names = "mode", > + "base1", > + "base2", > + "s0_p1", > + "s0_p2", > + "s1_p1", > + "s1_p2", > + "s2_p1", > + "s2_p2", > + "s3_p1", > + "s3_p2", > + "s4_p1", > + "s4_p2"; > + > + interrupts = <GIC_SPI 184 IRQ_TYPE_EDGE_RISING>; > + interrupt-names = "uplow"; > + #qcom,sensors = <5>; > + #thermal-sensor-cells = <1>; > + }; > + > tlmm: pinctrl@1000000 { > compatible = "qcom,ipq5018-tlmm"; > reg = <0x01000000 0x300000>; > @@ -240,6 +351,64 @@ frame@b128000 { > }; > }; > > + thermal-zones { > + ubi32-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&tsens 1>; > + > + trips { > + ubi32-critical { > + temperature = <120000>; > + hysteresis = <2>; > + type = "critical"; > + }; > + }; > + }; > + > + cpu-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&tsens 2>; > + > + trips { > + cpu-critical { > + temperature = <120000>; > + hysteresis = <2>; > + type = "critical"; > + }; > + }; > + }; > + > + top-glue-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&tsens 3>; > + > + trips { > + top_glue-critical { > + temperature = <120000>; > + hysteresis = <2>; > + type = "critical"; > + }; > + }; > + }; > + > + gephy-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&tsens 4>; > + > + trips { > + gephy-critical { > + temperature = <120000>; > + hysteresis = <2>; > + type = "critical"; > + }; > + }; > + }; > + }; > + > timer { > compatible = "arm,armv8-timer"; > interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
On 10/5/2023 12:38 AM, Robert Marko wrote: > > On 22. 09. 2023. 13:51, Sricharan R wrote: >> From: Sricharan Ramabadhran <quic_srichara@quicinc.com> >> >> IPQ5018 has tsens V1.0 IP with 4 sensors. >> There is no RPM, so tsens has to be manually enabled. Adding the tsens >> and nvmem node and IPQ5018 has 4 thermal sensors (zones). With the >> critical temperature being 120'C and action is to reboot. Adding all >> the 4 zones here. >> >> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> >> --- >> [v3] Ordered the qfprom device node properties as per >> Krzysztof's comments >> >> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 169 ++++++++++++++++++++++++++ >> 1 file changed, 169 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> b/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> index 9f13d2dcdfd5..9e28b54ebcbd 100644 >> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi >> @@ -93,6 +93,117 @@ soc: soc@0 { >> #size-cells = <1>; >> ranges = <0 0 0 0xffffffff>; >> + qfprom: qfprom@a0000 { >> + compatible = "qcom,ipq5018-qfprom", "qcom,qfprom"; > Hi, > > "qcom,ipq5018-qfprom" needs to be documented in QFPROM bindings first. Already posted here [1]. Initially had it in the same series, but kept it separately based on review comments. [1] https://www.spinics.net/lists/devicetree/msg633408.html Regards, Sricharan
On Tue, 17 Oct 2023 at 15:07, Sricharan Ramabadhran <quic_srichara@quicinc.com> wrote: > > > > On 10/5/2023 12:38 AM, Robert Marko wrote: > > > > On 22. 09. 2023. 13:51, Sricharan R wrote: > >> From: Sricharan Ramabadhran <quic_srichara@quicinc.com> > >> > >> IPQ5018 has tsens V1.0 IP with 4 sensors. > >> There is no RPM, so tsens has to be manually enabled. Adding the tsens > >> and nvmem node and IPQ5018 has 4 thermal sensors (zones). With the > >> critical temperature being 120'C and action is to reboot. Adding all > >> the 4 zones here. > >> > >> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> > >> --- > >> [v3] Ordered the qfprom device node properties as per > >> Krzysztof's comments > >> > >> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 169 ++++++++++++++++++++++++++ > >> 1 file changed, 169 insertions(+) > >> > >> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi > >> b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > >> index 9f13d2dcdfd5..9e28b54ebcbd 100644 > >> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi > >> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi > >> @@ -93,6 +93,117 @@ soc: soc@0 { > >> #size-cells = <1>; > >> ranges = <0 0 0 0xffffffff>; > >> + qfprom: qfprom@a0000 { > >> + compatible = "qcom,ipq5018-qfprom", "qcom,qfprom"; > > Hi, > > > > "qcom,ipq5018-qfprom" needs to be documented in QFPROM bindings first. > > Already posted here [1]. Initially had it in the same series, but kept > it separately based on review comments. > > [1] https://www.spinics.net/lists/devicetree/msg633408.html Well, if it's not part of the same series then this addition would cause a warning as its undocumented. I also dont see where is it documented as part of the v2 series. Regards, Robert > > Regards, > Sricharan
<..> >>> On 22. 09. 2023. 13:51, Sricharan R wrote: >>>> From: Sricharan Ramabadhran <quic_srichara@quicinc.com> >>>> >>>> IPQ5018 has tsens V1.0 IP with 4 sensors. >>>> There is no RPM, so tsens has to be manually enabled. Adding the tsens >>>> and nvmem node and IPQ5018 has 4 thermal sensors (zones). With the >>>> critical temperature being 120'C and action is to reboot. Adding all >>>> the 4 zones here. >>>> >>>> Signed-off-by: Sricharan Ramabadhran <quic_srichara@quicinc.com> >>>> --- >>>> [v3] Ordered the qfprom device node properties as per >>>> Krzysztof's comments >>>> >>>> arch/arm64/boot/dts/qcom/ipq5018.dtsi | 169 ++++++++++++++++++++++++++ >>>> 1 file changed, 169 insertions(+) >>>> >>>> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi >>>> b/arch/arm64/boot/dts/qcom/ipq5018.dtsi >>>> index 9f13d2dcdfd5..9e28b54ebcbd 100644 >>>> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi >>>> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi >>>> @@ -93,6 +93,117 @@ soc: soc@0 { >>>> #size-cells = <1>; >>>> ranges = <0 0 0 0xffffffff>; >>>> + qfprom: qfprom@a0000 { >>>> + compatible = "qcom,ipq5018-qfprom", "qcom,qfprom"; >>> Hi, >>> >>> "qcom,ipq5018-qfprom" needs to be documented in QFPROM bindings first. >> >> Already posted here [1]. Initially had it in the same series, but kept >> it separately based on review comments. >> >> [1] https://www.spinics.net/lists/devicetree/msg633408.html > > Well, if it's not part of the same series then this addition would > cause a warning as its > undocumented. > > I also dont see where is it documented as part of the v2 series. Then in that case, will keep it in same series again in V4 Regards, Sricharan
diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi index 9f13d2dcdfd5..9e28b54ebcbd 100644 --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi @@ -93,6 +93,117 @@ soc: soc@0 { #size-cells = <1>; ranges = <0 0 0 0xffffffff>; + qfprom: qfprom@a0000 { + compatible = "qcom,ipq5018-qfprom", "qcom,qfprom"; + reg = <0xa0000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + tsens_base1: base1@249 { + reg = <0x249 2>; + bits = <3 8>; + }; + + tsens_base2: base2@24a { + reg = <0x24a 2>; + bits = <3 8>; + }; + + tsens_mode: mode@249 { + reg = <0x249 1>; + bits = <0 3>; + }; + + tsens_s0_p1: s0-p1@24b { + reg = <0x24b 0x2>; + bits = <2 6>; + }; + + tsens_s0_p2: s0-p2@24c { + reg = <0x24c 0x1>; + bits = <1 6>; + }; + + tsens_s1_p1: s1-p1@24c { + reg = <0x24c 0x2>; + bits = <7 6>; + }; + + tsens_s1_p2: s1-p2@24d { + reg = <0x24d 0x2>; + bits = <5 6>; + }; + + tsens_s2_p1: s2-p1@24e { + reg = <0x24e 0x2>; + bits = <3 6>; + }; + + tsens_s2_p2: s2-p2@24f { + reg = <0x24f 0x1>; + bits = <1 6>; + }; + + tsens_s3_p1: s3-p1@24f { + reg = <0x24f 0x2>; + bits = <7 6>; + }; + + tsens_s3_p2: s3-p2@250 { + reg = <0x250 0x2>; + bits = <5 6>; + }; + + tsens_s4_p1: s4-p1@251 { + reg = <0x251 0x2>; + bits = <3 6>; + }; + + tsens_s4_p2: s4-p2@254 { + reg = <0x254 0x1>; + bits = <0 6>; + }; + }; + + tsens: thermal-sensor@4a9000 { + compatible = "qcom,ipq5018-tsens"; + reg = <0x4a9000 0x1000>, /* TM */ + <0x4a8000 0x1000>; /* SORT */ + + nvmem-cells = <&tsens_mode>, + <&tsens_base1>, + <&tsens_base2>, + <&tsens_s0_p1>, + <&tsens_s0_p2>, + <&tsens_s1_p1>, + <&tsens_s1_p2>, + <&tsens_s2_p1>, + <&tsens_s2_p2>, + <&tsens_s3_p1>, + <&tsens_s3_p2>, + <&tsens_s4_p1>, + <&tsens_s4_p2>; + + nvmem-cell-names = "mode", + "base1", + "base2", + "s0_p1", + "s0_p2", + "s1_p1", + "s1_p2", + "s2_p1", + "s2_p2", + "s3_p1", + "s3_p2", + "s4_p1", + "s4_p2"; + + interrupts = <GIC_SPI 184 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "uplow"; + #qcom,sensors = <5>; + #thermal-sensor-cells = <1>; + }; + tlmm: pinctrl@1000000 { compatible = "qcom,ipq5018-tlmm"; reg = <0x01000000 0x300000>; @@ -240,6 +351,64 @@ frame@b128000 { }; }; + thermal-zones { + ubi32-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tsens 1>; + + trips { + ubi32-critical { + temperature = <120000>; + hysteresis = <2>; + type = "critical"; + }; + }; + }; + + cpu-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tsens 2>; + + trips { + cpu-critical { + temperature = <120000>; + hysteresis = <2>; + type = "critical"; + }; + }; + }; + + top-glue-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tsens 3>; + + trips { + top_glue-critical { + temperature = <120000>; + hysteresis = <2>; + type = "critical"; + }; + }; + }; + + gephy-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&tsens 4>; + + trips { + gephy-critical { + temperature = <120000>; + hysteresis = <2>; + type = "critical"; + }; + }; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,